CE Test Report. : Microchip Technology Inc West Chandler Blvd., Chandler, Arizona , USA

Transcription

1

2 CE Test Report Equipment : IEEE b/g Wireless LAN module Brand Name : MICROCHIP Model No. : MRF24WG0MA/MB Standard : EN V1.8.1 ( ) Operating Band : 2400 MHz MHz Applicant Manufacturer : Microchip Technology Inc West Chandler Blvd., Chandler, Arizona , USA The product sample received on Jan. 13, 2014 and completely tested on Nov. 05, We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in EN V1.8.1 ( ) and shown compliance with the applicable technical standards. The equipment under R&TTE Directive 1999/5/EC of article 3.2 harmonized essential for the radio spectrum requirements. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Vic Hsiao / Supervisor SPORTON INTERNATIONAL INC. Page No. : 1 of 86

3 Table of Contents 1 GENERAL DESCRIPTION Information Support Equipment Testing Applied Standards Testing Location Information Measurement Uncertainty TEST CONFIGURATION OF EUT The Worse Case Modulation Configuration The Worse Case Power Setting Parameter The Worst Case Measurement Configuration Test Setup Diagram TRANSMITTER TEST RESULT RF Output Power Power Density Occupied Channel Bandwidth Transmitter Unwanted Emissions in the Out-of-band Domain Transmitter Unwanted Emissions in the Spurious Domain RECEIVER TEST RESULT Receiver Spurious Emissions ADAPTIVITY TEST RESULT Adaptivity and Receiver Blocking TEST EQUIPMENT AND CALIBRATION DATA APPENDIX A. TEST PHOTOS APPENDIX B. PHOTOGRAPHS OF EUT SPORTON INTERNATIONAL INC. Page No. : 2 of 86

4 Summary of Test Result Report Clause Ref. Std. Clause Harmonized Standard Requirements and Conformance Test Specifications Description Measured Limit Result RF Output Power EIRP [dbm]: dbm Complied Power Density EIRP PSD [dbm/mhz] dbm/mhz Complied Duty cycle, Tx-Sequence, Tx-gap Adaptive w/o test EN Clause N/A Medium Utilisation Adaptive w/o test MU > 10% N/A Occupied Channel Bandwidth OCB fall in band Bandwidth [MHz]:16.64 Fall in band Complied Transmitter unwanted emissions in the OOB domain 2487MHz dBm (Margin 18.34dB) EN Figure 3 Complied Transmitter unwanted emissions in the spurious domain [e.i.r.p.]: MHz dBm (Margin 3.68dB) Receiver spurious emissions [e.i.r.p.]: 4944MHz dBm (Margin 1.61dB) EN Table 4 EN Table 5 Complied Complied Adaptivity COT: 1.328ms Idle: 2.16ms Receiver Blocking COT: 1.333ms Idle: 2.184ms IEEE IEEE n IEEE IEEE n Complied Complied SPORTON INTERNATIONAL INC. Page No. : 3 of 86

5 Revision History Report No. Version Description Issued Date ER Rev. 01 Initial issue of report Nov. 21, 2014 SPORTON INTERNATIONAL INC. Page No. : 4 of 86

6 1 General Description 1.1 Information RF General Information Frequency Range (MHz) IEEE Std RF General Information Ch. Frequency (MHz) Channel Number Transmit Chains (N TX ) EIRP - Output Power (dbm) b [13] g [13] Note 1: b uses a combination of DSSS-DBPSK, DQPSK, CCK modulation. Note 2: g uses a combination of OFDM-BPSK, QPSK, 16QAM, 64QAM modulation Antenna Information Integral antenna (antenna permanently attached) Temporary RF connector provided Antenna Category No temporary RF connector provided Transmit chains bypass antenna and soldered temporary RF connector provided for connected measurement. In case of conducted measurements the transmitter shall be connected to the measuring equipment via a suitable attenuator and correct for all losses in the RF path. External antenna (dedicated antennas) Single power level with corresponding antenna(s). Multiple power level and corresponding antenna(s). SPORTON INTERNATIONAL INC. Page No. : 5 of 86

7 < EUT 1 > Antenna General Information No. Brand Name Part Number Gain (dbi) TYPE 1 Aristotle RFA-02-3-C5H1 3 Dipole 2 Aristotle RFA-02-5-C7H1 5 Dipole 3 Aristotle RFA-02-5-F7H1 5 Dipole 4 Aristotle RFA-02-C2M2 2 Dipole 5 Aristotle RFA-02-D3 1.5 Dipole 6 Aristotle RFA-02-L2H1 2 Dipole 7 Aristotle RFA-02-L6H1 2 Dipole 8 Aristotle RFA-02-P05 2 PCB 9 Aristotle RFA-02-P33 2 PCB 10 Roving Networks RN-SMA-S 0.56 Dipole 11 Roving Networks RN-SMA Dipole 12 Roving Networks RN-SMA-7-RP 5 Dipole Note1: This EUT supports 1TX and Port 1 for emission in modulation mode 11b and 11g. Note2: This EUT can match with above antennas for using. Higher gain in each type of antenna was used to perform the worst configuration and result of that was recorded as the final test result. < EUT 2 > Antenna General Information Ant. Cat. Ant. Type Part number Gain (dbi) Integral Printed Remark: This EUT supports 1TX and Port 1 for emission in modulation mode 11b and 11g. SPORTON INTERNATIONAL INC. Page No. : 6 of 86

8 1.1.3 Type of EUT Identify EUT EUT Serial Number N/A Presentation of Equipment Production ; Pre-Production ; Prototype Type of EUT Stand-alone Combined (EUT where the radio part is fully integrated within another device) Combined Equipment - Brand Name / Model No.: Plug-in radio (EUT intended for a variety of host systems) Host System - Brand Name / Model No.: Other: Test Signal Duty Cycle Operated normally mode for worst duty cycle Operated test mode for worst duty cycle Test Signal Duty Cycle (x) Operated Mode for Worst Duty Cycle Power Duty Factor [db] (10 log 1/x) 53.25% - IEEE b % - IEEE g 0.06 SPORTON INTERNATIONAL INC. Page No. : 7 of 86

9 1.1.5 Medium Access Protocol Medium Access Protocol Medium Access Protocol: IEEE Std IEEE Std n-2009 IEEE Std IEEE Std Other: A medium access protocol has been implemented by the equipment. With mechanism designed to facilitate spectrum sharing with other devices in a wireless network. The equipment implements an adequate spectrum sharing mechanism and users will be equal access wireless network EUT Operational Condition Supply Voltage AC mains DC Type of DC Source Internal DC supply External DC adapter From Host System Test Voltage Vnom (3.30 V) Test Climatic Tnom (20 C) Tmax (85 C) Tmin (-40 C) Adaptive Equipment non-adaptive Equipment: Adaptive Equipment The maximum RF Output Power (e.i.r.p.): dbm The maximum (corresponding) Duty Cycle: % Adaptive Equipment without the possibility to switch to a non-adaptive mode: The equipment has implemented an LBT based DAA mechanism: The equipment is Frame Based equipment The equipment is Load Based equipment The equipment can switch dynamically between Frame Based and Load Based equipment The equipment has implemented an non-lbt based DAA mechanism The equipment can operate in more than one adaptive mode Adaptive Equipment which can also operate in a non-adaptive mode SPORTON INTERNATIONAL INC. Page No. : 8 of 86

10 1.2 Support Equipment Support Equipment RF Conducted No. Equipment Brand Name Model Name 1 Notebook DELL E Test Fixture - - Support Equipment Radiated Emission No. Equipment Brand Name Model Name 1 Adapter CUI EPAS-101W-05 2 Test Fixture - - Support Equipment Adaptivity No. Equipment Brand Name Model Name 1 AP (Master) EDIMAX EW-7438RPN 2 Notebook DELL E Notebook DELL E Adapter CUI EPAS-101W-05 5 Test Fixture - - Note: The test fixture was provided by customer. 1.3 Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: EN V1.8.1 ( ) 1.4 Testing Location Information Testing Location HWA YA ADD : No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL : Test Condition Test Site No. Test Engineer Test Environment RF Conducted TH01-HY Jack 22.1 C / 61% Radiated Emission 05CH01-HY Max 23 C / 61% Adaptivity DFS01-HY Ben 26 C / 60% SPORTON INTERNATIONAL INC. Page No. : 9 of 86

11 1.5 Measurement Uncertainty ISO/IEC requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Test Item Uncertainty Limit Radio Frequency ± 8.7 X 10-7 ± 1 X 10-5 RF output power, conducted ±0.7 db ±1.5 db Power density, conducted ±1.3 db ±3 db Unwanted emissions, conducted MHz ±0.6 db ±3 db GHz ±0.7 db ±3 db All emissions, radiated MHz ±2.3 db ±6 db GHz ±2.6 db ±6 db Temperature ±0.8 C ±1 C Humidity ±3 % ±5 % DC and low frequency voltages ±3 % ±3 % SPORTON INTERNATIONAL INC. Page No. : 10 of 86

12 2 Test Configuration of EUT 2.1 The Worse Case Modulation Configuration Worst Modulation Used for Conformance Testing Modulation Mode Transmit Chains (N TX ) Data Rate / MCS Worst Data Rate / MCS 11b Mbps 1 Mbps 11g Mbps 6 Mbps 2.2 The Worse Case Power Setting Parameter The Worst Case Power Setting Parameter ( MHz band) Test Software Version alphacom Modulation Mode N TX Test Frequency (MHz) NCB: 20MHz b A 11g 1 2F SPORTON INTERNATIONAL INC. Page No. : 11 of 86

13 2.3 The Worst Case Measurement Configuration The Worst Case Mode for Following Conformance Tests Tests Item Test Condition Modulation Mode RF Output Power, Power Density, Occupied Channel Bandwidth Transmitter unwanted emissions in the OOB domain Conducted measurement at transmit chains 11b, 11g The Worst Case Mode for Following Conformance Tests Tests Item Test Condition Transmitter Unwanted Emissions in The Spurious Domain, Receiver Spurious Emissions Radiated measurement If EUT consist of multiple antenna assembly (multiple antenna are used in EUT regardless of spatial multiplexing MIMO configuration), the radiated test should be performed with highest antenna gain of each antenna type. EUT will be placed in fixed position. User Position EUT will be placed in mobile position and operating multiple positions. EUT shall be performed three orthogonal planes. The worst plane is X(for Dipole and PCB) and Y(for Printed). EUT will be a hand-held or body-worn battery-powered devices and operating multiple positions. Operating Mode Transmit / Receive 1 Dipole 2 PCB 3 Printed Modulation Mode 11b, 11g X Plane Y Plane Z Plane Orthogonal Planes of EUT The Worst Case Mode for Following Conformance Tests Tests Item Test Condition Modulation Mode Adaptivity & Receiver Blocking Conducted measurement at transmit chains 11b, 11g SPORTON INTERNATIONAL INC. Page No. : 12 of 86

14 2.4 Test Setup Diagram Test Setup Diagram - Radiated Test (Mode1) EUT Dipole Ant. RF cable Test Fixture AC Main Test Setup Diagram - Radiated Test (Mode2) EUT PCB Ant. RF cable Test Fixture AC Main SPORTON INTERNATIONAL INC. Page No. : 13 of 86

15 Test Setup Diagram - Radiated Test (Mode3) EUT Printed Ant. Test Fixture AC Main SPORTON INTERNATIONAL INC. Page No. : 14 of 86

16 3 Transmitter Test Result 3.1 RF Output Power RF Output Power Limit RF Output Power Limit Type of Equipment Using Wide Band Modulations Other than FHSS: mean equivalent isotropic radiated power (e.i.r.p.) 20 dbm Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method The measurements shall be performed at both normal environmental conditions and at the extremes of the operating temperature range. Refer as EN , clause for conducted measurement. The EUT supports single transmit chain and measurements performed on this transmit chain 1. The EUT supports diversity transmitting and the results on transmit chain port 1 is the worst case. The EUT supports multiple transmit chains using options given below: Option 1: Sample all transmit ports simultaneously using a power sensor for each transmit port. Sum the power of all ports for each individual sample and save them. Option 2: In case of conducted measurements on smart antenna systems (devices with multiple transmit chains) a power splitter/combiner shall be used to combine all the transmit chains (antenna outputs) into a single test point. The insertion loss of the power splitter/combiner shall be taken into account. If multiple transmit chains, EIRP calculation could be following as methods: P total = P 1 + P P n (calculated in linear unit [mw] and transfer to log unit [dbm]) EIRP total = P total + G If more than one antenna assembly is intended for this power setting, the maximum overall antenna gain (G or G + Y) shall be used for EIRP. Refer as EN , clause for radiated measurement Test Setup RF Output Power SPORTON INTERNATIONAL INC. Page No. : 15 of 86

17 3.1.5 Maximum Antenna Gain Maximum Antenna Gain Result Transmit Chains No Maximum Gain (dbi)-g Modulation Mode N TX N SS (Min.) G+Y (dbi) 11b g If more than one antenna assembly is intended for this power setting, the maximum overall antenna gain (G or G + Y) shall be used for EIRP. SPORTON INTERNATIONAL INC. Page No. : 16 of 86

18 3.1.6 Test Result of RF Output Power Test Date Aug. 13, 2014 Maximum Transmit Power (dbm) Condition Modulation Mode N TX Freq. (MHz) Output Power DG (dbi) EIRP Power EIRP Limit TnomVnom 11b TminVnom 11b TmaxVnom 11b TnomVnom 11b TminVnom 11b TmaxVnom 11b TnomVnom 11b TminVnom 11b TmaxVnom 11b Result Complied Test Date Aug. 13, 2014 Maximum Transmit Power (dbm) Condition Modulation Mode N TX Freq. (MHz) Output Power DG (dbi) EIRP Power EIRP Limit TnomVnom 11g TminVnom 11g TmaxVnom 11g TnomVnom 11g TminVnom 11g TmaxVnom 11g TnomVnom 11g TminVnom 11g TmaxVnom 11g Result Complied SPORTON INTERNATIONAL INC. Page No. : 17 of 86

19 3.2 Power Density Power Density Limit Power Density Limit Type of Equipment Using Wide Band Modulations Other than FHSS: mean equivalent isotropic radiated power (e.i.r.p.) density 10 dbm/mhz Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method Refer as EN , clause for conducted measurement. The EUT supports single transmit chain and measurements performed on this transmit chain1. The EUT supports diversity transmitting and the results on transmit chain port 1 is the worst case. The EUT supports multiple transmit chains using given below: For conducted measurements on devices with multiple transmit chains: Sample all transmit ports simultaneously using a spectrum analyzer for each transmit port. Where the trace bin-by-bin of each transmit port summing can be performed. (i.e., in the first spectral bin of output 1 is summed with that in the first spectral bin of output 2 and that from the first spectral bin of output 3, and so on up to the N TX output to obtain the value for the first frequency bin of the summed spectrum.). Add up the amplitude (power) values for the different transmit chains and use this as the new data trace. The new data trace samples added 1 MHz segment and found the highest value of each 1 MHz segments. If multiple transmit chains, EIRP calculation could be following as method: EIRP total = P total + DG Refer as EN , clause for radiated measurement Test Setup Power Density SPORTON INTERNATIONAL INC. Page No. : 18 of 86

20 3.2.5 Test Result of Power Density Test Date Aug. 13, 2014 Maximum e.i.r.p. Spectral Density Result Modulation Mode N TX Freq. (MHz) Max. Gain (dbi) EIRP PD (dbm/mhz) EIRP Limit (dbm/mhz) 11b b b g g g Result Complied SPORTON INTERNATIONAL INC. Page No. : 19 of 86

21 3.3 Occupied Channel Bandwidth Occupied Channel Bandwidth Limit Type of Frequency Hopping Equipment: Occupied Channel Bandwidth Limit Occupied Channel Bandwidth for each hopping frequency fall completely within 2.4 GHz GHz. For non-adaptive equipment with e.i.r.p greater than 10 dbm, Occupied Channel Bandwidth 5 MHz. Type of Equipment Using Wide Band Modulations Other than FHSS: Occupied Channel Bandwidth fall completely within 2.4 GHz GHz. For non-adaptive equipment with e.i.r.p greater than 10 dbm, Occupied Channel Bandwidth 20 MHz Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method Refer as EN , clause for conducted measurement. The EUT supports single transmit chain and measurements performed on this transmit chain1. The EUT supports diversity transmitting and the results on transmit chain port 1 is the worst case. Refer as EN , clause for conducted measurements on smart antenna systems (equipment with multiple transmit chains) measurements need only to be performed on one of the active transmit chains (antenna outputs). All measurement had be performed on transmit chains 1. Refer as EN , clause clause for radiated measurement Test Setup Emission Bandwidth SPORTON INTERNATIONAL INC. Page No. : 20 of 86

22 3.3.5 Test Result of Occupied Channel Bandwidth Test Date Aug. 13, 2014 Occupied Channel Bandwidth Result Modulation Mode Frequency (MHz) 99% Bandwidth (MHz) F L at 99% BW (MHz) F H at 99% BW (MHz) 11b b g g Limit N/A Result Complied SPORTON INTERNATIONAL INC. Page No. : 21 of 86

23 3.4 Transmitter Unwanted Emissions in the Out-of-band Domain Transmitter Unwanted Emissions in the Out-of-band Domain Limit Transmit Mask Limit Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method The measurements shall be performed at both normal environmental conditions and at the extremes of the operating temperature range. Refer as EN , clause for conducted measurement. The EUT supports single transmit chain and measurements performed on this transmit chain1. The EUT supports diversity transmitting and the results on transmit chain port 1 is the worst case. The EUT supports multiple transmit chains using options given below: Option 1: the results for each of the transmit chains for the corresponding 1 MHz segments shall be added and compared with the transmit mask limit. Option 2: the results for each of the transmit chains shall be individually compared with the transmit mask limit. After that these limits have been reduced with 10 x log 10 (A ch ). (Number of active transmit chains). Refer as EN , clause for radiated measurement. SPORTON INTERNATIONAL INC. Page No. : 22 of 86

24 3.4.4 Test Setup Transmitter Unwanted Emissions in the Out-of-band Domain SPORTON INTERNATIONAL INC. Page No. : 23 of 86

25 3.4.5 Test Result of Transmitter Unwanted Emissions in the Out-of-band Domain Test Date Aug. 13, 2014 OOB Emissions (dbm/mhz) Condition Modulation Mode N TX Freq. (MHz) OOB Freq. (MHz) OOB Emissions TnomVnom 11b TminVnom 11b TmaxVnom 11b TnomVnom 11b TminVnom 11b TmaxVnom 11b Limit Low Band Up Band Result Complied SPORTON INTERNATIONAL INC. Page No. : 24 of 86

26 Test Date Aug. 13, 2014 OOB Emissions (dbm/mhz) Condition Modulation Mode N TX Freq. (MHz) OOB Freq. (MHz) OOB Emissions TnomVnom 11g TminVnom 11g TmaxVnom 11g TnomVnom 11g TminVnom 11g TmaxVnom 11g Limit Low Band Up Band Result Complied SPORTON INTERNATIONAL INC. Page No. : 25 of 86

27 3.5 Transmitter Unwanted Emissions in the Spurious Domain Transmitter Unwanted Emissions in the Spurious Domain Limit Frequency Range Maximum Power e.r.p. ( 1 GHz) ; e.i.r.p. (>1 GHz) Bandwidth 30 MHz to 47 MHz -36 dbm 100 khz 47 MHz to 74 MHz -54 dbm 100 khz 74 MHz to 87,5 MHz -36 dbm 100 khz 87,5 MHz to 118 MHz -54 dbm 100 khz 118 MHz to 174 MHz -36 dbm 100 khz 174 MHz to 230 MHz -54 dbm 100 khz 230 MHz to 470 MHz -36 dbm 100 khz 470 MHz to 862 MHz -54 dbm 100 khz 862 MHz to 1 GHz -36 dbm 100 khz 1 GHz to 12,75 GHz -30 dbm 1 MHz Note 1: spurious domain (2400 MHz 2N) and spurious domain ( MHz + 2N); N = MAX (1, Occupied Channel Bandwidth) MHz Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method Refer as EN , clause for conducted measurement. Conducted spurious emissions and radiated by the cabinet with the antenna connector(s) terminated by a specified load (cabinet radiation). The EUT supports single transmit chain and measurements performed on this transmit chain. The EUT supports diversity transmitting and the results on transmit chain port 1 is the worst case. The EUT supports multiple transmit chains using options given below: Option 1: The trace data for each transmit chain has to be individually recorded and each transmit chain trace data shall be added and compared with the transmitter spurious emissions limit. Option 2: the results for each of the transmit chains shall be individually compared with the transmitter spurious emissions limit. After that these limits have been reduced with 10 x log 10 (A ch ). (Number of active transmit chains). Equipment with single transmit chain. All measurement had be performed on this transmit chain. Refer as EN , clause for radiated measurement. SPORTON INTERNATIONAL INC. Page No. : 26 of 86

28 3.5.4 Test Setup Transmitter Unwanted Emissions in the Spurious Domain A measuring distance of at least 3 m shall be used for measurements at frequencies up to 1 GHz. For frequencies above 1 GHz, any suitable measuring far field distance may be used, depending on the test system noise floor for detecting spurious emission signals. The equipment size (excluding the antenna) shall be less than 20 % of the measuring distance. The height of the equipment or of the substitution antenna shall be 1.5 m. SPORTON INTERNATIONAL INC. Page No. : 27 of 86

29 3.5.5 Transmitter Radiated Unwanted Emissions (Below 1GHz) Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Mode 11g Polarization V Operating Mode 1 Operating Function Transmit (Mode 1) Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 28 of 86

30 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Mode 11g Polarization H Operating Mode 1 Operating Function Transmit (Mode 1) Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 29 of 86

31 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Mode 11g Polarization V Operating Mode 2 Operating Function Transmit (Mode 2) Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 30 of 86

32 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Mode 11g Polarization H Operating Mode 2 Operating Function Transmit (Mode 2) Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 31 of 86

33 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Mode 11g Polarization V Operating Mode 3 Operating Function Transmit (Mode 3) Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 32 of 86

34 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation Mode 11g Polarization H Operating Mode 3 Operating Function Transmit (Mode 3) Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 33 of 86

35 3.5.6 Transmitter Radiated Unwanted Emissions (Above 1GHz) for 11b Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F1 Operating Function Transmit (Mode 1) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 34 of 86

36 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F1 Operating Function Transmit (Mode 1) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 35 of 86

37 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F3 Operating Function Transmit (Mode 1) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 36 of 86

38 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F3 Operating Function Transmit (Mode 1) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 37 of 86

39 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F1 Operating Function Transmit (Mode 2) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 38 of 86

40 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F1 Operating Function Transmit (Mode 2) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 39 of 86

41 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F3 Operating Function Transmit (Mode 2) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 40 of 86

42 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F3 Operating Function Transmit (Mode 2) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 41 of 86

43 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F1 Operating Function Transmit (Mode 3) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 42 of 86

44 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F1 Operating Function Transmit (Mode 3) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 43 of 86

45 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F3 Operating Function Transmit (Mode 3) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 44 of 86

46 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11b Test Freq. (FX) F3 Operating Function Transmit (Mode 3) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 45 of 86

47 3.5.7 Transmitter Radiated Unwanted Emissions (Above 1GHz) for 11g Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F1 Operating Function Transmit (Mode 1) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 46 of 86

48 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F1 Operating Function Transmit (Mode 1) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 47 of 86

49 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F3 Operating Function Transmit (Mode 1) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 48 of 86

50 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F3 Operating Function Transmit (Mode 1) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 49 of 86

51 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F1 Operating Function Transmit (Mode 2) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 50 of 86

52 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F1 Operating Function Transmit (Mode 2) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 51 of 86

53 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F3 Operating Function Transmit (Mode 2) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 52 of 86

54 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F3 Operating Function Transmit (Mode 2) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 53 of 86

55 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F1 Operating Function Transmit (Mode 3) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 54 of 86

56 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F1 Operating Function Transmit (Mode 3) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 55 of 86

57 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F3 Operating Function Transmit (Mode 3) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 56 of 86

58 Transmitter Radiated Spurious Emissions (Above 1GHz) Modulation Mode 11g Test Freq. (FX) F3 Operating Function Transmit (Mode 3) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 57 of 86

59 4 Receiver Test Result 4.1 Receiver Spurious Emissions Receiver Spurious Emissions Limit Frequency Range Maximum Power e.r.p. ( 1 GHz) ; e.i.r.p. (>1 GHz) Bandwidth 30 MHz to 1 GHz -57 dbm 100 khz 1 GHz to 12,75 GHz -47 dbm 1 MHz Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method Refer as EN , clause for conducted measurement. Conducted spurious emissions and radiated by the cabinet with the antenna connector(s) terminated by a specified load (cabinet radiation). The EUT supports single receive chain and measurements performed on this receive chain. The EUT supports diversity receiving and the results on receive chain port 1 is the worst case. The EUT supports multiple receive chains using options given below: Option 1: The trace data for each receive chain has to be individually recorded and each receive chain trace data shall be added and compared with the receiver spurious emissions limit. Option 2: the results for each of the receive chains shall be individually compared with the receiver spurious emissions limit. After that these limits have been reduced with 10 x log 10 (A ch ). (Number of active receive chains). Refer as EN , clause for radiated measurement. SPORTON INTERNATIONAL INC. Page No. : 58 of 86

60 4.1.4 Test Setup Receiver Spurious Emissions A measuring distance of at least 3 m shall be used for measurements at frequencies up to 1 GHz. For frequencies above 1 GHz, any suitable measuring far field distance may be used, depending on the test system noise floor for detecting spurious emission signals. The equipment size (excluding the antenna) shall be less than 20 % of the measuring distance. The height of the equipment or of the substitution antenna shall be 1.5 m. SPORTON INTERNATIONAL INC. Page No. : 59 of 86

61 4.1.5 Receiver Radiated Spurious Emissions (Below 1GHz) Receiver Radiated Spurious Emissions (Below 1GHz) Operating Mode 1 Operating Function Receive (Mode 1) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 60 of 86

62 Receiver Radiated Spurious Emissions (Below 1GHz) Operating Mode 1 Operating Function Receive (Mode 1) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 61 of 86

63 Receiver Radiated Spurious Emissions (Below 1GHz) Operating Mode 2 Operating Function Receive (Mode 2) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 62 of 86

64 Receiver Radiated Spurious Emissions (Below 1GHz) Operating Mode 2 Operating Function Receive (Mode 2) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 63 of 86

65 Receiver Radiated Spurious Emissions (Below 1GHz) Operating Mode 3 Operating Function Receive (Mode 3) Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 64 of 86

66 Receiver Radiated Spurious Emissions (Below 1GHz) Operating Mode 3 Operating Function Receive (Mode 3) Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 65 of 86

67 4.1.6 Receiver Radiated Spurious Emissions (Above 1GHz) Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 1) Test Freq. (FX) F1 Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 66 of 86

68 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 1) Test Freq. (FX) F1 Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 67 of 86

69 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 1) Test Freq. (FX) F3 Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 68 of 86

70 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 1) Test Freq. (FX) F3 Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 69 of 86

71 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 2) Test Freq. (FX) F1 Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 70 of 86

72 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 2) Test Freq. (FX) F1 Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 71 of 86

73 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 2) Test Freq. (FX) F3 Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 72 of 86

74 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 2) Test Freq. (FX) F3 Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 73 of 86

75 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 3) Test Freq. (FX) F1 Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 74 of 86

76 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 3) Test Freq. (FX) F1 Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 75 of 86

77 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 3) Test Freq. (FX) F3 Polarization V Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 76 of 86

78 Receiver Radiated Spurious Emissions (Above 1GHz) Operating Function Receive (Mode 3) Test Freq. (FX) F3 Polarization H Note 1: >6dB means spurious emission levels that exceed the level of 6 db below the applicable limit. Note 2: N/F means Nothing Found spurious emissions (No spurious emissions were detected.) Note 3: Measurement receive antenna polarization: H (Horizontal), V (Vertical) SPORTON INTERNATIONAL INC. Page No. : 77 of 86

79 5 Adaptivity Test Result 5.1 Adaptivity and Receiver Blocking Adaptivity and Receiver Blocking Limit Adaptivity and Receiver Blocking Limit Type of Equipment Using Wide Band Modulations Other than FHSS: Only for adaptive systems and RF Output Power > 10 dbm Non-LBT based Detect and Avoid: minimum remain unavailable = 1sec; minimum Idle Period time = 100us; maximum Channel Occupancy Time (COT) = 40ms i.e. COT [40ms] + Idle Period [2ms - 5% of COT]; N x [COT+Idle]; detection threshold level = -70 dbm/mhz Pout e.i.r.p. (Pout in dbm); LBT based Detect and Avoid (Frame Based Equipment): minimum Clear Channel Assessment (CCA) time = 20 us; CCA declared by the supplier COT = 1 ms to 10 ms Idle Period = 5% of COT e.g. CCA [120us] + COT [10ms] + Idle Period [0.5ms - 5% of COT]; detection threshold level = -70 dbm/mhz Pout e.i.r.p. (Pout in dbm); LBT based Detect and Avoid (Load Based Equipment with spectrum sharing mechanism IEEE Std.): LBT based spectrum sharing mechanism may implement IEEE Std clauses 15, 17, 18 or 19, in IEEE Std n-2009, clause 20 or in IEEE Std , LBT based Detect and Avoid (Load Based Equipment): minimum Clear Channel Assessment (CCA) time = 20 us; COT (13 / 32) x q ms; q=[4..32] ; 1.625ms 13ms; R = number of clear idle slots are randomly [1..q]. Every time an Extended CCA is required and the R value stored in a counter. Extended CCA = R x CCA i.e. for channel occupied then R = 4 idle slots; COT [1.625ms; q=4]; idle slots [1] - Extended CCA [60us, R=3]; detection threshold level = -70 dbm/mhz Pout e.i.r.p. (Pout in dbm); Short Control Signalling Transmissions: Short Control Signalling Transmissions shall have a maximum duty cycle of 10 % within an observation period of 50 ms. Equipment Type LBT Non-LBT Wanted Signal Mean Power from Companion Device Receiver Blocking Parameters Blocking Signal Frequency (MHz) sufficient to maintain the link (see note 2) 2395 or 2488,5 (see note 1) -30 dbm Blocking Signal Mean power (dbm) Type of Interfering Signal -30 CW Note 1: The highest blocking frequency shall be used for testing the lowest operating hopping frequency, while the lowest blocking frequency shall be used for testing the highest hopping frequency. Note 2: A typical value which can be used in most cases is -50 dbm/mhz. SPORTON INTERNATIONAL INC. Page No. : 78 of 86

80 5.1.2 Measuring Instruments Refer a test equipment and calibration data table in this test report Test Procedures Test Method Configure the EUT for normal transmissions with a sufficiently high payload to allow demonstration the adaptive mechanism. Refer as EN , clause for conducted measurement. The EUT supports single receive chain and measurements performed on this receive chain. For conducted measurements on devices with multiple transmit chains and receive chains. The power splitter/combiner shall be used to combine all the transmit/receive chains (antenna outputs) into a single test point. The insertion loss of the power splitter/combiner shall be taken into account. Refer as EN , clause for radiated measurement Test Setup Adaptivity and Receiver Blocking Radiated Method SPORTON INTERNATIONAL INC. Page No. : 79 of 86