DG2706. High Speed, Low Voltage, 3, Quad SPDT CMOS Analog Switch. Vishay Siliconix DESCRIPTION FEATURES APPLICATIONS

Transcription

1 High Speed, Low Voltage, 3, Quad SPDT CMOS Analog Switch DESCRIPTION The DG2706 is a high speed, low voltage, low On-resistance, quad SPDT (single pole double throw) analog switch. It operates from a.6 V to 4.3 V single power supply and achieves 3 switch On-resistance. When turned on, each switch conducts equally in both directions. Its switch on resistance flatness is 0.6 and channel to channel matching is of 0.3 when powered with single 3. V supply. All channels guaranteed break before make switching. Control logic input has 0. V to.6 V logic threshold. It features a 90 MHz - 3 db bandwidth, - 90 db crosstalk and - 70 db off-isolation at MHz. The DG2706 is an ideal fit for low voltage battery powered devices switching audio, video, multi-media data streams, and control signals between different functional circuits or ports. The DG2707 comes in a small miniqfn-6 lead package (.8 mm x 2.6 mm x 0.7 mm). As a committed partner to community and the environment, manufactures this product with the lead(pb)-free device terminations and is 00 % RoHS compliant. FEATURES Operation voltage range:.6 V to 4.3 V Guaranteed On-resistance: 3.0 at 3. V Low voltage logic threshold Low crosstalk: - 70 db High off-isolation: - 90 db Ultra small package: miniqfn6 of.8 mm x 2.6 mm APPLICATIONS Dual SIM card switch A/V and analog signal routing Battery operated devices Data acquisition systems Communications systems Medical and ATE equipments FUNCTIONAL BLOCK DIAGRAM AND P CONFIGURATION miniqfn-6l NO4 NC NC4 NO 4 VXX 7 6 NO3 NC Pin : LONG LEAD NC 2 NO2 Device Marking: VXX Traceability Code: V is DG2706DN XX = Date/Lot Top View ORDERG FORMATION Temp. Range Package Part Number - 40 C to 8 C miniqfn-6 DG2706DN-T-E4 S-076-Rev. B, 07-Feb-

2 TRUTH TABLE DG2706 QUAD SPDT, miniqfn-6l Select Input On Switches (Pin 0) 2 (Pin 3) Description (Pin) Common (Pin) 0 X NC (Pin ) (Pin 6) X NO (Pin ) 0 X NC4 (Pin 4) 4 (Pin 3) X NO4 (Pin 2) 0 NC2 (Pin 6) X 2 (Pin ) NO2 (Pin 4) 0 NC3 (Pin 9) X 3 (Pin 3) NO3 (Pin 7) ABSOLUTE MAXIMUM RATGS (T A = 2 C, unless otherwise noted) Parameter Limit Unit Reference to to.0,, NC, NO a to ( + 0.3) V Current (Any terminal except NO, NC or ) 30 Continuous Current (NO, NC, or ) ± 20 ma Peak Current (Pulsed at ms, 0 % Duty Cycle) ± 00 Storage Temperature (D Suffix) - 6 to 0 C Thermal Resistance (Package) b miniqfn-6 2 C/W Power Dissipation (Package) b miniqfn-6 c, d 2 mw Notes: a. Signals on NC, NO, or or exceeding will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to PC board. c. Derate 6.6 mw/ C above 70 C d. Manual soldering with iron is not recommended for leadless components. The miniqfn-6 is a leadless package. The end of the lead terminal is exposed copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper lip cannot be guaranteed and is not required to ensure adequate bottom side solder interconnection. 2 S-076-Rev. B, 07-Feb-

3 SPECIFICATIONS ( = 3. V) Parameter Symbol Test Conditions Otherwise Unless Specified Temp. b Limits - 40 C to 8 C Min. d Typ. c Max. d Analog Switch Analog Signal Range e V ANALOG R DS(on) Full 0 V On-Resistance R DS(on) = 3. V, I NO/NC = 0 ma, V =.0 V Room 3. Full 6 R ON Match R (ON) = 3. V, I NO/NC = 0 ma, V =.0 V Room 0.3 R ON Resistance Flatness R ON = 3. V, I NO/NC = 0 ma, Room 0.6 Channel Off Leakage Current I NO/NC(off) = 3.6 V, V NO/NC = 0. V/3 V, Room Full I (off) V = 3 V/0. V Room - Full Channel-On Leakage Room I Current (on) = 3.6 V, V NO/NC, V = 3 V/0. V Full Digital Control Input High Voltage V H Full.6 Input Low Voltage V L Full 0.4 V Input Current I L or I H V = 0 or Full - µa Dynamic Characteristics Break-Before-Make Time t BBM Room Full Room 20 4 Enable Turn-On Time t ON(EN) V NO, V NC =. V, R L = 0, C L = 3 pf Full ns Room 3 Enable Turn-Off Time t OFF(EN) Full 4 Charge Injection d Q J C L = nf, R GEN = 0, V NC/NO = 2 V Room 3 pc Off-Isolation d OIRR Room - 70 = 3. V, f = MHz, R L = 0, C L = pf Crosstalk d, f X TALK Room - 90 db Bandwidth d BW = 3. V, R L = 0, C L = pf, - 3 db Room 90 MHz Total Harmonic Distortion d THD = 3. V, R LOAD = 600 Room 0.02 % N O, N C Off Capacitance d CS NC(off) 6 CS NO(on) = 3. V, f = MHz Room pf Channel-On Capacitance d C (on) 3 Power Supply Power Supply Range V Power Supply Current I+ V = 0 or Full µa Notes: a. Room = 2 C, Full = as determined by the operating suffix. b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. c. Typical values are for design aid only, not guaranteed nor subject to production testing. d. Guarantee by design, not subjected to production test. e. V = input voltage to perform proper function. f. Crosstalk measured between channels. Unit na Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. S-076-Rev. B, 07-Feb- 3

4 TYPICAL CHARACTERISTICS (T A = 2 C, unless otherwise noted) RON - On-Resistance (Ω) =.6 V T = 2 C I ON = 0 ma R ON - On-Resistance (Ω) =.6 V, I ON = 0 ma + 8 C + 2 C - 40 C 6 4 = 3. V = 3.6 V V D - Analog Voltage (V) R ON vs. V D and Single Supply Voltage V D - Analog Voltage (V) R ON vs. Analog Voltage and Temperature = 3. V, I ON = 0 ma 0 DG2706 R L = 600 Ω V Signal = V RMS R ON - On-Resistance (Ω) C + 2 C - 40 C THD (%) =.6 V = 3.6 V = 3. V V D - Analog Voltage (V) R ON vs. Analog Voltage and Temperature Frequency (Hz) Switching Threshold vs. Supply Voltage = 3.6 V, I ON = 0 ma 0 ma ma R ON - On-Resistance (Ω) C + 8 C + 2 C I+ - Supply Current (A) 00 µa 0 µa µa 00 na 0 na = 3.6 V = 3. V =.6 V na V D - Analog Voltage (V) R ON vs. Analog Voltage and Temperature 00 pa 0 00 K 0K 00K M 0M Input Switching Frequency (Hz) Supply Current vs. Input Switching Frequency 4 S-076-Rev. B, 07-Feb-

5 TYPICAL CHARACTERISTICS (T A = 2 C, unless otherwise noted) Leakage Currrent (pa) = 3. V I NO/NC(off) I (on) I (off) Temperature ( C) Leakage Current vs. Temperature Loss, OIRR, X TALK (db) = 3. V R L = 0 Ω OIRR Loss X TALK K M 0M 00M G Frequency (Hz) Insertion Loss, Off-Isolation Crosstalk vs. Frequency..4 VT - Switching Threshold (V) Supply Voltage (V) Switching Threshold vs. Supply Voltage S-076-Rev. B, 07-Feb-

6 TEST CIRCUITS Switch Input Logic Input NO or NC Switch Output R L 0 Ω V OUT C L 3 pf Logic Input Switch Output V H V L 0 V 0 % t r t f < ns < ns 0.9 x V OUT 0 V t ON t OFF C L (includes fixture and stray capacitance) ( ) R V OUT = V L R + L R ON Logic "" = Switch on Logic input waveforms inverted for switches that have the opposite logic sense. Figure. Switching Time Logic Input V H t r < ns t f < ns V NO NO V O V L V NC NC R L 0 Ω C L 3 pf V NC = V NO V O 90 % Switch Output 0 V t D t D C L (includes fixture and stray capacitance) Figure 2. Break-Before-Make Interval V gen + R gen V = 0 - NC or NO V OUT C L = nf V OUT On ΔV OUT Off On Q = ΔV OUT x C L depends on switch configuration: input polarity determined by sense of switch. Figure 3. Charge Injection 6 S-076-Rev. B, 07-Feb-

7 TEST CIRCUITS 0 nf 0 nf NC or NO 0 V, 2.4 V R L 0 V, 2.4 V NC or NO Meter HP492A Impedance Analyzer or Equivalent Analyzer Off Isolation V = 20 log V NO /NC f = MHz Figure 4. Off-Isolation Figure. Channel Off/On Capacitance maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see /ppg? S-076-Rev. B, 07-Feb- 7

8 Package Information MI QFN-6L (3) (4) () (6) (2) () D (0) (9) (8) (7) (6) () E L (6) () (4) (3) () (2) (3) (4) () (6) (7) (8) BACK SIDE VIEW A L () (2) (3) (4) (2) () (0) (9) A b C e DIM MILLIMETERS CHES M. NAM MAX. M. NAM MAX. A A b C D 2.60 BSC BSC E.80 BSC BSC e 0.40 BSC 0.07 BSC L L ECN T Rev. A, 4-Aug-06 DWG: 94 Document Number: Aug-06

9 PAD Pattern REMENDED MIMUM PADS FOR MI QFN 6L 0.62 (0.022) (0.07) 0.22 (0.0089) (0.42) (0.082).200 (0.0472) 2.00 (0.0827) Mounting Footprint Dimensions in mm (inch) Document Number: 667 Revision: 0-Mar-0

10 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 20/6/EU of The European Parliament and of the Council of June 8, 20 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/9/EC. We confirm that all the products identified as being compliant to Directive 2002/9/EC conform to Directive 20/6/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC definition. We confirm that all the products identified as being compliant to IEC conform to JEDEC JS709A standards. Revision: 02-Oct-2 Document Number: 9000