PrePumpingGroup User s Guide. PrePumpingGroup Class

Transcription

1 TANGO Device Server PrePumpingGroup User s Guide PrePumpingGroup Class Revision: release_1_0_0 - Author: coquet Implemented in C++ Introduction: This DS drives one vacuum pre-pumping group Class Inheritance: Tango::Device_3Impl PrePumpingGroup Properties:

2 Device Properties Property name Property type Description ProfibusServerName Tango::DEV_STRING device name of the Profibus Server BoardNumber number of the Profibus DP Hilsher card ( from 0 to 3 ) default : 0 DPAddress Group InputOffset InputLength OutputOffset OutputLength Device Properties Default Values: DP Address of the power supply from 1 to 125 DO NOT USE 0, 126,127 reserved for the system! Default : 3 Sync/Freeze Group groupe de sync/freeze parametre de 1 to 8. Default : 1 Memory offset of input data ( seen by the master ) offset mï ½moire des entrï ½es de l esclave tel que dï ½fini dans le configurateur Profibus ength in bytes of input data taille en octets de la totalitï ½ des entrï ½es de l esclave tel que dï ½fini dans le configurateur Profibus Ces donnï ½es doivent ï ½tre consï ½cutives. Memory offset of output data ( seen by the master ) offset mï ½moire dessorties de l esclave tel que dï ½fini dans le configurateur Profibus length in bytes of output data taille en octets de la totalitï ½ des sorties de l esclave tel que dï ½fini dans le configurateur Profibus Ces donnï ½es doivent ï ½tre consï ½cutives. Property Name ProfibusServerName BoardNumber DPAddress Group InputOffset InputLength OutputOffset OutputLength Default Values There is no Class properties. States:

3 Names UNKNOWN DISABLE FAULT ALARM States Descriptions Communication is broken The remote control of the pumping group is disabled The gauge controller or the turbo pump is faulty pressure is higher than controller setpoint ( tuned directly on the controller, not by network Attributes: Scalar Attributes Attribute name Data Type R/W Type Expert pressure: pressure read by the group gauge DEV_DOUBLE READ No Commands: More Details on commands... Device Commands for Operator Level Command name Argument In Argument Out Init DEV_VOID DEV_VOID State DEV_VOID DEV_STATE Status DEV_VOID CONST_DEV_STRING PrimaryPumpON DEV_VOID DEV_VOID PrimaryPumpOFF DEV_VOID DEV_VOID TurboPumpON DEV_VOID DEV_VOID TurboPumpOFF DEV_VOID DEV_VOID

4 1 - Init Description: This commands re-initialise a device keeping the same network connection. After an Init command executed on a device, it is not necessary for client to re-connect to the device. This command first calls the device delete_device() method and then execute its init_device() method. For C++ device server, all the memory allocated in the nit_device() method must be freed in the delete_device() method. The language device desctructor automatically calls the delete_device() method. none. none. 2 - State Description: This command gets the device state (stored in its device_state data member) and returns it to the caller. none. DEV_STATE : State Code 3 - Status Description: This command gets the device status (stored in its device_status data member) and returns it to the caller. none. CONST_DEV_STRING : Status description

5 4 - PrimaryPumpON Description: turns primary pump on 5 - PrimaryPumpOFF Description: turns primary pump off 6 - TurboPumpON Description: 7 - TurboPumpOFF Description:

6 ESRF - Software Engineering Group

7 TANGO Device Server PrePumpingGroup User s Guide PrePumpingGroup Class Revision: release_1_0_0 - Author: coquet Implemented in C++ Introduction: This DS drives one vacuum pre-pumping group Class Inheritance: Tango::Device_3Impl PrePumpingGroup Properties:

8 Device Properties Property name Property type Description ProfibusServerName Tango::DEV_STRING device name of the Profibus Server BoardNumber number of the Profibus DP Hilsher card ( from 0 to 3 ) default : 0 DPAddress Group InputOffset InputLength OutputOffset OutputLength Device Properties Default Values: DP Address of the power supply from 1 to 125 DO NOT USE 0, 126,127 reserved for the system! Default : 3 Sync/Freeze Group groupe de sync/freeze parametre de 1 to 8. Default : 1 Memory offset of input data ( seen by the master ) offset mï ½moire des entrï ½es de l esclave tel que dï ½fini dans le configurateur Profibus ength in bytes of input data taille en octets de la totalitï ½ des entrï ½es de l esclave tel que dï ½fini dans le configurateur Profibus Ces donnï ½es doivent ï ½tre consï ½cutives. Memory offset of output data ( seen by the master ) offset mï ½moire dessorties de l esclave tel que dï ½fini dans le configurateur Profibus length in bytes of output data taille en octets de la totalitï ½ des sorties de l esclave tel que dï ½fini dans le configurateur Profibus Ces donnï ½es doivent ï ½tre consï ½cutives. Property Name ProfibusServerName BoardNumber DPAddress Group InputOffset InputLength OutputOffset OutputLength Default Values There is no Class properties. States:

9 Names UNKNOWN DISABLE FAULT ALARM States Descriptions Communication is broken The remote control of the pumping group is disabled The gauge controller or the turbo pump is faulty pressure is higher than controller setpoint ( tuned directly on the controller, not by network Attributes: Scalar Attributes Attribute name Data Type R/W Type Expert pressure: pressure read by the group gauge DEV_DOUBLE READ No Commands: More Details on commands... Device Commands for Operator Level Command name Argument In Argument Out Init DEV_VOID DEV_VOID State DEV_VOID DEV_STATE Status DEV_VOID CONST_DEV_STRING PrimaryPumpON DEV_VOID DEV_VOID PrimaryPumpOFF DEV_VOID DEV_VOID TurboPumpON DEV_VOID DEV_VOID TurboPumpOFF DEV_VOID DEV_VOID

10 1 - Init Description: This commands re-initialise a device keeping the same network connection. After an Init command executed on a device, it is not necessary for client to re-connect to the device. This command first calls the device delete_device() method and then execute its init_device() method. For C++ device server, all the memory allocated in the nit_device() method must be freed in the delete_device() method. The language device desctructor automatically calls the delete_device() method. none. none. 2 - State Description: This command gets the device state (stored in its device_state data member) and returns it to the caller. none. DEV_STATE : State Code 3 - Status Description: This command gets the device status (stored in its device_status data member) and returns it to the caller. none. CONST_DEV_STRING : Status description

11 4 - PrimaryPumpON Description: turns primary pump on 5 - PrimaryPumpOFF Description: turns primary pump off 6 - TurboPumpON Description: 7 - TurboPumpOFF Description:

12 ESRF - Software Engineering Group

13 Frame Alert This document is designed to be viewed using the frames feature. If you see this message, you are using a non-frame-capable web client. Link to Non-frame version.

14 TANGO Device Server PrePumpingGroup Device Commands Description PrePumpingGroup Class Revision: release_1_0_0 - Author: coquet 1 - Init Description: This commands re-initialise a device keeping the same network connection. After an Init command executed on a device, it is not necessary for client to re-connect to the device. This command first calls the device delete_device() method and then execute its init_device() method. For C++ device server, all the memory allocated in the nit_device() method must be freed in the delete_device() method. The language device desctructor automatically calls the delete_device() method. none. none. 2 - State Description: This command gets the device state (stored in its device_state data member) and returns it to the caller. none.

15 DEV_STATE : State Code 3 - Status Description: This command gets the device status (stored in its device_status data member) and returns it to the caller. none. CONST_DEV_STRING : Status description 4 - PrimaryPumpON Description: turns primary pump on

16 5 - PrimaryPumpOFF Description: turns primary pump off 6 - TurboPumpON Description: 7 - TurboPumpOFF Description:

17 ESRF - Software Engineering Group