Engineering Drawing Practices

Transcription

1 ASME Y [Revision of ASME Y (R2009) and Consolidation of ASME Y (R2008)] Engineering Drawing Practices Engineering Drawing and Related Documentation Practices AN AMERICAN NATIONAL STANDARD

2 ASME Y ADOPTION NOTICE ASME Y14.100, Engineering Drawing and Related Documentation Practices, was adopted on 30 January 1998 for use by the Department of Defense, DoD. Proposed changes by DoD activities must be submitted to the DoD Adopting Activity: Commander, U.S. Army ARDEC, ATTN: AMSRD-AAR-AIS-SS, Picatinny Arsenal, NJ or ed to Copies of this document may be purchased from The American Society of Mechanical Engineers (ASME), 22 Law Drive, P.O. Box 2900, Fairfield, NJ ; Custodians: Army AR Navy SA Air Force 16 DLA DH Adopting Activity: Army AR (Project DRPR ) Review Activities: Army AV, CR, MI, PT, TE, TM Navy AS, CG, CH, MC Air Force 04, 13, 99 DLA IS OSD SE Other MP, DC2, NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at

3 ASME Y [Revision of ASME Y (R2009) and Consolidation of ASME Y (R2008)] Engineering Drawing Practices Engineering Drawing and Related Documentation Practices AN AMERICAN NATIONAL STANDARD Two Park Avenue New York, NY USA

4 Date of Issuance: July 30, 2013 This Standard will be revised when the Society approves the issuance of a new edition. There will be no written interpretations of the requirements of this Standard issued to this edition. Periodically certain actions of the ASME Y14 Committee may be published as Cases. Cases are published on the ASME Web site under the Committee Pages at as they are issued. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at There is an option available to automatically receive an notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting Errata in the Publication Information section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not approve, rate, or endorse any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. The American Society of Mechanical Engineers Two Park Avenue, New York, NY Copyright 2013 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reserved Printed in U.S.A.

5 CONTENTS Foreword... Committee Roster... Correspondence With Y14 Committee... Summary of Changes... v vi vii viii Section 1 General Scope Application ASME Y14 Series Conventions Reference to This Standard... 2 Section 2 References... 2 Section 3 Definitions... 4 Section 4 General Drawing Practices Nonmandatory Appendix B Noncommercial Drawing Practices Types and Application of Engineering Drawings Associated Lists Revisions of Engineering Drawings and Associated Lists Size and Format of Engineering Drawings Application Data Preparation of Duplicate Original Line Conventions and Lettering Single, Multiple, and Sectional View Drawings Isometric and Pictorial Views Projection Systems Dimensioning and Tolerancing Surface Texture Screw Thread Representation Gears Mechanical Springs Optical Elements and Optical Systems Castings, Forgings, and Molded Parts Composite Parts Graphic Symbols, Designations, Letter Symbols, and Abbreviations Logic Circuit Diagrams Printed Boards Digital Data Scale Marking for Item Identification Optional/Alternative Designs Drawing Notes Drawing Verification and Approval Dating Drawings Digital Approval Systems Reference Identifiers In-House Peculiar Information Use of Specifications and Standards Metric Practices Section 5 Drawing Titles iii

6 5.1 Nonmandatory Appendix C Drawing Titles General Rules Section 6 Numbering, Coding, and Identification Nonmandatory Appendix D Numbering, Coding, and Identification Drawing Numbers Special Characters Drawing Number Prefixes and Suffixes Drawing Identification and Ownership Part or Identifying Number Reference to Items Item Identification Model Number or Catalog Number Serial Number Version Number Database Number Section 7 Markings on Drawings Nonmandatory Appendix E Markings on Engineering Drawings Items and Processes Special Notations Marking for Special Items and Processes Feature Identification Symbology Notes Item Replacement Notations Rights in Data Legends on Drawings Duplicate Original Duplicate Production Master (Stable Base Artwork) Reproductions From Digitally Maintained Data Ozone-Depleting Substances Nonmandatory Appendix F Classification Codes for Drawings and Data Sets Figures 6-1 Drawing Notations Indicating a Transfer of Design Responsibility Symbology Duplicate Original Notation Duplicate Production Master Drawing Notation Tables 3-1 Example of Common Product Definition Elements for Drawing Graphic Sheets and Data Sets Acronyms for Special Items and Processes Nonmandatory Appendices A Tailoring B Noncommercial Drawing Practices C Drawing Titles D Numbering, Coding, and Identification E Markings on Engineering Drawings F Classification Codes for Drawings and Data Sets Index iv