18 AWG thru 8 AWG Not greater than 100/30 100/30. 6 AWG thru 1/0 AWG Not greater than 200/60 100/30
|
|
- Calvin Young
- 8 years ago
- Views:
Transcription
1 Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS s Used to support cables in vertical raceways or risers. Relieves the strain that would be placed on terminations, the interior of panels, or other devices to which the cables are connected. Properly designed cable supports must not only be capable of supporting a given weight of cable with a good margin of safety but must also support the cable without damaging the insulation or excessively reducing the amount of insulation over the conductor in the area where the cable is supported. Requirements for Cable Supports in the National Electrical Code reads as follows: Supporting Conductors in Vertical Raceways. (A) Spacing Intervals - Maximum. Conductors in vertical raceways shall be supported if the vertical rise exceeds the values in Table (A). One cable support shall be provided at the top of the vertical raceway or as close to the top as practical. Intermediate supports shall be provided as necessary to limit supported conductor lengths to not greater than those specified in Table (A). Spacing for Conductor Supports Size of Wire Support of Conductors in Vertical Raceways Example: A 10-story building contains a vertical conduit run from the basement to the top floor, approx. 110 feet/34 meters in length. The raceway contains 4/0 copper conductors. Per Table (A), the unsupported cable length cannot exceed 80 feet/25 meters. Therefore, one cable support is required at or near the top of the vertical riser, and one intermediate support is required at or near the midpoint in the conduit run, assuring that any unsupported cable length does not exceed 80 feet/25 meters. Aluminum or Copper - Clad Aluminum Feet/Meters Copper Feet/Meters 18 AWG thru 8 AWG Not greater than 100/30 100/30 6 AWG thru 1/0 AWG Not greater than 200/60 100/30 2/0 AWG thru 4/0 AWG Not greater than 180/55 80/25 over 4/0 AWG kcmil Not greater than 135/41 60/18 over 350 kcmil kcmil Not greater than 120/36 50/15 over 500 kcmil kcmil Not greater than 95/28 40/12 over 750 kcmil Not greater than 85/26 35/11 TWO or more wires - Indoors - at voltages to 600 Volt ONE or more wires - Indoors - at all voltages Retrofit - TWO or more wires - Indoors - at voltages to 600 Volt Retrofit - ONE or more wires - Indoors - at all voltages Ventilating - ONE or more wires - Outdoors - at all voltages Ventilating - Bakelite - ONE or more wires - Outdoors - at all voltages Non-ventilating - ONE or more wires - Outdoors - at all voltages Locking - Horizontal/Vertical - ONE or more wires - Indoors - at all voltages Space Maker - ONE or more wires - Indoors - at all voltages Pull Box - ONE or more wires - Outdoors at all voltages Wire Armored Cable - In conduit or supported by structure Recommended O-Z/Gedney Cable Supports Type S Type R Type D Type DR Type CMT Type V Type C Type K Type M Type W Type F/FS/FT 1602
2 s Two basic types of cable supports are offered for use with non-armored cable. They both utilize the pozi-grip Wedging Plug. pozi-grip is a unique manufacturing technique for lining the cable grooves with a coarse grain grit using a high strength epoxy adhesive. This grit improves the cable support holding power and does not injure the jacket or insulation on the cable. One Piece Plug Type S This type consists of a metal body having an insulating liner with a knurled and tapered inside surface and a one piece impregnated hardwood wedging plug having a groove for each wire. This type support is recommended for use with all types of non-armored cables 600 Volts or less, as it is the easiest to install, impossible to install incorrectly and it provides ventilation of the conduit. This design is used in our Types S and D Cable Supports. The basic principles of their assembly are illustrated below. Type S 1 Screw body on the end of the conduit or connector in place of the regular insulating bushing. 2 Pull wires and arrange temporary means of support. Multiple Segment Plug Type R This type consists of an all metal body having a tapered inner surface and a canvas bakelite multiple segment wedging plug so constructed that each cable is supported between grooves in adjacent segments. This construction provides the uniform pressure distribution required by the softer types of insulations frequently used at higher voltages. This design is used in non-ventilating types R, DR, W, C, K and M, and Ventilating Compound Types CMT, and V. The basic principles of their assembly are illustrated below. Type R 1 Screw body on the end of the conduit or connector in place of the regular insulating bushing. 2 Pull wires and arrange temporary means of support. COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS 3a. Remove all pulling compound from wires in the area where they pass through the cable support. 3b. Place the plug between the wires as close to the top of the body as possible. Care should be taken to locate each wire in the proper groove. 3a. Remove all pulling compound from wires in the area where they pass through the cable support. 3b. Place the segments of the plug around the wires. Where more than two segments are involved the top of each plug segment has numbers at each end and it is important that these are paired with the corresponding numbers on the adjacent plug segments. Commercial Products 4 Tap the plug firmly into the support body. 4 Tap the plug segments evenly and firmly into the support body. 1603
3 S: For Two or More Wires - Indoors - at Voltages to 600 Vac For Rigid Conduit, IMC and EMT with pozi-grip S-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS For supporting non-armored electrical cables in vertical conduit risers. Threaded for Rigid Conduit and IMC. Use with all types of insulations at voltages to and including 600 Volt. The fastest and easiest type cable support to install. The knurled insulating inner surface and one piece impregnated hardwood pozi-grip plug provide positive support well in excess of code requirements. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. If mounting on a non-metallic/non-grounded conduit, a Lay-In- Lug grounding lug should be mounted on cable support body. For Threadless Rigid Conduit, Threadless IMC, or EMT, the body can be attached to the male threads of a set-screw or compression connector. For PVC Conduit, use a PVC terminal adapter. Bodies: malleable or ductile iron with hot dip galvanized finish Bodies: available in cast aluminum. Add suffix -A to catalog number. Example: S-1500A-1. UL Standard: 514B UL Listed: E11853 CSA Standard: C22.2 No.18.3 CSA Certified: Options For Lay-In-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. Illustrated Impregnated Hardwood pozi-grip Wedging Plug Shape and special gripping surface of grooves in plug give maximum support to cable. Malleable or Ductile Iron Body Tapered inside surface of insulating bushing is knurled to grip cable. 1604
4 S: For Two or More Wires - Indoors - at Voltages to 600 Vac For Rigid Conduit, IMC & EMT with pozi-grip S-style Wedging Plug. Complete Fitting 2-4 Same Any Number of Different or 5 or More Same Catalog Number Body Only 1-1/2 S S S-1500-BO 2 S S S-2000-BO 2-1/2 S S S-2500-BO 3 S S S-3000-BO 3-1/2 S S S-3500-BO 4 S S S-4000-BO Plug Only * 5 S S S-5000-BO 6 S S S-6000-BO 2-4 Same Any Number of Different or 5 or More Same Dimensions in Inches/Millimeters 1-1/2 SPLG SPLG / / SPLG SPLG / / /2 SPLG SPLG / / SPLG SPLG / / /2 SPLG SPLG / / SPLG SPLG / /3.88 COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS 5 SPLG SPLG / / SPLG SPLG / /139.7 Commercial Products * Cable support plugs will not be supplied undrilled. 1605
5 D: For Two or More Wires Already Installed in Conduit - Indoors - at Voltages to 600 Vac Retrofit Type Split Bakelite Body with pozi-grip S-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS For supporting non-armored electrical cables in vertical conduit risers. Retrofit type cable support can be installed after conductors are pulled and terminated. Split body rests on existing bushing atop any conduit raceway. The two halves of the body are placed around the cables, seated on the existing bushing and securely held together by the steel band set in a groove around the body. The plug is then wedged between the cables. Use with all types of insulations at voltages to and including 600 Volts. The tapered, knurled insulating inner body surface and pozigrip plug provide support well in excess of code requirements. Bodies: two molded canvas bakelite halves. Inside surface is knurled to grip cables Band: steel/zinc plated Bolts and nuts: stainless steel UL Standard: 514B UL Listed: E11853 CSA Standard: C22.2 No.18.3 CSA Certified: Illustrated Impregnated Hardwood pozi-grip Wedging Plug Shape and special gripping surface of grooves in plug give maximum support to cable. Two molded Canvas Bakelite halves. Inside surface is knurled to grip cables. Steel band, Zinc Plated. Bolts and nuts are Stainless Steel. Existing Bushing Existing Conduit 1606
6 D: For Two or More Wires Already Installed in Conduit - Indoors - at Voltages to 600 Vac Retrofit Type Split Bakelite Body with pozi-grip S-style Wedging Plug. Complete Fitting 2-4 Same Any Number of Different or 5 or More Same Approx. Turning Radius R Inside Number of Straps 1-1/2 D D / / / / / D D / / / / / /2 D D / / / / / D D / / / / / /2 D D / / / / / D D / / / / /50.8 Plug Only * 5 D D / / / / / D D / / / / / Same Any Number of Different or 5 or More Same Approx. Turning Radius R Inside Number of Straps 1-1/2 SPLG SPLG / / / / / SPLG SPLG / / / / / /2 SPLG SPLG / / / / / SPLG SPLG / / / / / /2 SPLG SPLG / / / / / SPLG SPLG / / / / / SPLG SPLG / / / / /50.8 COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS 6 SPLG SPLG / / / / /50.8 Commercial Products * Cable support plugs will not be supplied undrilled. 1607
7 R: For One or More Wires - Indoors - at all Voltages For Rigid Conduit, IMC and EMT with pozi-grip R-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS s For supporting non-armored electrical cables in vertical conduit risers. Due to the possibility of Magnetic Induction Heating, a single alternating current conductor should not be used in iron fittings. Threaded for rigid conduit and IMC. Use with all types of insulations at all voltages. The pozi-grip wedging plug exerts uniform pressure around the cable, providing holding force in excess of that required by code without deforming cable insulation. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. If mounting on a non-metallic/non-grounded conduit, a Lay- In-Lug grounding lug should be mounted on cable support body. For Threadless Rigid Conduit, Threadless IMC, or EMT, the body can be attached to the male threads of a set-screw or compression connector. Body: malleable or ductile iron with hot dip galvanized finish Optional Bodies: available in cast aluminum. Add suffix -A to catalog number. Example: R-1501A-1. UL Standard: 514B UL Listed: E11853 CSA Standard: C22.2 No.18.3 CSA Certified: Options For Lay-In-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. Illustrated Canvas Bakelite pozi-grip Wedging Plug For one wire type, the plug consists of two pieces. For two wires or more, there is one piece for each wire. Shape and special gripping surface of grooves in plug give maximum support to each cable and distributes even pressure around its entire circumference. Malleable or Ductile Iron Body Inside tapered surface is machined to assure proper seating of the Wedging Plug. 1608
8 R: For One or More Wires - Indoors - at all Voltages For Rigid Conduit, IMC and EMT with pozi-grip R-style Wedging Plug. Complete Fitting Any Number of Different or 5 or More Same Catalog Number Body Only 1-1/2 R R R-1501-BO 2 R R R-2001-BO 2-1/2 R R R-2501-BO 3 R R R-3001-BO 3-1/2 R R R-3501-BO 4 R R R-4001-BO Plug Only * 5 R R R-5001-BO 6 R R R-6001-BO Any Number of Different or 5 or More Same Dimensions in Inches/Millimeters 1-1/2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / /95.3 COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS 5 RPLG RPLG / / RPLG RPLG / /133.4 Commercial Products * Cable support plugs will not be supplied undrilled. 1609
9 DR: For One or More Wires Already Installed in Conduit - Indoors - at all Voltages Retrofit Type Split Bakelite Body with pozi-grip R-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS For supporting non-armored electrical cables in vertical conduit risers. Due to the possibility of Magnetic Induction Heating, a single alternating current conductor should not be used in iron fittings. Retrofit type cable support can be installed after conductors are pulled and terminated. Split body rests on existing bushing atop any conduit raceway. Use with all types of insulations at all voltages. The pozi-grip wedging plug exerts uniform pressure around the cable, providing holding force in excess of that required by code without deforming cable insulation. Bodies: two molded canvas bakelite halves Wedging plug: canvas bakelite pozi-grip Band: steel/zinc plated Bolts and nuts: stainless steel UL Standard: 514B UL Listed: E11853 CSA Standard: C22.2 No.18.3 CSA Certified: Illustrated Canvas Bakelite pozi-grip Wedging Plug For one wire type, the plug consists of two pieces. For two wires or more, there is one piece for each wire. Shape and special gripping surface of grooves in plug give maximum support to each cable and distributes even pressure around its entire circumference. Two molded Canvas Bakelite halves. Inside surface is knurled to grip cables. Steel band, Zinc Plated. Bolts and nuts are Stainless Steel. Existing Bushing Existing Conduit 1610
10 DR: For One or More Wires Already Installed in Conduit - Indoors - at all Voltages Retrofit Type Split Bakelite Body with pozi-grip R-style Wedging Plug. Complete Fitting Any Number of Different or 5 or More Same Approx. Turning Radius R Inside Number of Straps 1-1/2 DR DR / / / / / DR DR / / / / / /2 DR DR / / / / / DR DR / / / / / /2 DR DR / / / / / DR DR / / / / /50.8 Plug Only * 5 DR DR / / / / / DR DR / / / / /50.8 Any Number of Different or 5 or More Same Approx. Turning Radius R Inside Number of Straps 1-1/2 RPLG RPLG / / / / / RPLG RPLG / / / / / /2 RPLG RPLG / / / / / RPLG RPLG / / / / / /2 RPLG RPLG / / / / / RPLG RPLG / / / / / RPLG RPLG / / / / /50.8 COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS 6 RPLG RPLG / / / / /50.8 Commercial Products * Cable support plugs will not be supplied undrilled. 1611
11 CMT: Ventilating, Compound, Threaded Type. For One or More Wires - Outdoors - at all Voltages For Rigid Conduit, IMC and EMT with pozi-grip R-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS To support non-armored electrical cables in vertical conduit risers, furnish a weatherproof seal and provide ventilation at the top of the conduit. Due to the possibility of Magnetic Induction Heating, a single alternating current conductor should not be used in iron fittings. Threaded for rigid conduit and IMC. Use with all types of insulations at all voltages. This device not only supports the cable, but furnishes a weatherproof seal and provides ventilation at the top of the conduit riser. The temperature in a conduit riser can be reduced 15 F/-9.4 C to 20 F/ -6.6 C with proper venting. To obtain full effect of this decrease, the lower end of the conduit must be open or vented by use of the conduit ventilators. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. If mounting on a non-metallic/non-grounded conduit, a Lay- In-Lug grounding lug should be mounted on cable support body. For threadless rigid conduit, threadless IMC, or EMT, the body can be attached to the male threads of a set-screw or compression connector. For PVC conduit, use a PVC terminal adapter. Body: malleable or ductile iron with hot dip galvanized finish Complete Fitting Optional Material Bodies: available in cast aluminum. Add suffix -A to catalog number. Example: CMT A-1. For Lay-In-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. For insulating compound, see O-Z/Gedney dozseal Insulating Compound page. UL Standard: 514B Dimensions in Inches/Millimeters Compound Any Number of Different or 5 or More Same Required Pints Plug Only * 2 RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / * Cable support plugs will not be supplied undrilled. Illustrated Any Number of Different or 5 or More Same Compound Chamber Cable Support Body Ventilating Ports Existing Conduit Catalog Number Body Only 2 CMT CMT CMT-2000-BO 2-1/2 CMT CMT CMT-2500-BO 3 CMT CMT CMT-3000-BO 3-1/2 CMT CMT CMT-3500-BO 4 CMT CMT CMT-4000-BO 5 CMT CMT CMT-5000-BO 6 CMT CMT CMT-6000-BO 1612
12 V: Ventilating, Compound, Setscrew type. For One or more wires - Outdoors - at all voltages All Bakelite Cable Support For Threadless Rigid Conduit and IMC with pozi-grip R-style Wedging Plug. To support non-armored electrical cables in vertical conduit risers, furnish a weatherproof seal and provide ventilation at the top of the conduit. Use with all types of insulations at all voltages. A special cable support made of canvas bakelite. This support furnishes a weatherproof seal and provides ventilation at the top of the conduit riser. The temperature in a riser can be reduced 15 F/-9.4 C to 20 F/-6.6 C with proper venting. To obtain full effect of this decrease, the lower end of the conduit must be open or vented by use of the conduit ventilators. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. Body can also be mounted on EMT in trade sizes thru 4. Body and plug: canvas bakelite Options Can also be supplied for standard tapered ends of fiber conduit. Contact your local sales representative. For insulating compound, see O-Z/Gedney dozseal Insulating Compound page. Complete Fitting Illustrated Cable Support Plug Setscrew UL Standard: 514B UL Listed: E Any Number of Different or 5 or More Same Compound Chamber Cable Support Body Ventilating Ports Existing Conduit Catalog Number Body Only 2 V V V-2005-BO 2-1/2 V V V-2505-BO 3 V V V-3005-BO 3-1/2 V V V-3505-BO 4 V V V-4005-BO 5 V V V-5005-BO 6 V V V-6005-BO COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS Commercial Products Plug Only * Any Number of Different or 5 or More Same Dimensions in Inches/Millimeters Compound Required Pints 2 RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / * Cable support plugs will not be supplied undrilled. 1613
13 C Compound: Non-Ventilating. For One or More Wires Outdoors - at all Voltages For Rigid Conduit, IMC and EMT with pozi-grip R-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS To seal the end of conduit and support non-armored electrical cables in vertical conduit risers. Due to the possibility of Magnetic Induction Heating, a single alternating current conductor should not be used in iron fittings. Threaded for rigid conduit and IMC. Use with all types of insulations at all voltages. This device not only supports the cable, but furnishes a watertight seal at the top of a conduit riser. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. If mounting on a non-metallic/non-grounded conduit, a Lay- In-Lug grounding lug should be mounted on cable support body. For threadless rigid conduit, Threadless IMC, or EMT, the body can be attached to the male threads of a set-screw or compression connector. For PVC conduit, use a PVC terminal adapter. Body: malleable or ductile iron with hot dip galvanized finish Optional Material Bodies: available in cast aluminum. Add suffix -A to catalog number. Example: C-2004A-1. Complete Fitting Illustrated Options Can also be supplied for standard tapered ends of fiber conduit. Contact your local sales representative. For Lay-in-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. For insulating compound, see O-Z/Gedney dozseal Insulating Compound page. UL Standard: 514B UL Listed: E11853 Any Number of Different or 5 or More Same Compound Chamber Cable Support Body Existing Conduit Catalog Number Body Only 2 C C C-2004-BO 2-1/2 C C C-2504-BO 3 C C C-3004-BO 3-1/2 C C C-3504-BO 4 C C C-4004-BO 5 C C C-5004-BO 6 C C C-6004-BO Plug Only * Any Number of Different or 5 or More Same Dimensions in Inches/Millimeters Compound Required Pints 2 RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / * Cable support plugs will not be supplied undrilled. 1614
14 K Locking Style: Horizontal or Inverted - One or More Wires - Indoors - at all Voltages For Rigid Conduit, IMC and EMT with pozi-grip R-style Wedging Plug. Can be installed in horizontal or inverted position. For supporting non-armored electrical cables in conduit. Due to the possibility of Magnetic Induction Heating, a single alternating current conductor should not be used in iron fittings. Threaded for Rigid Conduit and IMC. Use with all types of insulations at all voltages. The design of this support is similar to the Type R except that is it is equipped with a locking collar which securely holds the pozi-grip wedging plug in place. This permits the support to be installed in any position and provides holding force against pull in either direction. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. If mounting on a non-metallic/non-grounded conduit, a Lay- In-Lug grounding lug should be mounted on cable support body. For Threadless Rigid Conduit, Threadless IMC, or EMT, the body can be attached to the male threads of a set-screw or compression connector. For PVC Conduit, use a PVC terminal adapter. Body and locking collar: malleable or ductile iron with hot dip galvanized finish Optional Material Cable support body and locking collar: cast aluminum. Add suffix -A to catalog number. Example: K-1503A-1. Options Can also be supplied for standard tapered ends of fiber conduit. Contact your local sales representative. For Lay-in-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. UL Standard: 514B UL Listed: E11853 Any Number of Different or 5 or More Same Catalog Number Body Only Complete Fitting 1-1/2 K K K-1503-BO 2 K K K-2003-BO 2-1/2 K K K-2503-BO 3 K K K-3003-BO 3-1/2 K K K-3503-BO 4 K K K-4003-BO 5 K K K-5003-BO 6 K K K-6003-BO Illustrated Any Number of Different or 5 or More Same Locking Collar Bakelite Bushing Cable Support Body Existing Conduit Dimensions in Inches/Millimeters Plug Only * 1-1/2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / /2 RPLG RPLG / / RPLG RPLG / / RPLG RPLG / / RPLG RPLG / /146.1 COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS Commercial Products Includes Locking Collar and Bushing. * Cable support plugs will not be supplied undrilled. 1615
15 M: Space-Maker Style - One or More Wires - Indoors - at all Voltages For Rigid Conduit, IMC and EMT with pozi-grip R-style Wedging Plug. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS Use where there is insufficient room for a cable support inside a junction box. For supporting non-armored electrical cables in vertical conduit risers. Due to the possibility of Magnetic Induction Heating, a single alternating current conductor should not be used in iron fittings. Use with all types of insulations at all voltages. This fitting is similar to the Type R support, except that it is threaded at the top to allow fastening to a cabinet (1 4 max. thickness) with standard locknuts or threading into tapped (NPT) openings. Body Only can be ordered separately, for installation prior to wire pulling. Plug Only can be ordered later, once wires are in place. If mounting on a non-metallic/non-grounded conduit, a Lay- In-Lug grounding lug should be mounted on cable support body. For Threadless Rigid Conduit, Threadless IMC, or EMT, the body can be attached to the male threads of a set-screw or compression connector. For PVC Conduit, use a PVC terminal adapter. Body: malleable or ductile iron with hot dip galvanized finish Optional Material Cable support body: available in cast aluminum. Add suffix -A to catalog number. Example: M-1520A-1. Complete Fitting Knockout Size Options Can also be supplied for standard tapered ends of fiber conduit. Contact your local sales representative. For Lay-In-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. UL Standard: 514B UL Listed: Any Number of Different or 5 or More Same Catalog Number Body Only 1-1/2 2 M M M-1520-BO 2 2-1/2 M M M-2025-BO 2-1/2 3 M M M-2530-B O 3 3-1/2 M M M-3035-BO 3-1/2 4 M M M-3540-BO 4 5 M M M-4050-BO 5 6 M M M-5060-BO Plug Only * Knockout Size Illustrated Locknut Any Number of Different or 5 or More Same Locknut Existing Conduit Dimensions in Inches/Millimeters Max. Body Top Thread Length Approx. eight 1-1/2 2 RPLG RPLG / / / /2 RPLG RPLG / / / /2 3 RPLG RPLG / / / /2 RPLG RPLG / / / /2 4 RPLG RPLG / / / RPLG RPLG / / / RPLG RPLG / / /104.9 Includes two locknuts. * Cable support plugs will not be supplied undrilled. 1616
16 W: Pull Box Style - Raintite Enclosed - For One or More Wires - at all Voltages For Threaded Rigid Conduit & IMC with pozi-grip R-style Wedging Plug. s For all types of insulations at all voltages. Provides intermediate support of non-armored conductors in an indoor/outdoor vertical conduit run where a junction box and/or pull point is unavailable. Meets NEC Section (A) requirements for intermediate supports at midpoints in vertical conduit risers. Requires less space in conduit run than rectangular junction box. May be mounted side-by-side or staggered in multiple conduit runs. Type W cable support is essentially a modified type R cable support mounted within a pull box fitting. Lay-In-Lug grounding lug can be mounted on pull box end fitting. Cable support body and pull box end fittings: malleable or ductile iron Oversize sleeve: steel Hot dip galvanized finish Optional Material Cable support body and pull box fitting: available in cast aluminum. Add suffix -A to catalog number. Example: W-1508A-1-OS. Options For Lay-In-Lug, see O-Z/Gedney Lay-In-Lug Grounding Lugs for use with cable supports. Illustrated Existing Conduit Oversize Sleeve Type R Cable Support Set Screws Existing Conduit COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS Conduit Size Fitting With Sleeve Fitting Without Sleeve 5 or More Wires or Different Fitting With Sleeve Sleeve Furnished With Fitting Fitting Without Sleeve Trade Size Length Dimensions in Inches/Millimeters Length Maximum Fitting Closed 1-1/2 W OS W LS W OS W LS 2.50/ " 3.38/ / W OS W LS W OS W LS 3.00/ " 4.00/ / /2 W OS W LS W OS W LS 3.50/ " 4.63/ / W OS W LS W OS W LS 4.00/ " 5.13/ / /2 W OS W LS W OS W LS 4.50/ " 5.75/ / Fitting Open (Min.) L Commercial Products 4 W OS W LS W OS W LS 5.00/ " 6.25/ / W OS W LS W OS W LS 7.00/ " 8.38/ / W OS W LS W OS W LS 8.00/ " 9.50/ /
17 G: Lay-In-Lug Grounding Lugs for use with Cable Supports Factory Installed. For mounting on O-Z/Gedney fittings. Copper Plus Lay-In-Lug Grounding Wire Connectors. Commercial Products COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS s Provides a compact means of attaching a grounding or bonding conductor to an O-Z/Gedney fitting. Highly conductive tin-plated copper saddle for use with copper or aluminum conductors. Connector opening allows easy insertion of grounding conductor for thru or end connection. Low grounding connector profile. Spring action design maintains positive firm contact on grounding conductor. These grounding wire connectors are used on the specification insulated grounding bushings. Grounding lugs not sold separately. Grounding Saddle/Tin Plated Copper Clamping Tension Body/Stainless Steel Screws/Stainless Steel UL Standard: 514B, 467 UL Listed: E24264 CSA Standard: C22.2 No. 18, 41 CSA Certified: Note: 1. Type G Grounding Lugs are only furnished factory-mounted to O-Z/Gedney fittings. 2. Grounding Lugs are not sold separately. 3. Type G Grounding Lugs are not compatible with all O-Z/Gedney fittings in this catalog. Please review specific fittings catalog page to insure compatibility. If unsure, please contact your local representative before ordering. Grounding Min. Wire Size Max. Lug Rating Mounted on Cable Support Trade Size Mounted on PK Clamp TO ORDER: Place the order for each grounding lug on the next order line immediately after the fitting that the lug will be attached to. See Note prior to ordering. Ordering Example: Item # Quantity Part Number Description 1 5 PK-200 Cable Termination 2 5 G-04S Grounding Lug Part Number 14 4 CU only 1/2 6 G-04S 8 2/0 AL-CU 1/2 6 G-22S 6 4/0 AL-CU 2-1/2 6 G-24S CU only 2-1/2 6 G-25S Solid or stranded for No. 4 AWG or smaller; stranded for No. 2 or larger Indicates trade sizes of fitting to which grounding wire connector can be mounted. 1618
18 dozseal Sealing Insulating Compound For Use in Terminators, Compound Bushings and Compound Type Cable Supports dozseal 220 Used in gasketed or threaded splice fittings and gasketed terminators. Used in non-hazardous location with any cable having solid type insulation, such as Paper, Varnished Cambric, Rubber, Butyl, Cross-Linked Polyethylene, or High Molecular weight Polyethylene rated 34.5KV and below. dozseal 225 Used in gasketed or threaded splice fittings and gasketed terminators, when they are installed in hot climates or in hot exposures. Used in non-hazardous location with cables having solid type insulation, such as Paper, Varnished Cambric, Rubber, and Butyl rated 34.5KV and below. dozseal 230 Used in non-gasketed terminators or cable supports. Used in non-hazardous location with any cable having solid type insulation. dozseal 220 Having a low softening point and low pouring temperature The compound remains plastic at low temperatures and remains viscose at the highest cable operating temperature. dozseal 225 Having a medium-low softening point and a low pouring temperature. The compound remains plastic at medium-low temperatures and remains more viscose at the highest cable operating temperature. dozseal 230 Having a high softening point and high pouring temperature. The compound remains plastic at the highest cable operating temperature. Material dozseal 220 Universal medium-soft asphaltic base compound dozseal 225 High ambient medium-hard asphaltic base compound dozseal 230 Hard asphaltic base compound COMMERCIAL PRODUCTS: RIGID AND IMC FITTINGS Compound Number Type Catalog Number One Qt. Can One Gallon Bucket Five Gallon Bucket For Use In Terminators, Compound Bushings, Compound Type Cable Supports dozseal 220 Medium-soft asphaltic base DOZ-220Q DOZ-220G DOZ-220G5 dozseal 225 Medium-hard asphaltic base DOZ-225Q DOZ-225G DOZ-225G5 dozseal 230 hard asphaltic base DOZ-230Q DOZ-230G DOZ-230G5 Commercial Products Characteristics Unit dozseal Filling Compounds dozseal 220 dozseal 225 dozseal 230 Softening Point F Pouring Temperature F Flash Point F Dielectric Strength KV For shipping purposes, the approximate gross weight of the above compounds is 10 lbs. per gallon. When ordering compound specify by number of units only, not quarts or gallons. Example: To order 50 gallons of dozseal 220 specify ten (10) DOZ-220G5 units. 1619
Cable Supports. Requirements for Cable Supports in the National Electrical Code reads as follows:
QA1 General Information are used to support cables in vertical raceways or risers. Cable supports relieve the strain that would be placed on terminations, the interior of panels, or other devices to which
More informationAll work must conform to the National Electric Code, latest edition, and all other applicable codes and regulations.
DIVISION 16 ELECTRICAL SECTION 16100 - ELECTRICAL PART 1 - GENERAL SCOPE All electrical work as shown on the drawings and as necessary to provide a complete electrical system. Include primary service,
More informationIEEE POWER ENGINEERING SOCIETY CHICAGO CHAPTER THE OKONITE COMPANY WEDNESDAY JANUARY 11, 2006 JIM FITZGERALD ENGINEERING LINGO
IEEE POWER ENGINEERING SOCIETY CHICAGO CHAPTER THE OKONITE COMPANY WEDNESDAY JANUARY 11, 2006 JIM FITZGERALD ENGINEERING LINGO WHEN YOU HEAR AN ENGINEER SAY A NUMBER OF DIFFERENT APPROACHES ARE BEING IMPLEMENTED
More informationTMC CableReady Connectors For Jacketed Metal Clad Cable TMC For Non-Hazardous Locations
TMC CableReady Connectors For Jacketed Metal Clad Cable TMC For Non-Hazardous Locations CableReady connectors are designed for use with the following cables: Type MC jacketed corrugated aluminum, interlocked
More informationELECTRICAL SERVICE REQUIREMENTS FOR MOBILE HOME DEVELOPMENTS
Prepared by: ABB1 ELECTRICAL SERVICE REQUIREMENTS FOR MOBILE HOME DEVELOPMENTS 052521 Asset Type: Electric Metering Function: Construction Issued by: Quoc Hoang (QxH1) Date: 07-01-16 Rev. #06: This document
More informationConduit Fittings & Accessories Directional Drilling Conduit Utility Duct Telephone Duct Residential Boxes
CANTEX INC. 301 Commerce Ste 2700 Fort Worth, Texas 76102 817-215-7000 Fax: 817-215-7001 Conduit Fittings & Accessories Directional Drilling Conduit Utility Duct Telephone Duct Residential Boxes YOUR FULL
More informationELECTRIC METERING COMMERCIAL & INDUSTRIAL
ELECTRIC METERING COMMERCIAL & 1.0 INDEX 1.0 INDEX 2.0 SCOPE 3.0 GENERAL REQUIREMENTS 4.0 METER LOCATIONS 5.0 UNDERGROUND TERMINATIONS 6.0 METERING TRANSFORMER ENCLOSURES 7.0 SINGLE CUSTOMER METER INSTALLATIONS
More informationGUE, GUB Junction Boxes
E GUE, GUB Junction Boxes Cl. I, Div. & 2, Groups B, C, D Cl. II, Div., Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III NEMA 4*, BCD, 9EFG Ex d IIC T6, IP66 Ex d IIC, IP66, ATEX certified Explosionproof
More informationTS 813 GROUNDING AND BONDING TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET GROUNDING
TORONTO TRANSPORTATION January 2012 TS 813 GROUNDING AND BONDING TABLE OF CONTENTS 1. DRAWINGS TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET
More information26 0533 Raceway and Boxes for Electrical Systems Page 1 of 7
Last Update: November, 2015 A. Conduits: Consultant s Handbook Page 1 of 7 1. All conductors for each and every electrical system shall be installed in a raceway except communications and A/V systems which
More information14 PHOENIX CONTACT Courtesy of Power/mation. 1310 Energy Lane, Saint Paul, MN 55108. info@powermation.com - 800-843-9859 - www.powermation.
14 PHOENIX CONTACT PLUSCON circular is a circular connector for use in industrial automation. The range of design sizes available is varied, starting with the design sizes M5 to M8 and M1, for sensor/actuator
More information4 Installation Requirements
4 Installation Requirements 9 4.1 Code Reference The authority having jurisdiction should be referenced to determine what law, ordinance or code shall apply in the use of flexible duct. Ducts conforming
More informationOutdoor Use Waterproof I/O Connectors (Optical / Modular / Electrical) FO-BH, FO-BC, NT5, JN2 / W Series
COMPONENTS PRODUCT INFORMATION RoHS Compliant NEW Outdoor Use Waterproof I/O Connectors (Optical / Modular / Electrical) FO-BH, FO-BC, NT5, JN2 / W Series Optical FO-BH Series (Compact Type) CONNECTOR
More informationPPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES BUSHING WITH PLUG CONNECTION WITH OUTER CONE PPS CHARACTERISTICS The PPS bushing can be used as a fixed section for the entry of medium
More informationCDGRD-10. Grounding. Solutions For Comm/Data Applications
CDGRD-10 Grounding Solutions For Comm/Data Applications Overview & Table of Contents Cooper B-Line s Grounding products for rack & runway provide a complete solution for grounding metal supports. The offering
More informationpicomax The Pluggable Connection System
picomax The Pluggable Connection System TECHNOLOGY THIS SPECIALIZED CAN T MEET ALL REQUIREMENTS. YES IT CAN. CONTENTS picomax Pin spacing: 3. mm/0.138 in;.0 mm/0.197 in; 7. mm/0.29 in Versatile Pluggable
More informationExclude all sales to foreign countries and all sales or transfers to other divisions or plants of your company. Survey Form 3.3.
(703) 81-3200 Electrical Connector Section - Underground Distribution Type Cable Connectors and Accessories Voting Classification (8-CC-IV) Domestic Net Sales Billed of Connectors for Residential and Medium
More informationJOB or CUSTOMER: ENGINEER: CONTRACTOR: SUBMITTED BY: SPECIFICATION REF: QUANTITY TAG NO. MODEL NO. GPM FEET LEAD LENGTH COMMENTS.
Redi-Flo2, 2 Environmental Submersible Pumps MP1 Submittal Data QUANTITY TAG NO. MODEL NO. GPM FEET LEAD LENGTH COMMENTS Technical Data Motor Type: Water-Filled, variable speed submersible Maximum Fluid
More informationPump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling
Pump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling 250_P1 R10/7/2015 Copyright 2015 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More informationJames M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
More informationMini USB and USB 2.0-IP67 Connector System
Mini USB and USB 2.0-IP67 Connector System Section 12 Mini USB and USB 2.0-IP67 Connector System CONEC has added the Mini-USB connector. This Mini-USB IP67 receptacle and plug family, feature a bayonet
More informationSYSTEM 1850-SE SERVICE ENTRANCE CABLE SYSTEM
Pyrotenax SYSTEM 1850-SE SERVICE ENTRANCE CABLE SYSTEM Contents Introduction This section provides an overview of general circuit design considerations and installation guidelines for a Pyrotenax System
More informationSection 21. Telecommunication Hardware. www.geindustrial.com BuyLog Catalog 21-1
Introduction...21-1 Fiber Closure Hardware...21-2 Cable Location Surge Protectors...21-4 Introduction GE has been manufacturing Telecommunication Hardware products for over 20 years and has become a leader
More informationThe National Armored Cable Manufacturers Association Presents. Installation Standard for Types AC and MC Cables
The National Armored Cable Manufacturers Association Presents Installation Standard for Types AC and MC Cables An ANSI Standard Original document jointly produced by NECA and NACMA as Standard for Installing
More informationSECTION 15140 - PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More informationCONTENTS. Yale University Design Standards. Underground Electrical Duct Bank. A. Summary. B. System Design and Performance Requirements
16600 Underground Electrical Duct Bank This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications
More informationRESIDENTIAL ELECTRICAL REQUIREMENTS (REVISED 3/28/2008) PERMIT REQUIREMENTS:
RESIDENTIAL ELECTRICAL REQUIREMENTS (REVISED 3/28/2008) PERMIT REQUIREMENTS: Signed completed Electrical Permit application form. Minnesota law requires all electrical work is to be performed by licensed,
More information2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property
2014 NEC Guide Lines for Home Owner Doing Electrical Work on their Property A brief summary of the most used code references for residential wiring State of Idaho Division of Building Safety Electrical
More informationMueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source.
Mueller Pipe Repair Products Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. SERVICE SADDLES Mueller service saddles, available in bronze,
More informationHeating Cable. Construction
Mineral Insulated High Temperature A C Constant Wattage Series Resistance Heating Cable Sets Process Temperature Maintenance to F (593 C) Maximum Exposure Temperature 4 F (76 C) (Power Off) Corrosion Resistant
More informationThe MC Cable Revolution is Gaining Ground REMKE
The MC Cable Revolution is Gaining Ground June 2014 MC Cable Installation Continues to Improve with Advances in Materials and Fittings As the use of Metal Clad Cable grows, contractors are demanding better
More informationINSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
More informationSubmit shop drawings for equipment provided under this section Shop drawings shall indicate:
Section 16435 - SWITCHBOARDS Introduction Part 1 - General Reference The work under this section is subject to requirements of the Contract Documents including the General Conditions, Supplementary Conditions,
More informationFITTINGS: CAST DEVICE BOXES. Applications. Illustrated Features
and FD Cast Hub Device Boxes UNILETS for use with Threaded Rigid Conduit and IMC. All Device Boxes have Ridge Top Construction. Furnished with Internal Ground Screw. Fittings FITTINGS: CAST DEVICE BOXES
More informationREAD THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS MAY VOID YOUR WARRANTY!
READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS MAY VOID YOUR WARRANTY! The main power to any existing system must be disconnected prior to the
More informationHOUSTON COMMUNITY COLLEGE HCC ALIEF CAMPUS MAIN BUILDING, FIRST, SECOND & FOURTH FLOORS RENOVATION ISSUE DATE: 10.17.12
SECTION 27 05 26 - GROUNDING AND BONDING FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes grounding and bonding products, design requirements and installation for communications
More informationDIVISION 26 - ELECTRICAL SECTION 26 05 20 CABLES FOR INSTRUMENTATION
DIVISION 26 - ELECTRICAL PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Instrumentation Cables 1.02 SUBMITTALS A. Submit in accordance with requirements of Section 01 33 00. B. Product Data: Submit
More informationSECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Equipment
More informationHIGHLAND VALLEY SUPPLY, INC STANDARD TERMS AND CONDITONS OF SALE
Electrical Conduit & Fittings Catalog HIGHLAND VALLEY SUPPLY, INC STANDARD TERMS AND CONDITONS OF SALE Payment Terms: Payment terms are printed on every invoice. Invoices not paid in full by the net due
More informationLighting Packages. 230 VAC Fluorescent Enclosure Light:
Spec-00581 H763.422.2211 763.422.2600 Electrical Lighting Packages Electrical Lighting Packages PANELITE Enclosure Lights Overview FEATURES Slim profile allows light to be tucked up out of the way for
More informationPipe Repair Products A complete selection for all types of pipe
Pipe Repair Products A complete selection for all types of pipe Mueller Service Saddles Manufactured and tested in accordance with ANSI/AWWA C800 & NSF 61 certified. Mueller service saddles, available
More informationTECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR
TECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR 1.1.0 SCOPE : This specification covers design, manufacture, testing at manufacture s works before
More information2012 Edition Redbook 11.0 GENERAL DRAWINGS AND STANDARDS
2012 Edition Redbook 11.0 GENERAL DRAWINGS AND STANDARDS Minimum Vertical Clearances Above Ground and Roofs D1 Minimum Pool Clearances D2 Minimum Clearances of Wires Adjacent to Buildings and Other Structures
More informationOASIS-PLUS 120V READ ALL INSTRUCTIONS BEFORE OPERATING READ ALL INSTRUCTIONS BEFORE OPERATING OZONE IS A POWERFUL OXIDIZER AND MUST BE USED WITH CARE
OASIS-PLUS 120V INFORMATION & OPERATING INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE OPERATING READ ALL INSTRUCTIONS BEFORE OPERATING OZONE IS A POWERFUL OXIDIZER AND MUST BE USED WITH CARE 56041852 WARNING:
More informationMyers Hubs. The broadest, most complete offering for terminating Rigid/IMC to a box or enclosure
Myers Hubs The broadest, most complete offering for terminating Rigid/IMC to a box or enclosure Myers Hubs The Original! Often imitated, never duplicated! Available in a wide range of sizes, materials
More information800 Communications Circuits
ARTICLE 800 Communications Circuits INTRODUCTION TO ARTICLE 800 COMMUNICATIONS CIRCUITS This article has its roots in telephone technology. Consequently, it addresses telephone and related systems that
More informationSection 3510: Reclaimed water Pipes, Valves, and Appurtenances February 11, 2011
STANDARDS AND CONSTRUCTION MANUAL : Reclaimed water Pipes, Valves, and Appurtenances February 11, 2011 PART 1 - GENERAL 1.01 SCOPE OF WORK A. These specifications cover the pipes, fittings, and appurtenances
More informationCatalog May 2015. Cable Accessories < 1 kv
Catalog May 2015 Cable Accessories < 1 kv Table of content Cable Accessories 1 Cable Accessories 1 kv Product range 2 Universal cleats 3 List of content 4 Notes 5 We reserve the right to make technical
More informationINDEX. Sec. No. Items Page Nos.
INDEX Sec. No. Items Page Nos. 1. Types of Pipe............... MSSP- 2 2. Concrete Pipe............... MSSP- 2 thru MSSP-3 3. ABS and PVC Truss Pipe............... MSSP- 3 4. ABS and PVC Solid Wall Pipe...............
More informationSlimSeal SSL Connector. Now Available in 1 Position. Free Hanging Version
Now Available in 1 Position Free Hanging Version SlimSeal SSL Connector The SlimSeal SSL connectors are low profile, single row connectors developed for indoor and outdoor LED lighting applications. These
More informationGUIDELINES FOR WIRING SINGLE FAMILY DWELLING UNITS
GUIDELINES FOR WIRING SINGLE FAMILY DWELLING UNITS This guideline has been prepared to assist the owner/occupant of a single family dwelling with compliance to the requirements of the National Electrical
More informationElectrical Code Regulation
Electrical Code Regulation St. Clair County has adopted the 2005 National Electrical Code in its entirety for the unincorporated areas of the county and all communities that have contracted with the county
More informationEDS / EFS Series Control Stations
EDS / EFS Series Fully Assembled EFS and EDS Factory Sealed Devices NEMA, 7B*CD, 9EFG Applications: Factory sealed enclosures are installed in a rigid metallic conduit system for surface mounting adjacent
More informationGAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
More informationNEW SERVICE INSTALLATION STEPS. Common Slow Downs. Other Necessary Steps
NEW SERVICE INSTALLATION STEPS Here is the step-by-step process required to fulfill your service installation request. Please take a few minutes to review the steps, become familiar with key milestones
More informationSTABILOY BRAND FeeDeR SOLuTIONS
STABILOY BRAND Feeder Solutions DATA CENTER Introduction General Cable understands that data centers depend heavily on a steady, reliable and scalable source of power. That is why our STABILOY Brand aluminum
More information2a. IEM Indoor Metal Clad Medium Voltage Switchgear 15KV 16346-1. 2a. Section 16346 INDOOR METAL CLAD MEDIUM VOLTAGE SWTICHGEAR (Std.
2a. IEM Indoor Metal Clad Medium Voltage Switchgear 15KV 16346-1 2a. Section 16346 INDOOR METAL CLAD MEDIUM VOLTAGE SWTICHGEAR (Std. Relays) Part 1 General 1.1 CONDITIONS AND REQUIREMENTS: A. Refer to
More informationPlease check with your local inspection authority for any additional requirements before installation.
Specifications for Residential Overhead Electric Service Installation This brochure addresses most typical residential overhead service installations. Variances for the following specifications must be
More information08003-1 WATER SERVICE 2
08003_Mar08_2011.pdf Page 1 of 7 INDEX Page 08003-1 WATER SERVICE 2 1.1 Pipe 2 1.1.1 Copper 2 1.1.2 Polyethylene 2 1.2 Valves and Fittings 2 1.2.1 Main Stops 3 1.2.2 Curb Stops 3 1.2.3 Curb Box 3 1.2.4
More informationI N D U S T R I A L C A B L E G L A N D S
Introduction 1/2 Industrial Cable Gland W Industrial Cable Gland WL Heavy Duty Industrial Cable Gland CW Industrial Cable Gland CZ Industrial Cable Gland 1W Industrial Cable Gland 1Z Industrial Cable Gland
More informationSTABILOY BRAND FEEDER SOLUTIONS ASSISTED LIVING FACILITIES
STABILOY BRAND FEEDER SOLUTIONS ASSISTED LIVING FACILITIES Introduction General Cable understands that assisted living facilities require complex building designs that must address a wide range of systems
More informationSTABILOY BRAND FeeDeR SOLuTIONS
STABILOY BRAND Feeder Solutions DATA CENTER Introduction General Cable understands that data centers depend heavily on a steady, reliable and scalable source of power. That is why our STABILOY Brand aluminum
More informationDirectory chapter 02 - DIN Power (to 6 A) Types D, E, F, FM, 2F, F9, interface connectors I/U 02. 01. Technical characteristics types D and E... 02.
Directory chapter 02 - () Types D, E, F, FM, 2F, F9, interface connectors I/U Page Technical characteristics types D and E.............................. 02.10 Type D connectors.................... 02.11
More informationRE-ENTERABLE SPLICE CLOSURE KITS. (For Air Core None Pressurized Cable)
Triple T Broadband Public Co., Ltd. Outside Plant Standard Sector Specification No. OES-001-027-04 Issued: RE-ENTERABLE SPLICE CLOSURE KITS (For Air Core None Pressurized Cable) 1. SCOPE 1.1. This specification
More information8146/5 Series Breaker Panelboards
8146/5 Series Breaker Panelboards DISTRIBUTION BREAKER PANELBOARDS FOR HAZARDOUS & CORROSIVE ENVIRONMENTS Breaker Panels Features: Wide variety of Flameproof branch circuit breakers for Zone 1 & Division
More informationSECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 GENERAL 1.01 DESCRIPTION A. The work covered by this section of the Specifications includes all labor necessary to perform and complete such
More informationCT-02 CABLE TRAY SYSTEMS
CT-02 CABLE TRAY SYSTEMS SYSTEMS THAT MAKE SENSE Introduction B-Line Systems was formed in 96 and has over 30 years experience manufacturing cable tray systems in which it has grown to become the industry
More information4 Posiflow Proportional Solenoid Valves
4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/4" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Flow rate can also be regulated by a range of electrical inputs (sensors,
More informationFeed-through terminal blocks for high-current applications
596 PHOENIX CONTACT With the feed-through terminal blocks, you can freely select the connection technology. Choose between traditional screw connection, robust bolt connection, and convenient push-in connection
More informationSECTION 16402 UNDERGROUND ELECTRIC SERVICE
SECTION 16402 UNDERGROUND ELECTRIC SERVICE PART 1 GENERAL 1.1 SUMMARY A. Description of System 1. Furnish all labor, materials, and equipment for below grade work external to buildings as required, and
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationPump Specifications 2448LSG, 2448LSGX Series Omnivore 2HP Simplex Grinder Packages
Pump Specifications 2448LSG, 2448LSGX Series Omnivore 2HP Simplex Grinder Packages 2448LSG_P1 R4/2/2012 Copyright 2012 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More informationPowermate Range Pitch 7.62
owermate Range itch 7.62 in headers Socket connectors CB connection Solder connection SV 7.62/90 500 V / 43 A SV 7.62/180 500 V / 41 A.2.4 Cable connection Clamping yoke connection Tension clamp connection
More informationArktite Heavy Duty Circuit Breaking Plugs and Receptacles
1312-1313.qxp 12/16/2013 7:04 PM Page 1312 Arktite Heavy Duty Circuit Breaking Plugs and Receptacles Industrial Heavy Duty Non-hazardous Areas Features: Arktite circuit breaking plugs and receptacles are
More informationSPEEDFAX TM 2011 Load Centers & Circuit Breakers Contents
SPEEDFAX TM 20 Load Centers & Circuit Breakers Contents Load Centers ing System -2 Siemens PL and ES Series Load Centers Introduction -3 PL Series Load Centers Features and Product Offering -4-5 PL Series
More informationRequirements for the Attachment of Communication Cable Facilities on PPL Poles
Page 99 of 137 Requirements for the Attachment of Communication Cable Facilities on Replaces: URS-3002 URS-3004 URS-101C-304 A-157649 Page 100 of 137 Reference Notes for Drawings: General 1. The term communication
More informationONTRAC WIRE MESH CABLE TRAY SYSTEM
P R O D U C T D ATA S H E E T ONTRAC WIRE MESH CABLE TRAY SYSTEM K E Y F E AT U R E S Available in two styles: Shaped and Standard Tray Easy to use pathway solution that supports large quantities of network
More informationEast Central College 14434.03 HANSEN HALL LEVEL 300/400 RENOVATIONS PACKAGE
SECTION 260519 - BUILDING WIRE AND CABLE PART 1 - GENERAL 1.1 WORK INCLUDES A. Base and Alternate Bids: 1. Contractor Provide: a. Building wire and cable as shown on drawings or specified including feeders,
More informationMueller. Pipe Repair Products. A complete selection for all types of gas lines... all from a single source. GAS PRODUCTS DIVISION
Mueller Pipe Repair Products A complete selection for all types of gas lines... all from a single source. GAS PRODUCTS DIVISION MUELLER STAINLESS STEEL REPAIR CLAMPS Mueller offers a full line of stainless
More informationSECTION 25110 TELECOMMUNICATION ROOMS
PART 1 - GENERAL 1.1 SUMMARY A. SCOPE SECTION 25110 TELECOMMUNICATION ROOMS 1. This section includes the minimum installation requirements for equipment and cabling infrastructure in Telecommunication
More informationEDS / EFS Series Control Stations
EDS / EFS Series Control Stations Fully Assembled EFS and EDS Factory Sealed Devices Cl. I, Div. & 2, Groups B*, C, D Cl. II, Div., Groups E, F, G NEMA, 7B*CD, 9EFG Applications: Factory sealed enclosures
More informationMETER REQUIREMENTS GENERAL REQUIREMENTS SECTION D
12 - ELECTRIC SERVICE HANDBOOK SECTION D METER REQUIREMENTS This chapter gives you information on Central Lincoln s metering requirements. It's divided into three sections: General requirements This section
More informationSECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. The requirements for pipe material and installation in sewer and drainage collection systems. All materials
More informationHigh-Purity Fluoropolymer Fittings
High-Purity Fluoropolymer Fittings Hyper Fitting/Series LQ1, Work Procedure Instructions Insertion Tool The parts case is shipped together with the fitting jig. Refer to page 4 for How to Order. R type
More informationINSTALLATION & OPERATING INSTRUCTIONS
INSTALLATION & OPERATING INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER. THE UNIT SHOULD BE INSTALLED BY A QUALIFIED SERVICE REPRESENTATIVE.
More informationLOW-VOLTAGE TRANSFORMER QUICK START GUIDE PLANNING GUIDE INSTALLATION GUIDE
LOW-VOLTAGE TRANSFORMER QUICK START GUIDE PLANNING GUIDE INSTALLATION GUIDE Applies to Models: 75W, 150W, 300W, 600W, 900W, 1200W ATTENTION: Please read this guide carefully to ensure safe and efficient
More informationSOLAR PV STANDARD ELECTRICAL PLAN Microinverter Systems for Single Family Dwellings
*** Provide this document to the inspector along with ALL system installation instructions *** Project Address: Scope: Standard plan for the installation of grounded microinverter solar PV systems, not
More informationCable Accessories. for Extruded Dielectric Cable 69kV - 230kV Rated. Catalog Python13
Cable Accessories for Extruded Dielectric Cable 69kV - 230kV Rated Components used in cable systems 100% Tested Factory Molded For outdoor applications through 230kV For gas insulated substations and transformers
More informationUnarmored Variable Frequency Drive (VFD) Cable Termination Guide
Authorized Distributor Unarmored Variable Frequency Drive (VFD) Cable Termination Guide Be Certain with Belden A Step-by-Step Look at the Connection/Termination of Unarmored VFD Cables Terminating Unarmored
More information3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
More informationELECTRICAL GUIDELINES FOR SINGLE-FAMILY HOME OWNERS:
ELECTRICAL GUIDELINES FOR SINGLE-FAMILY HOME OWNERS: Chapter 12 of the Burlington Code of ordinances allows owner occupants of single family homes to do their own wiring if they choose. If you choose to
More informationCP2 Buried Cable Pedestal Initial & Rehab Installation Instructions
Printing 3 March 2008 CP2 Buried Cable Pedestal Initial & Rehab Installation Instructions This instruction is intended for CP2 cable pedestal installations and replacements. The following tools will be
More information25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp and 1250 Amp
Page 1 2015 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 15 kv or 25 kv Separable Insulated Connector (elbow) Equipment Connection Power Cable Power Cable Grounded Metal
More informationUGVCL/SP/591/11KV HT AB CABLE
TECHNICAL SPECIFICATION FOR 11KV AERIAL BUNCHED CABLES FOR OVERHEAD LINES (CROSSED LINKED POLYTHENE DRY GAS CURED) 1. SCOPE This specification covers requirements of XLPE insulated, 11 KV Aerial Bunched
More informationHose Clamps & Fittings
All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw
More informationPump Specifications 405 Series Commercial Drain Pump (High-Temp) 2 Solids handling
Pump Specifications 405 Series Commercial Drain Pump (High-Temp) 2 Solids handling 405_P1 R1/27/2012 Copyright 2012 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More informationGenerator DoCKInG StatIonS
Generator DOCKING STATIONS TRYSTAR Portable Power Cable Cam to cam cable extensions 2000V, 100A-400A rated to NEC table 400.5 (B) All portable power cable sold is highly flexible and UL & C-UL or CSA Listed
More informationAMPSEAL* Automotive Plug Connector and Header Assembly
AMPSEAL* Automotive Plug Connector and Header Assembly Application Specification 24 SEP 97 Rev E All dimensions are given in millimeters unless otherwise specified. All dimensional tolerances are +0.2
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationSECTION 15 AIR RELEASE VALVE ASSEMBLIES. 15-1 General
SECTION 15 AIR RELEASE VALVE ASSEMBLIES 15-1.01 Scope 15-1 General This section describes the requirements for furnishing and installing Air Release Valve Assemblies of the size and type shown on the plans,
More information