Installing Microsoft Windows Server 2008R2 with EasyStartup

Transcription

1 Installing Microsoft Windows Server 2008R2 with EasyStartup Version 1.5 1/11/2013 LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON- INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This information could include technical inaccuracies or typographical errors. Changes may be made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. Copyright Lenovo The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo, EasyStartup, and ThinkServer. Windows Server 2012 is a trademark of Microsoft in the United States and/or other countries.

2 Contents Introduction... 3 Determining the IP address of the BMC/TMM... 3 Turning off PXE Boot... 4 Connecting to the BMC/TMM... 5 RAID configuration with EasyStartup... 7 Microsoft Windows Server 2008 installation with EasyStartup

3 Introduction This document will take you step by step through installing Microsoft Windows Server 2008 on a ThinkServer using EasyStartup. This document applies to the TS430, RD330, RD430, RD530, and RD630. All screen shots apply to all systems except where noted. Determining the IP address of the BMC/TMM This must be done with a monitor and keyboard attached to the server. The operation shown is for TS430. 1) Enter Setup 2) Go to Server Management Select BMC LAN Configuration 3) IP address is the address of the BMC/TMM 3

4 Turning off PXE Boot The operation shown is for TS430. 4) Enter Setup 5) This is the Main Tab 6) Go to the Advanced Tab Select PCI Configuration 7) Set Onboard LAN #1 I/O ROM and Onboard I/O ROM to [Disabled] 4

5 Connecting to the BMC/TMM 8) Open a Web Browser 9) Enter the IP address of the BMC/TMM 10) The default login is: Username:lenovo Password:lenovo 11) Go to Remote Control Launch section and press the Launch Java KVM Client 12) If Launch Java KVM Client is grayed out Go to Remote Control Configuration section and enable Virtual KVM 5

6 13) You will recive this security warning Accept it and press Run 14) The Video Viewer will launch 6

7 RAID configuration with EasyStartup The operation shown is for TS430. 1) Boot to the EasyStartup DVD 2) Set the language 7

8 3) Agree to the End User License Agreement 4) Set the Data and Time 5) Select Continue to the main interface 8

9 6) Select Configure RAID 7) Select the RAID controller you want to configure. Press Next. 8) Select Create new configuration. Press Next. 9

10 9) This will delete any configured arrays attached to the selected controller Press Yes. 10) Select the drives to be added to the new configuration. Press Next. 11) Select the RAID level for the new configuration. Press Next. 10

11 12) Set the advanced settings for the new configuration. Press Next. 13) Verify that the settings are correct. Press Next. 14) Once the progress bar is complete the RAID array will be created and configured as a boot device. Once completed press Next. 11

12 15) If you would like to save this configuration to a response file select Yes and complete the steps to save the file. If not select No and press Next. 16) Select Reboot now and press Next. 12

13 Microsoft Windows Server 2008 installation with EasyStartup 1) Boot to the EasyStartup DVD 2) Set the language 3) Agree to the End User License Agreement 13

14 4) Set the Data and Time 5) Select Continue to the main interface Press OK 6) Select Install operating system 14

15 7) Select Microsoft Windows Server 2008R2 x64/hyperv 2008R2. Press Next The OSs listed are all the OSs supported by EasyStartup on the platform 8) Select the disk to install the OS to. Press Next 9) Select the partition options for the install. Press Next 15

16 10) Set the Partition setting. Press Next 11) Enter the Installation settings. Your full name: Organization: Computer name: Time zone: Product key: Administrator password: Press Next 12) Enter the Network Settings. Domain name: Domain administrator account: Domain administrator password: Workgroup: Eithernet controller: IP address: Subnet mask: Default gateway: DNS Settings: WINS Settings: Press Next 16

17 13) Select the additional application to install. Press Next 14) Select the additional Windows components to install. Press Next 15) Confirm the settings Press Next. 17

18 16) If you would like to save this configuration to a response file select Yes and complete the steps to save the file. If not select No and press Next. 17) Press Next 18) Press Yes 18

19 19) The progress will start to build 20) The EasyStartup DVD will automaticly be ejected. Insert the Windows Server 2008 install media into the drive and press OK. 21) Select the version of the OS to install. Press OK 19

20 22) Agree to the End User License Agreement. 23) EasyStartup will copy all files need for the installation. 24) EasyStartup will eject the install media and reboot as needed. Remove the DVD from the drive. 25) The server will reboot multipul times on its own. 26) Once the server boots into the OS and shows the properties screen of Windows it has completed the installation. 20