RSA SecurID Soft token. Cisco Anyconnect SSL VPN client. Connection guide: SSL VPN. SSL VPN (Soft token) First time user or after PIN reset

Transcription

1

2

3 Table of Contents Installation Guide RSA SecurID Soft token Cisco Anyconnect SSL VPN client Connection guide: SSL VPN SSL VPN (Soft token) First time user or after PIN reset Non first-time user

4 Installation Guide

5 RSA SecurID Soft token Section Applicable to RSA SecurID Version Supported platforms Disk requirements Pre-requisites Technical Support Details FXA Office employees V Windows XP SP2 and SP3 Windows 7 32-bit and 64-bit 30 MB (Windows) RSA SecurID seed token file (.stdid) from System Account Management (SAM) team. This file is sent by RSD/ODT in zipped file via Seed token file (stdid): System Account Management (SAM) Ext 5393 RSA SecurID Token Client: RSD Ext 5393 Step Procedure details 1 Close and save all Windows applications. Windows: Unzip RSASecurIDToken410.zip and run RSASecurIDToken410.msi installation file Click Next to continue 2 Select You ordered this RSA product from Europe, Africa or Asia Pacific and accept the license agreement.

6 Select Custom setup type and select Browser Plug-ins to be installed at local hard drive. Click Install button to commence the installation. Tick Launch RSA SecurID Software Token and Click Finish. 3 The application will be launched automatically OR run it manually from: Windows XP: Start > Programs > RSA SecurIDToken > RSA SecurID Token Windows 7: Start > All Programs > RSA SecurID Token > RSA SecurID Token Click Import from File icon and Browse

7 Click Import from File icon and Browse button. Select *.stdid file. And press OK Click Change Name button and input Employee number (eg. Auxxxxxxxx) and click OK RSA SecurID main screen will appear after successful installation. 4 Note: If the.stdid (seed) file isn t imported properly, the UserID won t appear on the top left screen side. You can re-import it again via Option > Import token and follow step 4 again.

8 Cisco Anyconnect SSL VPN client Section Applicable to Details FXA Employees Cisco SSL Version Software location 1 Software location 2 Software location 3 Supported platforms Run Advertised Programs (Control Panel) ftp://ftp.fxa.com.au/software/vpn/cisco%20anyconnect%20ssl%20vpn% 20client/Windows/anyconnect-win pre-deploy-k9.msi Windows XP SP2/SP3 SOE Windows 7 32-bit/64-bit SOE Technical support System Account Management (SAM) Ext 5393 Step Procedure details 1 Close and save all Windows applications. Run: anyconnect-win pre-deploy-k9.msi file and follow the instructions. 2

9

10 Connection guide: SSL VPN

11 SSL VPN (Soft token) First time user or after PIN reset Step Details 1 2 Connect to Wireless SSID network: FXA-Wireless Run Cisco Anyconnect VPN client via: Start > Programs > Cisco > Cisco Anyconnect Secure Mobility Client 3 Click: button Untick Block connections to untrusted servers Click Exit button 4 Connect to: vpn1.fxa.com.au/fxavpn128 Click Connect button 5 A dialog box may be prompted:

12 Click Connect Anyway button [Your FXA AD username] [4-8 digits PIN or 8-digits rotating RSA Passcode] 6 7

13 [Your FXA AD username] [4-8 digits PIN or 8-digits rotating RSA Passcode] 8 A second warning page may be displayed: 9 Click Connect Anyway button When you re successfully connected to VPN, the following confirmation page will be displayed: 10

14 Non first-time user Step Details 1 2 Connect to Wireless SSID network: FXA-Wireless Run Cisco Anyconnect VPN client via: Start > Programs > Cisco > Cisco Anyconnect Secure Mobility Client 3 Click: button Untick Block connections to untrusted servers Click Exit button 4 Connect to: vpn1.fxa.com.au/fxavpn128 Click Connect button 5 A dialog box may be prompted:

15 Click Connect Anyway button [Your FXA AD username] [4-8 digits PIN or 8-digits rotating RSA Passcode] 6 8 A second warning page may be displayed: 9 Click Connect Anyway button When you re successfully connected to VPN, the following confirmation page will be displayed: 10