INFINITY ARCHITECTUR E

Transcription

1 INFINITY ARCHITECTUR E March 3, 2015 Auburn University Plainsman Park Batting Cage Improvements AU # ADDENDUM 1 This Addendum is hereby made part of the Contract Documents to the same extent as though it was originally included therein. Receipt for this Addendum must be acknowledged by the Bidder by statement of receipt indicated on the Proposal Form. GENERAL: 1. All card swipes will be provided and installed by the university. The university will additionaly provide the request to exit button for the gate, the magnetic strike, the panic device for door 3 and all associated conduit and wiring. Notes 6-9 on E2.1 are eliminated. SPECIFICATIONS: 2. Refer to the Section 9900 Lighting, and revise as follows: A. Delete original Section 9900 Lighting, and replace with attached revised Section 9900 Lighting. REVISIONS TO DRAWINGS: 3. Refer to the Sheet A0.1 Demolition Plan, and revise as follows: A. Note 13. The number of gooseneck light fixtures to be removed and replaced with new fixtures is now Refer to the Sheet A0.2 Demolition Elevations, and revise as follows: A. Note 13. The number of gooseneck light fixtures to be removed and replaced with new fixtures is now 5. B. See new section thru the dugout tunnel 2/A0.2. This detail has been added for clarity and additionally notes that the CMU header in the tunnel may have to be demolished and rebuilt as part of the (2) doors being relocated in that tunnel. 5. Refer to the Sheet A1.1 Floor Plan, and revise as follows: A. Dimensions of the new ramp have been modified to sync with the new section 3/A1.2. Addendum 1 Page 1 of 2

2 INFINITY ARCHITECTUR E B. Note 4. On the EIFS band being repainted the caulking above and below the band will be replaced prior to painting. 6. Refer to the Sheet A1.2 Elevation, and revise as follows: A. Keynotes are shown on A1.1. B. See new detail 3/A1.2. This section has been added for clarity and indicates that the CMU header in the dugout tunnel should be rebuilt if demolished. C. The reinforcing of the new ramp around the existing trench drain will have to be coordinated after demolition. 7. Refer to the Sheet A2.1 Details, and revise as follows: A. Door Schedule. Door 2 should have a wireglass lite to match the existing door. Door Type C has been added. B. Details 4 and 5 regarding the ground gate latch have been removed as that latch is no longer in the project. SUBSTITIONS: NONE ATTACHMENTS: RFI Log dated 3/3/2015 New Section 9900 PAINTING Revised Drawing Sheet A0.1 Demolition Plan Revised Drawing Sheet A0.2 Demolition Elevation Revised Drawing Sheet A1.1 Floor Plan Revised Drawing Sheet A1.2 Elevation Revised Drawing Sheet A2.1 Details END OF ADDENDUM 1 Addendum 1 Page 2 of 2

3 RFI No. PRE-BID RFI LOG 3/3/2015 PROJECT: PLAINSMAN PARK BATTING CAGE IMPROVEMENTS PROJECT NO.: Date Rec'd. Sheet or Spec. Sect. Description Source Response By & Date Add. No. 1 3/2/15 A2.1 Sheet A2.1 gate latch. Please provide the location. HBS The latch has been deleted. IA 1 2 3/2/15 General What strength concrete are the walks? HBS 3000 psi IA 1 3 3/2/15 A0.2 Sheet A0.2. Assuming the walls are 4" veneer split face and 8" backup. Is the demo to racked back with new returns to the windows or cut and rubbed only? Is the EIFS band to be replaced at the windows in resonable locations are we attempting to patch the returns. HBS The brick should be cut and rubbed only with no returns. The 6" storefront will make up the air gap between the brick and block. The EIFS band should be cut and patched at the openings. IA 1 4 3/2/15 S1 Sheet S1 section 1. Are we attempting to maintain the radius with the 5x3 angle or can it be installed at the high point of the window and the radius infilled with metal stud and sheathing in leiu of block? HBS No. The angle should go straight across at the highest point of the opening with the radius filled in with stud and drywall on the interior. IA Page 1 of 3

4 RFI No. PRE-BID RFI LOG 3/3/2015 PROJECT: PLAINSMAN PARK BATTING CAGE IMPROVEMENTS PROJECT NO.: Date Rec'd. Sheet or Spec. Sect. Description Source Response By & Date Add. No Page 2 of 3

5 RFI No. PRE-BID RFI LOG 3/3/2015 PROJECT: PLAINSMAN PARK BATTING CAGE IMPROVEMENTS PROJECT NO.: Date Rec'd. Sheet or Spec. Sect. Description Source Response By & Date Add. No Page 3 of 3

6

7 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL SECTION PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and field painting of the following: 1. Exposed items and surfaces. 2. Surface preparation, priming, and finish coats specified in this Section are in addition to shop priming and surface treatment specified in other Sections. B. Paint exposed surfaces, except where the paint schedules indicate that a surface or material is not to be painted or is to remain natural. If the paint schedules do not specifically mention an item or a surface, paint the item or surface the same as similar adjacent materials or surfaces whether or not schedules indicate colors. If the schedules do not indicate color or finish, the Architect will select from standard colors and finishes available. 1. Painting includes field painting of exposed bare and covered pipes and ducts (including color coding), hangers, exposed steel and iron work, and primed metal surfaces of mechanical and electrical equipment. C. Do not paint prefinished items, concealed surfaces, finished metal surfaces, operating parts, and labels. 1. Prefinished items include the following factory-finished components: a. Exposed unpainted piping. b. Plastic laminate faced items. c. Finished flooring. d. Acoustical ceilings. e. Finished mechanical and electrical equipment. f. Light fixtures. g. Distribution cabinets. 2. Concealed surfaces include walls or ceilings in the following generally inaccessible spaces: a. Furred areas. b. Ceiling plenums. c. Attics. d. Pipe spaces. e. Duct shafts. 3. Finished metal surfaces include the following: a. Anodized or organically coated aluminum. PAINTING

8 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL 1.2 SUBMITTALS: b. Stainless steel. c. Chromium plate. d. Copper. e. Bronze and brass. 4. Operating parts include moving parts of operating equipment and the following: a. Valve and damper operators. b. Linkages. c. Sensing devices. d. Motor and fan shafts. 5. Labels: Do not paint over Underwiters Laboratories (UL), Factory Mutual (FM), or other code-required labels or equipment name, identification, performance rating, or nomenclature plates. A. Product Data: 1. Submit complete list of products proposed for use at least 30 days prior to commencement of painting work. 2. Indicate manufacturer, brand name, quality, type, and sheen for each type of paint and for each surface to be finished. 3. Indicate manufacturer s instructions regarding mixing, surface preparation and application. Include application rates, film thickness and required primers. 4. Intent of Contractor to use products specified does not relieve him from responsibility of submitting product list. B. Color Samples: Submit two sets of color samples from paint manufacturers proposed for use, for color and finish selections. C. Card stock brush-outs: Following issue of color schedule, prepare two sets of color coat brush-outs for each paint and sheen scheduled, applying actual finish color coat to standard sample card stock, minimum 80 sq. in. size. 1.3 DEFINITIONS A. General: Standard coating terms defined in ASTM D 16 apply to this Section. 1. Flat refers to a lusterless or matte finish with a gloss range below 15 when measured at an 85-degree meter. 2. Eggshell refers to low-sheen finish with a gloss range between 5 and 20 when measured at a 60-degree meter. 3. Satin refers to low-sheen finish with a gloss range between 15 and 35 when measured at a 60-degree meter. 4. Semigloss refers to medium-sheen finish with a gloss range between 30 and 65 when measured at a 60-degree meter. 5. Full gloss refers to high-sheen finish with a gloss range more than 65 when measured at a 60-degree meter. PAINTING

9 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL 1.4 QUALITY ASSURANCE A. Applicator Qualifications: Engage an experienced applicator who has completed painting system applications similar in material and extent to that indicated for this Project with a record of successful in-service performance. B. Source Limitations: Obtain all materials from one manufacturer. If a material is not available from that manufacturer, obtain that manufacturer s approval. 1.5 DELIVERY, STORAGE, AND HANDLING A. Deliver materials to the Project Site in manufacturer s original, unopened packages and containers bearing manufacturer s name and label, and the following information: 1. Product name or title of material. 2. Product description (generic classification or binder type). 3. Manufacturer s stock number and date of manufacture. 4. Contents by volume, for pigment and vehicle constituents. 5. Thinning instructions. 6. Application instructions. 7. Color name and number. 8. VOC content. B. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient temperature of 45 deg F. Maintain containers used in storage in a clean condition, free of foreign materials and residue. 1. Protect from freezing. Keep storage area neat and orderly. Remove oily rags and waste daily. Take necessary measures to ensure that workers and work areas are protected from fire and health hazards resulting from handling, mixing, and application. 1.6 PROJECT CONDITIONS A. Apply water-based paints only when the temperature of surfaces to be painted and surrounding air temperatures are between 50 and 90 deg F. B. Apply solvent-thinned paints only when the temperature of surfaces to be painted and surrounding air temperatures are between 45 and 95 deg F. C. Do not apply paint in snow, rain, fog, or mist; or when the relative humidity exceeds 85 percent; or at temperatures less than 5 deg F above the dew point; or to damp or wet surfaces. 1. Painting may continue during inclement weather if surfaces and areas to be painted are enclosed and heated within temperature limits specified by manufacturer during application and drying periods. 1.7 EXTRA MATERIALS PAINTING

10 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL A. Furnish extra paint materials from the same production run as the materials applied in the quantities described below. Package paint materials is unopened, factory-sealed containers for storage and identify with labels describing contents. Deliver extra materials to the Owner. 1. Quantity: Furnish the Owner with the additional finish material of at least 1 unopened gal., as appropriate, of each material and color applied. PART 2 PRODUCTS 2.1 MANUFACTURER A. The basis of design is Sherwin Williams. The Paint Schedule lists the systems. B. Paint systems from one of the following manufacturers is acceptable, if all products are comparable to the basis of design. 1. Benjamin Moore & Co. (Moore) 2. PPG Industries, Inc. (PPG) 3. Pratt & Lambert, Inc. (P & L) 2.2 PAINT MATERIALS, GENERAL A. Material Compatibility: Provide block fillers, primers, undercoats, and finish-coat materials that are compatible with one another and the substrates indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field experience. B. Material Quality: Provide manufacturer s best-quality paint material of the various coating types specified. Paint-material containers not displaying manufacturer s product identification will not be acceptable. C. Colors: A maximum of one color will be selected for each space. PART 3 EXECUTION 3.1 EXAMINATION A. Examine substrates, areas, and conditions, with the Applicator present, under which painting will be performed for compliance with paint application requirements. 1. Do not begin to apply paint until unsatisfactory conditions have been corrected and surfaces receiving paint are thoroughly dry. 2. Start of painting will be construed as the Applicator s acceptance of surfaces and conditions within a particular area. B. Coordination of Work: Review other Sections in which primers are provided to ensure PAINTING

11 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL 3.2 PREPARATION compatibility of the total system for various substrates. On request, furnish information on characteristics of finish materials to ensure use of compatible primers. 1. Notify the Architect about anticipated problems using the materials specified over substrates primed by others. A. General: Remove hardware and hardware accessories, plates, machined surfaces, lighting fixtures, and similar items, already installed and are not to be painted, using workers skilled in the trades involved. If removal is impractical or impossible because of the size or weight of the item, provide surface-applied protection before surface preparation and painting. 1. After completing painting operations in each space or area, reinstall items removed using workers skilled in the trades involved. B. Cleaning: Before applying paint or other surface treatments, clean the substrates of substances that could impair the bond of the various coatings. Remove oil and grease before cleaning. 1. Schedule cleaning and painting so dust and other contaminants from the cleaning process will not fall on wet, newly painted surfaces. C. Surface Preparation: Clean and prepare surfaces to be painted according to manufacturer s written instructions for each particular substrate condition and as specified. 1. Provide barrier coats over incompatible primers or remove and reprime. 2. Cementitious Materials: Prepare concrete masonry block surfaces to be painted. Remove efflorescence, chalk, dust, dirt, grease, oils, and release agents. Roughen as required to remove glaze. a. Use abrasive blast-cleaning methods if recommended by paint manufacturer. b. Determine alkalinity and moisture content of surfaces by performing appropriate tests. If surfaces are sufficiently alkaline to cause the finish paint to blister and burn, correct this condition before application. Do not paint surfaces where moisture content exceeds that permitted in manufacturer s written instructions. 3. Concrete Block: a. Remove all loose mortar and foreign material. Surface must be free of laitance, concrete dust, dirt, form release agents, moisture curing membranes, loose cement, and hardeners. b. Concrete block and mortar must be cured at least 30 days at 75 F. The ph of the surface should be between 6 and 9, unless the products to be used are designed to be used in high ph environments such as Loxon. PAINTING

12 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL 4. Ferrous Metals: a. Clean ungalvanized ferrous-metal surfaces that have not been shop coated; remove oil, grease, dirt, loose mill scale, and other foreign substances. Use solvent or mechanical cleaning methods that comply with the Steel Structures Painting Council s (SSPC) recommendations. b. Clean steel surfaces as recommended by paint system manufacturer and according to requirements of SSPC-SP 6. c. Treat bare and pickled clean metal with a metal treatment wash coat before priming. d. Touch up bare areas and shop-applied prime coats that have been damaged. Wire-brush, clean with solvents recommended by paint manufacturer, and touch up with the same primer as the shop coat. 5. Galvanized Metal: a. Allow to weather prior to coating. b. Clean per SSPC-SP1 using detergent and water or a degreasing cleaner, then prime as required. When weathering is not possible or the surface has been treated with chromate s or silicates, first Solvent Clean per SSPC-SP1 and apply a test area, priming as required. c. Allow the coating to dry at least one week before testing. If adhesion is poor, Brush Blast per SSPC-SP7 is necessary to remove these treatments. 6. Previously Coated Surfaces: a. Maintenance painting will frequently not permit or require complete removal of all old coatings prior to repainting. b. All surface contamination such as oil, grease, loose paint, mill scale, dirt, foreign matter, rust, mold, mildew, mortar efflorescence, and sealers must be removed to assure sound bonding to the tightly adhering old paint. Glossy surfaces of old paint films must be clean and dull before repainting. c. Thorough washing with an abrasive cleanser will clean and dull in one operation, or, wash thoroughly and dull by sanding. Spot prime any bare areas with an appropriate primer. d. Check for compatibility by applying a test patch of the recommended coating system, covering at least 2 to 3 sq. ft. Allow to dry one week before testing adhesion per ASTM D3359. If the coating system is incompatible, complete removal is required. D. Materials Preparation: Mix and prepare paint materials according to manufacturer s written instructions. 1. Maintain containers used in mixing and applying paint in a clean condition, free of foreign materials and residue. 2. Stir material before application to produce a mixture of uniform density. Stir as required during application. Do not stir surface film into material. If necessary, remove surface film and strain material before using. PAINTING

13 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL 3. Use only thinners approved by paint manufacturer and only within recommended limits. E. Tinting: Tint each undercoat a lighter shade to simplify identification of each coat when multiple coats of the same material area applied. Tint undercoats to match the color of the finish coat, but provide sufficient differences in shade of undercoats to distinguish each separate coat. 3.3 APPLICATION A. General: Apply paint according to manufacturer s written instructions. Use applicators and techniques best suited for substrate and type of material being applied. 1. Paint colors, surface treatments, and finishes are indicated in the Schedules. 2. Do not paint over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions detrimental to formation of a durable paint film. 3. Provide finish coats that are compatible with primers used. 4. The term exposed surfaces includes areas visible when permanent or built-in fixtures, covers, grilles, and similar components are in place. Extend coatings in these areas, as required, to maintain the system integrity and provide desired protection. 5. Paint surfaces behind movable equipment and furniture the same as similar exposed surfaces. Before the final installation of equipment, paint surfaces behind permanently fixed equipment or furniture with prime coat only. 6. Finish doors on tops, bottoms, and side edges the same as exterior faces. B. Scheduling Painting: Apply first coat to surfaces that have been cleaned, pretreated, or otherwise prepared for painting as soon as practicable after preparation and before subsequent surface deterioration. 1. The number of coats and the film thickness required are the same regardless of application method. Do not apply succeeding coats until the previous coat has cured as recommended by the manufacturer. If sanding is required to product a smooth, even surface according to manufacturer s written instructions, sand between applications. 2. Omit primer on metal surfaces that have been shop primed and touchup painted, when appropriate. 3. If undercoats, stains, or other conditions show through final coat of paint, apply additional coats until paint film is of uniform finish, color, and appearance. Give special attention to ensure edges, corners, crevices, welds, and exposed fasteners receive a dry film thickness equivalent to that of flat surfaces. 4. Allow sufficient time between successive coats to permit proper drying. Do not recoat surfaces until paint has dried to where it feels firm, does not deform or feel sticky under moderate thumb pressure, and where application of another coat of paint does not cause the undercoat to lift or lose adhesion. C. Application Procedures: Apply paints and coatings by brush, roller, spray, or other applicators according to manufacturer s written instruction. 1. Brushes: Use brushes best suited for the type of material applied. Use brush of PAINTING

14 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL appropriate size for the surface or item being painted. 2. Rollers: Use rollers of carpet, velvet back, or high-pile sheep s wood as recommended by the manufacturer for the material and texture required. 3. Spray Equipment: Use airless spray equipment with orifice size as recommended by the manufacturer for the material and texture required. D. Minimum Coating Thickness: Apply paint materials no thinner than manufacturer s recommended spreading rate. Provide the total dry film thickness of the entire system as recommended by the manufacturer. E. Mechanical and Electrical Work: Painting of mechanical and electrical work is limited to items exposed in equipment rooms and in occupied spaces. F. Block Fillers: Apply block fillers to concrete masonry block at a rate to ensure complete coverage with pores filled. G. Prime Coats: Before applying finish coats, apply a prime coat of material, as recommended by the manufacturer, to material that is required to be painted or finished and that has not been prime coated by others. Recoat primed and sealed surfaces where evidence of suction spots or unsealed areas in first coat appears, to ensure a finish coat with no burn through or other defects due to insufficient sealing. H. Pigmented (Opaque) Finishes: Completely cover surfaces as necessary to provide a smooth, opaque surface of uniform finish, color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections will not be acceptable. I. Completed Work: Remove, refinish, or repaint work not complying with requirements. 3.4 FIELD QUALITY CONTROL A. The Owner reserves the right to invoke the following test procedures at any time and as often as the Owner deems necessary during the period when paint is being applied: 1. The Owner may engage the services of an independent testing agency to sample the paint material being used. Samples of material delivered to the Project will be taken, identified, sealed, and certified in the presence of the Contractor. 2. The testing agency will perform appropriate tests for the following characteristics as required by the Owner: a. Quantitative material analysis. b. Abrasion resistance. c. Apparent reflectivity. d. Flexibility. e. Washability. f. Absorption. g. Accelerated weathering. h. Dry opacity. i. Accelerated yellowness. PAINTING

15 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL 3.5 CLEANING j. Recoating. k. Skinning. l. Color retention. m. Alkali and mildew resistance. 3. The Owner may direct the Contractor to stop painting if test results show material being used does not comply with specified requirements. The Contractor shall remove non-complying paint from the site, pay for testing, and repaint surfaces previously coated with the rejected paint. If necessary, the Contractor may be required to remove rejected paint from previously painted surfaces if, on repainting with specified paint, the 2 coatings are incompatible. A. Cleanup: At the end of each workday, remove empty cans, rags, rubbish, and other discarded paint materials from the site. 3.6 PROTECTION 1. After completing painting, clean glass and paint-spattered surfaces. Remove spattered paint by washing and scraping. Be careful not to scratch or damage adjacent finished surfaces. A. Protect work of other trades, whether being painted or not, against damage by painting. Correct damage by cleaning, repairing or replacing, and repainting, as approved by Architect. B. Provide Wet Paint signs to protect newly painted finishes. Remove temporary protective wrappings provided by others to protect their work after completing painting operations. 3.7 PAINT SCHEDULE 1. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces. Comply with procedures specified in PDCA P1. A. Concrete Block, Except Toilet Rooms and Concessions: 1. New: a. Primer: B42W00046 Heavy Duty Block Filler, White b. 2 Coats: A84W00151 SuperPaint Latex Gloss House & Trim Paint With Extended Open Time, Extra White c. Color is specified on drawings. 2. Existing: a. Primer: B51W00050 Adhesion, Off White b. 2 Coats: A84W00151 SuperPaint Latex Gloss House & Trim Paint with Extended Open Time, Extra White c. Color is specified on drawings. PAINTING

16 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL B. Concrete Blocks, Toilet Rooms and Concessions: 1. New: a. Primer: B42W00046 Heavy Duty Block Filler, White b. 2 Coats: K46W00151 Pro Industrial PreCatalyzed Waterbased Semi- Gloss Epoxy, Extra White 2. Existing: a. Primer: B51W00050 Adhesion Primer, Off White b. 2 Coats: K46W00151 Pro Industrial PreCatalyzed Waterbased Semi- Gloss Epoxy, Extra White C. Galvanized Metal Substrates: 1. Primer: B66A00310 Pro Industrial Pro-Cryl Universal Primer Gray (cirrus std) Coats: B66W00111 DTM Acrylic Coating Gloss. D. Ferrous Metal / New & Existing, Except Handrails: 1. Primer: B66A00310 Pro Industrial Pro-Cryl Universal Primer Gray (cirrus std.) 2. 2 Coats: B66W00111 DTM Acrylic Coating Gloss. E. Ferrous Metal Handrails (Previously Painted): 1. Primer: B66A00310 Pro Industrial Pro-Cryl Universal Primer Gray (cirrus std.) a. Only where previous coating is alkyd based enamel or multiple layers of existing coating can not be removed. If coating can be removed by app 80%, use epoxy primer Coats: B65T00304 Hi-Solids Polyurethane Gloss 3. Auburn Blue to match existing. F. Ferrous Metal Fencing (No Paint): 1. Primer: B58W00610 Macropoxy 646 Fast Cure Epoxy a. Use on new ferrous or galvanized metal. Also can be use on previously coated where previous coating can be removed to 80% or more. Test for compatibility before proceeding Coats: B65T00304 Hi-Solids Polyurethane Gloss 3. Auburn Blue to match existing. END OF SECTION PAINTING

17 BATTING CAGE IMPROVEMENTS ARCHITECT S PROJECT NUMBER: PLAINSMAN PARK AU PROJECT NUMBER: AUBURN UNIVERSITY AUBURN, AL PAINTING

18

19

20

21

22