Experimental demonstration of OpenFlow-based control plane for elastic lightpath provisioning in Flexi-Grid optical networks

Transcription

1 Experimental demonstration of OpenFlow-based control plane for elastic lightpath provisioning in Flexi-Grid optical networks Jiawei Zhang, 1,3 Jie Zhang, 1,* Yongli Zhao, 1 Hui Yang, 1 Xiaosong Yu, 1 Lei Wang, 2 and Xihua Fu 2 1 State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, No.10 Xitucheng Road, Beijing, , China 2 Department of Researching, ZTE Corporation, No.55 South Keji Road, Shenzhen, , China 3 [email protected] * [email protected] Abstract: Due to the prominent performance on networking virtualization and programmability, OpenFlow is widely regarded as a promising control plane technology in packet-switched IP networks as well as wavelengthswitched optical networks. For the purpose of applying software programmable feature to future optical networks, we propose an OpenFlowbased control plane in Flexi-Grid optical networks. Experimental results demonstrate its feasibility of dynamic lightpath establishment and adjustment via extended OpenFlow protocol. Wireshark captures of the signaling procedure are printed out. Additionally, the overall latency including signaling and hardware for lightpath setup and adjustment is also reported Optical Society of America OCIS codes: ( ) Networks; ( ) Optical communications. References and links 1. M. Jinno, H. Takara, B. Kozicki, Y. Tsukishima, T. Yoshimatsu, T. Kobayashi, Y. Miyamoto, K. Yonenaga, A. Takada, O. Ishida, and S. Matsuoka, Demonstration of novel spectrum-efficient elastic optical path network with per-channel variable capacity of 40 Gb/s to over 400 Gb/s, in Proceedings of European Conference on Optical Communication (ECOC 2008), paper Th.3.F W. Wei, J. Hu, D. Qian, P. N. Ji, T. Wang, X. Liu, and C. Qiao, PONIARD: a programmable optical networking infrastructure for advanced research and development of future Internet, J. Lightwave Technol. 27(3), (2009). 3. H. Takara, B. Kozicki, Y. Sone, T. Tanaka, A. Watanabe, A. Hirano, K. Yonenaga, and M. Jinno, Distanceadaptive super-wavelength routing in elastic optical path network (SLICE) with optical OFDM, in Proceedings of European Conference on Optical Communication (ECOC 2010), paper We.8.D M. S. Moreolo, J. M. Fabrega, L. Nadal, and J. Vilchez, Software-defined optical OFDM transmission systems: Enabling elasticity in the data plane, in Proceedings of International Conference on Transparent Optical Networks (ICTON 2012), pp E. Mannie, ed., Generalized multi-protocol label switching (GMPLS) architecture, IETF RFC 3945 (2004), 6. L. Liu, T. Tsuritani, I. Morita, H. Guo, and J. Wu, Experimental validation and performance evaluation of OpenFlow-based wavelength path control in transparent optical networks, Opt. Express 19(27), (2011). 7. S. Azodolmolky, R. Nejabati, E. Escalona, R. Jayakumar, N. Efstathiou, and D. Simeonidou, Integrated OpenFlow-GMPLS control plane: an overlay model for software defined packet over optical networks, Opt. Express 19(26), B421 B428 (2011). 8. T. Nadeau, Software Driven Networks Problem Statement, draft-nadeau-sdn-problem-statement-01(2011), 9. L. Liu, R. Muñoz, R. Casellas, T. Tsuritani, R. Martínez, and I. Morita, OpenSlice: an OpenFlow-based control plane for spectrum sliced elastic optical path networks, in Proceedings of European Conference on Optical Communication (ECOC 2012), paper Mo.2.D F. Paolucci, F. Cugini, N. Hussain, F. Fresi, and L. Potì, OpenFlow-based flexible optical networks with enhanced monitoring functionalities, in Proceedings of European Conference on Optical Communication (ECOC 2012), paper Tu.1.D M. Channegowda, R. Nejabati, M. Rashidifard, S. Peng, N. Amaya, G. Zervas, D. Simeonidou, R. Vilalta, R. Casellas, R. Martínez, R. Muñoz, L. Liu, T. Tsuritani, I. Morita, A. Autenrieth, J.-P. Elbers, P. Kostecki, and P. (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1364

2 Kaczmarek, First demonstration of an OpenFlow based software-defined optical network employing packet, fixed and flexible DWDM grid technologies on an international multi-domain testbed, in Proceedings of European Conference on Optical Communication (ECOC 2012), Postdeadline paper Th.3.D J. Zhang, J. Zhang, Y. Zhao, H. Yang, X. Yu, L. Wang, and X. Fu, Experimental setup for OpenFlow-based elastic lightpath provisioning in Flexi-Grid optical networks, in Proceedings of European Conference on Optical Communication (ECOC 2012), paper P Introduction In order to effectively support diversity applications with a variety of QoS, the future optical network is evolving into a cost-effective architecture that can dynamically and flexibly adapt to upper services. The widely used of technologies such as Dense Wavelength Division Multiplexing (DWDM) and Reconfigurable Optical Add-Drop Multiplexers (ROADMs) have allowed service providers to increase the scale, flexibility, and reliability of optical networks. However, it is assumed that the current optical networks are still ossified or semi-flexible, having limitations to support new networking innovation technologies such as virtualization. Network virtualization, which is well known as a promising approach in the future network, have not yet been fully realized in optical network due to the rigid and fixed network architecture. Recently, the Flexi-Grid optical networks based on Orthogonal Frequency Division Multiplexing (OFDM) technology have been given extensive attention [1], which enables optical networks from rigid to flexible. To the benefit of OFDM modulation, high performance of spectrum efficiency is achieved, as well as the multi-access technology in physical layer by carrying the different user data over different subcarriers [2]. Additionally, adaptive modulation coding and elastic spectrum allocation are also introduced to enable the network architecture to be more flexible [3]. The above features enable segmentation and partitioning of the network infrastructure at layer 1, which is key enabler for network virtualization. Besides focusing on the improvement of network architecture, some device developers expect to promote the programmability in terms of transmission system and equipment in OFDM-based Flexi-Grid optical network by using software-controlled Field Programmable Gate Arrays (FPGA) [4]. From the service provider point of view, it is more suitable for realizing network virtualization in Flexi-Grid optical networks than in Fixed-Grid WDM optical network. The networking resource elements such as spectrum size, modulation format and central frequency of tunable laser and filter can be programmed and customized to satisfy the diversity of users demand. That means a real sliced spectral resource can be provided through a given elastic lightpath according to each specific purpose. This elastic optical network requires an intelligent physical layer control to meet the Spectrum-on-Demand (SoD) service, which poses a higher claim on the current control plane. Although GMPLS-based control plane [5] is a widely approved technology, it has some deficiencies due to the distributed nature, complex protocols and diffidence of service providers. Recently, Software Defined Network (SDN) and OpenFlow have become popular in optical networks [6, 7], which allow operators to control the packet and circuit switched networks by using a unified control plane. To the purpose of SDN/OpenFlow [8], the application can converse with and manipulate the networking resources from requesting the available resource in a specific way (e.g. OpenFlow protocol). It totally opens the variety of networking resources that enable services to use them intelligently and effectively. In additional, one controller with multi-switches architecture achieves good performance on lightpath provisioning latency compared with GMPLS-based control plane [9], but also brings higher requirement of processing ability for controller while networking topology and connection requests going large. The original motivation of SDN/OpenFlow which aims to develop a virtualized and programmable networking control meets the virtualization requirements of Flexi-Grid optical networks. Therefore, the combination of both technologies can achieve high performance on network, which has been becoming a hot topic in last two years [9 12]. In this paper, we present and experimentally demonstrate an OpenFlow-based control plane in Flexi-Grid optical networks. Dynamic lightpath establishment and adjustment (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1365

3 are implemented in our control plane testbed. The Wireshark captures of signaling procedure are printed out. Additionally, the overall latency including signaling and hardware for lightpath setup and adjustment are also reported. The rest of this paper is organized as follows. Section 2 proposes the enabling technologies of the OpenFlow-based Flexi-Grid optical networks. Section 3 presents OpenFlow-based elastic lightpath provisioning for time-varying traffic. Section 4 shows the experimental performance of our testbed. Section 5 concludes the whole paper by summarizing our contribution and discussing our future work on this area. 2. Enabling technologies of OpenFlow-based Flexi-Grid optical networks The use of OpenFlow in packet-switched network has been widely studied in protocol as well as device. In this section, we focus on some new features of OpenFlow enabling technologies which are exploited in the Flexi-Grid optical networks. Firstly, the difference of OpenFlow between packet-switched networks and circuit-switched networks is briefly pointed out. After that, OpenFlow-based bandwidth variable optical switch and main protocol extensions for Flexi-Grid optical networks are presented in detail. 2.1 OpenFlow in circuit-switched optical networks OpenFlow has originally been designed for packet-switched networks. In OpenFlow- based packet-switched networks, the first incoming packet will be encapsulated and sent to the controller. Controller returns a flow entry which is added into the flow table via Flow_mod message. The following packets (same flow) are forwarded directly by looking up the flow table of switch. Each switch which the packet passed will repeat the above processing one by one until the packet ends at the destination node. Compared with the packet-switched networks, there is a little difference in circuit-switched optical networks. Controller firstly calculates the path and reserves the resource along the path, and then sends flow entries to the corresponding switches simultaneously. Flow entry is just as a software command to trigger the action of switch. Once the lightpath is setup, it offers guaranteed performance to the transmitted data, since there is no packet processing and all data follow the same path. 2.2 OpenFlow-based bandwidth variable optical switch To control the optical nodes with OpenFlow protocol, we illustrate a functional diagram of OpenFlow-based Bandwidth-Variable Optical Switch (OF-BVOS) as shown in Fig. 1(a). In the switch, the OpenFlow switch software is embedded to keep the communication between controller and switch via OpenFlow Interface (OFI). The switch software receives the command (flow entry) from OpenFlow controller with the Flow_mod message and save it into the flow table. The OF-BVOS maintains flow table as software and translates the content to a programmable logic language which could be understood by hardware controller. This interworking is operated through Programmable Logical Interface (PLI). The function of hardware controller in Fig. 1(a) is used to realize the controlling of Bandwidth Variable Wavelength Cross-Connect (BV-WXC). The edge BV-WXC node which is equipped with Bandwidth Variable Wavelength Selected Switching [1] (BV-WSS) is shown in Fig. 1(a). The optical signal can be modulated to sub-carriers with any modulation format according to the requirement of traffic, and then launched by a tunable laser (T-LD) to the port of BV- WSS. This process can be manipulated by hardware controller through the Hardware Control Interface (HCI). In Fig. 1(a), OpenFlow switch software and hardware controller are implemented in a Linux PC, and BV-WXC is partly equipped with Finisar WaveShaper4000S which realize the flexible spectrum switching. The experimental details will be discussed in the Section 4. (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1366

4 Fig. 1. Extended OpenFlow for Flexi-Grid optical networks. (a) OpenFlow-based bandwidth variable optical switch. (b) Flow entry extension. (c) Flow entries for different nodes. 2.3 Extension of OpenFlow protocol for Flexi-Grid optical networks Extension of flow entry: In the packet-switched network, OpenFlow abstracts the data plane as a flow entry which can be defined as Rule, Action and Statistics [13]. It presents the packet s characteristic (IP address or TCP/UDP port) and the action of router or switch. The flow entry is also a key technology in the OpenFlow-based Flexi-Grid optical networks to control the optical flow. Figure 1(b) illustrates the extension option of flow entry for Flexi- Grid optical networks. As shown in Fig. 1(b), the Rules are extended as the In/Out Port, Central Frequency, Spectrum Size and Modulation Format which are the main characteristics in Flexi-Grid optical networks. The Action of optical node mainly includes four parts: Switch, Add and Drop to setup a lightpath, Delete to release a lightpath. Different combinations of Rules and Action are used to realize the control of optical transport node. Flow entries for different nodes of the path are given in Fig. 1(c). As shown in Fig. 1(c), in source node, a QPSK modulated optical flow with central frequency THz and spectrum size 50GHz is added in port 3 and out from port 4. The Statistics function is responsible for recording the optical flow property when the connection is setup. An option of flow property is to record the traffic rate information which aims to satisfy the dynamic Spectrum-on-Demand (SoD) service. Description of the main extended OpenFlow protocol: To satisfy the requirement of Flexi-Grid optical networks, we make some extensions to the current OpenFlow protocol [13], which is shown as follows: A. Packet_in message: is extended with two functions. One is to carry the lightpath request information which includes 32 bits Source/Destination addr and 16 bits Traffic rate and 32 bits Path ID. Additionally, it is also extended for returning a message to controller when OF-BVOSs complete the action. 32 bits Path ID and 8 bits Reason are extended to present the ID of a lightpath and the result of the (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1367

5 action to this lightpath (success or failure) respectively. The controller will judge which function the Packet_in message presents and give the corresponding respond to OF-BVOS. B. Flow_mod message: is extended for sending the lighpath setup/release commands to OF-BVOSs. The corresponding extensions involve of OFP_Match structure and Command field. For example, 32 bits Central frequency, 16 bits Frequency slot and 16 bits Modulation format are to present some features of lightpath in Flexi-Grid optical networks, which are implemented in structure OFP_Match. Add, Switch and Drop are actions which are implemented by extending Command field. The Match and Command information are collected by OF-BVOSs to control the lightpath setup and release. C. Stats_request/reply message: is extended for informing controller about the status of optical flow. Structure OFPST_Current_traffic is newly added in which 32 bits Path ID presents the ID of a lightpath and 32 bits Current traffic presents the current traffic rate of this lightpath. 3. Dynamic lightpath setup and adjustment by using OpenFlow protocol In this section, we present the signaling procedure for dynamic lightpath setup and adjustment for time-varying traffic in Flexi-Grid optical networks. Time-varying traffic is dominant in today s optical transport network, which the bandwidth between node pairs is varying over time. In WDM optical networks, a fixed channel (wavelength) is often provided for time-varying traffic, which leads to different bandwidth utilization in different time duration. Considering the benefit of Flexi-Grid optical networks, the spectrum size of optical channel can be flexibly provided according to the requirement of traffic. In this section, we realize the dynamic lightpath setup and adjustment by using extended OpenFlow protocol. Flow entry is updated by controller to trigger the action of switch. As described in previous section, the Statistics in flow entry can record the characteristic of traffic rate. When the traffic rate changed, OF-BVOS will send the spectrum adjustment information (Stats_reply message) to controller to generate a new flow entry. Then the controller will update the flow entry to the related OF-BVOSs to complete the spectrum adjustment. Fig. 2. Procedure of elastic lightpath provisioning. (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1368

6 Figure 2 illustrates a signaling procedure of elastic lightpath provisioning in OpenFlowbased Flexi-Grid optical networks. As shown in Fig. 2, traffic entering the Flexi-Grid optical networks is presented of time-varying feature. To effectively use the spectral resource, we can adjust the size of lightpath according to the requirement of traffic. The detailed descriptions of the procedure are summarized as follows: Step 1: OF-BVOS1 sends the connection request to the controller to establish a lightpath. Step 2: Controller performs RSA algorithm and returns a flow entry to the related OFBVOSs to trigger the switch action (via Flow_mod message). The lightpath is established. Step 3: Controller queries to OF-BVOS1 about the traffic rate (via Stats_request message). Step 4: When the traffic rate changed, OF-BVOS1 returns a message to controller to report the current traffic rate (via Stats_reply message). Step 5: Controller sends a new flow entry to OF-BVOSs to adjust the spectrum size of lightpath (via Flow_mod message). 4. Experimental setup, results and discussions We build a testbed with the topology as shown in Fig. 2. Two nodes (OF-BVOS1 and OFBVOS2) are equipped with Finisar WaveShaper4000S which has the ability to emulate the Flexi-Grid switching capacity. The Waveshaper4000S has 4-port switching functionality, making it possible to switch or combine multiple signals at different wavelength. The other nodes, both OF-BVOSs and controller are the embedded Linux PC platform, which are running in IBM server. We develop a hardware control program according to the API function of WaveShaper4000S to control the WaveShaper4000S as well as record the hardware adjustment latency. The process of hardware control program is shown in Fig. 3. Three different API functions are called to write filter profile into Waveshaper4000S. As shown in Fig. 3, the hardware control program can communicate with switch software and Waveshaper4000S through PLI and HCI respectively. In the experiment, time-varying traffic from OF-BVOS1 to OF-BVOS4 is established with spectrum size of 100GHz and then adjusted to 75GHz, 50GHz and 25GHz in three different time periods. The corresponding required numbers of frequency slots in WaveShaper4000S are 8, 6, 4 and 2 respectively (one frequency slot is 12.5GHz). The controller received connection request and performs RSA with shortest path routing algorithm. Fig. 3. The process of hardware control program. Figure 4 presents the whole signaling procedure for elastic lightpath setup and adjustment by using OpenFlow protocol. As shown in Fig. 4, denotes the IP address of controller, and , , and denote the IP address of OF-BVOS1, OF-BVOS2, OF-BVOS3 and OF-BVOS4 respectively. After receiving connection request from source OF-BVOS, controller performs RSA and then sends Flow_mod messages to the corresponding OF-BVOSs simultaneously (Process #1 in Fig. 4). Then OF-BVOSs will # $15.00 USD (C) 2013 OSA Received 1 Oct 2012; revised 3 Dec 2012; accepted 4 Dec 2012; published 14 Jan January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1369

7 return a success indicator and a lightpath ID via Packet_in message (Process #2). Message Stats_request (Process #3) is responsible for realizing lightpath adjustment by regularly querying OF-BVOS about the current traffic rate. Controller receives the responds from OF- BVOS via Stats_reply (Process #4) and then updates flow entries to corresponding OF- BVOSs via Flow_mod message (Process #5). Fig. 4. Wireshark capture of the signaling during the elastic lightpath setup and adjustment. Figures 5-9 illustrate the extended OpenFlow messages which correspond to Process #1 to #5 in Fig. 4, respectively. Figure 5 shows the extended Flow_Mod message which is sent to OF-BVOS2 ( ) to setup a lightpath. It can be found some extensions we made for Flexi-Grid optical networks including 32 bits Central frequency, 16 bits Frequency slot and 16 bits Modulation format which are marked with red dotted line. In Fig. 5, , and present a QPSK modulated lightpath with central frequency THz and spectrum size 100 GHz (8 frequency slots). Fig. 5. Wireshark capture of extended Flow_mod message for lightpath setup. Figure 6 illustrates the extension of Packet_in message. Packet_in message is the responds to controller when OF-BVOSs complete the action. 32 bits Path ID and 8 bits Reason are marked with red dotted line in which the and 02 present lightpath ID (#1) is successfully established. (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1370

8 Fig. 6. Wireshark capture of extended Packet_in message for lightpath setup. Figure 7 and Fig. 8 illustrate the Wireshark capture of the extended Stats_request/reply messages. 32 bits Path ID and 32 bits Current traffic are marked with red dotted line in which and denotes the lightpath ID (#1) and spectrum size (6 frequency slots) in its current stage. This session is initiated by controller and ended after receiving Stats_reply message from source OF-BVOS. Fig. 7. Wireshark capture of extended Stats_request message for lightpath adjustment. Fig. 8. Wireshark capture of extended Stats_reply message for lightpath adjustment. After receiving Stats_reply message, controller will update the OF-BVOSs flow entry to expand or squeeze the filter (Waveshaper 4000S) pass band according to current traffic (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1371

9 rate. Figure 9 illustrates the Flow_mod message which is sent to OF-BVOS1 ( ). Looking into the Frequency slot field, it is obviously to find that the amount of frequency slots have changed to 6 compared with initial lightpath size (8 frequency slots in Fig. 5). Fig. 9. Wireshark capture of extended Flow_mod message for lightpath adjustment. The spectrum sizes of time-varying traffic in different time periods, which can be reflected on the filter profile of WaveShaper4000S, are shown in Figs. 10(a)-10(d). The filter profile can be changed by updating the flow entry of OF-BVOSs. Figure 10(e) shows the flow entry of OF-BVOS2 after lightpath is successfully established and adjusted. The flow entry is translated to the language which can be understood by WaveShaper4000S. Fig. 10. Filter profiles and flow entry after lightpath is established and adjusted. We also measure the lightpath setup and adjustment latency in our testbed. The latency includes the processing latency in controller and OF-BVOS, signaling latency between controller and OF-BVOS, and the WaveShaper4000S response latency. The WaveShaper4000S response latency includes the API writing latency (API writes filter profile to WaveShaper4000S) and hardware latency. The WaveShaper4000S response latency can be measured in API software when API Call ends, which is shown in the left side of Fig. 3. Table 1 shows the setup and adjustment latency of lightpath in Figs. 10(a)-10(d). The mainly contribution of latency is the WaveShaper4000S response latency which is ranged from 420ms to 460ms in our testbed. It can be seen that, the setup latency (~521ms) is a little higher than adjustment latency, because the WaveShaper4000S will probably response a little slower when a large spectral region (100 GHz) needs to be updated (established). Note that, the value of latencies is not static. It depends on different conditions in network, such as the number of requests, the size of networking topology, the running time of RSA algorithm, and also the processing ability of controller and OF-BVOS. Table 1. The overall latency of lightpath setup and adjustment Lightpath OF-BVOS( ) # $15.00 USD (C) 2013 OSA Setup (a) ~521ms Adjustment (b) ~453ms Adjustment (c) ~464ms Adjustment (d) ~442ms Received 1 Oct 2012; revised 3 Dec 2012; accepted 4 Dec 2012; published 14 Jan January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1372

10 5. Conclusions In order to meet the requirements of flexibility and programmability of network resource for future optical networks, we present an OpenFlow-based control plane in Flexi-Grid optical networks and experimentally demonstrate the dynamic lightpath establishment and adjustment. The overall signaling procedure and main extended OpenFlow messages are printed out in this paper. Additionally, we verify the feasibility of dynamic adjustment of spectrum size by controlling of Finisar WaveShaper4000S via extended OpenFlow protocol. The adjustment latency including the signaling latency and hardware latency is also evaluated. Our future works contain two aspects. One is to extend the control plane testbed to a large scale topology. Therefore, the scalability issues are going to be considered including the distributed multi-controller architecture and the communication between them. The other is to develop network virtualization strategy in Flexi-Grid optical network and experiment it in the OpenFlow-based control plane in our testbed. Acknowledgments This work was supported in part by 863 program (2012AA011301), 973 program (2010CB328204), NSFC project ( , , ), RFDP Project ( ), 111 Project (B07005) and the Fundamental Research Funds for the Central Universities (2011RC0406). (C) 2013 OSA 28 January 2013 / Vol. 21, No. 2 / OPTICS EXPRESS 1373