Instructions for assembly and use MULTICAL 601
|
|
- Rosanna Morgan
- 7 years ago
- Views:
Transcription
1 Instructions for assembly and use MULTICAL 601
2 1.1 MID labelling Standard conditions of operation/measuring rates: Meter θ: 10 C 180 C Θ: 3K 170K A pair of resistance temperature sensors θ: 10 C 150 C Θ: 3K 140K Flow meter θ: 15 C 130 C Mechanical environment: M1 (solid installation with minimal vibrations). Electromagnetic environment: E1 a E2 (house units, light industry, and industry). Signalling cables from the meter must be lead at a minimum distance of 25 cm from other installations. Climatic environment: This product is intended for interior installation only; it must be installed in a non-condensing environment. The temperature of the environment must be between 5 and 55 C. Maintenance and repair: The keeper is allowed to exchange the communication module, battery, temperature sensors (a pair), and the flow meter. The temperature sensor pair and flow meter are verified separately (independent from the calculator), and thus can be exchanged individually. All repairs require a consequent verification in an accredited laboratory. MULTICAL 601, type 67-B/C/D is suitable for the Pt500 temperature sensors MULTICAL 601, type 67-A is suitable for the Pt100 temperature sensors Battery for an exchange: Kamstrup MULTICAL 601, type 67-A/B/C can be connected to the ULTRAFLOW flow meter; to a unit with an electronic collector; or to a flow meter with a Reed contact. MULTICAL 601, type 67-D, must be connected to a flow meter with an active 24 V impulse output. No matter what the flow meter type is, the imp/l must be the same on both the flow meter and calculator.
3 MULTICAL 601 & ULTRAFLOW English Kamstrup A/S Industrivej 28, Stilling, DK-8660 Skanderborg PHONE NO.: FAX:
4 1. General information Before installing the power meter, study this guide carefully. In case the meter is not properly installed, the Kamstrup Company withdraws all its warranty commitments. Please, notice that it is necessary to meet the following installation conditions: - ULTRAFLOW compression stage: PN16/PN25/PN40, see the ; labelling. The flow meter labelling does not concern the accessories supplied. - Kamstrup compression stage of DS temperature sensors: - The compression stage of stainless steel containers: PN16 PN25/PN40 according to the type If the medium temperature exceeds 90 C, we recommend using flange meters, and mounting the MULTICAL 601 on a wall. 2. Temperature sensor assembly Temperature sensors used for measuring supply and return temperatures form a pair; they must never be separated form each other. MULTICAL 601 is usually supplied with mounted temperature sensors. According to the EN 1434 and OIML R75 standards, their cable length must not be changed. If the sensors need to be exchanged, the complete pair must always be replaced. The red marked sensor must be placed in the supply piping. The other sensor has a blue marking, and must be mounted into the return piping. 2.1 Container sensors It is best to mount the container sensors into T-shaped branches or 45 Y-branches. The end of the container must be placed in the direction of flow, and in the centre of water flow.
5 Temperature sensors must be inserted all the way to the bottom of the containers. If a short period of response is required, a non-setting heat conductive paste may be used. Insert the plastic case of the sensor cable into the sensor container, and fasten the cable with the supplied M4 screw, which has an opening for a sealing wire. The screw is only to be tightened with your fingers. Seal the containers using the seal and wire. 2.2 Short direct temperature sensors Short direct sensors can be mounted into special ball valves or special T-parts. Both contain threads up to the R1 size, and a built-in M10 clutch for a short direct sensor. For assembly into existing heating installations equipped with standard T-shaped branches, the Kamstrup A/S Company is able to supply brass inserts of R½ and R¾ size, suitable for short direct sensors. Short direct sensors can also be installed directly into all ULTRAFLOW machine versions, with G¾ and G1 threads, on the flow parts of the meter. Fasten the brass sensor inserts lightly (to ca 4 Nm), using a 12 mm wrench, and seal the sensors with seal and wire.
6 3. Information E codes MULTICAL 601 continuously monitors a range of important functions. In case of serious damage in the measuring system or installation, an Info note appears on the display. The information code can be read by pressing and holding the left top button, until the Info note shows up on the display. The information code only appears if there is an error. Information Time of Code Description response 000 No error Supply voltage disconnected T1 temperature sensor out of the measuring range 1 to 10 min. 004 T2 temperature sensor out of the measuring range 1 to 10 min. 032 T3 temperature sensor out of the measuring range 1 to 10 min. 064 Cold water system leak 24 hrs 256 Heating system leak 24 hrs 512 Heating system crack Ca 120 sec 4. Assembly of the flow section Before the assembly of the flow section, carefully wash the system and remove protective lids (plastic diaphragms). The correct flow meter position (in supply and return piping) is shown on the label of the MULTICAL 601 front. The direction of the flow is marked with an arrow on the side of the flow meter. Pipe union and sealing must be mounted as given in the picture. ULTRAFLOW does not require any direct sections in front of and behind the meter; however, to reach the optimal installation conditions, we recommend the following: Dimensions Recommendation DN15 to DN80 qp 0.6 to qp 40 Min. 5 x DN in front of the meter DN100 to DN250 qp 60 to qp 1000 Min. 10 x DN in front of the meter Min. 3 x DN in front of the meter CEN CR installation requirements must be followed.
7 To prevent cavitations, the ULTRAFLOW operating pressure must be min. 1.5 bar for qp min. 2.5 bar for qs (4.5 bar for DN80). This requirement is valid for temperatures up to approx. 80 C. ULTRAFLOW must not be exposed to pressures lower than the pressure of surrounding environment (vacuum). 4.1 ULTRAFLOW assembly ULTRAFLOW must be installed in either horizontal or vertical position, or under any angle in between these two positions. ULTRAFLOW can be rotated up to ±45, according to the piping axis. ULTRAFLOW must not be mounted so that the black plastic cover is pointed either up or down.
8 Assembly example: MULTICAL can be mounted in two positions using angle bracket. The angle bracket needs to be ordered separately Dampness and condensation In case ULTRAFLOW is installed in a damp environment, it must be turned in a 45 angle to the piping axis, as you can see below. If condensation is to be expected (e.g. in cooling systems), the ULTRAFLOW, which is protected from condensation must be used. 5. Calculator assembly The MULTICAL 601 calculator can be assembled in three different ways: 5.1 Compact assembly The calculator is mounted straight onto the flow part. If needed, an angle bracket can be used. After the assembly, the calculator must be sealed with a seal and a wire. If the condensation is high (e.g. in cooling systems), we recommend to mount the calculator on a wall. See also paragraph 4.1 ULTRAFLOW assembly.
9 5.2 Separate assembly on the wall The bracket for wall mounting enables you to mount MULTICAL 601 directly onto a straight wall. Use the bracket for marking and drilling two holes, 6 mm in diameter, into the wall. 5.3 Assembly in a panel MULTICAL 601 can be mounted straight into panels, using the panel assembly set Kamstrup, no (192 x 144 mm). 6. Power supply MULTICAL 601 can be powered by a built-in lithium battery; 24 VAC internal supply module; or 230 VAC internal power module. Two conductors from the battery or main voltage module are connected to 60 and 61 calculator clips. When connecting the conductors, polarity must be kept; connect the red conductor into clip no. 60 (+), and black conductor into clip no. 61 (-). 6.1 Battery supply MULTICAL 601 is connected to a lithium battery (cell D). The battery is marked with installation year, e.g. 2007, and production year. Optimum battery life is reached if the battery is not exposed to temperatures above 30 C, e.g. by placing it on a wall. Lithium battery voltage remains constant for most of its life (ca 3.65 V). The remaining battery capacity thus cannot be determined by voltage measuring. The battery cannot be, and is not allowed to be, recharged; it also must not be shortcircuited. Empty batteries must be handed in for required liquidation, e.g. to the Kamstrup Company.
10 6.2 Main voltage modules Modules belong to the safety class ll, and are connected with a double-wire conductor (without grounding) through the calculator cable grommet; the calculator is placed to the right from the connection base. Use a 5 to 10 mm outer diameter connecting cable, and secure proper disassembly and assembly of the voltage cable releaser. Max. fuse allowed: 6 A Assembly regulations must be followed during the assembly. 24 VAC 230 VAC For example, a 230/24 V transformer, This module is used for direct type can be used. connection to the electric network. NOTE! MULTICAL 601 cannot be supplied from a 24 VDC. 7. Function test After completion of the electric meter assembly, check its functionality. Activate water flow through the heating system, by opening heat regulators and taps. Press top MULTICAL 601 button, and verify the temperature and water flow figures on the display.
11 8. Electric connection The polarity of T1, T2 and T3 temperature sensors is not important. When connecting ULTRAFLOW and electronic sensor units, use the colours given for V1 and V2 flow meters. Flow meters with Reed-contact output need to be connected to clips 11-10, or V1 V Blue Red SIG Yellow Clip number Standard heat and cold measurements Heat measurement and leak records T1 5-6 Sensor in supply piping (red) Sensor in supply piping (red) T2 7-8 Sensor in return piping Sensor in return (blue) piping (blue) V Flow meter in supply or Flow meter in supply return piping piping V Flow meter in return piping T Container/heat exchanger temperature Energy measurement in open systems Sensor in supply piping (red) Sensor in return piping (blue) Flow meter in supply piping Flow meter in return piping Reference sensor (grey) 9. Insert modules MULTICAL 601 can be extended with a range of functions, using the insert modules. Individual modules are briefly described below. 9.1 Data/impulse inputs Data outputs are used, for example, for computer connection. The signal is passive and galvanic ally separated using opto-electric coupling elements. Transmission to RS232 level requires a connection of data cable (D-Sub 9F) or (USB), through the following connection: 62 Brown (DAT) 63 White (REQ) 64 Green (GND)
12 NOTE! If data reading is to be compatible with MULTICAL 66-CDE, a top module needs to be used in MULTICAL 601. Impulse inputs can be used for connecting both electric and water meters. Please, bear in mind the maximum impulse frequency and correct impulse codes (l/impulse and Wh/impulse), which are selected in FF and GG configuration Input A Input B 9.2 M-Bus, type /08/20 M-Bus can be connected into a star-shape, ring, or bus line. According to the M-Bus Master supply, and total cabling resistance, up tpo 250 meters can be connected. Cable resistance Cable capacity < 29 Ohm < 180 nf M-Bus network is connected to clips 24 and 25. The polarity is not important. M-Bus is supplied with impulse inputs. of NOTE! /08 requires the installation top module. 9.3 Radio/impulse inputs, type A/0B/25/26 The radio module is used for wireless communication over a licence-free radio frequency; it is available for both interior and exterior antennas. Further information on the radio module are given in Radio technical description ( ). Impulse inputs of this module are identical with the above mentioned modules. NOTE! A/0B requires the installation of top module. Type includes radio and router functions.
13 9.4 Analogue output Type , see Assembly guide (DK-GB-DE). 9.5 Lon Works Type , see Assembly manual (DK) or (GB). 9.6 Top modules Type 67-01: RTC (Real Time Clock) The top module consists of real time clock and backup battery. When the MULTICAL 601 is placed in the supply console, and the voltage is low, current date and time are transferred from the top module into the calculator. Top module is recommended for applications which need to have the correct date/time in permanent memory, as well as time controlled tariffs. The real time clock and backup battery represent standard equipment of all other top modules. This module does not use screws. Type 67-02: RTC + Energy + Hourly data recorder This top module counts the differences between heat energy in both supply and return piping, and hot supply water energy in open systems. This module also consists of an hourly data recorder. This module does not use screws. Type 67-06: RTC + compatibility with 66-C + 2 impulse outputs (CE and CV) Top module secures MULTICAL 601 compatibility with MULTICAL 66-C, which allows using most original basic modules for MULTICAL 66-C in the MULTICAL 601. Moreover, the top module has two independent impulse outputs for energy (CE) and capacity (CV). Impulse resolution reflects display data (defined by CCC-code). E.g.: CCC=119 (qp 1.5): 1 impulse/kwh and 1 impulse/0.01 m3. Impulse outputs are optically isolated, and have 30 VDC and 10 ma.
14 Type 67-07: RTC + M-Bus An M-Bus can be connected into a star, ring, or bus line. According to M-Bus Master supply and cable length/diameter, up to 250 meters with primary addressing can be connected; even more can be connected if secondary addressing is used. Network conductor resistance: < 29 Ohm Network conductor capacity: < 180 nf Polarity of clips 24 and 25 connection is not important. Primary addresses usually consist of the last numbers in a customer number ( ),and can be changed using METERTOOL software. Type 67-08: RTC + hourly data recorder + impulse outputs This top module has two impulse outputs for capacity and energy, which can be freely configured. They are suitable for capacity and energy impulses for heat, cold, or combined meters. Impulse resolution reflects display data (defined by CCC-code). E.g.: CCC=119 (qp 1.5): 1 impulse/kwh and 1 impulse/0.01 m 3. Impulse outputs are optically isolated, and have 30 VDC and 10 ma. Energy (CE) is usually connected to clip 16-17; capacity (CV) is then connected to clip However, other combinations can be selected using METERTOOL software, which is also used to select the impulse duration 32 or 100 ms. Moreover, this module also includes an hourly data recorder. Type 67-09: RTC + capacity + hourly data recorder This top module counts the difference between heat energy in supply and return piping, and hot supply water energy in open systems. Figure difference dv=v1-v2. This module also includes an hourly data recorder. This module does not use screws.
15
16
How To Use A Multi-Line Calculator With A Power Supply And Power Supply (Kamstrup)
Installation and User s Guide MULTICAL 601 & ULTRAFLOW 14 Cooling meter www.kamstrup.com Operation conditions Operation conditions/measuring ranges: Calculator θ: 2 C 180 C Θ: 3K 170K Temperature sensor
More informationMULTICAL 602 & ULTRAFLOW 14
Installation and User Guide MULTICAL 602 & ULTRAFLOW 14 Cooling meter www.kamstrup.com 1 Operation conditions Operation conditions/measuring ranges: Calculator q: 2 C 180 C DΘ: 3K 170K Temperature sensor
More informationSHARKY 775 COMPACT ENERGY METER ULTRASONIC
APPLICATION The ultrasonic compact energy meter can be used for measuring the energy consumption in heating / cooling application for billing purposes. FEATURES 4 Approval for ultrasonic meter with dynamic
More informationCORONA E / FLYPPER ELECTRONIC METER MULTI-JET
APPLICATION Fully electronic compact water meter with impeller scanning for recording volume. Highly accurate recording of all billing data at medium temperatures up to 90 C. FEATURES 4 Electronic sensor
More informationInstallation and User Guide for MULTICAL 62. Water meter. www.kamstrup.com
Installation and User Guide for MULTICAL 62 Water meter www.kamstrup.com 123456 MULTICAL 62 Water meter English installation Kamstrup A/S Industrivej 28, Stilling, DK-8660 Skanderborg Tel: +45 89 93 10
More informationMOUNTING AND OPERATING INSTRUCTIONS
MOUNTING AND OPERATING INSTRUCTIONS CF 51/55 1. Delivery CF 51/55-1 calculator with battery (optionally with mains power supply) - 1 wall mounting bracket - package with material for sealing, screws, wall
More informationHYDRUS ULTRASONIC METER
HYDRUS APPLICATION HYDRUS is a static water meter based on the ultrasonic technology. This technology enables accurate calculation of water consumption and eliminates measuring deviations caused by sand,
More informationSHARKY 775 COMPACT ENERGY METER ULTRASONIC
APPLICATION The ultrasonic compact energy meter can be used for measuring the energy consumption in heating / cooling application for billing purposes. FEATURES 4 Approval for ultrasonic meter with dynamic
More informationMULTICAL 602 DATA SHEET
Complete range of communication modules High Power RadioRouter module Data loggers Info loggers Data backup in case of power failure EN 1434 MID-2004/22/EC M12 0200 Heat and cooling meters with unlimited
More informationT0118 T2118 T3118. Instruction Manual
Programmable indoor transmitter of temperature T0118 Programmable indoor transmitter of atmospheric pressure T2118 Programmable indoor transmitter of temperature, relative humidity and other derived humidity
More informationToroidal Conductivity Sensor
Instruction Sheet PN 51A-/rev.C June 2012 Toroidal Conductivity Sensor For additional information, please visit our website at www.emersonprocess.com/rosemountanalytical.com SPECIFICATIONS Wetted Materials:
More informationMULTICAL 21 DATA SHEET. Electronic ultrasonic cold and hot water meter
Ultrasonic measurement Pinpoint accuracy Longevity Vacuum sealed construction Environment-friendly meter MID-2004/22/EC M12 0200 Electronic ultrasonic cold and hot water meter MULTICAL 21 is used for measurement
More informationDigital inductive conductivity transmitter
Digital inductive conductivity transmitter Optimal solution for conductivity measurements in difficult fluids (polluted, dirty,...) PEEK/PPA version for CIP applications Large range of process connections
More informationPD30ETB20xxIS. Photoelectrics, Background Suppression reflective with IR light. Main features. Description
Photoelectrics, Background Suppression reflective with IR light Main features Description The PD30ET... stainless steel sensors are built with high-quality materials and designed for harsh environments.
More informationAnalogue Input, 4-fold, MDRC AE/S 4.1, GH Q605 0054 R0001
Analogue Input, -fold, MDRC, GH Q605 005 R0001 The analogue input is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via the bus connecting terminal supplied.
More informationHERZ-Thermal Actuators
HERZ-Thermal Actuators Data Sheet 7708-7990, Issue 1011 Dimensions in mm 1 7710 00 1 7710 01 1 7711 18 1 7710 80 1 7710 81 1 7711 80 1 7711 81 1 7990 00 1 7980 00 1 7708 11 1 7708 10 1 7708 23 1 7709 01
More informationHow To Use A Flowmeter
INLINE flowmeter for continuous flow measurement Economic integration in pipe systems without any additional piping 3-wire frequency pulse version to directly interface with PLC s (both PNP and NPN) Connection
More informationLaserlyte-Flex Alignment System
Laserlyte-Flex Alignment System LaserLyte-Flex The LaserLyte-Flex Alignment System is a unique, interchangeable, low cost plug and play laser system. Designed specifically for aligning and positioning
More informationOutdoor 33.6W Dual Port Passive Power-over-Ethernet Midspan For External Security Cameras and Wireless Access Points
Outdoor 33.6W Dual Port Passive Power-over-Ethernet Midspan For External Security Cameras and Wireless Access Points Features SELV Compliant No Detection Passive Injector Gigabit Compatible Full Protection
More informationCONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version)
TECHNICAL DATASHEET #TD1102AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version) Part Number: Connector Amplifier CAPV-H-4-20MA-x complete with cable CAPV-4C-yM Where: x = current output
More informationVroom Hardware manual ver. 1.00 Code 114VROOHWE00. Vroom CANBUS USER INTERFACE WITH LCD GRAPHIC DISPLAY AND WITH TEMPERATURE AND HUMIDITY SENSOR
Vroom CANBUS USER INTERFACE WITH LCD GRAPHIC DISPLAY AND WITH TEMPERATURE AND HUMIDITY SENSOR ENGLISH HARDWARE MANUAL ver. 1.00 CODE 114VROOHWE00 page 1 of 22 Important Important Read these instructions
More informationGivare NC-SRS 280 och 880
Givare NC-SRS 280 och 880 Aratron AB/Nordic Control, 02 03 SRS280SEALED ROTARY SENSOR PERFORMANCE ±2 Resistance ±20% Hysteresis (repeatability) Accuracy Applied voltage maximum Resolution Output smoothness
More informationA99B Series Temperature Sensors
FANs 125, 121, 930, 930.5 Product/Technical Bulletin A99 Issue Date 0615 A99B Series Temperature s The A99B Series Temperature s are passive PTC (Positive Temperature Coefficient) sensors. The A99B sensors
More informationBM SERIES WAVE COMPACT 6.3 GHZ CW SERIES PULSE RADAR LEVEL INSTRUMENTS (6.3 GHz)
CW SERIES PULSE RADAR LEVEL INSTRUMENTS (6.3 GHz) DESCRIPTION The Radar Level Meters of BM COMPACT WAVE 6.3 GHz series are excellent devices for no contact level measurement. The microwave impulses, emitted
More informationMILLENIUM INSTALLATION MANUAL NTR 735 A. Simple Automation Control Module (MAS)
MILLENIUM Table of contents 1. INTRODUCTION 1 2. HARDWARE DESCRIPTION 2 3. INSTALLATION 5 4. CONNECTION 6 5. USER SAFETY AND PROTECTION OF EQUIPMENT 8 1. Introduction The MILLENIUM series has been designed
More informationInstructions Manual. Electromagnetic sensor Series FLOMID FX. instrumentation for fluids. R-MI-FlomidFX Rev.: 0 English version
instrumentation for fluids Electromagnetic sensor Series FLOMID FX Instructions Manual! Conforms with the Pressure Equipment Directive 97/23/EC. 0830 This equipment is considered as being a pressure accessory
More informationRotary actuators Rotary wing drives Series RAK. Brochure
Brochure 2 Rotary wing drives, angle of rotation: 30-270 Rotary wing drive, double-acting axis geometry: single 4 Rotary wing drives, angle of rotation: 90-270 Rotary wing drive, double-acting axis geometry:
More informationCross-beam scanning system to detect slim objects. 100 mm 3.937 in
891 Object Area Sensor General terms and conditions... F-17 Related Information Glossary of terms... P.1359~ Sensor selection guide...p.831~ General precautions... P.1405 PHOTO PHOTO Conforming to EMC
More informationZlinx Wireless I/O. Peer-to-Peer and Modbus I/O B&B ELECTRONICS PRODUCT INFORMATION
Modular, Customizable Wire Replacement 128 / 256 Bit AES Encryption Software Selectable RF Transmit Power Software Selectable Over-the-air Data Rate Modbus ASCII /RTU Compatible Wide Operating Temperature
More informationQR12 (1.22 ) Diameter Optical Encoder
Improving the Quality of Life through the Power in Light QPhase QR12 (1.22 ) Diameter Optical Encoder Design Features: Low profile assembled height of Bearing design simplifies encoder attachment Resolutions
More informationJNIOR. Overview. Get Connected. Get Results. JNIOR Model 310. JNIOR Model 312. JNIOR Model 314. JNIOR Model 410
The INTEG is an Ethernet I/O (digital, analog) device that monitors and controls a small set of process signals. functions as both basic I/O for integration with another application or system AND as a
More informationCable Plug acc. to DIN EN 175301-803, Form A
Cable Plug acc. to DIN EN 175301-803, Form A Complete program Contact form 18 mm Also available with LED indicator Optional 4-pin version for pressure switch or impulse valves respectively Versions with
More informationSONOMETER TM 1000 Ultrasonic compact heat meter
Data sheet SONOMETER TM 000 Ultrasonic compact heat meter Description/Application MID examination certificate no. : DE-07-MI004-PTB02 The SONOMETER 000 is an ultrasonic static compact heat meter especially
More informationInstruction Manual. T3111 T3111L T3111P T3111Ex
www.cometsystem.cz Instruction Manual T3111 T3111L T3111P T3111Ex Programmable transmitter of temperature, relative humidity and other calculated humidity values with external probe and 4-20 ma outputs
More informationLED...A70..4-..Q Series Sealed High-Intensity
LED...A70..4-..Q Series Sealed High-Intensity Area Lights High-Power Lighting for use with PresencePLUS and Other Vision Systems Features Rugged, waterproof housing, rated IEC IP68 Compact area light for
More informationTurbine Flow Sensor Series VTR
Turbine Flow Sensor Series VTR SIKA Turbine Flow Sensor Series VTR Extra robust, impressively precise SIKA s VTR turbine flow sensor allows you to determine precisely, dependably and easily the flow rates
More informationMaterial: Weight: Bearing Life: Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads:
Automation / Mini Type SCH32F Hollow Shaft Encoder - Ø 32 mm Hollow Bore: Ø 6 mm to Ø 3/8 inch Resolution up to 5000 ppr IP 65 (IP 50 for IDC connector option) Electrical Specifications Code: Resolution:
More informationHG600/HG800. Hydro-Power Unit. Installation and Operation Guide
HG600/HG800 Hydro-Power Unit Installation and Operation Guide Copyright 04 HydroSpin, All rights reserved. The data contained in this document is proprietary to HydroSpin. It is disclosed to the receiving
More informationArt.S001-S002 SOLAR MODULE WITH DELIVERY AND RETURN CONNECTIONS
Art.S001-S002 SOLAR MODULE WITH DELIVERY AND RETURN CONNECTIONS Technical Information sheet 0001/07/Rev01 ENG FUNCTION Series S001 and S002 circulation units are applied to the primary circuit of solar
More informationINSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930
INSTALLATION GUIDE Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 Card Reader and Controller Model 3.5 with KIM Swipe Reader Table of Contents 1. Features..................................
More informationThe multi-functional integrator Supercal 531
The multi-functional integrator Supercal 531 Design The Supercal 531 integrator is suitable for connecting Pt 500 or Pt 100 temperature sensor pairs with 2 or 4-conducting wire techniques. Volume inputs
More informationDuct Humidity Transmitter
SDC-H Duct Humidity Transmitter Features Replaceable sensor element Humidity measurement for air ducts Minimum and maximum value memory 0 0V, 0 0mA or 0V, 4 0mA measuring signals selectable with jumpers
More informationDiwiTherm, Resistance Thermometers Model TR75, with digital Display Battery or Solar Powered
Electrical Temperature Measurement DiwiTherm, Resistance Thermometers Model TR75, with digital Display Battery or Solar Powered WIKA Data Sheet TE 60.75 Applications Machinery, plant and tank construction
More informationArecont Vision H.264 Color or Day/Night SurroundVideo Series Installation Manual
0 P a g e H.264 Color or Day/Night SurroundVideo Installation Manual Inside the box: A. Arecont Vision SurroundVideo camera B. Mounting template C. RJ45 female to female coupler D. Hex key E. Security
More informationLMU-5000. Hardware and Installation Guide
LMU-5000 Hardware and Installation Guide Plan The Installation Verify Power, Ground and Ignition. Be sure to check each source (power, ground and ignition) to ensure that the proper signaling exists. This
More informationPSU-U-24V/AC-6A/10/FTA-TR-MC PSAC 0624
PSU-U-24V/AC-6A/10/FTA-TR-MC PSAC 0624 v.1.0 AC/AC power supply unit Edition: 1 from 24 th October 2008 Supercedes edition: ---------- 10062009 CONTENTS: 1. Technical description. 1.1. General description
More informationATL Fuel Level Sender Probes
T E C H N I C A L S P E C I F I C A T I O N The ATL EL-AD-151 (Resistance Output) and EL-AD-152 (Voltage Output) Fuel Level Senders are highly advanced sensors for continuously measuring the contents of
More informationUSER GUIDE. Studio Hotline Multi-line System Phone Flasher and Door/Alert Indicator Input Module and Indicator. DM Engineering. Version 1.
USER GUIDE Studio Hotline Multi-line System Phone Flasher and Door/Alert Indicator Input Module and Indicator Version 1.3 DM Engineering 2174 Chandler St. Camarillo, CA 91345-4611 805-987-7881 800-249-0487
More informationIFC 070 Technical Datasheet
IFC 070 Technical Datasheet Electromagnetic signal converter Battery driven with low energy consumption Quick and easy to install and operate External data logger and GSM module for remote data transfer
More informationSENSORS. Miniature Sensors - S3Z. Advanced line of miniature Asian style of photoelectric sensors. 40-300 mm background suppression
Advanced line of miniature Asian style of photoelectric sensors 4-3 background suppression.7 m proximity, 15 with narrow beam 4 m polarized retroreflective 3 m LASER through beam Standard 3-wire output
More informationOPL BASIC. Dosing System for Professional Laundry machines. Contents
OPL BASIC Dosing System for Professional Laundry machines Contents 1 Getting Started. Page 2 2 Installation. Page 4 3 Set Up & Operation. Page 8 4 Maintenance & Accessories. Page 10 5 Troubleshooting Page
More informationHow To Power A Schen
Automation / Mini Type SCH32F Hollow Shaft Encoder - Ø 32 mm Hollow Bore: Ø 6 mm to Ø 3/8 inch Resolution up to 5000 ppr IP 65 (IP 50 for IDC connector option) Electrical Specifications Code: Resolution:
More informationModel 201 Wiegand Touchpad Reader Installation Guide
Model 201 Wiegand Touchpad Reader Installation Guide P/N 460353001C 15AUG11 2011 UTC Fire & Security. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without
More informationUSB-ISS-UV/VIS Integrated Sampling System Installation and Operation Instructions
USB-ISS-UV/VIS Integrated Sampling System Installation and Operation Instructions Description The USB-ISS-UV/VIS Integrated Sampling System is a snap-on, direct-attach 1 cm cuvette holder and UV/VIS/NIR
More informationFLOAT SWITCHES FLOW SWITCHES FOR LIQUIDS PRESSURE SWITCHES
01D351-GB FLOAT SWITCHES FLOW SWITCHES FOR LIQUIDS PRESSURE SWITCHES DOLOMIT FLOAT SWITCHES The DOLOMIT float switches find application in liquid level control in tanks and wells; they require connection
More informationInstruction book IQAN-MDM. Publ. no. HY17-8328/UK Edition June, 2007
Instruction book IQAN-MDM Publ. no. HY17-8328/UK Edition June, 2007 Contents 1 Introduction...............................................................3 Safety symbols................................................................
More informationTypical Aluminum GFM Mass Flow Meter
MASS FLOW METERS Design Features n Rigid metallic construction. n Maximum pressure of 1000 psig (70 bars). n Leak integrity 1 x 10-9 of helium. n NIST traceable certification. n Built-in tiltable LCD readout.
More informationDRTS 33. The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters
The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationphotoelectric highlights www.automation.datalogic.com
photoelectric miniature sensors S8 series The new S8 series of compact sensors offers excellent detection performances, usually associated with sensors that have larger dimensions and a higher price. The
More information3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
More information33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3at Standard -40 to +60 C Temperature Range Diagnostic LEDs Full Protection
More informationProcess modules Digital input PMI for 24 V DC inputs for 120 V AC inputs
E031026 000823 Process modules Digital input PMI for inputs for 120 V AC inputs PMI Input E4, E5, GND L- PMI 120 V AC Input E4, E5, Common C E6, E7, GND L- E6, E7, Common C LEDs for the inputs operation
More informationSHARKY 775 Ultrasonic Compact Energy Meter. Installation and User Guide
SHARKY 775 Ultrasonic Compact Energy Meter Installation and User Guide for software version F01-001 1 Contents 1 General... 4 1.1 About this Installation and User Guide... 4 1.1.1 Target groups...4 1.1.2
More informationDirectory chapter 04
M Directory chapter 04 D-Sub Mixed subminiature D connectors New Page D-Sub mixed connector system general information................... 04.02 Contact arrangements............................................
More informationAutoLink Three-Phase Sectionalizer Specifications. Scope. General. Applicable Standards. Operating principle
Scope This specification stipulates the minimum requirements for mechanically linked three-phase electronic sectionalizers, for use on outdoor medium voltage overhead lines of 15, 27, and 38 kv. Electronic
More informationClear Glass Sensor. Ordering Information E3S-CR67/62. Optimum Sensor for Detecting Transparent Glass and Plastic Bottles
Clear Glass Sensor Optimum Sensor for Detecting Transparent Glass and Plastic Bottles E3S-CR67/62 Retroreflective Sensor smoothly detects 5-mm gaps. Detects transparent bottles that have a lens effect.
More informationMax primary circuit temperature 90ºC Max primary circuit temp. 90ºC Max secondary circuit temperature 45ºC Max secondary circuit temp.
EGLISH 1 Product description exchanger equipped with an electronic control unit and circulation pump for the primary circuit. All Aqua-Mex variants can be ordered with an interior coil of either titanium
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationMagnetic and Hydraulic-Magnetic Circuit Breaker 8340-G2...
Magnetic and Hydraulic-Magnetic Circuit Breaker 840-G2... Description Single, two and three pole magnetic circuit breakers with trip-free mechanism and push/pull on/off manual actuation. A choice of fast
More informationElectronic Pressure Switch EDS 300
Electronic Pressure Switch EDS 300 User manual Page 2 of 16 Content 1. Functions of the EDS 300...3 2. Mounting...3 3. Operating keys on the membrane keypad...4 4. Digital display...4 5. Output function...5
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)
17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure
More informationDrayton Digistat +2RF/+3RF
/+3RF Programmable Room Thermostat Wireless Model: RF700/22090 Model: RF701/22092 Power Supply: Battery - Thermostat Mains - Digistat SCR Invensys Controls Europe Customer Service Tel: 0845 130 5522 Customer
More informationQuick Connect. quick - simple - efficient. www.g-mw.de
Quick Connect quick - simple - efficient www.g-mw.de Phone: +49 9103 7129-0 Fax: +49 9103 7129-207 Innovative connection technology to plug three single-phase current transformers to multifunctional power
More informationQFP910. Water detector. Building Technologies. CE1N2732en 2016-03-01. Synco living
2 732 Synco living Water detector QFP910 Wireless radio sensor to record water puddles RF communication based on KNX standard (868 MHz unidirectional) Battery operation with standard 1.5 V batteries Use
More informationHow To Control A Power Supply With A Mini Transmitter And Switch (Power Supply)
transmitter (2 wire) / switch for continuous or On/Off Control Indication, monitoring, transmitting and continuous or On/Off control in one device Output signal 4...20 ma, 2-wire for continuous control
More informationHMI display Installation Guide
HMI display Installation Guide Product Description Specifications Important Information o Package Contents o Related Documents o Accessories Cautions and Warnings Mounting and Dimensions o BAC-DIS-ENC
More informationSubmersion/Insertion Toroidal Sensor
Instruction Sheet PN 51A-228/rev.P December 2010 Model 228 Submersion/Insertion Toroidal Sensor For additional information, please visit our website at www.emersonprocess.com/raihome/liquid/. CAUTION SENSOR/PROCESS
More informationService Guide 12/27/03 TESTING, SERVICE & REPAIR GUIDE (For SH Space Heating Models & RA Water Heating Models)
TESTING, SERVICE & REPAIR GUIDE (For SH Space Heating Models & RA Water Heating Models) WARNING - HIGH VOLTAGE AC electrical circuits are connected to this heater. Do not attempt any service work on the
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationPSACH 01246 v.1.0 PSACH 24VAC/6A/1x6A HERMETIC AC power supply for CCTV
PSACH 01246 v.1.0 PSACH 24VAC/6A/1x6A HERMETIC AC power supply for CCTV EN Edition: 2 from 12.12.2013 Supersedes the edition: 1 from 18.06.2013 Features: power output 24V AC/6A or 27V AC/ 5,5A power voltage
More informationAutomotive Sensor Simulator. Automotive sensor simulator. Operating manual. AutoSim
Automotive sensor simulator Operating manual AutoSim Contents Introduction.. page 3 Technical specifications.... page 4 Typical application of AutoSim simulator..... page 4 Device appearance... page 5
More informationPPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES BUSHING WITH PLUG CONNECTION WITH OUTER CONE PPS CHARACTERISTICS The PPS bushing can be used as a fixed section for the entry of medium
More informationElectronic pressure switch with display Model PSD-30, standard version Model PSD-31, with flush diaphragm
Electronic pressure measurement Electronic pressure switch with display Model PSD-30, standard version Model PSD-31, with flush diaphragm WIKA data sheet PE 81.67 Applications Machine tools Hydraulics
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More information12 Volt 30 Amp Digital Solar Charge Controller
12 Volt 30 Amp Digital Solar Charge Controller User s Manual WARNING Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationINPUT/OUTPUT MODULE CONVERT INPUTS AND OUTPUTS TO WIRELESS
VMC A4 INPUT/OUTPUT MODULE CONVERT INPUTS AND OUTPUTS TO WIRELESS PRODUCT DATA SHEET FEATURES RF to 0-10 VDC out, analogue or PWM Maximal 3 digital inputs to RF RF communication with other equipment Wireless
More informationM-Bus. Technical Description
M-Bus Technical Description Kamstrup A/S Industrivej 28, Stilling DK-8660 Skanderborg TEL: +45 89 93 10 00 FAX: +45 89 93 10 01 E-MAIL: energi@kamstrup.dk WEB: www.kamstrup.com 2 Contents 1. Technical
More informationModular I/O System Analog and Digital Interface Modules
OPERATING INSTRUCTIONS Modular I/O System Analog and Digital Interface Modules Installation Operation Maintenance Document Information Document ID Title: Operating Instructions Modular I/O System Part
More informationInstallation Guide. WSD-100 Wind Speed and Direction Sensor For XR5 Data Loggers. February, 2011
WSD-100 Wind Speed and Direction Sensor For XR5 Data Loggers Installation Guide February, 2011 Pace Scientific Inc www.pace-sci.com Tel: 704-799-0688 sales@pace-sci.com 1 Disclaimer The following warranty
More informationDTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual
DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8
More informationThreaded Resistance Thermometers Model TR10-D, Miniature Design
Electrical Temperature Measurement Threaded Resistance Thermometers Model TR10-D, Miniature Design WIKA Data Sheet TE 60.04 Applications Machine building, plant and tank construction Power transmission
More informationInstruction Sheet ACS-101. General Description. Specifications. Amplified Broadband UHF Combiner-Splitter. Overall. Antenna Splitter.
ACS-101 Amplified Broadband UHF Combiner-Splitter General Description The ACS-101 (Antenna Combiner Splitter 10 to 1) is an amplified and filtered broadband splitter-combiner. It allows up to 10 base stations
More informationProgrammable set for Ethernet Modbus/TCP in IP67 TI-BL67-PG-EN-2
Type code Ident no. 1545065 Number of channels 2 Dimensions (W x L x H) 108 x 145 x 77.5 mm CoDeSys-programmable acc. to IEC 61131-3 Cable max. 50 m between interface and read/write head 10/100 Mbps Male
More informationWireless Indoor/ Outdoor Thermometer
Wireless Indoor/ Outdoor Thermometer Owner s Manual Please read before using this equipment. ˆ Contents FCC Information... 3 FCC Declaration of Conformity... 5 Preparation... 5 Installing Batteries...
More informationInstallation and Operation Manual. Digital Remote Meter for Monitoring System Performance. Version: RM-1
REMOTE METER TM Installation and Operation Manual. Digital Remote Meter for Monitoring System Performance. Version: RM-1 1098 Washington Crossing Road Washington Crossing, PA 18977 USA www.morningstarcorp.com
More informationUSER MANUAL V5.0 ST100
GPS Vehicle Tracker USER MANUAL V5.0 ST100 Updated on 15 September 2009-1 - Contents 1 Product Overview 3 2 For Your Safety 3 3 ST100 Parameters 3 4 Getting Started 4 4.1 Hardware and Accessories 4 4.2
More informationD7050/D7050TH. Installation Instructions. Multiplex Photoelectric Smoke Detectors
D7050/D7050TH EN Installation Instructions Multiplex Photoelectric Smoke Detectors D7050/D7050TH Installation Instructions.0 Description Notices These instructions cover the installation of the D7050/D7050TH
More informationProduct and Applications Description. Application Programs. Example of Operation. GAMMA instabus Technical Product-Information.
Product and Applications Description The power supply units N 125/x2 can supply DC 24 V power from an additional pair of terminals (yellowwhite). This DC 24 V output voltage can be used to power e.g. an
More informationReplacement parts. WM97+ gas-fired water boiler Boiler Manual. OBTAIN PARTS ONLY THROUGH WEIL-McLAIN THE BOILER CONTAINS CERAMIC FIBER MATERIALS
Replacement parts DO NOT SERVICE THE BOILER WITHOUT A WM97+ MAINTENANCE KIT AVAILABLE Failure to adhere to these guidelines can result in severe personal injury, death or substantial property damage. The
More informationPK-01. Standalone door control module. SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00
Standalone door control module PK-01 Firmware version 1.00 pk-01_en 06/12 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.eu WARNINGS Read carefully
More information