Mains. Assembly SCCRs. Voltage ratings. Bus amperages. Branch circuits. Panels. Through-lugs & loadside disconnect. Neutrals. Grounds.

Transcription

1 Quik-Spec oordination Panelboard Specifications 11 PELORDS QuikShip ll SQSP configurations of the standard EM 1 enclosure can be specified for shipment within 10 business days of order when specified. Mains MLO (Main Lug Only) Fused disconnect switch on-fused disconnect switch ssembly SRs Voltage ratings us amperages ranch circuits Panels Through-lugs & loadside disconnect eutrals Grounds Enclosure sizes Spare fuses Options 200k, 100k or 50k, 100k or 20k@125Vdc pplicable on any 600Vac or less, or 125Vdc or less systems 400, 225, 200, 100, 60 or 30 ircuits: 18, 30 or 42* mps: Up to 100 Type: 1-, 2- and 3-Pole Feed: top & bottom Mounting: surface or flush Door/Trim: regular or door-in-door EM Ratings: 1 & 3R. Other ratings available, consult factory. Feed-Through: single and double Sub-Feed Feed/Sub-Through Fused loadside disconnect, (up to 1/2 of main amp rating) 200, 400 and 800 unbonded and bonded on-isolated or isolated Standard size panelboard (20 W x 5¾ D x H)* Spare fuse compartment holds up to six fuses Surge protection device (TVSS) for high and low energy transients. Depending on configuration. 125Vdc rating applicable to only 40 amp or less Ps on MLO panels only Siemens Industry, Inc. SPEEDFX 2011 Product atalog

2 Quik-Spec oordination Panelboard Specifications atalog Symbol: SQSP4 Description Panelboards for commercial/industrial branch or service entrance applications on systems up through 600Vac. Main options Main lug only (MLO) Fused main disconnect on-fused main disconnect 11 PELORDS The SQSP is especially designed to address the E Selective oordination Requirements for Emergency, Legally Required Standby, Healthcare Essential Electrical and ritical Operation Power Systems (OPS) per E , , and ot for applications requiring FI protected circuits. The SQSP is configured to order for the application. To confirm availability of options and constructions, contact your Siemens distributor. Ratings Volts: 600Vac (or less), 125 Vdc mps: 30, 60, 100, 200, 225, 400 SR: 20k or 125Vdc See panelboard short circuit ratings table for ratings. gency information UL 67 Standard for panelboards UL 50/UL 50E Enclosures for electrical equipment S 22.2, o. 29-M1989 Panelboards and encl. panelboards UL listed, class TL panelboard (meets 2002 E limit of 42 overcurrent devices per panel) U and Seismic Qualified and I pproved ranch disconnect options 1-, 2-, and 3-pole 15, 20, 30, 40, 50, 60, 70, 90, and 100 rejecting branch disconnects (see table for details). ranch ampacity on 125Vdc panels limited to SP 40 or less. ranch circuit positions 18, 30 and 42 eutral options Unbonded and bonded 200, 400 and 800 Ground options Isolated and non-isolated Enclosures EM 1 and EM 3R. Other ratings available. onsult factory. Spare fuse compartment Six space spare fuse compartment standard on all models Panelboard Short-circuit urrent Ratings SR main options Main lug only (MLO) a main disc. no fuses a or w/ lass J fuses main disc. no fuses a or w/ lass J fuses SP_F main disc. (60) b High 200k 200k 100k 200k 100k Std. 50k 50k 50k 50k 20k D Main lug only (MLO) a a lass J, T or RK1 fuses upstream, max amps = panel amps. b UEFuse disconnect Siemens Industry, Inc. SPEEDFX 2011 Product atalog 11-77

3 SP ranch Disconnects, UEFuse Revised 02/26/12 Replacement parts and performance data 11 PELORDS I J Fuse and disconnect performance data For details and specifications, access the following data sheets online at UEFuse Specifications atalog Symbols STF_ (6-100 Indicating version) STF_R (1-100 on-indicating version) Description The UEfuse is a finger-safe, dual-element, time delay UL lass F power fuse with lass J fuse electrical performance charcteristics. 10 Seconds minimum operating time at 500% rated current. I P ranch Disconnects Poles mpacity Part o. 1-pole 2-pole 3-pole 15, 20, 30, 40, 50, 60, 70, 90, 100 J UEFuse Fuses For P Part o. SP-(# of poles)-15f SP-(# of poles)-20f SP-(# of poles)-30f SP-(# of poles)-40f SP-(# of poles)-50f on-indicating Part o. STF(amps)R STF1R, STF3R, STF6R, STF10R, STF15R STF17-1/2 R STF20R STF25R STF30R STF35R STF40R STF45R STF50R SP-1-(amp)F SP-2-(amp)F SP-3-(amp)F Indicating Part o. STF(amps) STF6 STF10 STF15 STF17-1/2 STF20 STF25 STF30 STF35 STF40 STF45 STF50 SP-(# of poles)-60f STF60R STF60 SP-(# of poles)-70f STF70R STF70 SP-(# of poles)-90f STF80R STF90R STF80 STF90 SP-(# of poles)-100f STF100R STF100 a P disconnect can accept UEFuses with amp ratings less than or equal to the amp rating of the SP disconnect. 1 indicating UEFuse not available. orrect fit with SP disconnect requires indicating UEFuse with date code R38 or later. Ratings Volts: 600Vac/300Vdc mps: (non-indicating version) (indicating version) IR: 300k RMS Sym. (UL) 200k RMS. Sym (S) 100k D (UL & S) gency Information UL Listed Special Purpose Fuse: Guide JFHR, File E56412 S ertified Fuse: lass , File E compliance for the European Union low voltage directive Other Ratings/Specifications Watts Loss at rated current: STF30: 3.99W STF60: 6.23W STF100: 9.51W Operating and Storage Temperature Range 14 to 149 F(-10 to 65 ) Material Specifications ase: Glass filled PES (Polyethersulfone) Terminals: opper alloy Terminal plating: Electroless tin Indicator lens: PES (Polyethersulfone) (indicating version only) Indicator: Energetic chemical UEFuse, Low-Peak, Quik-Spec, QuikShip, and easyid are valuable trademarks of ooper Industries in the United States and other countries Siemens Industry, Inc. SPEEDFX 2011 Product atalog

4 SP ranch Disconnects, UEFuse Revised 02/26/12 Specifications SP Horsepower Ratings SP Disconnect mp Rating HP Vac SP-(poles)-15F SP-(poles)-20F SP-(poles)-30F SP-(poles)-40F SP-(poles)-50F SP-(poles)-60F SP-(poles)-70F SP-(poles)-90F SP-(poles)-100F PELORDS ranch Disconnects SP Part o. Poles Fuse mp Range Max. SP mp. on-indicating Fuses (Standard) Indicating Fuses (Opt l) SP-1-15F 1 SP-2-15F 2 SP-3-15F STF1R, STF3R, STF6R, STF10R, STF15R STF6 STF10 STF15 SP-1-20F 1 SP-2-20F 2 SP-3-20F STF17-1/2 R STF20R STF17-1/2 STF20 SP-1-30F 1 SP-2-30F 2 SP-3-30F STF25R STF30R STF25 STF30 SP-1-40F 1 SP-2-40F 2 SP-3-40F STF35R STF40R STF35 STF40 SP-1-50F 1 SP-2-50F 2 SP-3-50F STF45R STF50R STF45 STF50 SP-1-60F 1 SP-2-60F STF60R STF60 SP-3-60F 3 SP-1-70F 1 SP-2-70F STF70R STF70 SP-3-70F 3 SP-1-90F 1 SP-2-90F 2 SP-3-90F STF80R STF90R STF80 STF90 SP-1-100F 1 SP-2-100F 2 SP-3-100F STF100R STF100 a SP disconnect can accept UEFuses with amp ratings less than or equal to the amp rating of the SP disconnect. orrect fit with SP disconnect requires indicating UEFuses with date code R30 or later. Siemens Industry, Inc. SPEEDFX 2011 Product atalog 11-79

5 Panelboards PELORDS 11 Enclosure/System Types, & D Voltages Voltages EM 1 Flush or surface mount. Galvanized steel with removable end walls blank or with knockouts to order. ox sizes: 20 W x 5.75 D x 33, 50, 59 or 69 H (510 W x 145 D x 838, 1270, 1500 or 1753mm H). ox can be rotated 180 to accommodate conduit feed. Enclosure and chassis mounting instructions are found in supplied literature. hassis mounts directly onto studs in the enclosure. Trim finished with gray powder coat paint over phosphatized steel (SI 61). Door and door-in-door configurations with locks. Door locks use key # ircuit directory card is located on the inside of the door. Trim screws are concealed. 1 phase, 2 wire 120V 1 phase, 2 wire 240V 1 phase, 2 wire 1 phase, 3 wire 120/240V 1 phase, 3 wire 1 phase, 2 wire, Wye 277V 1 phase, 2 wire 1 phase, 2 wire, Delta 480V 1 phase, 2 wire EM 3R Surface mount only. Finished with gray powder coat paint over phosphatized steel (SI 61). ottom feed only, no knockouts ox sizes: 20 W x 7.7 D x 34.5, 51.5, 60.5 or 70.5 H (510 W x 195 D x 876, 1310, 1535 or 1791mm H). Enclosure and chassis mounting instructions are found in supplied literature hassis mounts directly onto studs in the enclosure. Gasketed door has vault handle with lock. Door locks use key # ircuit directory card is located on the inside of the door. 1 phase, 3 wire, Delta 240/480V 1 phase, 3 wire 3 phase, 4 wire, Wye 208Y/120V 3 phase, 4 wire 480Y/277V 3 phase, 4 wire 600Y/347V 3 phase, 4 wire 3 phase, 4 wire, Delta 240/120V 3 phase, 4 wire 480/240V 3 phase, 4 wire using Tin-plated copper with sufficient cross section to meet UL 67 temperature rise requirements. Distributed 1- & 3-phase busing ll SP branch disconnects can be mounted in any branch circuit position. phase, 3 wire, Delta 240V, 3 phase, 3 wire 480V, 3 phase, 3 wire 600V, 3 phase, 3 wire 240V, 3 phase, 3 wire, grounded 480V, 3 phase, 3 wire, grounded 600V, 3 phase, 3 wire, grounded 3 1 phase, 3 wire, Wye 208Y/120V 1 phase, 3 wire 480Y/277V 1 phase, 3 wire D voltage 1 phase, 2 wire 125Vdc, 2 wire Single-phase Three-phase Siemens Industry, Inc. SPEEDFX 2011 Product atalog (Up to 125Vdc, MLO option only, SP 40 or less.) +125Vdc

6 Dimensions and Panelboard onfigurations EM 1 and 3R Enclosure Dimensions Encl. Type EM 1 Encl. Height Revised 02/26/12 Dimensions (inches) H H MH H DH RH SH DW D / / / PELORDS / EM 3R vailable panelboard configurations ased on enclosure height, panel amp rating and number of branch circuit positions Encl. height (inches) Panel amp rating ranch positions 18 vailable configurations Main lug only, with or without feed-through lugs on-fused disconnect, no loadside options 30 Main lug only, no loadside options through 60 fused main disconnect with or without feed-through lugs or TVSS device through 60 fused main disconnect with or without feed-through lugs or TVSS device through 60 fused main disconnect with or without feed-through lugs or TVSS device through 200 fused main disconnect with or without feed-through lugs or TVSS device through 200 fused disconnect with or without feed-through lugs Main lug only with TVSS device on-fused disconnect, with feed-through lugs or TVSS device Main lugs only, with feed-through lugs or TVSS device on-fused disconnect, with or without feed through lugs Main lug only, with or without feed-through lugs or TVSS device on-fused disconnect, with or without feed-through lugs Main lug only, with ot without feed through lugs or TVSS device on-fused disconnect, with or without feed-through lugs 30 Main lug only, with or without feed-through lugs through 200 fused main disconnect, with TVSS device through 200 fused main disconnect with or without feed-through lugs or TVSS device on-fused disconnect with TVSS device Main lug only with loadside disconnect on-fused disconnect, with TVSS device 225 through 400 fused disconnect with or without feed-through lugs or TVSS device Main lug only, with TVSS device 225 through 400 fused disconnect, with no loadside options Main lug only, with or without feed-through lugs or TVSS device on-fused disconnect, with no loadside options 18 on-fused disconnect, with loadside disconnect Main lug only with loadside disconnect 225 through 400 fused disconnect with feed-through lugs or TVSS device on-fused disconnect, with or without feed through lugs or TVSS device 225 through 400 fused main disconnect, with or without feed-through lugs or TVSS device Siemens Industry, Inc. SPEEDFX 2011 Product atalog 11-81

7 EM 1 and EM 3R Dimensions 11 PELORDS EM 1 Enclosures and Interior DETIL (7/8, 1-1/8) oncentric KO 7.4 lank Endwall Knockout Endwall Enclosures vailable with 2 lank, 2 Knockout, or 1 Each Endwall 3.1 Flush Mount DW Surface Mount DW (1-3/4, 2, 2-1/2, 3, 3-5/8, 4-1/8) oncentric KO Flush Mount DW Surface Mount DW SH Ground Door Lock Flush Mount H H MH eutral RH H Surface Mount H DH Spare Fuse ompartment D 0.25 Mounting Hole Emboss Front View (Door in Door Option Shown on Right) ox with Interior Side View of ox EM 3R Enclosures Interior same as EM 1 SH 2.0 DETIL SLE 1 : 4 Top End Wall (o Knockouts) D 0.6 2X H MH H ox Interior Same as EM DW Front View Side View ottom End Wall (o Knockouts) Siemens Industry, Inc. SPEEDFX 2011 Product atalog

8 Fuse urves Time-urrent haracteristic urves verage Melt 11 PELORDS urrent Limitation urves Siemens Industry, Inc. SPEEDFX 2011 Product atalog 11-83