SIP Endpoint Configuration
|
|
- Dayna Briggs
- 8 years ago
- Views:
Transcription
1 SIP Endpoint Configuration Configuration examples for SIP-endpoints connected to Version: Date: SEN VA SME SD 33 Siemens Enterprise Communications Siemens Enterprise Communications
2 Table of Content 1 SIP Endpoints in Scope SIP Features in Local SIP Features PCC for SIP endpoints Known restriction for all SIP endpoints Security considerations Configure a SIP Endpoint in SIP endpoint configuration examples OpenStage15/40 SIP Basic Configuration Call Forwarding Message Waiting Distinctive Ringing Known limitations and restrictions OptiPoint 410 standard S Basic Configuration Call Forwarding Message Waiting Distinctive Ringing Known limitations and restrictions OpenScape Personal Edition V Basic Configuration Hold/Retrieve/Alternate Transfer Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Gigaset S450IP / C470IP Basic Configuration Call Forwarding Message Waiting Distinctive Ringing Known limitations and restrictions X-lite SIP Basic Configuration Call Forwarding Message Waiting Distinctive Ringing Known limitations and restrictions SIP Endpoint Configuration Page 2
3 2.6 3CXPhone Basic Configuration Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Grandstream GXP Basic Configuration Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Grandstream GXV Basic Configuration Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Nokia E52/E75/N Basic Configuration Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Nokia C Basic Configuration SIP Endpoint Configuration Page 3
4 Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Mediatrix 4102S Basic Configuration Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Distinctive Ringing Local phone features Known limitations and restrictions Aastra 6739i Basic Configuration Hold/Retrieve/Alternate Transfer CLIP/CLIR/CNIP - Name and Number presentation Call Waiting / Call offer Call Forwarding Message Waiting Destinctive Ringing Local phone features Known limitations and restrictions SIP Endpoint Configuration Page 4
5 1 SIP Endpoints in 1.1 Scope This document describes the configuration of SIP-Endpoints used for integration of SIP features in V3. For each endpoint a list of necessary configuration steps is provided as well as hints which endpoint functions are not supported by the system. It is assumed that a device comes with default factory settings. Thus only the necessary configuration steps are described. Changes of default values are NOT recommended and thus NOT mentioned in this document. 1.2 SIP Features in The following features are supported in 1. Registration (Authentication) Before establishing or receiving calls an endpoint MUST register at the system. The system expects the configured call number for registration. For security reasons it is strongly recommended to use Authentication. 2. Basic call Incoming and outgoing as well as LateSDP Basic Call establishment is supported. 3. Name and Number presentation For each extension a name can be configured in the system. The number and name is presented during call establishment if no restriction is activated. Note: Most SIP endpoints offer the capability to configure a terminal name which is transported in the display part of the From: header field. The terminal name is not used in the system. The name configured in the system is used instead. 4. Call Waiting / Call Offer Call Waiting/Call offer is deactivated in default, but can be activated for SIP endpoints too. (subscriber configuration) 5. Call Forwarding (CFU/CFB/CFNR) Most SIP endpoints offer the capability to configure call forwarding targets. Note: It has to be checked that the call management rules of the system does not interfere with such an endpoint controlled forwarding. (e.g. if CFNR is configured in the system after 15 sec, endpoint controlled CF after 20 sec will not be performed) 6. Hold / Retrieve / Alternate Hold, Retrieve and alternate are supported for SIP endpoints. The system provides MOH (Music On Hold) for the held party. 7. Transfer (Attended/SemiAttended/Blind) 3 types of transfer are supported: - Attended Transfer: Before the call is transferred the transferor has an established consultation call. - SemiAttended Transfer: The Transferor goes in consultation and transfer as soon as the consulted party rings. - Blind Transfer: Transfer is invoked out of the original call without consultation call 8. Message Waiting Most SIP endpoints offer the capability to subscribe to a Voic server. An endpoint which has subscribed to the MWI service receives notifications about a message left in. 9. Distinctive ringing To allow distinctive ringing signals at SIP subscribers the alertinfo header field is included SIP Endpoint Configuration Page 5
6 in outgoing Invite s: e.g. Alert-Info: <Bellcore-dr1>;info=alert-internal By using this header field different ringing signals can be used for: "<Bellcore-dr1>;info=alert-internal" - normal (internal) alerting; "<Bellcore-dr2>;info=alert-external" - external alerting; "<Bellcore-dr3>;info=alert-recall" - recall alerting (e.g., following transfer) To make use if this feature the SIP endpoint has to be configured accordingly. 10. Video Video connections are supported between SIP endpoints connected to the same system and in a OpenScape network. Video connections are not supported on ITSP connections. 11. Codec support In an OpenScape environment the following codecs will be used: For gateway calls (analog/isdn) : G711a, G711ų and G729 For calls to the OpenStage HFA phones: G711a, G711ų, G729 and G722 For Fax gateway calls (analog/isdn): T.38 as well as G711-transparent (depending on the connected fax machine) For Fax calls to OSO application: T.38 Calls to other SIP devices device dependant 12. DTMF support In an OpenScape environment the recommended DTMF transport standard is RFC2833. No other method is supported (e.g. SIP Info) 1.3 Local SIP Features The following features may be supported locally in a SIP phone Caller list Consultation Call Conference DoNotDisturb (DND) Other SIP features are NOT supported in PCC for SIP endpoints Starting with OSO V3 3 rd party Call control (3PCC, RFC3725) is supported for the following features: Basic Call establishment Hold Retrieve Consultation Call Toggle/Alternate Transfer Call Deflect Call (Forward to new destination) Release Call! If 3PCC is used, the controlled SIP endpoint MUST support call waiting and call waiting MUST be allowed in the endpoint. Outgoing Invites for 3PCC calls contain the alert-info header field allowing for automatic call acceptance by the endpoint and entering handsfree mode: Alert-Info: <Bellcore-dr4>;info=alert-autoanswer SIP Endpoint Configuration Page 6
7 1.5 Known restriction for all SIP endpoints 1. Keypad procedures In general keypad procedures to invoke features (like *1 or #1 for call forwarding) are NOT supported for SIP Endpoints 2. Ring back tone During Transfer a held SIP endpoint does not get ring back tone, MOH is played instead 3. Forking SIP endpoints can be configured in groups (hunt group, ring group) and thus are able to participate in some group features offered by. Forking as it is defined in the SIP protocol is not supported. 4. Multiple registrations Multiple registrations for one number are not possible. 5. MOH As the system provides MOH during feature like Hold, the local MOH in the endpoint MUST be deactivated. If local MOH is enabled the phone user will hear a short burst of local MOH followed by the system MOH when a call is put on hold. In addition the phone user may hear a short burst of local MOH before a call is retrieved or released. 1.6 Security considerations With the increasing deployment of VoIP networks more and more attacks against VoIP equipment can be observed in such networks. SIP as an open and well-known protocol is implemented in various crack tools which are freely available in the internet. To avoid misuse of a SIP access careful configuration is crucial. For a SIP subscriber access the following rules should be followed: Activate authentication Use a non trivial password with o a minimum of 8 and a maximum of 20 characters o at least one upper case letter. (A - Z) o at least one lower case letter. (a - z) o at least one number. (0-9) o at least one special character o no more than 3 repeated characters Define a SIP user ID different from the Callno SIP Endpoint Configuration Page 7
8 1.7 Configure a SIP Endpoint in For the configuration of SIP endpoints start the Setup Wizard Telephones / Subscribers-> IP- Telephones : For SIP endpoints the Type MUST be set to SIP Client. Add or change the following data to your needs: Callno, Name and appropriate License Type! With the data entered in the overview table a SIP endpoint is able to register without authentication. For safety reasons it is strongly recommended to activate authentication for every SIP endpoint in the system. Press Edit to enter the Change Station page Check the box Authentication active and enter Password, SIP User ID and Realm. Chose a non trivial password according to the rules defined in 1.6 above The Realm MUST be present and is predefined with a default string. It may be changed if your deployment needs to have a specific string here. The SIP User ID MUST be present and is a string which is used during the authentication process. This should be e.g. the call number of the SIP endpoint with a prefix. The data configured here must also be entered in the SIP devices as described throughout this document. SIP Endpoint Configuration Page 8
9 SIP Endpoint Configuration Page 9
10 2 SIP endpoint configuration examples 2.1 OpenStage15/40 SIP Wiki-Page: Manuals: The following steps describe the necessary configuration for the OpenStage 15/40 SIP endpoints. The relevant configuration parameters are identical and the WBM pages are similar for both endpoints. Used Endpoint Software: OpenStage15 SIP V2 R SIP (Screenshots mostly taken with: V2 R SIP ) OpenStage40 SIP V2 R SIP Basic Configuration Default Administrator password: SIP Endpoint Configuration Page 10
11 Network IP- configuration: if no DHCP is used, enter the IP network configuration parameters as used in your network. Date and time: For a correct time and date display enter the IP- Address for SNTP-Server, if not provided by DHCP. SIP Endpoint Configuration Page 11
12 Registration & Basic Telephony System - System Identity enter the Endpoint number and name Phone Value configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Terminal number Terminal name Call number Optional, Phone name can only be seen in the network traces, uses the name configured in system System Registration:! For best interoperability the Server type MUST be set to Genesys. After changing this value the phone MUST be restarted. If the Option Genesys is NOT available other has to be used. In this mode. If Server type is set to OS Voice the endpoint will NOT go into service at OpenScape Office. SIP Endpoint Configuration Page 12
13 Phone Value SIP server address SIP registrar address SIP gateway address Realm User ID Password configured in : IP-Address of IP-Address of Left blank configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Realm SIP User ID / Username Password Auto-answer for 3PCC calls: To allow the endpoint to answer 3PCC calls automatically (and activate the speaker), the following features needs to be selected. Switch to the User Pages tab for that. SIP Endpoint Configuration Page 13
14 2.1.2 Call Forwarding The endpoint offers CFB Forward on busy CFNR Forward on no reply CFU Forward all calls The call forwarding targets must be entered first under Forwarding Favorites. SIP Endpoint Configuration Page 14
15 2.1.3 Message Waiting Subscribed MWI is supported by the Endpoint and a waiting message is signaled in the display or with a fixed Voic -Key. Switch to the Administrator Pages tab for that. Features- Services : to activate subscribing for MWI support enter the IP-Address Features- Configuration Voic number - enter the call number that will be used to establish a call to the Voic in case if a message is present SIP Endpoint Configuration Page 15
16 Local functions -> Message Settings The system always reports the amount of new messages (new items) to a SIP endpoint. There is no information about urgent messages (new urgent items) or old messages (old items, old urgent items). To avoid displaying useless information the Message settings should be configured hidden as shown in the following screenshot: Distinctive Ringing For distinctive ringing the OpenStage 15/40 Endpoints use the info= string received in the Alert-Info: header field. To configure different ringing signals the Ringer-Setting has to be filled with one of the following strings: 1. alert-internal" for Internal call 2. alert-external" for External call 3. "alert-recall" for Recall (e.g., following transfer) SIP Endpoint Configuration Page 16
17 2.1.5 Known limitations and restrictions System provided MOH Local MOH in the Phone MUST be deactivated. Switch to the User Pages tab for that.if local MOH is activated there will be a mixture of local and system provided MOH on the phone. Feature support OpenStage SIP provides some features which are NOT supported by (e.g. CallBack, Directed Pickup, ) To hide the CallBack feature from the UI deselect the following items Other features (e.g. directed pickup) cannot be disabled. SIP Endpoint Configuration Page 17
18 2.2 OptiPoint 410 standard S Wiki-Page: Manuals: The following steps describe the necessary configuration for the OptiPoint 410 Standard S Endpoint. Used Endpoint Software: OptiPoint 410 S V7 R Basic Configuration Default Administrator password: WBM Administrator menu: System SIP Environment Terminal details: Phone Value configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Phone number Phone name All other parameters left blank Call number Optional, Phone name can only be seen in the network traces, uses the name configured in system SIP Endpoint Configuration Page 18
19 SIP details: Phone Value Registrar IP address Server IP address Gateway IP address SIP realm SIP user ID New SIP password Miscellaneous: Phone Value Message Waiting IP address Voic number configured in : IP-Address of IP-Address of Left blank configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Realm SIP User ID / Username Password configured in : IP-Address of Access number of VM SIP Endpoint Configuration Page 19
20 WBM Administrator menu: System SIP Feature: These setting are left in default; the features are NOT supported by Auto-answer for 3PCC calls: To allow the endpoint to answer 3PCC calls automatically (and enter Handsfree mode), the feature Auto anser - CTI needs to be selected on the Feature access page.. (Screenshot see 2.2.2) SIP Endpoint Configuration Page 20
21 2.2.2 Call Forwarding The OptiPoint 410 S Endpoints support call forwarding. WBM Administrator menu: Feature Access: enable Call forwarding Feature in the dialog box as shown in next screenshot. Note: activate and select type of forwarding at the Endpoint SIP Endpoint Configuration Page 21
22 2.2.3 Message Waiting The OptiPoint 410 S Endpoints does NOT support the subscription to MWI service Distinctive Ringing For distinctive ringing the OptiPoint 410 Endpoints use the info= string received in the Alert-Info: header field. To configure different ringing signals the Ringer-Setting has to be filled with one of the following strings: 1. alert-internal" for Internal call 2. alert-external" for External call 3. "alert-recall" for Recall (e.g., following transfer) Known limitations and restrictions OptiPoint 410 SIP provides some features which are NOT supported by (e.g. Autoanswer, Autoreconnect, Group pickup, Hot line / warm line, Station controlled conference, CallBack, Call recorder, ) To hide most of these features from the UI deselect them in the Feature Access menu (see 2.2.3) and in the System SIP Feature menu (see 2.1.1) SIP Endpoint Configuration Page 22
23 2.3 OpenScape Personal Edition V4 UserGuide: Used Client Software: V3.2 R Basic Configuration After starting the OpenScape PE the following Logon window is opened: Choose a reasonable text for Login (e.g. your phone number) and Profile (e.g. your system/company name), enter your password and select Manage to configure your client. SIP Endpoint Configuration Page 23
24 Audio Schemas: First check, if the Audio Schema is configured and shows the correct connected devices. Without having a valid Audio schema OpenScape PE cannot be started. Advanced SIP Service Provider System services: Within this table services can be selected / deselected. Select Custom as server Type for and mark Video connections. All other checkboxes are unselected. SIP Endpoint Configuration Page 24
25 Advanced SIP Service Provider Mainline Enter the user (line) specific configuration data: : Phone Value configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit User Display Login Password Call number Optional, Phone name can only be seen in the network traces, uses the name configured in system SIP User ID / Username Password Advanced SIP Service Provider Registrar Enter the as Registrar Server Phone Value Server configured in : IP-Address of Advanced SIP Service Provider Proxy Enter the as Proxy Server SIP Endpoint Configuration Page 25
26 Phone Value Server configured in : IP-Address of Advanced SIP Service Provider Sounds Select the appropriate country specific Tone-Scheme Deselect MOH: Local MOH in the client MUST be deactivated. If local MOH is activated there will be a mixture of local and system provided MOH. SIP Endpoint Configuration Page 26
27 2.3.2 Hold/Retrieve/Alternate Hold, Retrieve and Alternate are supported by icons in the phone menu Transfer Attended and Blind Transfer is supported Call Waiting / Call offer Call waiting is controlled via the Functions menu, but it has to be enabled in OpenScape Office WBM as well. If call waiting is enabled, a second parameter is offered to control if a tone should be used for audible signaling Call Forwarding The client offers CFB Forward on busy CFNR Forward on no reply CFU Forward all calls SIP Endpoint Configuration Page 27
28 A dedicated call forwarding management function is available: Message Waiting To be completed Distinctive Ringing Not supported by OpenScape PE Local phone features OpenScape PE offers a local 3 party conference. Active and held call can be connected to a 3 way conference by activating conference in the phone menu. Conference is supported by the phone. Do Not Disturb can be activated by the Functions menu: Voice recording can be used to locally record a conversation. The recoded files are stored under \My Documents\My Music\VoiceRecordings Known limitations and restrictions SIP Endpoint Configuration Page 28
29 As OpenScape PE is provided for several communication servers there are some options/features offered, which are not supported in, e.g. Directed call pickup SIP Endpoint Configuration Page 29
30 2.4 Gigaset S450IP / C470IP For more information see the Gigaset homepage: The following steps describes the necessary configuration for the Gigaset S450IP/470IP Endpoints. The relevant configuration parameters are identical and the WBM pages are similar for both Endpoints. Used Endpoint Software: Gigaset S450IP V2 R SIP Gigaset C470IP V2 R SIP Basic Configuration Default Administrator password: 0000 IP Connections Parameter: if no DHCP is used, enter the IP network configuration parameters as used in your network. SIP Endpoint Configuration Page 30
31 Telephony->Connections (select provider) Gigaset offers the possibility to connect to several SIP providers. has to be configured as one provider. First Edit the data (see below) and then set the provider to Active Telephony->Connections (configure provider) Connection Name: Name shown in Gigaset WBM (no relationship to data) Personal Provider Data: enter the client related data here SIP Endpoint Configuration Page 31
32 Phone Value configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Authentication Name Authentication password Username Display name SIP User ID / Username Password Call number Optional, Phone name can only be seen in the network traces, uses the name configured in system Telephony->Connections Parameter / Show Advances Settings General Provider Data: enter the IP-address Network: active NO and NEVER SIP Endpoint Configuration Page 32
33 Telephony-> Number Assignment If more than one provider is configured on the device you MUST select the provider which should be used for outgoing calls. This step is not necessary if only one provider is used. Telephony-> Advances Settings -> DTMF over VoIP On S450IP set RFC2833 to allow sending of DTMF digits with RFC2833. On C470 IP set either automatic (default) or RFC Call Forwarding The endpoint offers CFB When busy CFNR No reply CFU Always SIP Endpoint Configuration Page 33
34 2.4.3 Message Waiting Activate the MWI support at Gigaset 450/470 IP Endpoint at the Administrator menu: Settings Telephony Network Mailbox Distinctive Ringing Not supported by Gigaset Known limitations and restrictions SIP Endpoint Configuration Page 34
35 2.5 X-lite SIP X-Lite 3.0: X-Lite 4.0: For information see the Counterpath homepage: Used Endpoint Software: X-Lite Version 3.0 build X-Lite Version 4.0 build Basic Configuration The following steps describes the configuration for the X-lite SIP Client Network & Registration V3.0: Select SIP Account Setting to enter the relevant account parameter V4.0: From the X-Lite menu, choose Softphone > Account Settings. The SIP Account window appears. In the Account tab, complete the User Details area. SIP Endpoint Configuration Page 35
36 To register the X-lite Client enter the parameters as shown below X-Lite V3: X-Lite V4: Phone Value configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Display Name Optional, Phone name can only be seen in the network traces, uses the name configured in system User Name (V3) User ID (V4) Password Authorization user name (V3) Authorization name (V4) Domain Call number Password SIP User ID / Username configured in : IP-Address of SIP Endpoint Configuration Page 36
37 2.5.2 Call Forwarding The V3.0 client offers CFB Forward to this address when busy CFNR Send calls to voic CFU Always forward to this address Individual call forwarding targets can be configured CFU and CFB, CFNR is supported to Voic only. Forwarding targets are configured with the call number. When the entries are saved they are displayed as the SIP-URI (e.g. CFU and CFB is NOT available in the (free) V4.0 client SIP Endpoint Configuration Page 37
38 2.5.3 Message Waiting To activate the MWI service with subscription enable the voic support and set the voic call number as shown in A waiting message is signaled with a special icon on the display of the X-lite client Distinctive Ringing Not supported by X-lite Client Known limitations and restrictions One Way payload The X-Lite Client has a "special" behaviour when negotiatin RTP capabilities. Offer from HiPath: (PCMA with highest priority) m=audio RTP/AVP Answer from XLite: (PCMA with highest priority too) m=audio RTP/AVP Usually a client will use the codec selected with highest priority (the first one sent back in SDP answer) for RTP too. X-Lite sent PCMA as prefered codec BUT uses PCMU in RTP. This will lead to one-way payload. The following actions can be taken to solve the issue: 1) In X-Lite 4 a configuration option is available to use the codec with highest priority 2) X-Lite V3: Delete PCMU codec in X-Lite Codec settings (this can be reached via Options Advanced settings) 3) If none of the above is feasable the problem may be eliminated by a configuration change in OSO codec settings: Change codec priority with PCMU to highest priority SIP Endpoint Configuration Page 38
39 2.6 3CXPhone For information see the 3CX homepage: 3CXPhone FREE SoftPhone for Windows, Android and Iphone 3CXPhone is a free softphone that you can use to make and receive VoIP phone calls from your PC, Iphone or Android based smartphone Used Software Version: Windows: 3CXPhone ver Basic Configuration Basic Settings Open the account settings dialogue and create a new (or edit the existing default) account SIP Endpoint Configuration Page 39
40 Phone Value Account name Extension Caller ID ID Password Local IP Displayed in the Phone, only local relevance. configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Call number Optional, Phone name can only be seen in the network traces, uses the name configured in system SIP User ID / Username Password configured in : IP-Address of SIP Endpoint Configuration Page 40
41 2.6.2 Hold/Retrieve/Alternate Hold, Retrieve and Alternate are supported either by the Hold button or by the line keys Transfer Attended - and Blind Transfer is supported. See: CLIP/CLIR/CNIP - Name and Number presentation The phone can display names (default) or the call number Call Waiting / Call offer Not supported by 3CX phone Call Forwarding Not supported by 3CX phone Message Waiting For this feature the Account advanced settings PBX voic has to be configured Distinctive Ringing Not supported by 3CX phone SIP Endpoint Configuration Page 41
42 2.6.9 Local phone features The phone allows to activate DND. For use with 3PCC Auto-Answer can be set. In this case the phone will answer incoming calls automatically. The phone provides a Call history list and a Missed Call List The phone provides the capability to record calls on the device Known limitations and restrictions Message Waiting: The 3CX phone does not correctly process the Message Summary notification sent by the system. Thus a waiting message is NOT signaled through the envelope- icon on the phone. Codec support: The free of charge version of the 3CX phone comes with codec support for PCMa,PCMU and GSM. If a call is initiated to a phone which is restricted to compressed codecs only this will lead to no payload or a call rejection. Speed dial keys If the speed dial keys are used, the phone subscribes to the presence service. This is not supported by, thus the keys show idle status. SIP Endpoint Configuration Page 42
43 2.7 Grandstream GXP280 For information see the Grandstream homepage: Used Endpoint: Produkt-Modell: GXP280 (HW0.3B) Software Version: Programm Bootloader Basic Configuration Default Administrator password: admin Basic Settings If no DHCP is used, enter the IP network configuration parameters as used in your network: SIP Endpoint Configuration Page 43
44 To get the correct time display set - Daylight Saving Time - Time Display Format - Date Display Format - Display Clock instead of Date according to your needs: Advanced settings: Enter the IP-Address of your as NTP server here: Advanced settings: The following settings should be left in default SIP Endpoint Configuration Page 44
45 If you have to update the phone SW, provide the address of your TFTP server here. In case you want to have automatic updates enabled e.g. during reboot, set the flags accordingly. The following entries can be left in default (North American tones). If local tones are required this has to be changed. Disable not supported features, this will hide this features on the UI SIP Endpoint Configuration Page 45
46 If you want to use a different language, you have to select secondary Language and provide the corresponding language file via TFTP. See downloadchapter Registration and Basic Telephony Account settings: Phone Value SIP-Server: SIP User ID: Authenticate Password: Authenticate ID : Name configured in : IP-Address of configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Call number Password Client-SIP User ID Optional, Phone name can only be seen in the network traces, uses the name configured in system Send DTMF: disable in-audio, enable via RTP (RFC2833) Adjust the codec settings if needed: SIP Endpoint Configuration Page 46
47 Special deployment Change Language: The GXP280 comes with two different languages (English,Chinese) If you want to have a different language it has to be downloaded via TFTP. A language pack (GXP_Language_Pack.zip) is available at the Grandstream download site. This language pack has the compiled file which is read to be used for GXP series. Each zip file has only one particular language in it. How to use: 1. Open the zip file 2. Open the desired language zip file 3. Copy the gxp.lpf to the TFTP server path and rename it with a postfix e.g. gxp_ger.lpf 4. Check that your TFTP Server is running. 5. Access the advance setting of the Web UI, select Secondary Language and enter postfix e.g. ger without the _ 6. Save and reboot the phone Hold/Retrieve/Alternate Pressing the Flash key will put a call on HOLD or retrieved it from HOLD. A consultation call can be established when a call is held. Toggle/alternate can be invoked by pressing the flash key during consultation.! HOLD and all features based on HOLD will be disabled when Send Flash Event is set to Yes Transfer Attended -, Semi-Attended- and Blind Transfer is supported. Semi Attended Transfer Mode MUST be set to Send REFER with early dialog. If set to RFC5589 (default) the transferor will remain busy until the transfer target accepts the call. Transfer can be disabled:. SIP Endpoint Configuration Page 47
48 2.7.4 CLIP/CLIR/CNIP - Name and Number presentation The phone can display names (default) or the call number Enable CLIR if required, by setting Send Anonymous Yes Anonymous Method Use Privacy Header Call Waiting / Call offer Call waiting is enabled by default in GXP280 but has to be enabled in WBM. As this is a station oriented parameter there is no need to configure it in the phone. Nevertheless two parameters are provided: Call Forwarding The endpoint offers CFU Always Call Forwarding unconditional CF has to be activated/deactivated on the phone via a predefined soft key Message Waiting For this feature the Account Settings Subscribe for MWI Voice Mail UserID: Access number of VM have to be configured. A waiting message is signaled by a red light on top of the phone Distinctive Ringing Not supported by GXP280 SIP Endpoint Configuration Page 48
49 2.7.9 Local phone features DND Do Not Disturb The MUTE key can be used to invoke DND. The feature can be deactivated by administration Conference GXP280 offers a local 3 party conference. Active and held call can be connected to a 3 way conference by pressing the CONF key. The feature can be deactivated by administration Known limitations and restrictions SIP Endpoint Configuration Page 49
50 2.8 Grandstream GXV3140 For information see the Grandstream homepage: Used Endpoint: Product highlights: 3 line multimedia phone with integrated video, multimedia player, Internet radio, IM client SIP Endpoint Configuration Page 50
51 2.8.1 Basic Configuration Default Administrator login admin, password: admin The phone supports up to 3 lines to make establish calls. To allow features like consultation or conference at least two accounts have to be configured in the phone with identical configuration parameters.! EXCEPTION: Only for account 1 the flag SIP registration=yes is activated. For endpoints connected to the LAN NAT Traversal MUST be set to NO SIP Endpoint Configuration Page 51
52 Configure the Account SIP settings, SIP registration and SUBSCRIBE for MWI MUST be set only for Account 1 (primary Account) SIP Endpoint Configuration Page 52
53 The dial plan has to be configured as {x+ *x+} to allow dialling of all strings (default dial plan). The Refer To Use Target Contact MUST be activated to allow transfer Hold/Retrieve/Alternate Hold / retrieve is controlled by a dedicated Key : Transfer Blind - and Attended-Transfer is supported SIP Endpoint Configuration Page 53
54 In Account->Call Settings-> Refer To Use Target Contact MUST be activated to allow Blind transfer Blind transfer is invoked by pressing and entering the transfer target. For invoking Attended-Transfer please refer to the description in the user manual. Excerpt from manual: Attended Transfer: Press the LINE button ( ) to select an idle line to use for attended transfer; this will place the other party on hold immediately. Dial the number that you wish to transfer to and after confirmation from the party, press the CALL TRANSFER button. The phone will display the following message: Dial Number (Blind) OR Select Line (Attended). (See figure below). Press the LINE button and select the line on hold CLIP/CLIR/CNIP - Name and Number presentation The phone can display names (default) or the call number Privacy can be activated by feature code and/or Web-interface Feature Code Feature *30 Block Caller ID (for all subsequent calls) *31 Send Caller ID (for all subsequent calls) Call Waiting / Call offer Call waiting is enabled by default in GXV3140 but has to be enabled in WBM too. As this is a station oriented parameter there is no need to configure it in the phone. Nevertheless two parameters are provided in Web Interface to disable call waiting: Control of Call Waiting is possible by feature codes as well. SIP Endpoint Configuration Page 54
55 2.8.6 Call Forwarding The endpoint offers CFU Unconditional Call Forward CFB Busy Call Forward CFNR Delayed Call Forward Call forwarding is activated/deactivated by feature codes. Feature Code Feature *72 Unconditional Call Forward: Dial *72 + Phone/Ext. Number followed by the # key. Wait for a dial-tone and then hang up (dial-tone means input is successful). *73 Cancel Unconditional Call Forward: Dial *73 and wait for a dial-tone before hanging up. *90 Busy Call Forward: Dial *90 + Phone/Ext. Number followed by the # key. Wait for a dial- tone and then hang up. *91 Cancel Busy Call Forward: dial *91 and wait for a dial-tone before hanging up. *92 Delayed Call Forward: Dial *92 + Phone/Ext. Number followed by the # key. Wait for a dial-tone and then hang up. *93 Cancel Delayed Call Forward: Dial *93 and wait for a dial-tone before hanging up. In addition a configuration via Web-Interface is possible. The timer for CFNR is configurable using the Web-interface only Message Waiting For this feature the Account Settings Voice Mail UserID: Access number of VM Subscribe for MWI have to be configured. A waiting message is signaled by the blue LED on top of the phone. Voic access is possible by dedicated key correctly if the Voice Mail UserID is configured Distinctive Ringing Not supported by GXV3140. The device can configure distinctive ringtones for 3 different caller IDs Local phone features GXV3140 offers a local 3 party conference. Active and held call can be connected to a 3 way conference by pressing the key Known limitations and restrictions Even if the phone comes with a lot of multimedia features and Web application support, the current software has some deficiencies in terms of call and feature handling. SIP Endpoint Configuration Page 55
56 As the phone supports up to 3 lines, features like consultation and conference are implemented by using different lines. It is not possible to invoke such features with only one line. Thus the user interface for handling such features is rather complex and needs a lot of key presses. The phone has no easy option to configure the local tones for a specific country. The phone needs a REBOOT for a lot of configuration changes. As it is not clear which change needs a reboot and which not it is recommended to REBOOT the phone after every configuration. SIP Endpoint Configuration Page 56
57 2.9 Nokia E52/E75/N97 E52: E75 N97: For information see the NOKIA homepage: Produkt-Modell: Nokia E52, E75, N97 Software Version: show firmware version on phone with *#0000# Nokia E75-(RM-412): S60, VoIP Rel 3.1, Firmware Nokia E52 (RM-469): S60, VoIP Rel 3.1, Firmware ( ) Nokia N97 (RM-505): S60, VoIP Rel 3.1, Firmware ( ) SIP VoIP Settings: E52/E75: SIP_VoIP_3_x_Settings_v2_0_en.sis N97: SIP_VoIP_3_1_Settings_S60_5_x_v1_0_en.sis SIP Endpoint Configuration Page 57
58 2.9.1 Basic Configuration Nokia E52/E75/N97 SIP client configuration: 1. Install SIP VoIP 3.x Settings application (SIP_VoIP_3_x_Settings_v2_0_en.sis) on your mobile device using Nokia PC Suite. 2. Menu-> Ctrl. Panel-> Net settings-> Advanced VoIP settings-> Create new service: 3. Select Create new SIP profile option: 4. Configure Username <SIP call IP address> 5. Configure Password <password> if authentication is configured in Open- Scape Office/HiPath: UserID = <SIP call number> and Realm = <OpenScape Office/HG1500 IP address> 6. Answer following question Would you like to create presence settings for the service? with No 7. Select following option for Activate service 8. Now the WLAN configuration is started, if not yet done: 9. Select your WLAN network (SSID is should be displayed) and enter Preshared key (PSK) Nokia phone does not allow editing of SIP profile settings as long as VoIP Service is active. If editing is necessary, then switch phone temporarily to Offline mode and do not allow WLAN access in Offline mode: Menu-> Ctrl. Panel-> Profiles-> Offline (or: push red on hook button and select Offline). The VoIP service is activated again after switching to profile General and next internet call attempt. It is recommended to disable Comfort Noise (CN) in SIP profile, to get better voice quality. Nokia phone shows this setting as CN codec, that is relevant for G.711 and ilbc codec if it exists in VoIP settings. 1. Switch phone to Offline mode 2. Menu-> Ctrl. Panel-> Net settings-> Advanced VoIP settings->voip services-> Select your Service-> Codecs: 3. Select the CN codec and delete it 4. switch phone back to profile General Hold/Retrieve/Alternate To be completed Transfer Attended Transfer is supported CLIP/CLIR/CNIP - Name and Number presentation The phone can display names (default) or the call number To be completed SIP Endpoint Configuration Page 58
59 2.9.5 Call Waiting / Call offer To be completed Call Forwarding Not supported Message Waiting Configuration for Voic Notification: Nokia devices can notify the user about new voice messages in HiPath Voic system ( or IVM but not EVM). There is always a new message in inbox, when number of new messages is changing. Voic must be configured, to get the notification and callback to voic option: 1. Switch phone to Offline mode 2. Menu-> Ctrl. Panel-> Net settings-> Advanced VoIP settings->voip services-> Select your Service-> Profile settings: 3. Select your SIP profile in Voic box Settings ID 4. Configure Voic box address <Voic call number>@</hg1500 IP address> 5. switch phone back to profile General Distinctive Ringing Not supported Local phone features To be completed Known limitations and restrictions Nokia phone configuration MUST be done via additional VoIP setting tool Comfort Noise feature should be disabled on Nokia E52 and E75 phone; otherwise the voice may appear shortly interrupted; disruptive clicking and noise will be heard on some ITSP calls (e.g. toplink) Voice in direction to Nokia Phone is distinctly delayed. Reducing Jitter buffer in Nokia phone (default = 200 ms) seems not to take effect. some call transfer scenarios may fail Nokia phones does not Re-Register, when LAN connectivity to SIP Registrar is lost for more than 2 minutes but WLAN connection is active. VoIP service is then disabled on phone. There is no problem, when WLAN connectivity is lost as in standard use case leaving WLAN home zone! Nokia devices cannot be used in an environment where the Signaling and Payload encryption feature is used Nokia devices have payload problems if Codec G723 is used, thus this codec has to be disabled is all devices (gateways, phones) in the network MR s related to Nokia devices SIP Endpoint Configuration Page 59
60 E52 E75 N97 H74052 call from HFA put on hold before release X X X H74070 call released when SIP is put on hold by HFA X X X H74074 TDM cannot be put on hold a second time X X X H74114 sporadically no transfer with Nokia SIP pos X X X No MR is not doing semi attended transfer (no REFER, - X - CANCEL after on hook) no MR call released when SIP is put on hold by TDM twice X - x no MR no SIP Re-Register when IP connection lost for X - x some minutes no MR E52 sometimes not responding after answering SIP X - - call H77595 No payload after blind transfer with SPE on X H way payload after blind transfer (G723) X H87997 No payload after hold/unhold with Nokia x H92992 mobility entry transit: no payl. after second x hold/retrieve SIP Endpoint Configuration Page 60
61 2.10 Nokia C7 For information see the NOKIA homepage: Produkt-Modell: C7-00 (Type RM-675) Software Version: show firmware version on phone with *#0000# Release PR1.1 Software version/date Custom version/date To enable and configure the SIP client on the device you must download the SIP VoIP settings application and install it on the phone BEFORE you start. SIP VoIP Settings: SIP_VoIP_3_1_Settings_Symbian_3_v1_0_en.sis Basic Configuration Download and install SIP VoIP 3.x Settings application on your mobile device using Nokia PC Suite.! SIP telephony in the Nokia device needs careful configuration. If you started with the configuration and the device does not register successfully: please delete ALL services and profiles related to SIP telephony before you continue. Open the Menu, select Settings, select Connectivity and scroll down to Admin. Settings: -> -> SIP Endpoint Configuration Page 61
62 On the next screen select Net settings (NOT SIP settings!), select Advanced VoIP settings and last (but not least) Create new service: -> -> Select Create new SIP profile option: Configure Username with the string containing <call IP address> Configure Password as configured in OpenScape Answer would you like to create presence settings for the service with No At the end the device start to register, but as the configuration is not yet complete, press exit and continue with the configuration of the SIP settings:. -> Select the configured service and scroll down to the Proxy and Registrar server entry: -> -> -> In Proxy server the Proxy server address must be entered. In Registrar server you must enter Realm and Username as configured in OpenScapeOffice. Please note that Username is not the callnumber! SIP Endpoint Configuration Page 62
63 Account settings: Phone Value Proxy server Registrar server Password: Registrar Server -> Username: Registrar Server -> Realm: configured in : IP-Address of configured in (see 1.7): Telephones / Subscribers-> IP Telephones -> Edit Password SIP User ID / Username Realm!! The Username is used at two different locations in the device configuration menu and has to be filled with two different strings! 1. call number when entering Username during creation of the service 2. Client-SIP User ID when configuring the registrar server Nokia C7 does not allow editing of SIP profile settings as long as VoIP Service is active. If editing is necessary, then switch phone temporarily to Offline mode and do not allow WLAN access in Offline mode. Power off the phone and d o not connect to WLAN after power on. Now configuration should be possible To establish a Basic Call the destination number has to be entered in the dialler and via Options-> Call the SIP server has to be selected: -> If DTMF post dialing is required press Options, select Send DTMF and Enter manually -> -> -> SIP Endpoint Configuration Page 63
64 Hold/Retrieve/Alternate Hold and retrieve are offered during call. Hold Retríeve active and held call Swap/Alternate call Transfer Attended and automated transfer is supported CLIP/CLIR/CNIP - Name and Number presentation The phone can display names (default) and/or the call number r Privacy/Call number suppression can be activated by the Call settings menu available via the Options softkey in the dialer. Select Call settings and set Sent my internet call id to No. SIP Endpoint Configuration Page 64
65 Call Waiting / Call offer Call waiting is deactivated by default and must be activated in the phone. The Call settings menu is available via the Options softkey in the dialer. Select Call settings and activate Internet call waiting Call Forwarding Not supported Message Waiting -> -> Configuration for Voic Notification: Nokia devices can notify the user about new voice messages in HiPath Voic system ( or IVM but not EVM). There is always a new message in inbox, when number of new messages is changing. Goto Advanced VoIP settings -> VoIP services and open your SIP profile. Under Profile settings the Voic server must be entered: Select your SIP profile in Voic box settings ID Configure Voic box address <Voic call number>@< IP address> Distinctive Ringing Not supported. SIP Endpoint Configuration Page 65
66 Local phone features Conference is not supported by the phone. Do Not Disturb can be activated by the Call settings menu available via the Options softkey in the dialer. Select Call settings and set Internet call alert to Off Known limitations and restrictions Please refer to the general statements in SIP Endpoint Configuration Page 66
67 2.11 Mediatrix 4102S For information see the Mediatrix homepage: Used Endpoint: Produkt-Modell: Mediatrix 4102S Software Version: Dgw (Profile: 4102-MX-D ) Basic Configuration Default factory values for the web access are: User Name: admin Password: administrator Network Settings If no DHCP is used, enter the IP network configuration parameters as used in your network: Enter Default Gateway, DNS and SNTP under Host settings Enter device IP-Address under Interfaces SIP Endpoint Configuration Page 67
SIP Endpoint configuration hints. 1.1 Nokia E52/E75/N97... 1 1.2 Nokia C7... 5
1 Nokia phones 1.1 Nokia E52/E75/N97... 1 1.2 Nokia C7... 5 1.1 Nokia E52/E75/N97 E52: E75 N97: For information see the NOKIA homepage: http://www.nokia.de/produkte/mobiltelefone Produkt-Modell: Nokia
More informationOpenScape Business V1. Tutorial SIP Endpoint Configuration - OpenScape Desk Phone IP / OpenStage SIP Version 1.2
OpenScape Business V1 Tutorial SIP Endpoint Configuration - OpenScape Desk Phone IP / OpenStage SIP Version 1.2 About Unify Unify is one of the world s leading communications software and services firms,
More informationSIP-T22P User s Guide
SIP-T22P User s Guide Thank you for choosing this T-22 Enterprise IP Phone. This phone is especially designed for active users in the office environment. It features fashionable and sleek design, and abundant
More informationP160S SIP Phone Quick User Guide
P160S SIP Phone Quick User Guide Version 2.2 TABLE OF CONTENTS 1.0 INTRODUCTION... 1 2.0 PACKAGE CONTENT... 1 3.0 LIST OF FIGURES... 2 4.0 SUMMARY OF KEY FUNCTIONS... 3 5.0 CONNECTING THE IP PHONE... 4
More informationIpiphony Phone System. User Manual. 1 P a g e
Ipiphony Phone System User Manual 1 P a g e About this Guide This guide explains how to use the basic features of your new Aastra phones. Not all features listed are available by default. Contact your
More informationNote: these functions are available if service provider supports them.
Key Feature New Feature Remote Maintenance: phone can be diagnosed and configured by remote. Zero Config: automated provisioning and software upgrading even through firewall/nat. Centralized Management:
More informationDPH-140S SIP Phone Quick User Guide
DPH-140S SIP Phone Quick User Guide Version 1.0 TABLE OF CONTENTS 1.0 INTRODUCTION... 1 2.0 PACKAGE CONTENT... 1 3.0 LIST OF FIGURES... 2 4.0 SUMMARY OF KEY FUNCTIONS... 3 5.0 CONNECTING THE IP PHONE...
More informationConfiguration Notes 290
Configuring Mediatrix 41xx FXS Gateway with the Asterisk IP PBX System June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 About Mediatrix 41xx Series FXS Gateways...
More informationTechnical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure Inn-Phone SIP Phone for use with MCD SIP CoE NOTICE The information contained in this document is believed to be accurate in all respects but is not
More informationNetComm V90 VoIP Phone Quick Start Guide Draft Release 0.1
NetComm V90 VoIP Phone Quick Start Guide Draft Release 0.1 Copyright NetComm Ltd Overview NetComm V90 SIP VoIP Phone User Guide Table of Contents Overview... 3 V90 VoIP Phone Specification...4 Shipping
More informationFLX UC1000/1500 Registering with Siemens HiPath 4000 & OpenScape Voice Server
Technical Note FLX UC1000/1500 Registering with Siemens HiPath 4000 & OpenScape Voice Date: February 1, 2016 This technical note gives a detailed description on how to register a Revolabs FLX UC1000/1500
More information#!) * & /! $* - 01 $& -$ 2 1 $& -# 32# $- - + $- -*!45 $-
! Version Date Status Owner 1.0 2009-11-09 Released 1.1 2010-01-05 Hints for Fax added Provider hints and new layout 1.2 2010-12-17 Additional hints and corrections 1.3 2011-05-19 Updates for new STUN
More informationBusiness VoIP Solution Training 04/2009
Business VoIP Solution Training 04/2009 IP Phone Deployment Scenario 1 Company LAN All the IP Phones and PBX are within the same local area network, no firewall and NAT traversal issues IP PBX 2 IP Phone
More informationZed One Hosted VoIP Telephony User Guide. A document to provide end user guidance on enterprise-class Hosted VoIP Telephony solution.
Zed One Hosted VoIP Telephony User Guide A document to provide end user guidance on enterprise-class Hosted VoIP Telephony solution. Contents Unity Desktop Client Quick Start User Guide... 3 Broadworks
More informationHow To Program A Talkswitch Phone On A Cell Phone On An Ip Phone On Your Ip Phone (For A Sim Sim) On A Pc Or Ip Phone For A Sim Phone On Iphone Or Ipro (For An Ipro) On
TALKSWITCH DOCUMENTATION ADDING IP PHONES TO TALKSWITCH RELEASE 6.50 CT.TS005.008104 ANSWERS WITH INTELLIGENCE COPYRIGHT INFORMATION Copyright 2011 Fortinet, Inc. All rights reserved. Fortinet, FortiGate,
More informationYour Phones Display and Buttons. Using Your Phone. Personalising Your Phone. Call Handling Features
Your Phones Display and Buttons Using Your Phone Using Line Keys Using Busy Lamp Fields Handling Missed Calls Do Not Disturb Making Calls Taking Calls Taking Multiple Calls Accessing Voicemail Personalising
More informationVoIP Handset User Manual. Digital Voice Quality Business Grade Handset Easy Plug & Play
Digital Voice Quality Business Grade Handset Easy Plug & Play Table of Contents 1.0 Getting Started... 1 1.1 Unpacking the box... 1 1.2 Assembling the Phone... 2 2.0 Phone Button Features... 3 3.0 Phone
More informationUsing Basic Call Management Functions
Using Basic Call Management Functions This chapter provides instructions on using your basic phone functions. It includes the following sections: Managing the Audio Source and Volume, page 28 Answering
More informationIP Office SIP Extension Support
SIP Extension Support - Issue 1b - (05 August 2009) 2009 AVAYA All Rights Reserved. Notice While reasonable efforts were made to ensure that the information in this document was complete and accurate at
More information1 VoIP/PBX Axxess Server
- 1 1 VoIP/PBX Axxess Server The Axxess Server supports comprehensive Voice Over Internet Protocol network services, which are based on the Open Source Asterisk VoIP software. The Axxess Server VoIP telephony
More informationUser Guide. Aastra 6753i
User Guide Aastra 6753i Content Phone overview Basic telephony features How to place a call How to answer a call How to terminate a call How to redial a number How to mute a call How to set a call on hold
More information1 P a g e. Digital Voice Services Business User Guide
1 P a g e Digital Voice Services Business User Guide Feature Access Codes *62 Voice Portal *86 Direct Voice Mail Retrieval *77 Anonymous Call Rejection Activation *87 Anonymous Call Rejection Deactivation
More informationHow To Configure A Linksys Pap2T With Virtualbpx On A Cell Phone On A Pc Or Ipad Or Ipa (For Ipa) On A Ipa Or Ip2T On A Sim Sim (For Sim Sims
Linksys PAP2T Configuration with VirtualPBX The Linksys PAP2T is an inexpensive ATA device that connects to the internet and registers with your Virtual PBX extension, allowing you to use any analog phone
More informationVoIP Telephone Adapter User s Manual
VoIP Telephone Adapter User s Manual Last Update: 2008/10/10 1 Introduction...3 1.1 Product Overview (Single Phone Port Model)...3 1.2 Product Overview (Dual Phone Port Model)...4 2 IVR Interface for TA...6
More informationUsing Advanced Phone Features
Using Advanced Phone Features This chapter describes how to configure advanced features on your IP Phone. It contains the following sections: Configuring Privacy and Security, page 9 Enabling and Using
More informationWireless VoIP Phone User s Manual
Wireless VoIP Phone User s Manual Table of Contents Chapter 1 Overview of the WiFi phone... 5 1.1 Front Panel and Keypad...5 1.2 Removing and Installing the Battery...7 1.3 Charging the WIFI PHONE...8
More informationPhone & Features Guide
Phone & Features Guide Seventh Edition 11/19/08 Contents Introduction To The Guide...6 1. Star2Star Supported Phones...7 2. Polycom Phones...9 a). Answering a Call...9 b). Making a Call...9 c). Microphone
More informationApplication Notes for Avaya IP Office 7.0 Integration with Skype Connect R2.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Avaya IP Office 7.0 Integration with Skype Connect R2.0 Issue 1.0 Abstract These Application Notes describe the steps to configure an Avaya
More informationAPTECH IP-PBX QUICK USER S GUIDE. Accounts and Lines
APTECH IP-PBX QUICK USER S GUIDE Accounts and Lines From a Phone In Off-hook state, select an idle line and dial tone will be heard, or without picking a specific Line start dialing any number and at the
More informationIP101 VoIP Phone. User Manual
IP101 VoIP Phone User Manual 1 Introduction...3 1.1 Hardware Overview...3 1.2 Software Overview...4 2 Setup the IP Phone system by using keypad...4 2.1 Keypad Description...4 2.2 Keypad Function and Setting
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationVersion Date Status Owner. 1.0 2009-02-04 Released for HiPath OpenOffice ME V1 F. Kneissl / K.-W. Weigt
History of Change Version Date Status Owner 1.0 2009-02-04 Released for HiPath OpenOffice ME V1 F. Kneissl / K.-W. Weigt 1.1 2010-09-01 Update for OpenScape Office MX V2 and hints for Fax F. Kneissl 1.2
More informationBusiness Telephone User Guide
Business Telephone User Guide 1 Proud to provide Conway s Electric, Water, Cable, Internet and Telephone services. Welcome to Conway Corporation Business Telephone Service We take pride in providing superior
More informationApplication Notes for Revolabs FLX UC 1000 with Avaya IP Office - Issue 0.1
Avaya Solution & Interoperability Test Lab Application Notes for Revolabs FLX UC 1000 with Avaya IP Office - Issue 0.1 Abstract These Application Notes describe the configuration steps required to integrate
More informationIntermedia Cloud Softphone. User Guide
Intermedia Cloud Softphone User Guide FOR MORE INFO VISIT: CALL US EMAIL US intermedia.net +1.800.379.7729 sales@intermedia.net 1 Contents 1 Introduction... 3 1.1 Cloud Softphone Features... 3 2 Installation...
More informationAbstract. Avaya Solution & Interoperability Test Lab
Avaya Solution & Interoperability Test Lab Application Notes for Configuring the Ascom Wireless IP- DECT SIP Solution with Avaya IP Office in a Converged Voice over IP and Data Network - Issue 1.1 Abstract
More informationHosted VoIP Phone System. Admin Portal User Guide for. Call Center Administration
Hosted VoIP Phone System Admin Portal User Guide for Call Center Administration Contents Table of Figures... 4 1 About this Guide... 6 2 Accessing the Hosted VoIP Phone System Administration Portal...
More informationProvisioning and configuring the SIP Spider
Provisioning and configuring the SIP Spider Administrator Guide Table of Contents 1. Introduction... 3 2. Manual Provisioning... 4 3. Automatic Provisioning... 5 3.1 Concept... 5 3.2 Preparing the configuration
More informationAastra 673xi / 675xi. Telephony with SIP Phones at the Aastra 800/OpenCom 100 Communications System User Guide
Aastra 673xi / 675xi Telephony with SIP Phones at the Aastra 800/OpenCom 100 Communications System User Guide Welcome to Aastra Thank you for choosing this Aastra product. Our product meets the strictest
More informationIP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
More informationVersion: SIPPBXUM.101
SIPPBX 6200A User s Manual Version: SIPPBXUM.101 CH1. Overview... - 5-1.1 Specifications... - 5-1.2 Hardware Overview... - 8-1.2.1 The Front Panel... - 8-1.2.2 The Back Panel... - 8 - CH2. Start to configure
More informationOfficeSuite Simplicity Phone and System Features. General Settings. Phone status (Icon is i ) Time and date (The Settings icon is a wrench)
OfficeSuite Simplicity Phone and System Features General Settings Phone status (Icon is i ) Press OK and use the navigation keys to select the Status menu. Select item SIP Account Status to view the associated
More informationWireless VoIP Phone. Table of Contents. User s Manual
Wireless VoIP Phone User s Manual Table of Contents Chapter 1 Overview the WiFi Phone... 6 1.1 Front Panel and Keypad... 6 1.2 Removing and Installing the Battery... 8 1.4 Powering the WiFi Phone On and
More informationEZLoop IP-PBX Enterprise SIP Server
EZLoop IP-PBX Enterprise SIP Server Copyright 2007 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 sales@teletronics.com www.teletronics.com CH1. Overview...4 1.1 Specifications...4
More information3CX Application Partner Program Inter-Working Report
3CX Application Partner Program Inter-Working Report Partner:ESCENE IP Phones Application Type: Escene SIP Phones Application Name:Models US102N,ES220N,ES290N\292N,ES320N,ES330N,ES410,ES620 3CX Platform:
More informationQB-241/ QB-242 VoIP Phone. User Manual V 1.10
QB-241/ QB-242 VoIP Phone User Manual V 1.10 Preface About this product The use of this equipment may be subject to local rules and regulations. The following rules and regulations may be relevant in
More informationKE1020A INSTALL GUIDE
KE1020A INSTALL GUIDE Table of Contents 1 Check for Required Items...2 2 Installation Steps...2 2.1 Installation View... 2 2.2 Connection Chart to Determine Cable Types... 2 3 Ready to Use...3 3.1 Changing
More informationAvaya IP Office 8.1 Configuration Guide
Avaya IP Office 8.1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Revision: 1.1 Date: 10/14/2013 Copyright 2013 by tekvizion PVS, Inc. All Rights Reserved.
More informationMediatrix Gateway 440x Series Quick Configuration Guide
Mediatrix Gateway 440x Series Quick Configuration Guide All BRI Mediatrix gateways are pre-configured on ETH1 port with DHCP and ETH2 port with static IP 192.168.0.10. All PRI Mediatrix gateways are pre-configured
More informationRiOffice Users Manual
RiOffice Users Manual Rio Networks 9/23/2009 Contents Available Services... 4 Core PBX Features... 4 Voicemail Features... 4 Call Center Features... 4 Call Features... 4 Using Your Phone... 5 Phone Layout...
More informationAvaya Solution & Interoperability Test Lab
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Ascom Wireless IP-DECT SIP Solution with Avaya IP Office 9.0 in a Converged Voice over IP and Data Network - Issue 1.0 Abstract
More informationmobile uc client End user guide
mobile uc client End user guide 1 Mobile Unified Communications User Guide About Mobile UC Currently, the following five Droid Phones are supported for Mobile UC: + Droid X + Droid X2 + Droid 2 Global
More informationVoipSwitch softphones
VoipSwitch softphones sales@voipswitch.com 3/21/2011 Voiceserve ltd.grosvenor House,1 High Street,London United Kingdom 1 Contents Introduction and solution overview... 2 iphone mobile softphone... 3 Google
More informationTables of Contents. Getting Started... - 1 -
11/2010 Versie 1 About This Guide Thank you for choosing the tiptel IP 28xs which is especially designed for power users in the office environment. It features fashionable and sleek design, abundant telephony
More informationMOBILITY FOR iphone USER GUIDE
MOBILITY FOR iphone USER GUIDE VERSION 20.0.2 401 Market Street, First Floor Philadelphia, PA 19106 877.258.3722 www.alteva.com Table of Contentsl 1. About Alteva Mobility for iphone... 3 2. Installation...
More informationAlgo 8180 Integration with Zultys
January 13 Algo 8180 Integration with Zultys Author: Zultys Technical Support Department This document describes the integration of Algo 8180 SIP Audio Alerter with the Zultys MX. Algo 8180 can be integrated
More informationSIP Trunking using Optimum Business Sip Trunk Adaptor and the Zultys MX250 IP PBX
SIP Trunking using Optimum Business Sip Trunk Adaptor and the Zultys MX250 IP PBX Table of Contents Goal 3 Prerequisites 3 Zultys MX250 Configuration 4 Network Settings 4 Phone Registration and Assignment
More informationAastra 480i Broadsoft SIP VoIP Telephone User s Guide
Aastra 480i Broadsoft SIP VoIP Telephone User s Guide Initial Start-Up/Restart The first time you plug in your phone and every time you restart your phone it automatically goes through the start-up process.
More informationHosted Phone System User Guide
Hosted Phone System User Guide GXP-2020 Phone System GXP-2010 Phone System Agency Number: 1234 585 Lifetime Street Sunny, FL 10024 904-646-5837 Last Updated 6/25/2009 User friendly guide to using your
More informationVerizon Collaboration Plug-In for Microsoft Outlook User Guide
Verizon Collaboration Plug-In for Microsoft Outlook User Guide Version 4.11 Last Updated: July 2011 2011 Verizon. All Rights Reserved. The Verizon and Verizon Business names and logos and all other names,
More informationmanagedip Hosted TDS Table of Contents Calling Features User Guide
Table of Contents Anonymous Call Rejection... 2 Automatic Callback... 2 Call Forwarding... 3 Call Park/Directed Call Park... 7 Call Park Retrieve... 8 Call Pickup... 8 Call Retrieve... 8 Call Return...
More informationWiFi Phone WP589 User Guide
WiFi Phone WP589 User Guide 001.001.024 2010/06/22 1 n CONTENTS For your safety...5 Getting Started...6 Phone Overview...6 To insert the battery...6 Charging the battery...7 Turn on and turn off the phone...7
More informationDigital Voice Services Residential User Guide
Digital Voice Services Residential User Guide 2 P a g e * Feature Access Codes *11 Broadworks Anywhere (pulling call to alternate phone) *62 Access Voicemail *72 Call Forwarding Always Activation *73 Call
More informationTechnical Configuration Notes
MITEL SIP CoE Technical Configuration Notes Configure MCD for use with OpenIP SIP Trunking service SIP CoE 11-4940-00186 NOTICE The information contained in this document is believed to be accurate in
More informationHosted VoIP Phone System. Desktop Toolbar User Guide
Hosted VoIP Phone System Desktop Toolbar User Guide Contents 1 Introduction... 3 1.1 System Requirements... 3 2 Installing the Telesystem Hosted VoIP Toolbar... 4 3 Accessing the Hosted VoIP Toolbar...
More informationNew and updated functions
Gigaset S675 IP, S685 IP, C470 IP, C475 IP: New and updated functions This document is a supplement to the user guide for the following Gigaset VoIP phones: Gigaset C470 IP, Gigaset C475 IP, Gigaset S675
More informationKerio Operator. User Guide. Kerio Technologies
Kerio Operator User Guide Kerio Technologies 2015 Kerio Technologies s.r.o. Contents Logging into Kerio Operator.................................................... 6 Which Kerio Operator interfaces are
More informationNokia Call Connect v1.1 for Cisco User s Guide. Part Number: N450000431 Rev 003 Issue 1
Nokia Call Connect v1.1 for Cisco User s Guide Part Number: N450000431 Rev 003 Issue 1 Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without
More informationAlcatel-Lucent OmniPCX Office R8.1 Maintenance Software
Alcatel-Lucent OmniPCX Office R8.1 Maintenance Software Software version: System 810/051.001 OMC 810/26.1a This document lists the correction delta between the maintenance software and the Technical Released
More informationQuick set-up instructions for. The Avois AV-3500 IP Phone
Solwise Ltd. Quick set-up instructions for The Avois AV-3500 IP Phone www.solwiseforum.co.uk The Solwise Forum is designed to be the first port-of-call for technical support and sales advice for the whole
More informationVerizon Collaboration Plug-In for Microsoft Outlook User Guide
Verizon Collaboration Plug-In for Microsoft Outlook User Guide Version 4.11 Last Updated: July 2011 2011 Verizon. All Rights Reserved. The Verizon and Verizon Business names and logos and all other names,
More informationCisco SPA901 1-Line IP Phone Cisco Small Business IP Phone
Cisco SPA901 1-Line IP Phone Cisco Small Business IP Phone Durable, Affordable, Feature-Rich IP Telephone for the Home Office and Business Small, affordable, single line business class IP Phone Connect
More informationTechnical Bulletin 43565 Using Polycom SoundPoint IP and Polycom SoundStation IP Phones with Asterisk
Technical Bulletin 43565 Using Polycom SoundPoint IP and Polycom SoundStation IP Phones with Asterisk Introduction This document provides introductory information on how to use Polycom SoundPoint IP phones
More informationHow To Set Up A Gxp280 Ip Phone On A Cell Phone On Your Computer Or Ip Phone (Siphone) On A Sim Sim Sim Or Ipro (Cell Phone) On Your Ipro Or Ipo (Cellphone) On
GXP280 Small Business IP Phone Quick Installation Guide Part Number: 9620001302A Document Version Number: 1.0 1 GXP280 IP Phone Quick Installation Guide WARNING: Please DO NOT power cycle the GXP280 when
More informationPhone & Features Guide. Edition Eleven
Phone & Features Guide Edition Eleven Contents Introduction To The Guide... 11 1. Star2Star Supported Phones... 12 2. Polycom Phones... 15 a). Answering a Call... 15 b). Making a Call... 15 c). Microphone
More informationApplication Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationUsing Spectralink IP-DECT Server 400 and 6500 with Cisco Unified Communication Manager, 3 rd party SIP
Using Spectralink IP-DECT Server 400 and 6500 with Cisco Unified Communication Manager, 3 rd party SIP Technical Bulletin Page 1 Introduction This document provides introductory information on how to use
More informationMediatrix 4404 Step by Step Configuration Guide June 22, 2011
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents First Steps... 3 Identifying your MAC Address... 3 Identifying your Dynamic IP Address...
More informationCisco SPA302D Mobility Enhanced Cordless Handset
USER GUIDE Cisco SPA30D Mobility Enhanced Cordless Handset Contents Chapter 1: Getting Started 1 Overview 1 Understanding Your Cisco SPA30D Cisco SPA30D Display Screen 4 Turning the Handset On and Off
More information480i BROADSOFT SIP IP PHONE RELEASE # 1.0 ADMINISTRATOR GUIDE
480i BROADSOFT SIP IP PHONE RELEASE # 1.0 ADMINISTRATOR GUIDE Aastra Telecom will not accept liability for any damages and/or long distance charges, which result from unauthorized and/or unlawful use.
More informationIP Office 7.0 and BCM 6.0 SIP Interoperability Configuration Notes
IP Office 7.0 and BCM 6.0 SIP Interoperability Configuration Notes Abstract: This document provides information on how to configure a network solution with IP Office 7.0 and BCM 6.0 using SIP trunks. 2011
More informationGSM VOIP GATEWAY LEVEL. User Guide. GB 400 010 with GSM module Two-way converter between VoIP and GSM
GSM VOIP GATEWAY GB 400 010 with GSM module Two-way converter between VoIP and GSM User Guide LEVEL 2 Dear customers, Congratulations on purchasing our product - GSM Gateway GB 400 010. You have acquired
More informationExtension Manual. User portal, Dial codes & Voice mail for 3CX Phone System Version 7.0
Extension Manual User portal, Dial codes & Voice mail for 3CX Phone System Version 7.0 Copyright 2006-2008, 3CX ltd. http:// E-mail: info@3cx.com Information in this document is subject to change without
More informationExtension Manual User portal, Dial codes & Voice mail for 3CX Phone System Version 6.0
Extension Manual User portal, Dial codes & Voice mail for 3CX Phone System Version 6.0 Copyright 2006-2008, 3CX ltd. http://www.3cx.com E-mail: info@3cx.com Information in this document is subject to change
More informationWave SIP Trunk Configuration Guide FOR BROADVOX
Wave SIP Trunk Configuration Guide FOR BROADVOX Last updated 1/7/2014 Contents Overview... 1 Special Notes... 1 Before you begin... 1 Required SIP trunk provisioning and configuration information... 1
More informationumobility User Guide Windows Mobile Smart Phone
umobility User Guide Windows Mobile Smart Phone Table of Contents 1 Getting Started... 4! Installing umobility on Your Windows Mobile Smartphone Device...5! Running umobility...6! Minimizing umobility...7!
More informationSIP Trunking Quick Reference Document
SIP Trunking Quick Reference Document Publication Information SAMSUNG TELECOMMUNICATIONS AMERICA reserves the right without prior notice to revise information in this publication for any reason. SAMSUNG
More informationGW400 VoIP Gateway. User s Guide
GW400 VoIP Gateway User s Guide P/N: 956YD30001 Copyright 2006. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. i Table of Contents
More informationBroadSoft Partner Configuration Guide
BroadSoft Partner Configuration Guide Grandstream GXW-400X FXS Analog Gateway & HandyTone HT-50X Analog Telephone Adapter April 2007 Document Version 1.1 BroadWorks Guide Copyright Notice Copyright 2007
More informationApplication Notes for Configuring Avaya IP Office 9.0 with HIPCOM SIP Trunk Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Avaya IP Office 9.0 with HIPCOM SIP Trunk Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationFortiVoice. Version 7.00 User Guide
FortiVoice Version 7.00 User Guide FortiVoice Version 7.00 User Guide Revision 2 28 October 2011 Copyright 2011 Fortinet, Inc. All rights reserved. Contents and terms are subject to change by Fortinet
More informationBroadband Telephony. Terminal Equipment Requirements and Specifications
Broadband Telephony Terminal Equipment Requirements and Specifications TABLE OF CONTENTS 1 Introduction... 3 1.1 Scope... 3 1.2 Intended audience... 3 1.3 Notice... 3 1.4 Definitions... 3 2 BBT Service
More informationTable of Contents GETTING STARTED... 3. Enter Password Dialog...3 Using Online Help...3 System Configuration Menu...4
Table of Contents DV2000 Configuration - Service Release 3.0 GETTING STARTED... 3 Enter Password Dialog...3 Using Online Help...3 System Configuration Menu...4 SYSTEM CONFIGURATION OVERVIEW... 5 Using
More informationHigh Link Co.,Ltd VOIP PHONE. GF302 User Guide. SIP and IAX2. Version 1.1
High Link Co.,Ltd VOIP PHONE SIP and IAX2 GF302 User Guide Version 1.1 Content 1.Introducing 1.1 Hardware Overview 1.2 LED and Interface Description 1.3 Keypads Description 2. Installing Guide 3.Configuration
More informationAbout. IP Centrex App for ios Tablet. User Guide
About IP Centrex App for ios Tablet User Guide December, 2015 1 2015 by Cox Communications. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic,
More informationMyIC setup and configuration (with sample configuration for Alcatel Lucent test environment)
MyIC setup and configuration (with sample configuration for Alcatel Lucent test environment) N.B. Goto MyIC Preferences in the System Toolbar. Description: this may be any appropriate description of the
More information9236245 Issue 2EN. Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation
9236245 Issue 2EN Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation Nokia 9300 Configuring connection settings Legal Notice Copyright Nokia 2005. All rights reserved. Reproduction,
More informationTOSHIBA. 1. While on a call, press the Cnf/Trn button. 2. Dial another station or outside number. 3. After the called party answers, press the
Telephone User Instructions Your phone is programmed with a Direct Dial Number, which is. Your 4-digit extension is. You may also have a rollover line. If your first line is busy, calls to your main number
More information