DuPont Flashing Systems Installation Guidelines

Transcription

1 Installation Instructions for Windows and Doors EFORE Water-Resistive arrier (WR) is Installed DuPont Flashing Systems Installation Guidelines INSTLLTION INSTRUTIONS FOR WINDOWS ND DOORS EFORE WTER-RESISTIVE RRIER (WR) IS INSTLLED FOR UILDINGS LESS THN 5 STORIES REVISION 10/11

2 Table of ontents pplicable Products... 2 Necessary Materials... 2 Optional Materials... 2 Recommended Primers... 3 DuPont Recommended Low Expansion Foams... 3 DuPont Recommended Fasteners... 3 General Instructions... 3 Integral Flanged Window... 5 Integral Flanged Door rick Mold Window rick Mold Door Field pplied Flanged Window Field pplied Flanged Door Non-Flanged Window Non-Flanged Door lternate Head Detail for ir arrier Installations Integral Flanged Windows in Recessed Openings Integral Flanged Windows in Recessed Openings with Open Stud onstruction Key Installation Requirements for Drainable Window / Door Installation Under the Product and Labor Warranty pplicable Products Flashing Products PRODUT DIMENSIONS RE DuPont FlexWrap NF* 6 in x 75 ft sq ft 9 in x 75 ft sq ft DuPont FlexWrap * 9 in x 75 ft 56.2 sq ft 9 in x 250 ft sq ft DuPont StraightFlash 4 in x 150 ft 50 sq ft 9 in x 125 ft sq ft DuPont StraightFlash VF 6 in x 125 ft 62.5 sq ft DuPont Flashing Tape 4 in x 100 ft sq ft 6 in x 100 ft 50.2 sq ft 9 in x 100 ft 75 sq ft DuPont FlexWrap RW for Single Stud pplication 9 in x 6 in 0.38 sq ft DuPont FlexWrap RW for Double Stud pplication 9 in x 6 in 0.38 sq ft * These installation instructions are applicable to both DuPont FlexWrap and FlexWrap NF which can be used interchangeably throughout the installation guide. Necessary Materials DuPont Flashing DuPont Tyvek Tape DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant Optional Materials DuPont Tyvek Wrap aps or other recommended fasteners rushes for Surface Preparation acker rod J -roller Recommended Primers L shaped back dam is a 3/4 corner guard (used on interior gypsum) opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 2

3 Recommended Primers* MNUFTURER PRODUT NME 3M Hi-Strength 90 Denso utyl Primer (spray or can) *pply per manufacturers guidelines. For non-dupont products, DuPont assumes no liability in use of recommended products; installers need to evaluate suitability of recommended products in their end-use applications. DuPont Recommended Low Expansion Foams MNUFTURER DuPont DuPont Recommended Fasteners* MNUFTURER DuPont DuPont DuPont DuPont Tyvek Wrap ap with alternate screws PRODUT NME DuPont Window & Door Foam PRODUT NME DuPont Tyvek Wrap ap nails DuPont Tyvek Wrap ap screws DuPont Tyvek Wrap ap staples (for Stinger or rossfire cap stapler)** 1.0 inch minimum crown staples** * pply per manufacturers guidelines. For non DuPont products, DuPont assumes no liability for use of recommended products; installers need to evaluate suitability of recommended products in their end-use applications. ** Except when installing DuPont Tyvek WRs over foam sheathing and other non-nail-base sheathings. Warranty Please see DuPont Weatherization Products Limited Warranty for buildings less than 5 stories at General Instructions For buildings less than 5 stories For performance requirements exceeding STM E1677, 65 mph equivalent structural load and 15 mph equivalent wind-driven rain water infiltration for buildings less than 5 stories, or for installations that specify a window/door design rating of DP45 or greater, it is recommended to install a high pressure skirt to help prevent water intrusion at the sill or threshold and follow the DuPont Flashing Systems ommercial Installation Guidelines. DuPont Flashing Systems products should be installed on clean, dry surfaces that are free of frost. Wipe surfaces to remove moisture, dirt, grease and other debris that could interfere with adhesion. When cutting the Water-Resistive arrier (WR) to prepare the opening, remove an additional 1 strip of the WR head flap to allow more room for the tape adhesive to seal the head flashing. pply pressure along entire surface of flashing for a good bond using a J-roller or firm hand pressure. Remove all wrinkles and bubbles that may allow for water intrusion by smoothing surface and repositioning as necessary. When flashing the sill area for windows and doors, DuPont recommends the use of 6 wide DuPont Flexwrap NF for 2 x 4 framing and 9 wide DuPont Flexwrap NF for 2 x 6 framing. s an option, if a rigid back dam is desired, cut the corner back dam the length of the sill and nail into place on the interior edge of the sill prior to installation of DuPont Flexwrap NF. Then install DuPont Flexwrap NF over sill and corner guard back dam. If using 6 DuPont FlexWrap NF with optional rigid back dam, seal ends of corner guard with DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 3

4 Door and window rough sill framing must be level or slightly sloped to the exterior to ensure proper drainage to the exterior. This best practice ensures continuous support with positive slope to the exterior. DuPont Residential Sealant and DuPont ommercial Sealant should be tooled flat to allow the natural curing process to create a concave joint. Please contact your local DuPont Tyvek Specialist for additional information and installation support. DO NOT STRETH DuPont FlexWrap NF when installing along the length of sills or jambs. DuPont FlexWrap NF is only intended to be extended when covering corners or curved sections. These installation instructions are applicable to both DuPont FlexWrap NF and FlexWrap which can be used interchangeably throughout the installation guide. However, DuPont FlexWrap must be secured with recommended fasteners as shown in the illustration at right. DuPont Flashing Systems products perform best when installed at temperatures above 25 F ( 4 ). DuPont Flashing Systems products should not be installed over cap fasteners. Priming is generally not required for adhering DuPont Flashing Systems products to most common building materials. However, adverse weather conditions or cold temperatures may require use of a primer to promote adhesion. dditionally, concrete, masonry, and glass mat gypsum sheathing require the use of approved primers. For primer recommendations, see page 3. For additional guidelines, please call Tyvek ( ), visit our website at or consult your local DuPont Tyvek Specialist. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 4

5 Integral Flanged Window EFORE Water-Resistive arrier (WR) is Installed Method applies to the following products: DuPont StraightFlash, DuPont FlexWrap NF, and DuPont Flashing Tape STEP 1 FOR RETNGULR WINDOWS. ttach apron made of DuPont Tyvek WR under sill. pron should extend at least 10 beyond sides of rough opening jambs (or to first stud in open stud construction), and far enough below the rough opening to overlap the sill plate or the DuPont Tyvek WR below. The top of the apron should be securely attached to the wall and the bottom of the apron should be left unsecured so it can overlap the DuPont Tyvek WR which will be installed after the window.. ut DuPont FlexWrap NF at least 12 LONGER than width of sill rough opening (S).. Remove first piece of release paper, cover horizontal sill by aligning inside edge of sill, and adhere into rough opening across sill and up jambs (min. 6 on each side). D. Remove second release paper. E. Fan out DuPont FlexWrap NF at bottom corners onto the face of the wall. overage of DuPont FlexWrap NF should be 2 to 3 onto the face of the wall. No Gap in orner Door Jamb DuPont FlexWrap NF WRONG Sill ORRET (S) 4 FRONT VIEW ORNER DETIL 10 Sill Width + 12 inches 6 Minimum DO NOT STRETH E opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 5

6 STEP 2. pply DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant on three sides (jambs and head) as shown below. If sealant is applied to the sill, ensure that there are at least two (2) 2 gaps in the sealant bead for every 4 of window to allow for drainage. STEP 3 - FOR RETNGULR WINDOWS. Install window according to manufacturer s instructions.. ut two pieces of DuPont StraightFlash, DuPont FlexWrap NF, or DuPont Flashing Tape for jamb flashing extending 1 above window head flange and below bottom edge of sill flashing. Remove release paper and press tightly along sides of window frame.. ut a piece of DuPont StraightFlash, DuPont FlexWrap NF, or DuPont Flashing Tape for head flashing, which extends beyond outer edges of jamb flashings. Remove release paper and install completely covering flange and adhering to exposed sheathing or framing members. NOTE: Ensure proper shingling. DuPont StraightFlash, DuPont Flashing Tape, or DuPont FlexWrap NF at jambs must overlap the DuPont FlexWrap NF at the sill and adhere to the DuPont Tyvek WR below the sill. 1 Minimum INORRET DuPont FlexWrap NF reverse flashed INORRET DuPont StraightFlash flush with DuPont FlexWrap NF ORRET DuPont StraightFlash overlaps DuPont FlexWrap NF opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 6

7 STEP 4 FOR ROUNDTOP WINDOWS NOTE: Follow rectangular window instructions (Steps 1 through 3) for proper installation of sill and jamb flashing prior to head flashing installation.. ut DuPont FlexWrap NF head flashing at least 12 LONGER than the arc length (H) of roundtop window.. Remove both release papers and install to conform around top of window, covering entire mounting flange and adhering to exposed sheathing or framing members. Head flashing should overlap jamb flashings by at least 6. STEP 5 Install DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant (and backer rod as necessary) around the window opening at the interior. It is also acceptable to use DuPont Window and Door Foam or recommended foam. The seal created by the sealant (and backer rod as necessary) or foam will also serve as a back dam. DuPont Residential Sealant or DuPont ommercial Sealant should be tooled flat to allow the natural curing process to create a concave shape. e sure that the sealant penetrates the grooves of the DuPont FlexWrap NF around the sill. NOTE: Installations that specify a window/door design rating of DP45 or greater require extra precautions. See General Instructions for performance requirements exceeding this design rating. (H) 6 Minimum opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 7

8 STEP 6 fter installing the DuPont Tyvek WR, cut as shown to expose window and apron. (Refer to the DuPont Tyvek Water-Resistive and ir arriers Installation Guidelines to install the DuPont Tyvek WR properly). DO NOT UT THROUGH THE DUPONT FLSHING SYSTEMS PRODUTS OR PRON. STEP 7 Final Step. Tape seams as shown. DO NOT TPE at bottom of window. t the head, continuous tape seams as shown with DuPont Tyvek Tape. Skip-taping at the head is acceptable if an air barrier is not required or if additional drainage is desired.. Lap bottom of apron and DuPont Tyvek WR over building materials below for proper shingling. Window DuPont FlexWrap NF pron made of DuPont Tyvek WR Place apron over lower layer of DuPont Tyvek WR 6 Minimum Overlap DuPont Tyvek WR SIDE VIEW DETIL DO NOT UT through DuPont Flashing Systems Products or apron. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 8

9 LTERNTE TPE DETIL Place a continuous bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant around the jamb and head flashing under the DuPont Tyvek WR. Press the DuPont Tyvek WR securely into the sealant. Rectangular Window Round-top Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 9

10 Integral Flanged Door EFORE Water-Resistive arrier (WR) is Installed This method can be used for doors with field applied flanges. This installation guideline is intended for doors installed above grade and/or with wood floor construction. Method applies to the following products: DuPont StraightFlash, DuPont FlexWrap NF and DuPont Flashing Tape STEP 1. ttach apron made of DuPont Tyvek WR under sill. pron should extend at least 10 beyond sides of rough opening jambs (or to first stud in open stud construction), and far enough below the rough opening to overlap the sill plate or the DuPont Tyvek WR below. The top of the apron should be securely attached to the wall and the bottom of the apron should be left unsecured so it can overlap the DuPont Tyvek WR which will be installed after the door. 10 opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 10

11 STEP 2 Preparation of sill flashing:. ut 9 DuPont FlexWrap NF at least 12 LONGER than the width of the sill (S).. 9 DuPont FlexWrap NF has perforated release paper to help with the formation of the back dam. To ensure that the perforation tears cleanly, fold the perforation 180 and crease the flashing.. Remove the two widest pieces of release paper leaving the narrowest release paper on the flashing. When the finished floor is applied, the release paper can be removed and the back dam can be completed. STEP 3. Install the sill flashing as indicated leaving the 1 of DuPont FlexWrap NF with release paper extending it past the door threshold on the inside. When the 1 of release paper is removed, there should be 3/4 of flashing to form the back dam. OPTIONL: Some flooring cannot accomodate a back dam. In that case fold the 1 back dam on top of DuPont FlexWrap NF in the sill. Door will be installed on top of 1 fold to create a back dam (see Side View Detail in Step 7). EXTERIOR INTERIOR Door Front 6-inch for 2x4-inch studs 9-inch for 2x6-inch studs Overlap Scored Release Paper Optional Door Threshold Transition Threshold Flooring ack DuPont StraightFlash High Pressure Skirt (See Step 6 Optional) DuPont FlexWrap NF DuPont Tyvek WR Sub Floor orner Guard (optional) Sheathing SIDE VIEW DETIL (S) No Gap in orner Door Jamb DuPont FlexWrap NF Sill Width + 12 inches reak Scored Release Paper Peel Off 2-pieces of Release Paper WRONG Sill ORRET FRONT VIEW ORNER DETIL 6 Minimum DO NOT STRETH opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 11

12 STEP 4. Fan out DuPont FlexWrap NF at bottom corners onto the face of the wall. overage of DuPont FlexWrap NF should be 2 to 3 onto the face of the wall. STEP 5 pply DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant on three sides (jambs and head) as shown below. If sealant is applied to the sill, ensure that there are at least two (2) 2 gaps in the sealant bead for every 4 of window to allow for drainage. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 12

13 STEP 6 (OPTIONL - HIGH PRESSURE SKIRT) For extreme weather conditions, performance requirements exceeding STM E1677, or window/door design ratings of DP45 or greater, see General Instructions.. reate the high pressure skirt by cutting a piece of DuPont Tyvek WR 1 wider than the width of door opening and approximately 10 in depth.. ut a piece of DuPont StraightFlash or DuPont Flashing Tape to the same width as the skirt. Remove release paper from one side of the DuPont StraightFlash and adhere to the DuPont Tyvek WR.. The skirt may be made with DuPont StraightFlash, DuPont Flashing Tape, or DuPont StraightFlash VF. 4 DuPont StraightFlash utyl dhesive 10 Peel Off Release Paper and attach to underside of door opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 13

14 STEP 7. OPTIONL: dhere high pressure skirt to bottom of threshold of the door.. Install door according to manufacturer s instructions.. ut two pieces of DuPont StraightFlash, DuPont FlexWrap NF, or DuPont Flashing Tape for jamb flashing extending 1 above door head flange and below bottom edge of high pressure skirt. Remove release paper and press tightly along sides of door frame. D. ut a piece of DuPont StraightFlash, DuPont FlexWrap NF or DuPont Flashing Tape for head flashing, which extends beyond outer edges of jamb flashings. Remove release paper and install completely covering mounting flange and adhering to exposed sheathing or framing members. D INORRET DuPont FlexWrap NF reverse flashed INORRET DuPont StraightFlash flush with DuPont FlexWrap NF ORRET DuPont StraightFlash overlaps DuPont FlexWrap NF NOTE: Ensure proper shingling. DuPont StraightFlash, DuPont Flashing Tape, or DuPont FlexWrap NF at jambs must overlap the DuPont FlexWrap NF at the sill and adhere to the DuPont Tyvek WR below the sill. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 14

15 STEP 8 fter installing the DuPont Tyvek WR, cut as shown to expose door and apron. (Refer to the DuPont Tyvek Water-Resistive and ir arriers Installation Guidelines to install the DuPont Tyvek WR properly). DO NOT UT THROUGH THE DUPONT FLSHING SYSTEMS PRODUTS OR PRON. STEP 9. Tape seams as shown. DO NOT TPE at bottom of window. t the head, continuous tape seams as shown with DuPont Tyvek Tape. Skip-taping at the head is acceptable if an air barrier is not required or if additional drainage is desired.. Lap bottom of apron and the DuPont Tyvek WR over building materials below for proper shingling. DO NOT UT through DuPont Flashing Systems Products or apron. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 15

16 LTERNTE TPE DETIL Place a continuous bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant around the jamb and head flashing under the DuPont Tyvek WR. Press the DuPont Tyvek WR securely into the sealant. STEP 10 Final Step. When the interior flooring is ready to install, remove release paper and use Folding Option One or Two (shown below) to form back dam.. Install DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant (and backer rod as necessary) around the door opening at the interior. It is also acceptable to use DuPont Window & Door Foam or recommended foam. The seal created by the sealant (and backer rod as necessary) or foam will also serve as a back dam. DuPont Residential Sealant or DuPont ommercial Sealant should be tooled flat to allow the natural curing process to create a concave shape. e sure that the sealant penetrates the grooves of the DuPont FlexWrap NF around the sill. NOTE: Installations that specify a window/door design rating of DP45 or greater require extra precautions. See General Instructions for performance requirements exceeding this design rating. Folding Option One Folding Option Two OR Fold Out and Up Fold In and Up Fastening Option One Fastening Option Two OR Staples Tape opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 16

17 rick Mold Window EFORE Water-Resistive arrier (WR) Is Installed This installation guide can also be used for windows with field applied nailing fins and non-flanged windows. Method applies to the following products: DuPont StraightFlash, DuPont FlexWrap NF, and DuPont Flashing Tape STEP 1 FOR RETNGULR WINDOWS. ttach apron made of DuPont Tyvek WR under sill. pron should extend at least 10 beyond sides of rough opening jambs (or to first stud in open stud construction), and far enough below the rough opening to overlap the sill plate or the DuPont Tyvek WR below. The top of the apron should be securely attached to the wall and the bottom of the apron should be left unsecured so it can overlap the DuPont Tyvek WR which will be installed after the window.. ut DuPont FlexWrap NF at least 12 longer than width of sill rough opening (S).. Remove first piece of release paper, cover horizontal sill by aligning inside edge of sill, and adhere into rough opening across sill and up jambs (min. 6 on each side). D. Remove second release paper. E. Fan out DuPont FlexWrap NF at bottom corners onto the face of the wall. overage of DuPont FlexWrap NF should be 2 to 3 onto the face of the wall. No Gap in orner Door Jamb DuPont FlexWrap NF WRONG Sill ORRET (S) 4 FRONT VIEW ORNER DETIL 10 Sill Width + 12 inches 6 Minimum DO NOT STRETH E opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 17

18 STEP 2. Prepare head flashing by cutting a piece of DuPont StraightFlash VF at least twelve (12) inches LONGER than the head length.. reak the scored release paper on one side of the head flashing by folding it back and forth upon itself.. enter the DuPont StraightFlash VF along the length of the window head and position so that it contacts the window frame and interior side of the brick mold or flange. Remove the outer release paper and adhere the flashing to the window frame. Use the inner release paper to form a tight seal in the corner. D. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. E. eginning at the junction of the jamb and the head, and away from the corner, cut DuPont StraightFlash VF at a 45 angle. F. Fold the newly created flaps down against the brick mold or flange. G. Fold remaining head flashing flaps down onto the jamb. rick Mold E Scored Release Paper utyl VIEW - Window E F G Window Window Window Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 18

19 STEP 3. Prepare jamb flashing by cutting a piece of DuPont StraightFlash VF at least six (6) inches LONGER than the jamb.. reak the scored release paper on one side of the jamb flashing by folding it back and forth upon itself. Position so that the DuPont StraightFlash VF contacts the window frame and interior side of the brick mold or flange. Ensure that the jamb flashing is positioned 1-1/2 inch below the top edge of the head flashing. Jamb flashing adhesive must come in contact with head flashing adhesive and overlap one inch. D. Remove the outer release paper and adhere the flashing to the window frame. Use the inner release paper to form a tight seal in the corner. E. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. F. Repeat on opposite jamb. Make sure the adhesive on these pieces will overlap. 1-1/2 E Window D Window Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 19

20 STEP 4. eginning at the junction of the jamb and the head, and away from the corner, cut the DuPont StraightFlash VF at a 45 angle. Repeat the procedure at the junction of the sill and jambs.. Fold cut jamb flashing parallel to the window frame so that the jamb flashing lies flat.. Fold the newly created jamb flashing flaps down at the corners and adhere to the window frame. Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 20

21 STEP 5. If sealant is applied to the sill, ensure that there are at least two (2) 2 gaps in the sealant bead to allow for drainage for every 4 of window using DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant.. Install window according to manufacturer s installation instructions.. Remove the remaining release paper from the DuPont StraightFlash VF jamb flashing and press firmly to adhere it to the exterior sheathing or framing members. D. Remove the release paper at the head and adhere it to the exterior sheathing or framing members. STEP 6 (OPTIONL). over exposed butyl with DuPont StraightFlash, DuPont Flashing Tape or DuPont Tyvek Tape.. ut a piece of metal or vinyl drip cap slightly longer than the width of the window and place a bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant on the rear side. Install the drip cap tight against brick mold and cover the top edge with DuPont StraightFlash or DuPont Flashing Tape. D INORRET DuPont FlexWrap NF reverse flashed INORRET DuPont StraightFlash flush with DuPont FlexWrap NF ORRET DuPont StraightFlash overlaps DuPont FlexWrap NF NOTE: Do not reverse shingle. DuPont StraightFlash must overlap DuPont FlexWrap NF and adhere to the substrate. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 21

22 STEP 7 Install DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant (and backer rod as necessary) around the window opening at the interior. It is also acceptable to use DuPont Window & Door Foam or recommended foam. The seal created by the sealant (and backer rod as necessary) or foam will also serve as a back dam. DuPont Residential Sealant or DuPont ommercial Sealant should be tooled flat to allow the natural curing process to create a concave shape. e sure that the sealant penetrates the grooves of the DuPont FlexWrap NF around the sill. NOTE: Installations that specify a window/door design rating of DP45 or greater require extra precautions. See General Instructions for performance requirements exceeding this design rating. STEP 8 fter installing the DuPont Tyvek WR, cut as shown to expose window and apron. (Refer to the DuPont Tyvek Water-Resistive and ir arriers Installation Guidelines to install the DuPont Tyvek WR properly). DO NOT UT THROUGH THE DUPONT FLSHING SYSTEMS PRODUTS OR PRON. Window DuPont FlexWrap NF pron made of DuPont Tyvek WR Place apron over lower layer of DuPont Tyvek WR 6 Minimum Overlap DuPont Tyvek WR SIDE VIEW DETIL DO NOT UT through DuPont Flashing Systems Products or apron. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 22

23 STEP 9 Final Step. Tape seams as shown. DO NOT TPE at bottom of window. t the head, continuous tape seams as shown with DuPont Tyvek Tape. Skip-taping at the head is acceptable if an air barrier is not required or if additional drainage is desired.. Lap bottom of apron and DuPont Tyvek WR over building materials below for proper shingling. LTERNTE TPE DETIL Place a continuous bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant around the jamb and head flashing under the DuPont Tyvek WR. Press the DuPont Tyvek WR securely into the sealant. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 23

24 rick Mold Door EFORE Water-Resistive arrier (WR) Is Installed This installation guide is intended for doors installed above grade and with wood floor construction. Method applies to the following products: DuPont StraightFlash, DuPont StraightFlash VF, DuPont FlexWrap NF, and DuPont Flashing Tape STEP 1 ttach apron made of DuPont Tyvek WR under sill (S). pron should extend at least 10 beyond sides of rough opening jambs (or to first stud in open stud construction), and far enough below the rough opening to overlap the sill plate or the DuPont Tyvek WR below. The top of the apron should be securely attached to the wall and the bottom of the apron should be left unsecured so it can overlap the DuPont Tyvek WR which will be installed after the door. 10 (S) opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 24

25 STEP 2 Preparation of sill flashing:. ut piece of DuPont FlexWrap NF at least 12 LONGER than the width of the sill (S).. DuPont FlexWrap NF has perforated release paper to help with the formation of the back dam. To ensure that the perforation tears cleanly, fold the perforation 180 and crease the flashing.. Remove the two widest pieces of release paper leaving the narrowest release paper on the flashing. When the finished floor is applied, the release paper can be removed and the back dam can be completed. 6-inch for 2x4-inch studs 9-inch for 2x6-inch studs Overlap Perf reak Perf Peel Off 2-pieces of acking opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 25

26 STEP 3 (OPTIONL K DM) Install the sill flashing as indicated leaving the 1 of DuPont FlexWrap NF with release paper extending it past the door threshold on the inside. When the 1 of release paper is removed, there should be 3/4 of flashing to form the back dam. OPTION 2: Some flooring cannot accomodate a back dam. In that case fold the 1 back dam on top of DuPont FlexWrap NF in the sill. Door will be installed on top of the 1 fold to create a back dam. EXTERIOR INTERIOR Door Door Threshold Transition Threshold Flooring Optional WRONG No Gap in orner Door Jamb DuPont FlexWrap NF Sill ORRET DuPont StraightFlash High Pressure Skirt (See Step 8 Optional) DuPont FlexWrap NF DuPont Tyvek WR Sheathing Sub Floor orner Guard (optional) DO NOT STRETH FRONT VIEW ORNER DETIL SIDE VIEW DETIL opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 26

27 STEP 4. Fan out DuPont FlexWrap NF at bottom corners onto the face of the wall. overage of DuPont FlexWrap NF should be 2 to 3 onto the face of the wall. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 27

28 STEP 5 (FOR RIK MOLD DOORS). Prepare head flashing by cutting a piece of DuPont StraightFlash VF at least twelve (12) inches LONGER than the head length.. reak the scored release paper on one edge of the head flashing by folding it back and forth upon itself.. enter the DuPont StraightFlash VF along the length of the door head and position so that it contacts the door frame and interior side of the brick mold or flange. Remove the outer release paper and adhere the flashing to the door frame. Use the inner release paper to form a tight seal in the corner. D. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. E. t the corner of the door frame, cut the DuPont StraightFlash VF at a 45 angle. F. Fold the newly created flashing flap down flat against the brick mold or flange. G. Fold remaining head flashing flaps down onto the jamb frame. D F G E Scored Release Paper utyl rick Mold Door VIEW - Door Door Door Door opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 28

29 STEP 6. Prepare jamb flashing by cutting a piece of DuPont StraightFlash VF at least six (6) inches LONGER than the jamb.. reak the scored release paper on one side of the jamb flashing by folding it back and forth upon itself. Position so that DuPont StraightFlash VF contacts the door frame and interior side of the brick mold or flange. Ensure that the jamb flashing is positioned 1-1/2 inch below the top edge of the head flashing. Jamb flashing adhesive must come in contact with head flashing adhesive by one inch. D. Remove the outer release paper and adhere the flashing to the door frame. Use the inner release paper to form a tight seal in the corner. E. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. F. Repeat on opposite jamb. STEP 7. eginning at the junction of the jamb and head and beginning at the junction of the jamb and sill, and away from the corner, cut the DuPont StraightFlash VF along both corners at a 45 angle.. Fold newly created flaps down flat against the head flashing.. Fold newly created flaps down onto the head and sill of door frame. 1-1/2 Make sure the adhesive on these pieces will overlap. 1-1/2 E Door Door Door Door Door Door D opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 29

30 FOR RIK MOLD STEP 8 (OPTIONL - HIGH PRESSURE SKIRT) For extreme weather conditions, performance requirements exceeding STM E1677, or window/door design ratings of DP45 or greater, see General Instructions.. reate the high pressure skirt by cutting a piece of DuPont Tyvek WR 1 wider than the width of the door opening and approximately 10 in height.. ut a piece of DuPont StraightFlash VF to the same width of skirt. Remove release paper from one side of DuPont StraightFlash VF and adhere to DuPont Tyvek WR. The skirt may be made with DuPont StraightFlash VF, DuPont StraightFlash or DuPont Flashing Tape.. Remove the release paper from the other side of DuPont StraightFlash VF and adhere the butyl adhesive at the sill skirt to the underside of the door threshold behind the jamb flashing. D. Secure edges of the optional skirt with two 4 pieces of DuPont StraightFlash or DuPont Flashing Tape. E. Tape the bottom of the optional skirt to allow for drainage and to minimize wind damage during construction. F. If sealant is applied to the sill, insure (2) 2 gaps to allow for drainage for every 4 of door using DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant. DuPont StraightFlash VF utyl dhesive 10 Peel Off Release Paper and attach to underside of door F D Optional High Pressure Skirt D E opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 30

31 STEP 9. Install door according to manufacturer s installation instructions.. Remove the remaining release paper from the DuPont StraightFlash VF jamb flashing and press firmly to adhere it to the exterior sheathing or framing members.. Remove the release paper at the head and adhere it to the exterior sheathing or framing members. OPTIONL: over exposed butyl with DuPont StraightFlash, DuPont Flashing Tape or DuPont Tyvek Tape. STEP 10 (OPTIONL). ut a piece of metal or vinyl drip cap slightly longer than the width of the door and place a bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant on the rear side. Install the drip cap tight against the door head and cover the top edge with DuPont StraightFlash or DuPont Flashing Tape. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 31

32 STEP 11 fter installing the DuPont Tyvek WR, cut as shown to expose door and apron. (Refer to the DuPont Tyvek Water-Resistive and arriers Installation Guidelines to install the DuPont Tyvek WR properly). DO NOT UT THROUGH THE DUPONT FLSHING SYSTEMS PRODUTS OR PRON. STEP 12. Tape seams as shown. DO NOT TPE at bottom of window. t the head, continuous tape seams as shown with DuPont Tyvek Tape. Skip-taping at the head is acceptable if an air barrier is not required or if additional drainage is desired.. Lap bottom of apron and the DuPont Tyvek WR over building materials below for proper shingling. DO NOT UT through DuPont Flashing Systems Products or apron. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 32

33 LTERNTE TPE DETIL Place a continuous bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant around the jamb and head flashing under the DuPont Tyvek WR. Press the DuPont Tyvek WR securely into the sealant. STEP 13 Final Step. When the interior flooring is ready to install, remove release paper and use Folding Option One or Two to form back dam.. Install DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant (and backer rod as necessary) around the window opening at the interior. It is also acceptable to use DuPont Window & Door Foam or recommended foam. The seal created by the sealant (and backer rod as necessary) or foam will also serve as a back dam. DuPont Residential Sealant or DuPont ommercial Sealant should be tooled flat to allow the natural curing process to create a concave shape. e sure that the sealant penetrates the grooves of the DuPont FlexWrap NF around the sill. NOTE: Installations that specify a window/door design rating of DP45 or greater require extra precautions. See General Instructions for performance requirements exceeding this design rating. Folding Option One Folding Option Two OR Fold Out and Up Fold In and Up Fastening Option One Fastening Option Two OR Staples Tape opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 33

34 Field pplied Flanged Window EFORE Water-Resistive arrier (WR) Is Installed Method applies to the following products: DuPont StraightFlash, DuPont StraightFlash VF, DuPont FlexWrap NF and DuPont Flashing Tape STEP 1. ttach apron made of DuPont Tyvek WR under sill (S). pron should extend at least 10 beyond sides of rough opening jambs (or to first stud in open stud construction), and far enough below the rough opening to overlap the sill plate or the DuPont Tyvek WR below. The top of the apron should be securely attached to the wall and the bottom of the apron should be left unsecured so it can overlap the DuPont Tyvek WR which will be installed after the window.. ut DuPont FlexWrap NF at least 12 longer than width of sill rough opening (S).. Remove first piece of release paper, cover horizontal sill by aligning inside edge of sill, and adhere into rough opening across sill and up jambs (min. 6 on each side). D. Remove second release paper. E. Fan out DuPont FlexWrap NF at bottom corners onto the face of the wall. overage of DuPont FlexWrap NF should be 2 to 3 onto the face of the wall. No Gap in orner Door Jamb DuPont FlexWrap NF WRONG Sill ORRET (S) 4 FRONT VIEW ORNER DETIL 10 Sill Width + 12 inches 6 Minimum DO NOT STRETH E opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 34

35 STEP 2. pply field applied flanges in the correct shingling fashion per manufacturer s installation instructions. DO NOT REVERSE SHINGLE.. ut four 3 x 3 pieces of DuPont FlexWrap NF.. pply DuPont FlexWrap NF patches to back of flange corners before applying DuPont StraightFlash VF. D. Staple patches in corners and secure to wooden head and jambs. 1 Field pplied Flanges Exterior Exterior D 2 Note Proper Shingling x3 DuPont FlexWrap NF opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 35

36 STEP 3. Prepare head flashing by cutting a piece of DuPont StraightFlash VF at least twelve (12) inches LONGER than the head length.. reak the scored release paper on one side of the head flashing by folding it back and forth upon itself.. enter the DuPont StraightFlash VF along the length of the window head and position so that it contacts the window frame and interior side of the brick mold or flange. Remove the outer release paper and adhere the flashing to the window frame. Use the inner release paper to form a tight seal in the corner. D. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. E. eginning at the junction of the jamb and the head, and away from the corner, cut DuPont StraightFlash VF at a 45 angle. F. Fold the newly created flaps down against the brick mold or flange. G. Fold remaining head flashing flaps down onto the jamb. Field pplied Flange Window D E Scored Release Paper utyl F G VIEW - Window Window Window Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 36

37 STEP 4. Prepare jamb flashing by cutting a piece of DuPont StraightFlash VF at least six (6) inches LONGER than the jamb.. reak the scored release paper on one side of the jamb flashing by folding it back and forth upon itself. Position so that the DuPont StraightFlash VF contacts the window frame and interior side of the brick mold or flange. Ensure that the jamb flashing is positioned 1-1/2 inch below the top edge of the head flashing. Jamb flashing adhesive must come in contact with head flashing adhesive and overlap one inch. D. Remove the outer release paper and adhere the flashing to the window frame. Use the inner release paper to form a tight seal in the corner. E. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. F. Repeat on opposite jamb. Make sure the adhesive on these pieces will overlap. 1-1/2 E Window D Window Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 37

38 STEP 5. eginning at the junction of the jamb and head, and away from the corner, cut the DuPont Straightflash VF at a 45 angle. Repeat the procedure at the junction of the sill and jamb.. Fold cut jamb flashing parallel to the window frame so that the jamb flashing lies flat.. Fold remaining jamb flashing flaps down at all corners and adhere to the window frame. STEP 6. If sealant is applied to the sill, ensure that there are at least two (2) 2 gaps in the sealant bead to allow for drainage for every 4 of window using DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant.. Install window according to manufacturer s installation instructions.. Remove the remaining release paper from the DuPont StraightFlash VF jamb flashing and press firmly to adhere it to the exterior sheathing or framing members. D. Remove the release paper at the head and adhere it to the exterior sheathing or framing members. D Window opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 38

39 STEP 6 (OPTIONL). over exposed butyl with DuPont StraightFlash, DuPont Flashing Tape or DuPont Tyvek Tape.. ut a piece of metal or vinyl drip cap slightly longer than the width of the window and place a bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant on the rear side. Install the drip cap tight against brick mold and cover the top edge with DuPont StraightFlash or DuPont Flashing Tape. STEP 7 Install DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant (and backer rod as necessary) around the window opening at the interior. It is also acceptable to use DuPont Window & Door Foam or recommended foam. The seal created by the sealant (and backer rod as necessary) or foam will also serve as a back dam. DuPont Residential Sealant or DuPont ommercial Sealant should be tooled flat to allow the natural curing process to create a concave shape. e sure that the sealant penetrates the grooves of the DuPont FlexWrap NF around the sill. NOTE: Installations that specify a window/door design rating of DP45 or greater require extra precautions. See General Instructions for performance requirements exceeding this design rating. INORRET DuPont FlexWrap NF reverse flashed INORRET DuPont StraightFlash flush with DuPont FlexWrap NF ORRET DuPont StraightFlash overlaps DuPont FlexWrap NF NOTE: Do not reverse shingle. DuPont StraightFlash must overlap DuPont FlexWrap NF and adhere to the substrate. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 39

40 STEP 8 fter installing the DuPont Tyvek WR, cut as shown to expose door and apron. (Refer to the DuPont Tyvek Water-Resistive arriers Installation Guidelines to install the DuPont Tyvek WR properly). DO NOT UT THROUGH THE DUPONT FLSHING SYSTEMS PRODUTS OR PRON. STEP 9 Final Step. Tape seams as shown. DO NOT TPE at bottom of window. t the head, continuous tape seams as shown with DuPont Tyvek Tape. Skip-taping at the head is acceptable if an air barrier is not required or if additional drainage is desired.. Lap bottom of apron and DuPont Tyvek WR over building materials below for proper shingling. Window DuPont FlexWrap NF pron made of DuPont Tyvek WR Place apron over lower layer of DuPont Tyvek WR 6 Minimum Overlap DuPont Tyvek WR SIDE VIEW DETIL DO NOT UT through DuPont Flashing Systems Products or apron. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 40

41 LTERNTE TPE DETIL Place a continuous bead of DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant around the jamb and head flashing under the DuPont Tyvek WR. Press the DuPont Tyvek WR securely into the sealant. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 41

42 Field pplied Flanged Door EFORE Water-Resistive arrier (WR) Is Installed This installation guide is intended for doors installed above grade and with wood floor construction. Method applies to the following products: DuPont StraightFlash, DuPont StraightFlash VF, DuPont FlexWrap NF, and DuPont Flashing Tape STEP 1 ttach apron made of DuPont Tyvek WR under sill (S). pron should extend at least 10 beyond sides of rough opening jambs (or to first stud in open stud construction), and far enough below the rough opening to overlap the sill plate or the DuPont Tyvek WR below. The top of the apron should be securely attached to the wall and the bottom of the apron should be left unsecured so it can overlap the DuPont Tyvek WR which will be installed after the door. 10 (S) opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 42

43 STEP 2 Preparation of sill flashing:. ut piece of DuPont FlexWrap NF at least 12 LONGER than the width of the sill (S).. DuPont FlexWrap NF has perforated release paper to help with the formation of the back dam. To ensure that the perforation tears cleanly, fold the perforation 180 and crease the flashing.. Remove the two widest pieces of release paper leaving the narrowest release paper on the flashing. When the finished floor is applied, the release paper can be removed and the back dam can be completed. Front 6-inch for 2x4-inch studs 9-inch for 2x6-inch studs Overlap Scored Release Paper ack reak Scored Release Paper Peel Off 2-pieces of Release Paper opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 43

44 STEP 3 (OPTIONL KDM) Install the sill flashing as indicated leaving the 1 of DuPont FlexWrap NF with release paper extending it past the door threshold on the inside. When the 1 of release paper is removed, there should be 3/4 of flashing to form the back dam. OPTION 2: Some flooring cannot accomodate a back dam. In that case fold the 1 back dam on top of DuPont FlexWrap NF in the sill. Door will be installed on top of the 1 fold to create a back dam. EXTERIOR INTERIOR Door Door Threshold Transition Threshold Flooring Optional WRONG No Gap in orner Door Jamb DuPont FlexWrap NF Sill ORRET DuPont StraightFlash High Pressure Skirt (See Step 9 Optional) DuPont FlexWrap NF DuPont Tyvek WR Sheathing Sub Floor orner Guard (optional) DO NOT STRETH FRONT VIEW ORNER DETIL SIDE VIEW DETIL opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 44

45 STEP 4. Fan out DuPont FlexWrap NF at bottom corners onto the face of the wall. overage of DuPont FlexWrap NF should be 2 to 3 onto the face of the wall. opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 45

46 STEP 5 (FOR FIELD PPLIED FLNGED DOORS ONLY) NOTE: This step is not required for rick Mold Doors. pply field applied flanges in the correct shingling fashion per manufacturer s installation instructions. DO NOT REVERSE SHINGLE.. ut four 3 x 3 pieces of DuPont FlexWrap NF.. pply DuPont FlexWrap NF patches to back of flange corners before applying DuPont StraightFlash VF. D. Staple patches in corners and secure to wooden head and jambs. 1 Field pplied Flanges Exterior Exterior 2 D Note Proper Shingling DuPont FlexWrap 3 3 x 3 DuPont FlexWrap NF 4 opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 46

47 STEP 6 (FOR FIELD PPLIED DOORS). Prepare head flashing by cutting a piece of DuPont StraightFlash VF at least twelve (12) inches LONGER than the head length.. reak the scored release paper on one edge of the head flashing by folding it back and forth upon itself.. enter the DuPont StraightFlash VF along the length of the door head and position so that it contacts the door frame and interior side of the brick mold or flange. Remove the outer release paper and adhere the flashing to the door frame. Use the inner release paper to form a tight seal in the corner. D. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. E. t the corner of the door frame, cut the DuPont StraightFlash VF at a 45 angle. F. Fold the newly created flashing flap down flat against the brick mold or flange. G. Fold remaining head flashing flaps down onto the jamb frame. D E F G Field pplied Flange Window Scored Release Paper utyl VIEW - Door Door Door Door opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 47

48 STEP 7. Prepare jamb flashing by cutting a piece of DuPont StraightFlash VF at least six (6) inches LONGER than the jamb.. reak the scored release paper on one side of the jamb flashing by folding it back and forth upon itself. Position so that DuPont StraightFlash VF contacts the door frame and interior side of the brick mold or flange. Ensure that the jamb flashing is positioned 1-1/2 inch below the top edge of the head flashing. Jamb flashing adhesive must come in contact with head flashing adhesive by one inch. D. Remove the outer release paper and adhere the flashing to the door frame. Use the inner release paper to form a tight seal in the corner. E. Remove the inner release paper and adhere the flashing to the back of the brick mold or flange. F. Repeat on opposite jamb. STEP 8. eginning at the junction of the jamb and head and beginning at the junction of the jamb and sill, and away from the corner, cut the DuPont StraightFlash VF along both corners at a 45 angle.. Fold newly created flaps down flat against the head flashing.. Fold newly created flaps down onto the head and sill of door frame. 1-1/2 Make sure the adhesive on these pieces will overlap. 1-1/2 E Door Door Door Door Door Door D opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 48

49 FOR RIK MOLD, FIELD PPLIED ND NON-FLNGED DOORS STEP 9 (OPTIONL) - HIGH PRESSURE SKIRT For extreme weather conditions, performance requirements exceeding STM E1677, or window/door design ratings of DP45 or greater, see General Instructions.. reate the high pressure skirt by cutting a piece ofdupont Tyvek WR 1 wider than the width of door opening and approximately 10 in height.. ut a piece of DuPont StraightFlash VF to the same width of skirt. Remove release paper from one side of DuPont StraightFlash VF and adhere to DuPont Tyvek WR. The skirt may be made with DuPont StraightFlash VF, DuPont StraightFlash or DuPont Flashing Tape.. Remove the release paper from the other side of DuPont StraightFlash VF and adhere the butyl adhesive at the sill skirt to the underside of the door threshold behind the jamb flashing. D. Secure edges of the optional skirt with two 4 pieces of DuPont StraightFlash or DuPont Flashing Tape. E. Tape the bottom of the optional skirt to allow for drainage and to minimize wind damage during construction. F. If sealant is applied to the sill, insure (2) 2 gaps to allow for drainage for every 4 of door using DuPont Residential Sealant, DuPont ommercial Sealant, or recommended sealant. DuPont StraightFlash VF utyl dhesive 10 Peel Off Release Paper and attach to underside of door F D Optional High Pressure Skirt D E opyright 2011 E. I. du Pont de Nemours and ompany. ll Rights Reserved. Rev. 10/11 49