Characteristics Values Units. Rectangular waveform 0.5 A. range - 55 to 150 C

Transcription

1 Bulletin I075 rev. C 05/06 IR0530CSPTRPbF 0.5 Amp 30 Volt Features Ultra Low V F To Footprint Area Very Low Profile (<0.6mm) Low Thermal Resistance Supplied Tested And On Tape & Reel Lead-Free ("PbF" suffix) Applications Reverse Polarity Protection Current Steering Freewheeling Flyback Oring Major Ratings and Characteristics Characteristics Values Units I F(AV) Rectangular waveform 0.5 A V RRM 30 V I tp = 5 μs sine 90 A V 0.5 Apk, T =25 C 0.33 V T range - 55 to 50 C Description International Rectifier's FlipKY product family utilizes wafer level chip scale packaging to deliver Schottky diodes with the lowest V F to PCB footprint area in industry. The three pad 0.9mm x.2mm devices can deliver up to 0.5A and occupy only.08mm 2 of board space. The anode and cathode connections are made through solder bump pads on one side of the silicon rather than through protruding leads enabling designers to strategically place the diodes on the PCB. This design not only minimizes board space but also reduces thermal resistance and inductance, which can improve overall circuit efficiency. Typical applications include hand-held, portable equipment such as cell phones, MP3 players, PDAs, and portable hard disk drives where space savings and performance are crucial.

2 Bulletin I075 rev. C 05/06 Voltage Ratings V R Part number Max. DC Reverse Voltage V RWM Max. Working Peak Reverse Voltage IR0530CSPTRPbF 30 Absolute Maximum Ratings Parameters Value Units Conditions I F(AV) Max. Average Forward Current 0.5 A 50% duty T PCB = 33 C, rectangular wave form I FSM Max. Peak One Cycle Non-Repetitive 90 A 5μs Sine or 3μs Rect. pulse Surge 25 C 0 0ms Sine or 6ms Rect. pulse Following any rated load condition and with rated V RRM applied E AS Non- Repetitive Avalanche Energy 5 m T = 25 C, I AS = 2.0A, L = 5.0mH I AR Repetitive Avalanche Current 0.5 A Current decaying linearly to zero in μsec Frequency limited by T max. Va =.5 x Vr typical Electrical Specifications Parameters Typ. Max. Units Conditions V FM Max. Forward Voltage () A T = 25 C Drop 0.45 A * See Fig A T = 25 C 0.36 A I RM Max. Reverse Leakage () 0 50 μa T = 25 C V R = rated V R Current * See Fig ma T = 25 C C T Max. unction Capacitance - 90 pf V R = 5V DC (test signal range 00kHz to MHz) 25 C dv/dt Max. Volatge Rate of Charge V/ μs (Rated V R ) Thermal-Mechanical Specifications Parameters Value Units Conditions T Max. unction Temperature Range (*) - 55 to 50 C T stg Max. Storage Temperature Range - 55 to 50 C R thl Typ. Thermal Resistance unction 35 C/W DC operation to PCB (**) R tha Max. Thermal Resistance unction 50 C/W to Ambient (**) (*) dptot < thermal runaway condition for a diode on its own heatsink dtj Rth( j-a) (**) Mounted on dual sided 0.58 inch square FR4 PCB with 0.2 square inches of oz top copper area 2

3 Bulletin I075 rev. C 05/ Reverse Current - I R (ma) Tj = 50 C 25 C 00 C 75 C 50 C 25 C Instantaneous Forward Current - I F T = 50 C T = 25 C T = 25 C Forward Voltage Drop - V FM Fig. - Max. Forward Voltage Drop Characteristics (Per Leg) unction Capacitance - C T (p F) Reverse Voltage - V R Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg) T = 25 C Reverse Voltage - V R Fig. 3 - Typical unction Capacitance Vs. Reverse Voltage (Per Leg) 3

4 Bulletin I075 rev. C 05/06 Allowable Case Temperature ( C) Square wave (D = 0.50) 80% Vr applied see note (2) D = 3/4 D = /2 D = /3 D = /4 D = /5 DC Average Power Loss (Watts) D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 RMS Limit DC Average Forward Current - I F(AV) Average Forward Current - I F(AV) Fig. 4 - Max. Allowable Case Temperature Vs. Average Forward Current (Per Leg) Non-Repetitive Surge Current - I FSM At Any Rated Load Condition And With Rated Vrrm Applied Following Surge Square Wave Pulse Duration - t p (microsec) Fig. 6 - Max. Non-Repetitive Surge Current (Per Leg) L Fig. 5 - Forward Power Loss Characteristics (Per Leg) DUT IRFP460 HIGH-SPEED SWITCH Rg = 25 ohm FREE-WHEEL DIODE + Vd = 25 Volt CURRENT MONITOR 40HFL40S02 Fig. 8 - Unclamped Inductive Test Circuit (2) Formula used: T C = T - (Pd + Pd REV ) x R thc ; Pd = Forward Power Loss = I F(AV) x V (I F(AV) / D) (see Fig. 6); Pd REV = Inverse Power Loss = V R x I R ( - D); I 80% V R applied 4

5 Bulletin I075 rev. C 05/06 Outline Dimension and Tape and Reel ASSIGNMENTS = CATHODE 2 = CATHODE 3 = ANODE NOTES:. DIMENSIONING & TOLERANCING PER ASME Y4.5M CONTROLLING DIMENSION: MILLIMETER 3. DIMENSIONS ARE SHOWN IN MILLIMETERS BALL LOCATION MARK PART NUMBER D 0 23 WORKWEEK (Y, WW) LOT NUMBER Ø 3" RECOMMENDED FOOTPRINT 8mm A BALL LOCATION Pin 2 Cathode Pin Cathode 8mm mm FEED DIRECTION NOTES: Pin 3 Anode. TAPE AND REEL OUTLINE CONFORMS TO EIA-48 & EIA Special Instruction for PCB assembly: see APPLICATION NOTE AN-079 Data and specifications subject to change without notice. This product has been designed for Consumer Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (30) TAC Fax: (30) Visit us at for sales contact information. 05/06 5