GE Proficy Machine Edition Profibus/Profinet SARTUP GUIDE

Transcription

1 GE Proficy Machine Edition Profibus/Profinet SARTUP GUIDE G1028 Published 8/28/2013

2 Table of Contents Table of Contents... 1 About This Guide... 2 Required Parts... 3 Hardware... 3 Software... 3 Target Files... 3 Setup... 4 GE Proficy Machine Edition Setup... 4 Setting the rotary dials for Proibus... 7 Setting the dip switches for Proifbus... 7 Setting the rotary dials for Profinet Rotary Dials Rotary Dials... 8 Dip Switches... 8 Setting the Ethernet address via the software... 9 Web Configuration... 9 Pactware... 9 IP Addressing Installing GSD/GSDML files in the hardware configuration Adding a device onto Profibus/Profinet network Adding a Profibus device onto the network Adding a Profinet device onto the network TURCK Profibus Manuals

3 About This Guide This manual is intended to supplement the GE Proficy Machine Edition documentation. This document will go through a brief introduction on creating a project in the GE Proficy Software and then will focus on installing, configuring, and troubleshooting Turck Profibus / Profinet devices. 2

4 Required Parts Hardware GE PACSystems RX3i Turck BL20-GW-DPV1 Turck BL20-E-GW-EN Software GE Proficy Machine Edition Turck GSD(ML) Files Target Files Target files are required for Turck Programmable Gateways. The only applicable gateway for Profibus is the BL67-PG-DP.Turck Target Files 3

5 GE Proficy Machine Edition Setup Setup It is assumed that there is working knowledge of GE Proficy Machine Edition. If not, please refer to the GE Proficy Machine Edition Manual. Create a New project in Proficy using New Project Wizard or Open Project File > New Project For a new project, insert the Project Name, Project Template, and Project location. When done click OK. 4

6 Once the project is in Proficy, Right click on the Processor and select the CPU. Click OK To add the Profinet Controller, right click on the slot the Profinet card is in the chassis and in the pop up window click Add Module 5

7 In the Catalog Window, click on the Bus Controller Tab and select communication master. In our example, the RX3i Profibus Master and RX3i Profinet Controller are used. Click OK. 6

8 Setting the rotary dials for Profibus There are two rotary dials on the BL20, BL67, BLCDP, FGDP. The left rotary dial is the high byte (0..F). The right rotary dial is the low byte (0..F). Available addresses for the Profibus Network are Field bus address 0, 126, 127 are not available for addressing. Setting the dip switches for Profibus The BL20-E-GW uses Dip Switches instead of the Rotary Dials. The Gateway s bus address results from the addition of valences (2 0 to 2 6 ) of the switched DIP-switches (position = 1) The BL20-E-GW-DP allows the Activation of the Resistor R T using the last to Dip Switches. Both Switches must be set to On to activate the Profibus Resistor 7

9 Setting the rotary dials for Profinet Depending on the Turck Product being used there are either 2 or 3 rotary dials on the gateway. The dial is used to set the last Octet of the IP address (x.x.x.1-254). The first three octets will be set through the internet explorer or Pactware or the Turck IP Address tool. 3 Rotary Dials 2 Rotary Dials Dip Switches 8

10 Setting the Ethernet address via the software Web Configuration To configure the IP Address using the Web Configuration, open Internet Explorer and Type in the IP address of the gateway you are connecting to. Pactware Pactware is a useful troubleshooting, simulating and monitoring tool for Turck gateways and I/O attached to the gateway. If Pactware is not installed, click to direct you to the Pactware I/O Assistant Software. Click on the Full to download Pactware to your computer. With the Turck gateways connected, open the Pactware software. It will bring the dialog box up to select Hart Modem, Turck BL Service RS232, or Turck BL Service TCP-IP. Select Turck BL Service TCP-IP Once selected, it will add the Ethernet driver to the Project Side in Pactware. Double Click on TCP/IP to open the BusAddress Management screen. Click on the Eye in the Bus address Management screen to search for available gateways on the network. Once all the Turck devices on the network have been found, click on the Add Device/DTM to project (The battery with a plus sign). This will add the Device to the Project window. Also, it will add all I/O attached to the Gateway to the project window for simulating and monitoring. 9

11 IP Addressing In Turck products, the IP addressing can be set by either connecting to the Turck Gateway through Pactware, the IP address tool, or through Internet Explorer or modifying the first three octets of the IP Address. The last octet will be set by the rotary dials or dip switches. - Right click on the Profinet Controller in the Navigator Window. Select Launch Discovery Tool in the Pop up Window - Click on Refresh Device List to bring list of devices on the network. - Select device to be modified and click edit device. 10

12 - In the properties window, the Device Name and IP address can be changed. You can also reset the device to factory defaults and identify the device on the network. When identifing the device, the LEDs on the gateway will flash. When Done click on the exit button 11

13 Installing GSD / GSDML files in the hardware configuration In the Toolchest window click on the dropdown arrow and select a Profibus /Profinet Device. Right mouse click on the Toolchest window, click Assistants -> Add GSD File 12

14 - Browse to the folder where the GSD file is located. - Select file(s). Click Open. - Note: All files with.gsd are the default GSD files in the English language. Other versions may include GSE (English), GSF (French), and GSG (German) languages. - All Profinet files are.xml files. 13

15 Adding a device onto Profibus / Profinet network Adding a Profibus device onto the network. Depending on the PLC defined in the configuration, there may be multiple Profinet or Profibus Nodes. In this example, only one Profibus and one Profinet node is used. It is assumed the PLC has been defined in the hardware configuration. - To add a Profibus device onto a network, Click on the device from the Toolchest and drag it to the Navigator window onto the Profibus or Profinet card. - When the station is added to the network, a configuration window will popup and allow the Name, station Number to be modified. Also the Modules to be added to the gateway and the gateway parameters can be modified - To Add I/O modules to the gateway, select on the module tab and click on the Add button 14

16 - Select the module and click OK - To change the parameters of the individual module click on the I/O module and click the Properties button. 15

17 Adding a Profinet device onto the network. - Click on the Profinet Devices drop down in the Toolchest - Click on the folder to open the folder - Click on the GSDML file and drag it to the Profinet card. 16

18 - Once it is under the Profinet, click on the gateway and the device name and IP Address will be in the Inspector. This must match the configuration downloaded to the gateway when using the network discovery tool. - Right mouse click on the device to open the Properites window 17

19 - This will bring up the GW parameters for Profinet. - Right mouse click on the device to change the Module List 18

20 - Select modules associated with the Profinet Gateway. Click OK - To change the parameters of the module, right click on the module and select configure 19

21 - After changing the parameters click the X to close the window. 20

22 Turck Profibus / Profinet Manuals Profibus BL67-PG-DP BL67-GW-DPV1 BL20-GW-DPV1 BL20-E-GW-DP Profinet BL67-GW-EN BL20-GW-EN BL20-E-GW-EN FXEN* 21