The application is now available in 8 languages. (German, English, French, Spanish, Italian, Russian, Dutch, Polish)

Size: px

Start display at page:

Download "The application is now available in 8 languages. (German, English, French, Spanish, Italian, Russian, Dutch, Polish)"

Cleopatra Watts
8 years ago
Views:

1 Product: Room Master, Premium Type: RM/S 2.1 Current application program: Room Master, Premium/2.5a ======================================================================================= to: Room Master, Premium/2.5a from: 03/ General The application is now available in 8 languages. (German, English, French, Spanish, Italian, Russian, Dutch, Polish) to: Room Master, Premium/2.5 from: 10/ Valves: The application does not detect short circuits and overloads. This has been fixed.

5a from: 03/2013 1. General The application is now available in 8 languages.

2 to: Room Master, Premium/2.4 from: 08/ Valve: The valve does not respond to fault in the control value. Heating: 1 bit status changes during control value cooling. PWM: the extra time for change the control value is incorrect. This has been fixed. 2. Room Scenario: The parameter Operating mode or 1 byte value send to thermostat" is changed in "1 byte value send". The currently option are no and value [ ]. Therefore also changed the communication object number 9.

PWM: the extra time for change the control value is incorrect. This has been fixed. 2.

3 3. Inputs: If the operating mode Blind sensor available, triggers the wrong room scenario. Furthermore, the operating mode sends more cyclical, although the "lock" is active. If the operating mode "dimming sensor" available, that sends continued cyclically although the "lock" is active. This has been fixed. 4. Blind output K: The blind output K sends after a reset no status end-positions. This has been fixed.

If the operating mode "dimming sensor" available, that sends continued cyclically although the "lock"

4 to: Room Master, Premium/2.3 from: 08/2012 The application program 2.3 has been used for internal use only. to: Room Master, Premium/2.2 from: 08/2012 The application program 2.2 has been used for internal use only.

5 to: Room Master, Premium/2.1 from: 07/ Room Scenario 3: The Event 2 started with a delay does not activate. This has been fixed. 2. Incorrect Time Interval: The time intervals concerned begin in each case with n x 145, s and are 2,27s long. The adjusted time within this range is max. 2,27s long. This has been fixed.

6 to: Room Master, Premium/2.0 from: 08/ General: The application program was revised regarding the pre-configuration. Here you find an overview, detailed information in chapter 5 of the product manual. 2. Function of the Room Scenarios With the innovative concept of the Room Master RM/S 2.1, it is possible to call the entire Room Scenarios with just one group address. The call of a Room Scenario can be undertaken both internally, e.g. via a binary input as well as externally, e.g. via a group address from reception. The recalled Room Scenario sets the outputs via KNX scenes. These can also be internally or externally called. After recall of a Room Scenario, all functions in the room, e.g. illumination, room supply, blinds, heating or ventilation, are adapted accordingly to the programming. The Room Master features internal device interconnections between the inputs and outputs. No group addresses are required for internal communication. This prevents an unnecessary bus load.

1, it is possible to call the entire Room Scenarios with just one group address. The call of a Room Scenario can be undertaken both internally, e.g. via a binary input as well as externally, e.g. via a group address from reception.

9 The standard functions of the Room Master are comprised of eight preconfigured Room Scenarios. All standard functions are activated immediately after the Room Master is connected: The room/apartment can be contacted directly by the RM/S via the outputs or via the bus. The RM/S can be contacted directly via the binary inputs or via the bus. Note The device is in a preconfigured state. During initial commissioning, it must be noted that most of the binary inputs are internally inhibited. Only the binary inputs Key card, Emergency, Window contact and Drip tray are functional. The inhibited inputs can be enabled as follows: By a telegram with the value 5 to the communication object no. 2 or Via the direct connection of the key card switch with the binary input p by introducing the key card. All pre-configuration information can be found in chapter 5 of the product manuals. To improve comprehension, the individual Room Scenarios will also be represented graphically. For this purpose, the following floor plan of a hotel room/apartment is used. TV Master

The RM/S can be contacted directly via the binary inputs or via the bus. Note The device is in a preconfigured state.

10 In the following table, you can see an overview of the preconfigured inputs and outputs and their connection. Input Connection Output a Master Room Scenario 7/8 b Bedside left Direct E (6 A) Bedside left c Bedside right Direct F (6 A) Bedside right d Main room 1 Direct G (6 A) Main room 1 e Main room 2 Direct H (6 A) Main room 2 f Hall Direct I (6 A) Hall f Hall On long operation T (6 A) Room service LED switches OFF g Bathroom Direct J (6 A) Bathroom h Blower bathroom Direct C (20 A/16 AX C-Load) Blower bathroom: Staircase lighting: 300 s i Emergency call Room Scenario 4 j Auxiliary electrical heater Direct D (16 A/10 AX) Auxiliary electrical heater k Drip tray Via bus: CO* to RDF/A l Floor/desk light Direct B (20 A/16 AX C-Load) Floor/desk light socket m Open blind Direct n Close blind Direct o Window contact Via bus: CO* to RDF/A K Blind p Key card Room Scenario 5/6 q Do not disturb Direct with short push q Do not disturb Direct with long push r Room service Direct with short push r Room service Direct with long push *CO = communication objects Special Room Scenarios S (6 A) S (6 A) T (6 A) T (6 A) Do not disturb LED switches ON Do not disturb LED switches OFF Room service LED switches ON Room service LED switches OFF Via Room Scenarios A (20 A/16 AX C-Load) Socket switched Via RDF/A L, M, N O, P, Q, R Fan 1, 2, 3 Valve 1 4 Via Room Scenarios U Room occupied

Direct H (6 A) Main room 2 f Hall Direct I (6 A) Hall f Hall On long operation T (6 A) Room service LED switches OFF g Bathroom Direct J (6 A) Bathroom h Blower bathroom Direct C (20 A/16 AX C-Load)

11 Further KNX devices can be integrated in the pre-configured standard functions. The Room Scenarios can also be adapted, and eight further Room Scenarios can also be set up. A total of 16 Room Scenarios can be configured. The 16 adjustable Room Scenarios are subdivided into groups of two, e.g. insert key card and remove key card or check in and check out. A Room Scenario, triggered by an external 1 byte telegram or internally via the binary inputs, can trigger up to seven communication objects. These communication objects control: The actual Room Master, e.g. internal switching of the outputs, External KNX devices in the room, e.g. RDF/A, External KNX devices in the building, e.g. reception.

A Room Scenario, triggered by an external 1 byte telegram or internally via the binary inputs, can trigger up to seven communication objects.

12 to: Room Master, Premium/1.0 from: 12/ General: Application program at time start of launch.

ABB i-bus KNX. Room Solutions. ABB STOTZ-KONTAKT GmbH - 2CDC 514 049 N0202, page 1

ABB i-bus KNX. Room Solutions. ABB STOTZ-KONTAKT GmbH - 2CDC 514 049 N0202, page 1 ABB i-bus KNX Room Solutions 2CDC 514 049 N0202, page 1 Room Master RM/S x.1 The Room Master RM/S 1.1 and RM/S 2.1 offers smart home and intelligent building control for hotel rooms and apartments Modern