ecotile Interlocking floor tiles

Transcription

1 ecotile Interlocking floor tiles A quick, simple & sustainable flooring solution The World s No.1 Range of Interlocking Floor Tiles and ESD Flooring

2 ecotile Interlocking floor tiles Tough enough for industry, smart enough for retail. A quick, simple and sustainable flooring solution. Description ecotile interlocking floor tiles are a tough, flexible and modern flooring solution. ecotile is available in four surface textures and a variety of colours. The tiles are manufactured in either a traditional open joint or a smart hidden joint design as well as specialist ESD, anti-static and ergonomic versions. ecotile can usually be installed without the requirement for a damp proof membrane, screed or adhesive, significantly reducing installation time and cost. Composition & Manufacture ecotile is injection moulded using compound that has excellent wear characteristics, chemical resistance, long term stability and stable electrical properties. Applications ecotile has been used in factories, schools and offices across Europe for over 25 years. Designed to cope with heavy vehicle and fork lift truck traffic, ecotile offers good thermal and acoustic insulation and excellent resistance to impact and vibration. Factories Passenger Terminals Warehouses Schools Garages Retail Outlets Sports Facilities Exhibitions An Environmentally Sustainable Solution ecotile is produced from the highest quality raw material. Once the tiles have reached the end of their useful life we will collect the tiles, free of charge, and recycle them to produce the next generation of ecotile. Key Benefits Extremely Hard Wearing Low Life Cycle Cost And Simple To Maintain Smart & Modern Appearance ESD / Anti-static Version Available Ideal For Use With Fork Trucks And Heavy Loads Quick And Simple To Install, No Downtime Good Anti-slip Properties Protects The Existing Floor From Damage Versatile, Quick And Easy To Amend Design or Layout Ideal For Uneven, Damp Or Contaminated Substrates Excellent value Manufactured in the UK - ISO 9001 Accreditation 10 Year Product Warranty

3 ecotile standard colour range & surface textures ecotile E500/7-500 x 500 x 7mm and 500 x 500 x 10mm Tiles ecotile 7mm Smooth ecotile 7mm Raised Disk ecotile 10mm Smooth Light Grey Black Dark Blue Red Light Grey Dark Grey Black Dark Grey Dark Grey Green Yellow Blue Dark Blue ecotile E500/6-500 x 500 x 6mm Tile ecotile 6mm Smooth Light Grey Dark Blue Terracotta ecotile 6mm Raised Disk ecotile 6mm Durbar Light Grey Dark Grey Dark Grey ecotile 6mm Slate Graphite Grey Dark Grey ecotile ESD - Conductive/Dissipative & Anti-static Flooring. BS EN 61340/5 Compliant x 500 x 7mm Tiles ecotile 7mm ESD/Conductive/ Dissipative & Anti-static Dark Grey Green Blue Mid Grey ecotile S500 ergonomic flooring & ecotile R500 Recycled Floor Tiles 500 x 500 x 7mm ecotile S500/7-7mm Raised Disk ecotile R500/7-7mm Smooth Texture Dark Grey Graphite Grey Black SPECIAL ORDERS If you require a special colour please contact us. We can manufacture in almost any RAL colour subject to the following terms and conditions: Minimum 10% cost surcharge subject to colour. Minimum 6 to 8 week lead time from date of order. Minimum order quantity 150m² Set up / colour proof charge of 350 per special colour. We are unable to accept returns, cancellations or amendment once the order has been placed. ESD500 AS502 S500/220 R500/221 R500/101 Note: Please be aware that in the dark grey 500/ESD the stainless steel fibres may be visible on the surface of the tile. This is a unavoidable and ensures optimum ESD performance.

4 ecotile 500/7 The Original Loose Lay Interlocking Tile. Where and why to use ecotile 500/7: ecotile 500/7 is the original loose lay interlocking floor tile. It is 7mm thick tile with an open joint dovetail design. Ideal for the vast majority of applications, ecotile 500/7 is a heavy duty floor covering that can withstand high point loading, impact and vibration. Ideal for heavy foot and vehicle traffic including fork lift trucks (as a guide up to 3.5 ton unladen weight). If in doubt please contact your sales representative and / or check out the ecotile extra heavy duty 500/10 tile. See also our hidden joint, ESD, anti-static and comfort range. Hard Wearing: ecotile 500/7 is the world s number one interlocking floor tile manufactured from hard wearing 100% recyclable PVC. ecotile can be installed without the need for a DPM, screed or adhesive significantly reducing VOC emissions, installation time and cost. ecotile is manufactured in two levels of hardness suitable for various applications varying from a soft tile for schools and shops (see S500/7) to a hard tile ideal for factories and warehouses. Easy to Install: ecotile 500/7 can be installed without the requirement for a damp proof membrane, screed or adhesive significantly reducing VOC emissions, installation time and cost. Durable: ecotile 500/7 is injection moulded using compound that has excellent wear characteristics, chemical resistance, long-term stability and stable electrical properties. Key Benefits Extremely Hard Wearing. Quick And Simple To Install, No Downtime. Good Anti-slip Properties Protects The Existing Floor From Damage. Ideal For Uneven, Damp Or Contaminated Substrates. 10 year Product Warranty Applications: ecotile 500/7 has been used in factories, schools and offices across Europe for over 25 years. Designed to cope with heavy vehicle and fork lift truck traffic, ecotile offers good thermal and acoustic insulation and excellent resistance to impact and vibration. Factories & Warehouses Shops & Offices Garages & Workshops Sports & Leisure Facilities Railway Stations & Airports Schools & Colleges Exhibitions & Point of Sale Prisons, Police & Fire Stations

5 ecotile 500/6 The Loose Lay Tile With The Hidden Joint. Where and why to use ecotile 500/6: ecotile 500/6 has a hidden joint with a push fit seam and bevelled edge which has a similar appearance to a traditional vinyl tile finish. The performance is almost identical to ecotile 500/7 but has been designed to provide an alternative for customers who do not want or like the open joint design. The push fit seam offers better protection to water ingress and is therefore more popular within food preparation areas, shops, laboratories etc.. The interlocking floor tiles with the hidden joint: ecotile 500/6: Interlocking floor tiles are a tough, flexible and modern flooring solution. ecotile 500/6 is available in four surface textures and a variety of colours. The tiles have a bevelled hidden joint that creates a smooth smart appearance. ecotile 500/6 can be installed without the requirement for a damp proof membrane, screed or adhesive significantly reducing VOC emissions, installation time and cost Composition & Manufacture: ecotile 500/6 is injection moulded using compound that has excellent wear characteristics, chemical resistance, long term stability, good stability and stable electrical properties. An Environmentally Sustainable Solution: ecotile 500/6 is produced from the highest quality material. Once the tiles have reached the end of their useful life we will collect the tiles, free of charge, and recycle them to produce the next generation of ecotile. Key Benefits Low Life Cycle Cost And Simple To Maintain. Smart & Modern Appearance. Quick And Simple To Install, No Downtime. Good Anti-slip Properties Protects The Existing Floor From Damage. Versatile, Quick And Easy To Amend Design or Layout. 10 year Product Warranty. Applications: ecotile 500/6 has been used in shops, factories, schools and offices. ecotile 500/6 offers good thermal and acoustic insulation and is easy and simple to clean and maintain. Schools & Colleges Shops & Offices Garages Sports Facilities Passenger Terminals Exhibitions & Point of Sale Utility Rooms Light Industrial Units

6 ecotile 500/10 Ultra Heavy Duty Floor Tiles Where and why to use ecotile 500/10: ecotile 500/10 has been used to repair and protect busy warehouse and factory floors where access time is limited. The 10mm tile is recommended for use in areas where heavier fork trucks, aisle stackers or narrow aisle trucks are used or where HGV s will be executing tight manoeuvres or rotating wheels whilst stationary. ecotile 500/10 has also proven extremely successful in aircraft hangers and fire station pump room floors. The ultra heavy duty interlocking floor tiles are exceptionally tough, resistant to impact, heavy loads and high traffic movements. ecotile 500/10 is the highest specification tile we produce and as with the entire range has been designed to be loose laid and is therefore quick and simple to install. Composition & Manufacture: ecotile 500/10 is injection moulded using compound that has excellent wear characteristics, chemical resistance, long term stability, good stability and stable electrical properties. Key Benefits Extremely Tough & Hard Wearing. Excellent Resistance To Impact & Vibration Protects The Existing Floor From Damage. No Floor Preparation Or Adhesive Required Low Life Cycle Cost & Easy To Maintain Good Anti-slip Properties Suitable For Floors that Are Subject To Exceptionally Heavy Wear. Quick And Simple To Install, No Downtime. Good Anti-slip Properties Ideal For Old, Uneven, Damp, Oily Or Contaminated Substrates. Insulates Against Cold, Damp & Noise Applications: ecotile 500/10 can be used almost anywhere and is the tile to specify if you have any concerns about the loads that will be travelling across the floor or the levels of abuse and or impact that the floor will be subject to. Engineering Plants Passenger Terminals Warehouses Food Factories Commercial Garages Shopping Centres Free Weight Areas Fire Stations Power Stations Distribution Centres Aircraft Hangars Maintenance Depots

7 ecotile 500/7/ESD Conductive /Dissipative Floor Tiles The patented ESD / anti-static interlocking floor tile: ecotile 500/7/ESD can be used as your primary ground and is guaranteed to give ESD performance for the life of the tile. The electrostatic dissipative (ESD / EPA) interlocking floor tiles are ideal for use in electronics and telecommunications factories, computer server rooms, production plants such as pharmaceutical, paint, petrochemical and certain food production facilities with risk of dust explosion (sugar, flour dust etc.) Composition & Manufacture: ecotile 500/7/ESD is manufactured from tough PVC compound incorporating millions of tiny stainless steel metal fibres. ecotile has excellent wear characteristics, chemical resistance, long term stability, good weatherability and stable electrical properties. Performance & Test Results : ecotile 500/7/ESD has been independently tested: Surface resistivity: 2.2 x 104Ω to 3 x 106Ω Resistance to ground: 2.9 x 104Ω to 5.7 x 105Ω Electrostatic Propensity:< 10 Volts / <2.0 kv Static Decay at 15% humidity: 0.01sec The test results guarantee that ecotile ESD complies with British Standard BS EN :2007 and IEC EN/ISO 61340/5, EN 1081, EN1815 & EN6356 ESD Flooring - Resistance to Ground EN/ISO 61340/5, EN 1081, EN1815 & EN6356 ESD Flooring - Surface Resistance ecotile 502/7/AS Anti-static Floor Tiles ecotile 502/7/AS is an anti-static floor tile with a surface resistance between 3.0 x 10 9 Ω and 3.4 x Ω. At these levels the floor will not generate static electricity but neither will it dissipate away any latent charge that an individual had built up. ecotile 502/7/AS is suitable for areas where the risk of electrostatic damage to components is low. Composition & Manufacture: ecotile 502/7/AS is manufactured from tough PVC compound incorporating a chemical additive that provides the anti-static performance. Performance & Test Results Surface resistivity: 3.0 x 10 9 Ω and 3.4 x Ω EN/ISO 61340/5, EN 1081, EN1815 & EN6356 Anti-static Floor Covering

8 ecotile S500/7 The Softer Tile With Improved Ergonomics. Where and why to use: ecotile S500/7 is the softer and more flexible version of ecotile, it is not suitable for use with fork lifts or pallet trucks. ecotile S500/7 has been used with great success to provide a comfortable work surface, to protect products or goods from damage through impact with hard floors, around machinery and benches and behind counters and bars to delay the onset of worker fatigue. At low temperatures (below zero centigrade) the tiles adopt the same performance characteristics as the standard 7mm ecotile making it ideal for cold stores and freezers. Composition & Manufacture: ecotile S500/7 is manufactured in the same way as the standard ecotile but with a higher percentage of plasiticser and elastomer to create the softer feel. Applications Assembly lines Shop counters Around Machinery For product protection Freezer rooms Laboratories Baggage collection Creches ecotile logo tiles: Add impact to your EcoTile Floor by incorporating permanent floor markings. ecotile are able to incorporate almost any logo or image into your ecotile floor to create a permanent and highly visual sign or message, The logo tiles are manufactured by CNC water laser jet cutting which ensures a clean and precise cut. The only restriction on design is the colour range of ecotile which is limited to black, light grey, dark grey, green, royal blue french blue, red, yellow, terra-cotta and white (plus occasionally a few special colours, subject to availability). Company logo tiles: Place your sales message or logo where it will really get noticed and enhance your company s image and profile. Badges & Insignia: Almost any design can be incorporated into your ecotile floor. Hazard Warning / Floor Safety Signs: Statutory Health and Safety Regulations require every company ensure that the appropriate Health and Safety Signs are displayed throughout all premises. We are able to manufacture the full range of warning signs (black & yellow), prohibitory signs (red & white) and mandatory signs (blue and white). Applications In-Shop Displays / POS Exhibition Stands Demonstration Areas Identifying Safety Hazards Showrooms Guidance for Fire Exits Traffic Demarcation / Mandatory Warning Signs Pedestrian Crossings

9 ecotile accessories The ecotile product range is supplied with a full range of accessories to allow us to complete the perfect installation: Code Description ecotile Ramps, Diminishing Strips & Thresholds E ecotile 500/7 clip on ramp sections available in all standard colours. Dimensions: 500mm x 70mm x 7mm>1mm E ecotile 500/7 clip on ramp corner sections available in all standard colours. Dimensions: 590mm x 70mm x 7mm>1mm PCR6 ecotile 500/6 stick on ramp sections / diminishing strips. Available in black, dark grey and light grey. Dimensions: 2000mm x 32mm x 7mm>1mm AR268FO Heavy duty aluminium ramp section 2700mm x 80mm x 8.5mm >1mm ACS441 Aluminium cover strip for thresholds or expansion joints 2700mm x 40mm ecotile pipeweld adhesive for attaching stick on ramp sections 125ml ecotile PVC-U skirting boards ecotile PVC-U skirting board 2.5m length - DARK GREY ONLY. Dimensions: 2500mm x 100mm x 15mm ecotile PVC-U skirting board 5m length - White Satin, English Oak or Rosewood. Dimensions: 5000mm x 100mm x 15mm ecotile PVC-U skirting board internal Corner ecotile PVC-U skirting board External Corner ecotile PVC-U skirting board in line connector kit Webfix Gap filling Adhesive for ecotile skirting ecotile floor repair, levelling compounds & adhesives A46 Moisture Resistant Rapid Set Patch Repair Compound Feather Finish self levelling smoothing compound MK92S 2 Component adhesive for gluing ecotile (use in areas where tiles will be in direct sun / high temperature variations.) ecotile cleaners, specialist sealers & polishes Anti-colour stain prevention sealer - Use to prevent plasticiser migration from rubber tyres, colour dyes etc..) * Anti-slip Sealer * Heavy duty polyurethane floor sealer * All products marked * require application by qualified installers, please contact us for further details Rotex General Purpose Floor Cleaner Distance General Purpose Floor Sealer Viper Heavy Duty Floor Stripper ecotile esd accessories ESD Grounding Kit (Consists grounding tape, studded tile, plug & earthing cord with 1 meg ohm resistor) - 1 kit required per 80 to 100m² of esd flooring ESD Floor Marking Tile

10 Technical & Environmental Fact Sheet: Standards and Accreditation - Meets & exceeds requirements of BS EN 685:1996 (Resilient and Homogeneous and heterogeneous PVC floor coverings), BBA 96/3229/3 laminate floor coverings) and BS EN 649:1997 (Resilient Floor coverings). Life Cycle Cost - ecotile is a loose laid system so in the event of damage or excessive wear individual tiles can be lifted and replaced significantly extending the life of the floor and reducing the life cycle cost. Sustainability - ecotile is 100% recyclable, at the end of its service life the tiles can be granulated and re-used to manufacture a new floor. Most floor coverings only have a limited life span due to wear or the building occupier s wishes to refurbish or alter the building s appearance. Most waste floor coverings will end up in land fill due to the fact that once it has been adhered to the floor it cannot be re-used. Not only can ecotile be recycled but there is a strong market for pre-owned tiles Anticipated Service Life - 25 years + VOC Content - Trace elements of volatiles from modifiers and non PVC based additives. Significantly lower VOC levels when compared to resin based flooring systems or the levels encountered when using adhesives to stick down conventional floor coverings. ecotile contains no formaldehyde and carries a class E1 rating Sound Absorption - Noise reduction of up to 46db can be achieved Hardness - Standard ISO 868 ecotile 6mm, 7mm and 10mm Shore A / ecotile comfort 76 Shore Slip Resistance / Anti-Slip Qualities: EN 14041: Pass - Average Reading in excess of 0.6 dynamic coefficient of friction DIN 51130: R10 Rating - Suitable for use in areas where there is an increased risk of slipping due to grease, oil water etc.. EN 13893:2002 Dynamic Coefficient of Friction = 0.75 avg. Surface EN14041: Dynamic coefficient of friction DIN Determination of slip resistance. Raised Disk 0.56 R10 Smooth 0.67 R10 Durbar 0.52 R9 Slate 0.65 R10 All tests undertaken by SATRA Technology Centre - Test certificates available Fire Performance - ecotile does not support combustion and achieves Class 1 spread of flame when tested to BS 476: Part 7 / DIN 13501: Bfl-S1 Abrasion Wear - Group T (<0.1mm /100 revs) (EN / EN13845) Mechanical Resistance - 17 N/mm2 to DIN / Density - BS EN 436 Determination of Length, Squareness & Straightness - BS EN 428: <0.13% / 0.5mm max Thickness - BS EN to 9.24mm +/- 0.15mm Determination of Residual Indentation - BS EN 433: <0.1mm / Dimensional Stability - BS EN 434:1994 Maximum change in dimension <0.1% / Compressive Strength - ISO :1994, ISO :1994, ISO :1996: 520kg/cm² Chemical Resistance - Good resistance to most commonly used chemicals. ecotile offers good short to medium term resistance but as with most materials long term exposure could result in damage to the elastomer, colour and stability of the tile. In the event of accident we recommend the tiles are cleaned as soon as possible and if necessary lifted to remove any chemical that may have seeped underneath. EN Common acids oils & gas oil No deterioration / Solvents Not resistant to prolonged contact Colour Fastness / Resistance to natural light: EN B021-5 (no damage) Cleaning - Day-to-day cleaning - Use a rotary scrubber dryer or damp mopping Electrical Properties - ecotile Standard: surface resistivity: and Ω / ecotile ESD: surface resistivity: 3 x 10 6 Ω and 2.2 x 10 4 Ω / Resistance to ground : 5.7 x 10 5 Ω and 2.9 x 10 4 Ω / ecotile Anti-static: surface resistivity: 3 x 10 9 Ω and 2.2 x Ω Tests were carried out in accordance with the requirements of Annex A.1 of BS IEC :2007. ecotile ESD fulfils the recommendations detailed in BS EN :2007 for floors to be used for primary grounding. Resistance to Hot Objects/Solder - Good RAL Colours - Due to the manufacturing process we cannot guarantee a precise match to a RAL colour and the following list is provided as a guide only: Black - RAL9017, Light Grey - RAL7004, Dark Grey , Dark Blue - RAL5013, Green - RAL6026, Red - RAL3020, Terracotta Red - RAL3009, Yellow - RAL1023, French Blue RAL5017, Stone - RAL1015. Usage Classification - Code of Practice BS 8203:2001 / EN 685 Class 43 The CE marking certifies that a product has met EU consumer safety, health or environmental requirements. ecotile carries the CE marking and is manufactured to and corresponds with the criteria detailed for PVC flooring as detailed in EN ecotile llp & The Versatile Flooring Company Ltd are a BS EN ISO9001:2008 accredited company. Certificate No: AJA11/15057

11 ecotile interlocking floor tiles - Guidelines & Terms & Conditions of Sale The following guidelines have been prepared to assist you with the specification, installation and use of ecotile. The list is not exhaustive but covers the key points and the lessons we have learnt over the past 15 years of business. Failure to adhere to the guidelines may invalidate your warranty and in the event that any rectification or repair work is required ecotile reserves the right to charge for any making good or repairs. General Guidelines In the vast majority of ecotile applications no adhesive is required; the tiles can be dry laid and will take forklift or vehicle traffic without a problem. The tiles may require gluing if there is the risk of high shear pressure (for example a three wheel electric reach truck with the batteries located over the back wheel operating in a confined space with very tight turning circles) or high point loading (for example when using skates to move heavy machinery). If such events are only likely to happen occasionally, rather than gluing we recommend placing hard board over the tiles temporarily, which will protect the tiles and make the move easier. ecotile is not recommended for use outdoors If ecotile is being installed in an area exposed to direct sunlight (e.g. loading bay doors) or in an area where there are extremes of temperature it may be necessary to glue the tiles. Contact us for further advice. ecotile must be fitted with a 5mm expansion gap between the tiles and any fixed point (walls and machinery) The minimum temperature at which ecotile can be installed is 15ºC. The tiles must be stored within the installation area at a minimum temperature of 15ºC for at least 24 hours prior to commencing installation. If installation is taking place during cold periods leave a larger expansion gap (10mm). ecotile offers good resistance to petrol and other hydrocarbons, however in the event of prolonged and excessive exposure the elastomer in the tiles can be damaged and may result in the tiles curling. In the event of a spillage clean the tiles and if you suspect the chemical has got under the tiles we recommend lifting and cleaning the underside of the tiles. Rubber tyres (car, motorbike & fork truck) contain a chemical that can cause staining on ecotile as well as other types of floor coverings (vulcanisation / plasticiser migration). This will not damage the tiles but we recommend using a darker colour to minimise the impact of the staining. For non industrial applications we recommend applying a sealer to the floor to help aid maintenance and cleaning. This is particularly important if you are using a light coloured tile (light grey, stone and yellow). Contact ecotile for further information or download the cleaning and maintenance guidelines from the download section on our website. Installations being undertaken by ecotile The tiles must be left in the installation area to acclimatise for a minimum of 24 hours before installation commences. ecotile reserves the right to charge for any unforeseen repair work / alterations that may be required to allow installation to be completed, for example if the floor has been damaged by the removal of the old floor finish or to trim doors to fit. In the event that we are undertaking installation please be aware that it is the customer's responsibility to ensure that the installation area is as clear as possible. The great advantage of ecotile is that it can be laid without the need to remove machinery; racking benches etc. but to make the job as efficient as possible we request that pallets, boxes, computers etc. are moved or placed on table tops so that our installation team can concentrate on fitting your new floor. Failure to adhere to the guidelines may invalidate your warranty and in the event that any rectification or repair work is required ecotile reserves the right to charge for any making good or repairs. ecotile & ecotile ESD product warranty: ecotile llp. Warrants, for the period of ten years from the date of installation that its range of interlocking floor tiles will not deform, degrade or distort and that in the event of any of these things occurring we will replace the defective material free of charge provided that : The tiles are installed in accordance with ecotile installation instructions (specifically that installation has taken place when the temperature is above 15 degrees centigrade and a minimum of a 5mm gap has been left between the tiles and any fixed points, walls etc.). The ecotile floor has been subject to normal wear and tear and has not been subject to physical misuse or vandalism. Furthermore we warrant that the ecotile esd range will retain its esd performance for the life of the product and that the ecotile antistatic range will retain its anti-static properties for 2 years. The warranty does not extend to: Damage caused by chemicals or hydrocarbons that have not been tested or are not detailed within the technical data section of our brochure. ecotile offers good resistance to most commonly used chemicals and hydrocarbons with the specific exception of toluene or its derivatives. If customers are concerned we recommend that they undertake their own tests prior to installing ecotile. Markings from rubber tyres (car, motorbike, fork truck etc.) cigarettes or other burning agents or staining of the surface of ecotile by acetone, cutting oils and lubricants (in particular those containing sulphur) or colour fading caused by exposure to UV / sunlight. Liability for failure or damage to the material by circumstances beyond ecotile control, including failures due to flooding, storm damage or the failure of the sub-floor. ecotile will investigate any claim made under this warranty and shall only be liable under the terms of this warranty if such investigation shows that the ecotile floor has been installed and maintained according to the above specification. The liability of ecotile llp is limited to supplying, free of charge, sufficient material to replace that found to be defective.

12 Life Cycle Cost & Environmental Impact: ecotile can usually be installed without the need for any sub-floor preparation and no adhesives are required saving on materials, labour and harmful VOC emissions. ecotile has an anticipated life span in excess of 25 years. When the floor has reached the end of its usable life, ecotile can be quickly and simply lifted and, because there is no contamination from adhesive or screed, the tiles can be 100% recycled. Appearance & Colours: ecotile is available in nine standard colours and four finishes. Special colours available on request. Installation (For detailed instructions please refer to our Installation guidelines): ecotile is quick and simple to install and the tiles do not require a DPM or gluing to the floor. Installation should only be undertaken when the tiles have been allowed to acclimatise to the ambient temperature of the room (minimum 15 degrees centigrade). Start installation of the open joint from the centre of the room and the hidden joint from one corner of the room ensuring that you leave a 5mm gap between the tiles and the wall. Install all full size tiles, allow the floor to settle and then cut tiles to fit up to walls and fixed points leaving a 5mm gap for expansion between the tiles and any fixed point. Cleaning & Maintenance: Sweep regularly to remove particle dirt and occasionally damp mop or use a rotary scrubber dryer to clean the floor using a neutral ph floor cleaner diluted in between 1:80 and 1:50. Application of a hard wearing floor sealer will help maintain the appearance of the floor and extend its lifespan. Please contact us for detailed cleaning and maintenance instructions and a list of approved products. Accessories: Please refer to price list for the full list of accessories including ramps, corners, skirting, adhesives and sealers. Product Data EN Homogenous Flooring EN ASTM F1303 ENHANCED SLIP: Sustainable wet slip resistance EN 14041: Pass / DIN51130: R10 - Suitable for use in areas where there is an increased risk of slipping due to grease, oil water etc. Mean surface roughness Rz 37μm The slip resistance across all ecotile products is assured throughout the guaranteed life of the product, with strict adherence to HSE Guidelines. REACTION TO FIRE: EN Class Bfl-S1 EN ISO kw/m² EN ISO Pass / ASTM E648 Class 1 EN 423 GOOD EN K cycles EN 649 Group T Thickness of wear layer EN to 10mm Impact Resistance EN kg/cm² Noise Reduction EN >46db Notes: * relates to the ecotile 500/7/ESD and E502/7/AS tiles only. * EN/ISO 61340/5, EN 1081, EN1815 & EN6356 Resistance to Ground * EN/ISO 61340/5, EN 1081, EN1815 & EN Surface Resistance * EN/ISO 61340/5, EN 1081, EN1815 & EN Anti-static Floor Covering Format Dimensions Thickness Weight/m² Tile 500 x 500mm 6.3, 7 or 10mm 7.3 to 12kgs Colours Surface Finish Pack Size Coverage per pack/m² Various Smooth, raised disk, slate or durbar 10 tiles 2.5m² For further information contact: Proudly manufactured in the UK