CIR. Index. Gexol. Standard CIR UL Listed Type TC-ER. Crush and Impact Resistant Without External Armoring. Arctic CIR UL Listed Type TC-ER-HL*

Transcription

1

2 Gexol CIR Crush and Impact Resistant Without External Armoring Passes the same stringent crush and impact testing required by UL 2225 for Type MC-HL n Available in Standard and Arctic Grade Jackets n Highly flexible Index Standard CIR UL Listed Type TC-ER CIR Power Cables Three & Four Conductor + Ground CIR Control Cable Multi-Conductor... 4 CIR Instrumentation Cables Individually Shielded Pairs... 5 Individually Shielded Triads... 5 Arctic CIR UL Listed Type TC-ER-HL* CIR Type VFD Cable Three Conductor CIR Power Cables Three & Four Conductor + Ground CIR Control Cable Multi-Conductor CIR Instrumentation Cables Individually Shielded Pairs Individually Shielded Triads Stranding Profile / Cable Color Codes Installed Cost Comparison...13 Nexans AmerCable believes the information presented throughout this catalog to be reliable and current. All information is subject to change without notice. The information listed is approximate, and is presented only as a guide for product selection. We make no claims or warranties for the suitability of any product for any particular application. AmerCable and Gexol are registered trademarks of AmerCable Incorporated. Registered in the U.S. Patent and Trademark Office AmerCable Incorporated

3 About CIR Cables Nexans AmerCable s CIR is a next-generation cable designed to replace older-technology cables like Type MC. AmerCable CIR has been successfully used globally since 2002 for mission-critical equipment operating in harsh environments. CIR passes the same stringent crush and impact tests required by UL 2225 for Type MC-HL without the use of external armoring. This highly robust cable offers significant advantages over Type MC for many industrial and mining applications, including: n MSHA Approved (Standard CIR) 3 & 4 conductor power cables n UL Listed as Type TC-ER (Standard CIR) suitable for a variety of uses, including those where tray cables are not practical or cost-prohibitive. n UL Listed as Type TC-ER-HL (Arctic Grade CIR) suitable for a variety of uses in Class 1, Div 1 and Zone 1 environments including those where tray cables are not practical or cost-prohibitive. (Cables up to 1 in OD) n Insulated with Gexol Nexans AmerCable s exclusive insulating compound provides superior flexibility, dielectric properties and field proven performance in the most severe, isolated operating environments. n Highly flexible unlike Type MC, CIR is flexible for easier installation. The cable can also be reused during an upgrade or retrofit. n Smaller bend radius up to 40% smaller than Type MC n Reduced tray fill up to 35% less compared to Type MC n Gas & vapor tight impervious to water and air n Ergonomically Superior from an ergonomic perspective, CIR is safer to handle for workers and much simpler to prepare for termination. Bend Radius Type CIR IEEE 45 6X Diameter NEC < 1" (25mm) 4X Diameter > 1" (25mm) < 2" (50mm) 5X Diameter > 2" (50mm) 6X Diameter Faster and Easier to Install than Metal Clad CIR is the fastest, safest crush-proof cable to install. Metal clad cable installation requires an expensive box of tools and a multi-step procedure for jacket removal. See page 13 for Total Installed Cable Cost 1

4 CIR Standard CIR Power Cable UL Listed as Type TC-ER Three & Four Conductor + Ground Gexol Insulated 0.6/1kV MSHA Approved Rated 90 C Insulation GEXOL cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA V/IEC 1000V. Safer to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors See Bend Radius on Page 1 Conductor Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoplastic compound meeting UL 1309/ CSA 245 and IEEE Application Designed and constructed to be a flexible alternative to Type MC cable where user desires the added crush and impact protection. Features n MSHA approved (3 & 4 conductor cables)) n Passes the same stringent crush and impact testing required by UL 2225 for Type MC-HL n Gas & vapor tight impervious to water and air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC Standard CIR Ratings & Approvals n 90 C temperature rating n UL Listed as Type TC-ER (E123629) n MSHA Approved (3 & 4 conductor cables) n UL Listed as Marine Shipboard Cable (E111461) n American Bureau of Shipping (ABS) (99-BT5905-X) n Flame Retardant IEEE 1202 n Suitable for use in Class I, Div 2 and Zone 2 environments 2 Industrial Applications: industrial@nexansamercable.com Mining Applications: mining@nexansamercable.com

5 Conductor Size Grounding Nominal DC Resistance AC Resistance Inductive Voltage Drop AWG/ Number of Conductor Part No. Diameter Weight 90 C NEC 75 C NEC at 25 C at 90 C, 60Hz Reactance (Volts/Amp/ kcmil mm2 Conductors AWG/kcmil (inches) (lbs/1000 ft.) Ampacity Ampacity Ampacity (ohms/1000 ft.) (ohms/1000 ft.) 1000 ft.) CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG / CIRG / CIRG / CIRG / CIRG / CIRG / CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG CIRG Ampacities are based on Table (B) (16) of the National Electrical Code (NEC) for conductors rated 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B) (3) (a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section For Cable Color Codes and Stranding Information see page 12 Manufactured by Nexans AmerCable Fax:

6 CIR Standard CIR Control Cable UL Listed as Type TC-ER Multi-Conductor Gexol Insulated 0.6/1kV Rated 90 C Insulation GEXOL cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA V/IEC 1000V. For Cable Color Codes and Stranding Information see page 12 Safer to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors Gexol and CIR are registered trademarks of AmerCable Incorporated. Conductor Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. See Page 2 for Standard CIR Ratings & Approvals Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoplastic compound meeting UL 1309/CSA 245 and IEEE Application Designed and constructed to be a flexible alternative to Type MC cable where user desires the added crush and impact protection. Features n Passes the same stringent crush and impact testing required by UL 2225 for Type MC-HL n Gas & vapor tight impervious to water & air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC 4 Conductor Size Nominal DC Resistance AC Resistance Voltage Drop Number of Part No. Diameter Weight 90 C NEC 75 C NEC at 25 C at 90 C, 60Hz (Volts/Amp/ AWG mm2 Conductors (inches) (lbs/1000 ft.) Ampacity Ampacity (ohms/1000 ft.) (ohms/1000 ft.) 1000 ft.) CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR Ampacities are based on Table (B) (16) of the National Electrical Code (NEC) for conductors rated 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B) (3) (a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section

7 CIR Standard CIR Instrumentation Cable UL Listed as Type TC-ER Individually Shielded Pairs/Triads Gexol Insulated 0.6/1kV Rated 90 C Insulation GEXOL cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA V/IEC 1000V. Safer to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors See Page 2 for Standard CIR Ratings & Approvals For Cable Color Codes and Stranding Information see page 12 See Bend Radius on Page 1 Conductor Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Pairs/Triads Each pair/triad is twisted with a bare tinned drain wire. Each pair/triad is shielded with polyesterbacked aluminum foil tape to afford 100% coverage. Pair to pair, or triad to triad, isolation plus overall shielding is provided. Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoplastic compound meeting UL 1309/CSA 245 and IEEE Application Designed and constructed to be a flexible alternative to Type MC cable where user desires the added crush and impact protection. Features n Passes the same stringent crush and impact testing required by UL 2225 for Type MC-HL n Gas & vapor tight impervious to water & air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC Conductor Nominal DC Resistance Mutual Size Part No. Diameter Weight 20 C Capacitance Inductance AWG mm2 Pairs Triads (inches) (lbs/1000 ft.) (ohms/1000 ft.) (nf/1000 ft.) (mh/1000 ft.) CIR CIR CIR CIR CIR CIR CIR CIR CIR CIR VALUES: #16 Pairs / Triads Capacitance nf/1000 feet = 32 Inductance mh/1000 = 0.20 Resistance Ohms/1000 feet = 4.52 (@ 20 C) Gexol and CIR are registered trademarks of AmerCable Incorporated. Manufactured by Nexans AmerCable Fax:

8 CIRVFD CIR Type VFD Power Cable UL Listed as Type TC-ER & Type TC-ER-HL* Three Conductor Gexol Insulated 2kV Rated 90 C Power Conductors (x3) Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Insulation (2kV) Gexol cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA 245. Color: Gray with printed phase I.D. (Black- White-Red) Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoplastic compound meeting UL 1309/ CSA 245 and IEEE CIR VFD Ratings & Approvals Ground Conductors (x3) Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Gexol insulation sized per UL Color: Green Shield Overall tinned copper braid plus aluminum/polyester tape providing 100% coverage. Safer to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors n 90 C temperature rating n UL Listed as Marine Shipboard Cable (E111461) n UL Listed as Type TC-ER n UL Listed as TC-ER-HL* n American Bureau of Shipping (ABS) (99-BT5905-X) n Flame Retardant IEEE 1202 n Suitable for use in Class I, Div 2 and Zone 2 environments n Suitable for Class 1, Div 1 and Zone 1 environments *Cables up to 1 in OD Application A flexible, braid and foil shielded, 2kV power cable specifically engineered for use in variable frequency AC motor drive (VFD) applications. Features n Specially engineered cable design produces a longer cable life in VFD applications. n Overall braid and foil shield provides 100% coverage containing VFD EMI emissions. n Symmetrical insulated ground conductors reduce induced voltage imbalances and carry common mode noise back to the drive. n High strand count conductors and braid shield design is much more flexible, easier to install and more resistant to vibration than Type MC cable. n Gexol s lower dielectric constant (standard XLPEs, EPRs and other Type P insulation materials have higher dielectric constants) reduces reflected wave peak voltage magnitudes. This allows for longer output cable distances and minimizes the effect of high frequency noise induced into the plant ground system. n 2kV insulation thickness resists the repetitive 2x voltage spikes from 600V VFDs and reduces drive over current trip problems due to cable charging current. n Passes the same stringent crush and impact testing required by UL 2225 for Type MC-HL n Gas & vapor tight impervious to water and air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC 6 Industrial Applications: industrial@nexansamercable.com Mining Applications: mining@nexansamercable.com

9 Size Nominal Weight DC Resist. AC Resist. Inductive Voltage Drop Green Insulated IEEE NEC IEEE NEC AWG/ Part No. Diameter C, 60 Hz 90 C Grounding Ampacity Ampacity Ampacity Ampacity kcmil Inches* 1000 Ft. (Ohms/1k ft) (Ohms/1k ft) (Ohms/1k ft) (Volts/Amp/1k ft) Size (AWG) 90 C 90 C 75 C 75 C CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD /0-316CIRVFD /0-317CIRVFD /0-319CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD CIRVFD *Cable diameters are subject to a +/- 5% manufacturing tolerance Ampacities are based on Table (B) (16) of the National Electrical Code (NEC) for conductors rated 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B) (3) (a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section Gexol and CIR are registered trademarks of AmerCable Incorporated. Manufactured by Nexans AmerCable Fax:

10 CIRAG Arctic Grade CIR Power Cable Type TC-ER-HL* Three & Four Conductor + Ground Gexol Insulated 0.6/1kV Rated 90 C Insulation GEXOL cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA V/IEC 1000V. Safer to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors Conductor Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Brittlepoint as per ASTM D exceeds -65 C for Jacket and -75 C for Insulation Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoset compound meeting UL 1309/ CSA 245 and IEEE Application Designed and constructed to be a flexible alternative to Type MC cable where user desires crush and impact protection in arctic conditions. Features n Complies with the requirements for TC-ER-HL per UL 2225 n Exceeds CSA cold bend / cold impact (-40 C / -35 C) n Gas & vapor tight impervious to water and air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC See Bend Radius on Page 1 CIR Arctic Grade Ratings & Approvals n 90 C temperature rating n UL Listed as Marine Shipboard Cable (E111461) n UL Listed as Type TC-ER n UL Listed as TC-ER-HL* n American Bureau of Shipping (ABS) (99-BT5905-X) n Flame Retardant IEEE 1202 n Suitable for use in Class I, Div 2 and Zone 2 environments n Suitable for Class 1, Div 1 and Zone 1 environments* *Cables up to 1 in OD Gexol and CIR are registered trademarks of AmerCable Incorporated. 8 Industrial Applications: industrial@nexansamercable.com Mining Applications: mining@nexansamercable.com

11 Conductor Size Grounding Nominal DC Resistance AC Resistance Inductive Voltage Drop AWG/ Number of Conductor Part No. Diameter Weight 90 C NEC 75 C NEC at 25 C at 90 C, 60Hz Reactance (Volts/Amp/ kcmil mm2 Conductors AWG/kcmil * (inches) (lbs/1000 ft.) Ampacity Ampacity Ampacity (ohms/1000 ft.) (ohms/1000 ft.) 1000 ft.) CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG / CIRGAG / CIRGAG / CIRGAG / CIRGAG / CIRGAG / CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG CIRGAG Ampacities are based on Table of the National Electrical Code (NEC) for conductors rate 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B) (2) (a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section For Cable Color Codes and Stranding Information see page 12 Hawke Gland Types Hawke Gland Types Type CIR Industrial & Safe Area (IP68) 121 Increased Safety EExe 501/421 Explosion Proof 710 Class I, Div. 2 Class I, Zone 1 & 2 Flameproof 501/421 EExd Zone 1 & 2 Manufactured by Nexans AmerCable Fax:

12 CIRAG Arctic Grade CIR Control Cable Type TC-ER-HL* Multi-Conductor Gexol Insulated 0.6/1kV Rated 90 C Insulation GEXOL cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA V/IEC 1000V. For Cable Color Codes and Stranding Information, see page Safe to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors Gexol and CIR are registered trademarks of AmerCable Incorporated. Conductor Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Brittlepoint as per ASTM D exceeds -65 C for Jacket and -75 C for Insulation Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoset compound meeting UL 1309/CSA 245 and IEEE See page 8 for Arctic CIR Ratings & Approvals Application Designed and constructed to be a flexible alternative to Type MC cable where user desires crush and impact protection in arctic conditions. Features n Complies with the requirements for TC-ER-HL per UL 2225 n Exceeds CSA cold bend / cold impact (-40 C / -35 C) n Gas & vapor tight impervious to water & air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC Conductor Size Nominal DC Resistance AC Resistance Voltage Drop Number of Part No. Diameter Weight 90 C NEC 75 C NEC at 25 C at 90 C, 60Hz (Volts/Amp/ AWG mm2 Conductors * (inches) (lbs/1000 ft.) Ampacity Ampacity (ohms/1000 ft.) (ohms/1000 ft.) 1000 ft.) CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG Ampacities are based on Table of the National Electrical Code (NEC) for conductors rate 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B) (2) (a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section

13 CIRAG Arctic Grade CIR Instrumentation Cable Type TC-ER-HL* Individually Shielded Pairs/Triads Gexol Insulated 0.6/1kV Rated 90 C Insulation GEXOL cross-linked flame retardant polyolefin, meeting the requirements for Type P of IEEE 1580 and Type X110 of UL 1309/CSA V/IEC 1000V. Safer to Handle CIR has no sharp metal armor edges that imperil worker s hands during splicing and installation of connectors Brittlepoint as per ASTM D exceeds -65 C for Jacket and -75 C for Insulation Conductor Soft annealed flexible stranded tinned copper per IEEE 1580 Table 11. Pairs/Triads Each pair/triad is twisted with a bare tinned drain wire. Each pair/triad is shielded with polyester-backed aluminum foil tape to afford 100% coverage. Pair to pair, or triad to triad, isolation plus overall shielding is provided. Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoset compound meeting UL 1309/ CSA 245 and IEEE Application Designed and constructed to be a flexible alternative to Type MC cable where user desires crush and impact protection in arctic conditions. Features n Complies with the requirements for TC-ER-HL per UL 2225 n Exceeds CSA cold bend / cold impact (-40 C / -35 C) n Gas & vapor tight impervious to water & air n Smaller bend radius (up to 40% smaller) than Type MC n Reduced tray fill (up to 35% less) compared to Type MC n Considerably more flexible than Type MC n Reduced installation time and cost compared to Type MC n Glands for this product cost up to 50% LESS than those for Type MC For Cable Color Codes and Stranding Information see page 12 See page 8 for Arctic Grade CIR Ratings & Approvals Conductor Nominal DC Resistance Mutual Size Part No. Diameter Weight 20 C Capacitance Inductance AWG mm2 Pairs Triads * (inches) (lbs/1000 ft.) (ohms/1000 ft.) (nf/1000 ft.) (mh/1000 ft.) CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG CIRAG VALUES: #16 Pairs / Triads See Bend Radius on Page 1 Capacitance nf/1000 feet = 32 Inductance mh/1000 = 0.20 Resistance Ohms/1000 feet = 4.52 (@ 20 C) Manufactured by Nexans AmerCable Fax:

14 CIR Cable Color Codes Control Cables Colored Insulation Conductor # Base Color Tracer Color 1 Black 2 Red 3 Blue 4 Orange 5 Yellow 6 Brown 7 Red Black 8 Blue Black 9 Orange Black 10 Yellow Black 11 Brown Black 12 Black Red 13 Blue Red 14 Orange Red 15 Yellow Red 16 Brown Red 17 Black Blue 18 Red Blue 19 Orange Blue 20 Yellow Blue 21 Brown Blue 22 Black Orange 23 Red Orange 24 Blue Orange 25 Yellow Orange 26 Brown Orange 27 Black Yellow 28 Red Yellow 29 Blue Yellow 30 Orange Yellow 31 Brown Yellow 32 Black Brown 33 Red Brown 34 Blue Brown 35 Orange Brown 36 Yellow Brown 37 Black Power Cables 6 AWG and smaller = colored insulation 4 AWG and larger = print Conductor # Color 1 Black 2 Red 3 Blue 4 Orange Instrumentation Cables Pairs Triads Black, White Black, White, Red Pair / Triad number printed on conductors Individual Closest Equivalent Uninsulated Size Number Strand Dia. IEEE 45 Metric Size Conductor AWG/kcmil of Strands (inches) Std. Size (mm2) Dia. (inches) /0 2/0 4/ CIR Stranding Profile Industrial Applications: industrial@nexansamercable.com Mining Applications: mining@nexansamercable.com

15 Why Specify CIR Cables? The True Cable Cost Comparison Lower Total Installed Cost AmerCable CIR vs. Type CWCMC (MC-HL) Based on 100 ft. of cable, 2 glands and installation labor (cable & glands) 16 AWG 1 Shielded Pair... CIR Saves you 36% 14 AWG 3/C+G...CIR Saves you 37% 6 AWG 3/C+G...CIR Saves you 38% 4 AWG 3/C+G...CIR Saves you 33% 2/0 4/C+G... CIR Saves you 10% Glands for CIR Cables cost up to 50% LESS than those for Type MC Data Basis: 1. Labor rate $35.00/hr. 2. Labor time quotes based on long established Fluor Daniel Project Controls Standard Unit for Type TC and Type CWCMC cables for installation tray. 3. Identical installation for both products using a 100 ft. run basis. 4. Hawke A121 series glands used for CIR cables and Hawke N701 glands used for Type CWCMC cables. 5. MRO pricing is used for cables and glands. Manufactured by Nexans AmerCable Fax:

16 Nexans AmerCable is an ISO 9001 certified cable manufacturer that combines leading-edge manufacturing technology, innovative thinking, and high quality service to deliver the finest cable products available. Our professional design staff, field engineers and sales force work with you to create innovative, cost effective project solutions. Nexans AmerCable s manufacturing facility in El Dorado, Arkansas. What can you expect from Nexans AmerCable? Fastest Lead Times in the Industry On-Time Delivery Professional Sales, Support and Service Strategic Inventory Locations Tiger Brand Surface Mining Cables Type SH, Jumpers, Portable Power, Ship-to-shore, DLO. Foil shielded, power cables engineered for use in variable frequency AC drive applications. Tiger Brand Underground Mining Cables Factory Installed Cable Assemblies for Mining and Industrial Applications Single- and multi-conductor PV cables. AmerSol dual-certified (TÜV and UL). 350 Bailey Road El Dorado, AR Fax: , AmerCable Incorporated Industrial Applications: industrial@nexansamercable.com Mining Applications: mining@nexansamercable.com 10_14