User Guide. V 2 IU 5300-S Converged Network Appliance

Transcription

1 User Guide V 2 IU 5300-S Converged Network Appliance V7.2.2 May 2007

2 Trademark Information Polycom, the Polycom logo design, [and others that appear in your document] are registered trademarks of Polycom, Inc. [List other trademarks] are trademarks of Polycom, Inc. in the United States and various other countries. All other trademarks are the property of their respective owners Polycom, Inc. All rights reserved. Polycom Inc Willow Road Pleasanton, CA USA No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Polycom, Inc. Under the law, reproducing includes translating into another language or format. As between the parties, Polycom, Inc. retains title to, and ownership of, all proprietary rights with respect to the software contained within its products. The software is protected by United States copyright laws and international treaty provision. Therefore, you must treat the software like any other copyrighted material (e.g. a book or sound recording). Every effort has been made to ensure that the information in this manual is accurate. Polycom, Inc. is not responsible for printing or clerical errors. Information in this document is subject to change without notice.

3 Contents Introduction Introducing the V 2 IU 5300-S Converged Network Appliance Features Front Panel Management Features Installing the 5300-S Configuring the V 2 IU 5300-S Connecting to the 5300-S Logging In and Out of the 5300-S Navigating Through the Configuration Pages Read-only User Enabling a Read-only User Getting help Getting information about the network Routing Information Link Status Interface Information Getting information about the system System uptime Number of active streams Recent Call Log Process Information Memory Usage System Logging Messages Configuring Network Settings Configuring Subscriber Interface Settings Configuring Provider Interface Settings Subinterfaces

4 User Guide V 2 IU 5300-S Series Converged Network Appliances How Subinterfaces Works Configuring Subinterfaces ToS Byte Setting How the ToS Byte Setting Works Viewing or Changing the ToS Byte Setting Setting the Ethernet Link Rate Configuring the Network Configuring for Video H.323 Configuration H.323 Activity H.323 Alias Manipulation H.323 Neighboring Regular Expressions Forwarding Rules How Forwarding Rules Works Example Configuring Forwarding Rules Peering Proxy How Peering Proxy Works Configuring Peering Proxy Adding an H.323 Prefix Entry Clients List Lock Enabling the Clients List Lock H.323 Activity Monitor Type of Events Call Status Call Termination Viewing the H.323 Activity Monitor H.460 Operation Mode How H.460 Operation Mode Works Configuring the H.460 Operation Mode Configuring VoIP Overview Configuring VoIP Subnet Routing Deleting a VoIP subnet route Configuring VRRP

5 Contents Configuring the Firewall Configuring Basic Firewall Settings Basic settings rules Configuring Advanced Firewall Settings Advanced setting rules Enabling or disabling the firewall Administrative Options Changing the Administration Password Specifying User Commands Managing SIP, MGCP or H.323 Clients Selecting a client Deleting clients Querying clients Adding clients Restarting the Network Rebooting the System Using Network Test Tools Running a ping test Running a traceroute test Upgrading the Firmware Configuring a Management Interface Configuring the interface Reconnecting the 5300-S Figure 1. Move the connection from Port 2 to Port Configuring the Trusted Management Addresses Setting the Provider MTU Size Enabling SNMP Disabling SNMP Enabling remote system logging Disabling remote system logging Setting the System Date and Time Creating a Static Route Appendix Appendix 1 Troubleshooting Tips Appendix 1 Trouble accessing the Internet Appendix 1 No dial tone Appendix 1 Checking the ALG registration code Appendix 2 3

6 User Guide V 2 IU 5300-S Series Converged Network Appliances Telephone doesn't register with the softswitch Appendix 2 Checking the configurations on the ALG page Appendix 2 Pinging the softswitch Appendix 2 Regulatory Notices Regulatory Notices 1 END-USER LICENSE AGREEMENT FOR POLYCOM SOFTWARE. Regulatory Notices 1 FCC PART 15 NOTICE Regulatory Notices 11 Industry Canada NOTICE Regulatory Notices 11 4

7 1 Introduction Introducing the V 2 IU 5300-S Converged Network Appliance Installed at the edge of the operations center, 5300-S Series converged network appliances secure critical voice, video and data infrastructure components such as VoIP softswitches, video Gatekeepers, gateways and media servers. This chapter contains the following sections: Introducing the V 2 IU 5300-S Converged Network Appliance Features Front Panel Management Features 1-1

8 User Guide V 2 IU 5300-S Series Converged Network Appliance The 5300-S Series converged network appliances can be deployed in service provider or enterprise environments as depicted below. Service Provider H.323 Gatekeeper NMS Softswitch Gateway PSTN MCU ISDN, PSTN Network 5300-S Aggregation Router Hotspot NAT/Firewall Public IP Network PSTN SIP Voice User T-1/E-1 NxT-1/E T Company A Aggregation Router H.323 Video Endpoint Company B 5300-E Gateway V500 IP Phone Laptop IP Phone H.323 Video Endpoint EM008B 1-2

9 Introduction Headquarters PC H.323 Gatekeeper Application Server Softswitch NMS PC PC IP Phone PSTN Gateway 5300-S 5300-E IP Phone IP Phone Aggregation Router PSTN IP Network PSTN T-1/E-1 NxT-1/E-1 Gateway Branch Office 4300T H.323 Aggregation Router H.323 Endpoint Company B 5300-E Gateway IP Phone Laptop IP Phone PC EM009A The 5300-S is designed to protect managed VoIP service providers and enterprise customers from network-based attacks. It combines topology hiding, dynamic session admission control and stateful packet inspection to secure critical voice, video and data infrastructure components.this chapter introduces the: Functional features Hardware features Management features 1-3

10 User Guide V 2 IU 5300-S Series Converged Network Appliance Features Resolves firewall traversal problems at the Network Operations Center for VoIP by providing a VoIP application layer gateway (ALG) or voice and video aware firewall that supports SIP, MGCP and H.323 Resolves firewall traversal problems at customer offices for VoIP by providing NAT-Traversal capability for SIP. Supports up to 500 concurrent VoIP calls or up to 25 Mbps of H.323 video traffic. Protects the enterprise LAN using a stateful packet inspection (SPI) firewall for both voice and data traffic. Performs static IP routing. Provides integrated test tools to facilitate problem isolation. Performs TFTP relay for IP phone images. Uses a simple web based GUI for configuration and management. Supports logging to external syslog servers and interfaces to network management systems using SNMP. Front Panel The front panel of the 5300-S has the following ports: Port Subscriber (ETH0) Ethernet Port 1 Provider (ETH1) Ethernet Port 2 Out of Band Management Port 3 Console Port Description This port is a 10/100 auto sensing port. It is connected through an Ethernet switch to IP phones, IADs or PCs installed on the public network. This port is a 10/100 auto sensing port. It is connected to the private network. This port can be configured to allow out of band management sessions. It is typically connected to a private management network. This port is used to establish a local console session with the 5300-S using a VT100 terminal or emulation program. The baud rate is It is used for debug or local diagnostic purposes only 1-4

11 Introduction Management Features The 5300-S is configured and managed through the Configuration Menu, a web-based Graphical User Interface. Access the Configuration Menu by entering a URL in a web browser such as Internet Explorer, Netscape, or Firefox. Using the Configuration Menu, you can set a wide range of network services, including: Provider and subscriber settings and related network settings. Remote system logging. VoIP and subnet routing. Firewall Administration, maintenance and upgrading. The following chapters give you detailed processing steps you need to set up the 5300-S. 1-5

12 User Guide V 2 IU 5300-S Series Converged Network Appliance 1-6

13 2 Installing the 5300-S The 5300-S is designed for a 19-inch rack mount installation. Before installing, note the following cautions: Never assume that the AC cord is disconnected from a power source. Always check first. Always connect the AC power cord to a properly grounded AC outlet to avoid damage to the system or injury. Never place objects greater than 5 lbs on top of the 5300 as damage to the chassis may result. Ensure that the physical location of the installation has adequate air circulation and meets the minimum operating conditions as provided in the environmental specifications for the system. 2-1

14 User Guide V 2 IU 5300-S Series Converged Network Appliance 2-2

15 3 Configuring the V 2 IU 5300-S Configure the Polycom V 2 IU 5300-S using a web browser such as Internet Explorer or Netscape Navigator. The 5300-S is shipped with a pre-configured IP address for its Subscriber (Port 1) interface. This chapter includes the following sections: Connecting to the 5300-S Logging In and Out of the 5300-S Navigating Through the Configuration Pages Read-only User Getting help Connecting to the 5300-S You need to connect to the 5300-S before you can configure it to work with your network. Connect using the supplied preset IP address and subnet mask. You are also supplied with a default user ID and password. To connect to the 5300-S: 1. Connect a PC using an IP address of and subnet mask of to Port 1 of the 5300-S. 2. Launch a web browser on the PC and enter the URL string:

16 User Guide V 2 IU 5300-S Series Converged Network Appliance 3. Press Return. The Main Configuration Menu appears. 4. To log in, select Network from the navigation bar. 5. In the Connect to pop-up enter the following default information: For username: root For password: default Caution To maintain your network security, be sure to change the default username and password as described under Changing the Administration Password on page

17 Configuring the V 2 IU 5300-S 6. Continue to configure the system using the information provided in subsequent chapters of this guide. Logging In and Out of the 5300-S You are prompted to log in every time you point a new browser session to the Configuration URL. To log out, simply close your browser. Navigating Through the Configuration Pages Navigate through the configuration pages from the navigation bar. The choices are: 3-3

18 User Guide V 2 IU 5300-S Series Converged Network Appliance Menu Network VoIP ALG Firewall System Description Through the Network page, you can configure a wide range of multimedia network services. These services can be enabled or disabled depending on the functionality required for a network configuration. The device's network settings include configuring the Subscriber and Provider interfaces, DNS and Default Gateway. Using the VoIP ALG page, you can configure the connectivity and management for Subscriber and Provider voice and video over IP devices. Through the Firewall page, you can configure the 5300-S to act as a firewall for voice, video and data traffic. Through the System menu you have access to a variety of configuration operations and status information. Read-only User This feature works by creating a new user with read-only access to the system. All information is displayed in a non-changeable form. Information changed in entry boxes cannot be submitted. In fact, most Submit and OK buttons are not visible. Note: You must have administrator privileges and log in as an administrator to change read-only user. Enabling a Read-only User To enable a read-only user, use the following steps: 1. Using the configuration graphical user interface, from the Configuration Menu on the left-hand side, click Network. Note: You must have administrator access and log in as an administrator to change read-only user. 2. Scroll down to the area of the screen shown below. 3. Click changed. The following window screen appears: 3-4

19 Configuring the V 2 IU 5300-S Note: All open web browsers must be closed when you change between administrative user root and read-only rouser. 4. Enter a new password. The password must be a minimum of six characters long. 4. Re-enter the new password to confirm it. 5. Click Submit. Now when you access the system using this user name (rouser) and password, all fields are read-only. Getting help You can get help from several sources in the Configuration Menu. By pressing Help in the navigation bar. Following the link in Info at the top of the various Configuration pages. From the links on the Configuration Menu home page. Getting information about the network You can view a variety of information about the network from Network Information in the System menu. Networking Information displays the low-level IP network and interface configuration of the 5300-S. To view network information: 1. In the navigation bar, select System. 3-5

20 User Guide V 2 IU 5300-S Series Converged Network Appliance 2. In the System menu, select Network Information. 3. Scroll through the Network Information page to view: Routing information Link status Interface information Routing Information The system routing table contains the static routes for the hosts and networks that are on the Provider side of the 5300-S. When the provider and subscriber settings have been fully configured, there must be at least four routing lines displaying: The private subnet associated with the Provider interface. The immediate subnet associated with the Subscriber interface. The loopback interface. The network's default gateway, this must be the next-hop-router on the Subscriber side of the 5300-S. The order of the lines may vary depending on the subnet masks. Additional lines may be displayed depending on the contents of the Route and VoIP Subnet Routing pages. Each of the entries on these pages will cause an additional entry in the routing table. 3-6

21 Configuring the V 2 IU 5300-S Link Status Link Status displays the status of the Ethernet connections. Ethernet auto negotiation is often unreliable, especially between different vendors or old and new networking equipment. Failure of auto negotiation is generally not a cause for concern. However, if the negotiated rates change intermittently, or the link is down or there is no link, the link rate may need to be set manually on the Set Link Rate page. Intermittent data and voice outages may be caused by auto negotiation flutter. Setting the link rate manually is recommended and ensures that the device at the far end of the connection will not renegotiate rates during VoIP operation. Interface Information The specific status and configuration information for the system interfaces is displayed in the Interface Information section. The MAC address of interface eth0 is needed to retrieve the VoIP ALG License Key if the license information is lost. The interface statistics can point to areas of congestion in the network. If the errors statistic increase during normal operation of the device, it may be an indication of excessive congestion on the network interface. If the congestion is not corrected, the quality of voice calls will be affected. The topology of the network attached to the network interface with the errors should be examined and modified to better segment and isolate network traffic. See Link Status on page 3-7. Getting information about the system You can view a variety of information about the network from System Information in the System menu. System Information displays detailed information regarding the operating system running on the 5300-S. Customer support may ask you to examine or forward this information when troubleshooting problems with the 5300-S. To view system information: 1. In the navigation bar, select System. 3-7

22 User Guide V 2 IU 5300-S Series Converged Network Appliance 2. In the System menu, select System Information. 3. Scroll through the System Information page to view: System uptime Number of active streams Recent call log Process information Memory usage System logging messages System uptime System Uptime displays the current time, the amount of time elapsed since the last system reboot, and the system load averages for the past one, five, and 15 minutes. Uptime can help identify when a power outage may have interrupted service. Load averages greater than two indicate excessive system loading and could indicate over provisioning of the VoIP ALG feature. Number of active streams The number of active streams indicates how many calls are transiting the 5300-S (crossing from Subscriber to Provider interfaces) OR being hair-pinned by the 5300-S as part of its NAT-Traversal facility. Calls that are in progress and between two devices on one side of the 5300-S are not counted in this number. 3-8

23 Configuring the V 2 IU 5300-S Recent Call Log The Recent Call Log displays quality information about calls that are in progress or have recently completed. If a call falls below the configured MOS Threshold, a system log message is created. The MOS score for a call is always displayed when the call is completed. Detailed statistics for the call are reported in the Advanced MOS syslog message. Process Information Process Information displays detailed process table information that may be of use to technical support. Memory Usage Memory Usage displays detailed memory allocation information that may be of use to technical support. System Logging Messages System Logging Messages displays information logged during system boot and normal operation. Logging messages may indicate unauthorized attempts to access the 5300-S, process restart messages, and excess resource utilization messages. 3-9

24 User Guide V 2 IU 5300-S Series Converged Network Appliance 3-10

25 4 Configuring Network Settings This chapter describes how to configure the 5300-S network settings. It contains the following sections: Configuring Subscriber Interface Settings Configuring Provider Interface Settings Subinterfaces ToS Byte Setting Setting the Ethernet Link Rate Configuring the Network Before starting, collect the following information: An IP address for the 5300-S. An IP address for the gateway. The preferred and secondary IP address for the DNS server. The 5300-S is shipped with the preset subscriber (Port 1) IP address of: , and the default subnet mask: so you can access and configure the 5300-S. Configuring Subscriber Interface Settings The subscriber interface defines the interface between the 5300-S and your customers endpoints or the public network. 4-1

26 User Guide V 2 IU 5300-S Series Converged Network Appliance To configure subscriber interface settings: 1. In the navigation bar, select Network. \ 2. In Subscriber Interface Settings, highlight and replace the default IP Address and Subnet Mask. 3. If you are configuring network settings, see the instructions in Configuring the Network on page If you want to configure a management interface that is different than the default, complete all of the configuration tasks, then see Configuring a Management Interface on page Press Submit. Note After submitting the new configurations, you need to reconnect to the 5300-S using the new IP address and subnet mask before you can continue with the configuration. Configuring Provider Interface Settings The provider interface defines the interface between the 5300-S and internal voice, video and data devices. This interface is generally connected to the private network. 4-2

27 Configuring Network Settings To configure provider interface settings: 1. In the navigation bar, select Network 2. In Provider Interface Settings, select Static IP Address (the most common configuration), or DHCP if a DHCP server assigns the 5300-S internal address. 3. Enter an IP Address. 4. Enter a Subnet Mask. 5. If you are configuring network settings, see the instructions in Configuring the Network on page If you want to configure a management interface that is different than the default, complete all of the configuration tasks, then see Configuring a Management Interface on page Press Submit. Subinterfaces The Subinterfaces feature allows a system administrator to assign additional IP addresses to interfaces. These are sometimes referred to as aliases or loopback interfaces. An additional address may be assigned to the system s WAN interface to support, for example, another management IP address. 4-3

28 User Guide V 2 IU 5300-S Series Converged Network Appliance How Subinterfaces Works A common use for subinterfaces is forwarding a public subnet. A subinterface may be created to support a subnet forwarded through the Polycom V 2 IU 5300-S. When forwarding a subnet through the Polycom V 2 IU 5300-S, it is necessary to assign an address for this subnet to the system to act as the subnet's gateway. To configure forwarding rules, use the Forwarding Rules submenu under the Firewall configuration link. When applied to the WAN/Provider interface, these addresses are protected by the same firewall policy that is applied to the WAN/Provider address. Several other features in the system automatically create Subinterfaces. VRRP (if supported) and Static NAT automatically create Subinterfaces. When viewing the Network Information page, Subinterfaces are designated in the Interface Information section with the device name and number, separated by a colon (for example, eth0:100). Configuring Subinterfaces To configure subinterfaces, use the following steps: 1. Using the configuration graphical user interface, from the Configuration Menu on the left-hand side, click Network. 2. Click Subinterfaces. The window shown below opens. 3. On this screen, complete the following information: IP Address is the address to be assigned to the subinterface. 4-4

29 Configuring Network Settings Netmask is the network mask to use for the address. If several addresses are applied to an interface and these addresses are in a common network, they must use a common subnet. The system does not support supernetting. Interface is the port where the subinterfaces will be configured. 4. When you have finished entering this information, click Add. The following popup appears: 5. Click OK. The new subinterfaces entry appears on the Subinterfaces window in the list area. ToS Byte Setting Since the Internet itself has no direct knowledge of how to optimize the path for a particular application or user, the IP protocol provides a limited facility for upper layer protocols to convey hints to the Internet Layer about how the trade-offs should be made for the particular packet. This facility is the Type of Service or ToS facility. ToS settings allow the service provider to prioritize time sensitive traffic, such as voice plus video to ensure minimized packet loss and delay through their network. When providing end-to-end QOS, it is important that the voice plus video traffic be placed in the correct queues to deliver a higher QOS than regular traffic. Regular traffic, that is not time sensitive, can be delayed with little or no indication to the user, while the slightest delay in voice plus video can cause auditable differences. The ToS byte setting helps prioritize traffic going to the WAN so a provider can prioritize the traffic correctly in its network. Although the ToS facility has been a part of the IP specification since the beginning, it has been little used in the past. However, the Internet host specification now mandates that hosts use the ToS facility. Additionally, routing protocols (including OSPF and Integrated IS-IS) have been developed which can compute routes separately for each type of service. These new routing protocols make it practical for routers to consider the requested type of service when making routing decisions. How the ToS Byte Setting Works For all RTP traffic (voice and video), the Polycom V 2 IU 5300-S marks the ToS byte in the IP header as High Priority, and strips (set to 0) the ToS byte for all other traffic. Unchecking the Enable ToS Byte Stripping option means that the ToS byte will not be stripped from non-rtp traffic, but will remain unchanged. Note: For most situations, you should leave this setting as it is. Only change it if your provider indicates that you should do so. 4-5

30 User Guide V 2 IU 5300-S Series Converged Network Appliance Viewing or Changing the ToS Byte Setting To view or change the ToS byte setting, use the following steps: 1. Using the configuration graphical user interface, from the Configuration Menu on the left-hand side, click Traffic Shaper. 2. Scroll down the area of the screen shown below. 3. For most situations, you should leave this setting as it is. Only change it if your provider indicates that you should do so. If your provider indicates that you need to change the ToS byte setting, that provider should also provide the other parameters required on this screen. 4. If you have changed the values, click Submit to activate the new settings. Setting the Ethernet Link Rate Ethernet autonegotiation is often unreliable, especially between different vendors or old and new networking equipment. Failure of autonegotiation is generally not a cause for concern. However, if the negotiated rates change intermittently or the link is reported as no link or down, the link rate may need to be set manually. An interface that flutters because of the autonegotiation setting, may cause intermittent voice and data outages. Note The vast majority of Ethernet networking devices including the 5300-S use autonegotiate as a default setting. Chances are that you will not have to set the Ethernet link rate. Please use caution if manually configuring the link rate, as a speed or duplex mismatch will result in a loss of connectivity. If needed, configure the rate of the physical Ethernet port on the 5300-S. The default setting for the Ethernet port is autonegotiate, and it applies to both the link speed and duplex with locally attached devices. 4-6

31 Configuring Network Settings The link rate of an interface can be assigned to a desired rate. A network administrator may want to set the rate manually if autonegotiation fails to select a rate consistently or if it selects a rate that is slower than the maximum rate supported by both interfaces. To set the link rate: 1. In the navigation bar, select System. 2. In the System menu, select Set Link. 3. Select Subscriber Ethernet or Provider Ethernet. 4. Select the appropriate link rate for your Ethernet network (Note: If you set either 5300-S interfaces to 100FD, be sure you set the device at the other end of the line to 100FD also.): Setting 10baseT-HD 10baseT-FD Description 10Mbits per second using half duplex transmission 10Mbits per second using full duplex transmission 4-7

32 User Guide V 2 IU 5300-S Series Converged Network Appliance Setting 100baseT-HD 100baseT-FD Autonegotiate Description 100Mbits per second using half duplex transmission 100Mbits per second using full duplex transmission The 5300-S autonegotiates link rate and duplex with the directly attached device. 5. Press Submit. Configuring the Network Use network settings to configure the default gateway address, and the primary and secondary DNS servers. Packets destined for IP addresses not known to the 5300-S are forwarded to the Default Gateway for handling. For the 5300-S the Default Gateway MUST be the next hop router attached to Port 1 (the Subscriber interface). The primary DNS server is used by the 5300-S to resolve domain names to IP addresses. The secondary DNS server is used in the event the primary DNS server is unreachable. To configure network settings: 1. In the Network page, move to the Network Settings section. 4-8

33 Configuring Network Settings 2. Enter an IP address for the Default Gateway This must be the next-hop-router connected to Port 1, the Subscriber side interface 3. Enter the Primary DNS Server. 4. Enter the Secondary DNS Server. 5. Press Submit. 4-9

34 User Guide V 2 IU 5300-S Series Converged Network Appliance 4-10

35 4 Configuring for Video This chapter describes how to configure the Polycom V 2 IU 5300-S to support video: H.323 Configuration Forwarding Rules Peering Proxy Clients List Lock H.323 Activity Monitor H.460 Operation Mode 4-1

36 User Guide V 2 IU 5300-S Series Converged Network Appliance H.323 Configuration To access the H.323 Settings page, select VoIP ALG > H.323 in the Configuration Menu. 4-2

37 Configuring for Video The H.323 Settings page has the following areas: Gatekeeper Mode WAN/Provider-side gatekeeper mode settings LAN/Subscriber-side gatekeeper mode settings Embedded gatekeeper mode settings LRQ Size Default Alias Stale Time Multicast Messages 4-3

38 User Guide V 2 IU 5300-S Series Converged Network Appliance H Support Alias Restrictions In the Gatekeeper mode area, select one of the following modes: Item None WAN/Provider-side gatekeeper mode LAN/Subscriber-side gatekeeper mode Peering-Proxy mode Embedded gatekeeper mode Description H.323 is disabled. Specifies that the system will forward all client RAS messages to the gatekeeper. If this is selected, you must configure the settings in the WAN/Provider-side gatekeeper mode settings area. Specifies that the system will act as a gatekeeper. If this option is selected, you must configure the settings in the LAN/Subscriber-side gatekeeper mode settings area. Allows calls to be forwarded to other endpoints based on the information sent from the endpoints. All the information about routing the call must be sent as part of the request or prefixes must be configured. Provides gatekeeper functions and accepts endpoint registrations. If this option is selected, you must configure the settings in the Embedded gatekeeper mode settings area. If WAN/Provider-Side Gatekeeper mode is selected, you must configure the following parameters: Item WAN/Provider-side GK address Modify Time-To-Live New Time-To-Live Description Specifies the IP address of the gatekeeper Allows you to override the value for time-to-live returned by the gatekeeper before forwarding the response to the endpoint. Specifies how long an endpoint's registration should be valid. 4-4

39 Configuring for Video If LAN/Subscriber-Side Gatekeeper mode is selected, you must configure the following parameters: Item LAN/Subscriber-side GK address Allow public IP in LCF Description Enter the IP address of the gatekeeper. Select the checkbox if the gatekeeper has been deployed with multiple outbound proxies and must decide which proxy to use based on the IP address returned in the LCF. This is an advanced configuration option and should usually not be selected. If Embedded Gatekeeper is selected, you must configure the following parameters: Item Time-to-Live(s) Prevent calls from unregistered endpoints: Description Enter a time in seconds. This setting controls how long an endpoint s registration should be valid. At the end of this period the endpoint sends another registration request. Blocks unregistered LAN-side endpoints from making calls through the device. In the LRQ Size area, you can limit the number of source aliases in a forwarded LRQ message to a maximum of two to allow interoperability with gatekeepers that cannot handle more than two source aliases. In the Default Alias area, you can specify a default alias to be added to incoming calls without a destination message in the Q.931 Setup message. This alias allows the embedded gatekeeper or a LAN/Subscriber-side gatekeeper to route the call to a default endpoint. Enter a default alias and select one of the following types: E.164 H.323 In the Stale Time area, you can arrange to delete clients that have not sent any registration requests for the specified interval. This area includes the following configurable parameters: Item Delete stale clients Stale time (m) Description Select this checkbox to enable the stale timer feature. Specify the length of the interval in minutes. 4-5

40 User Guide V 2 IU 5300-S Series Converged Network Appliance Some RAS messages can be multicast in order to automatically detect gatekeepers. In the Multicast Messages area, you can enable listening to multicast messages. This area includes the following configurable parameter: Item Listen to multicast messages Description Select this checkbox to enable listening to multicast messages. In the H Support area, you can configure H support. This allows the system to do NAT/Firewall traversal for clients behind NAT or firewall devices. This area includes the following configurable parameters: Item Disabled Enabled Keep-alive time(s) Description Disables H support. Enables H support. Specifies the keep-alive time if H support is enabled. In the Alias Restrictions area, you can set a limit on the number of aliases that are allowed to register with the system. If this number is exceeded when a client tries to register, the registration is rejected. This area includes the following parameter: Item Max Aliases Description Enter the maximum number of allowed aliases. If the value is set to 0, the maximum is not enforced. The H.323 Settings page includes the following two buttons: Item Submit Reset Description Applies the settings configured on this page. Clears all fields and selections and allows you to enter new information. 4-6

41 Configuring for Video H.323 Activity To access the H.323 Activity page, select VoIP ALG > H.323 Activity in the Configuration Menu. The H.323 Activity page is a read-only page that shows the following information: Current time WAN Gatekeeper status Current payload bandwidth Estimated total bandwidth Activity log of recent H.323 events H.323 Alias Manipulation Alias manipulation is performed immediately when a message (such as an ARQ, LRQ or a Setup) is received. Any matching pattern is replaced with the specified string, allowing you to replace characters or strings that are hard or impossible to dial on certain endpoints. Normal call look-up is performed following alias manipulation. 4-7

42 User Guide V 2 IU 5300-S Series Converged Network Appliance To access the H.323 Alias Manipulation page, select VoIP ALG > H.323 >Alias Manipulation in the Configuration Menu. This page includes the following areas: Item Destination H323-ID or E.164 Alias Modification table Add a rule Description Lists alias manipulation rules. Rules are executed in the order in which they are listed. Use the arrows to move entries up and down, or use the Index field to specify where a new or edited rule falls in the list. Allows you to add new prefixes to the Prefix Routing and Gatekeeping Neighboring table. Item Action Pattern Index Replace Description Indicates whether the rule is to be added or edited. Specifies the pattern to be matched. See <l_link> Regular Expressions on page 11 for details on valid patterns. Determines the order in which the rule is scanned in the Destination H323-ID or E.164 Alias Modification table. To add a rule between two rules with consecutive indexes (n and m), use the higher index (m). Specifies the string that will replace the matched pattern. 4-8

43 Configuring for Video The H.323 Alias Manipulation page includes the following buttons: Item Commit Reset Description Applies the settings configured on this page. Clears all fields and selections and allows you to enter new information. H.323 Neighboring Neighboring and prefix routing can be used to route calls based on a matching prefix in the destination alias of the call. The call decision is made following alias manipulation and acts on the modified string, similar to other call lookup processes such as registered client look-up. Each prefix is associated with a domain name or IP address that is used in the event that the prefix matches. To access the H.323 Neighboring page (formerly the Prefix Routing page), select VoIP ALG > H.323 > Neighboring in the Configuration Menu. 4-9

44 User Guide V 2 IU 5300-S Series Converged Network Appliance This page includes the following areas: Item Prefix Routing and Gatekeeper Neighboring table Add a prefix Description Lists rules for forwarding incoming calls based on their dialed alias. Rules are executed in the order in which they are listed. Use the arrows to move entries up and down, or use the Index field to specify where a new or edited rule falls in the list. Allows you to add new prefixes to the Prefix Routing and Gatekeeper Neighboring table. Item Action Prefix Index Strip Add Neighbor Local Zone Address Description Indicates whether the rule is to be added or edited. Specifies the prefix pattern to be matched against the dialing string. See <l_link> Regular Expressions on page 11 for details on valid patterns. Determines the order in which the rule is scanned in the Prefix and Gatekeeper Neighboring table. To add a rule between two rules with consecutive indexes (n and m), use the higher index (m). Indicates whether the matching prefix is stripped from the dialing string. Specifies a string to be prepended to the dialing string. Determines whether a location request (LRQ) is sent when this prefix matches. If enabled, the prefix becomes a neighboring statement. If disabled, the incoming Q.931 Setup is forwarded to the given address without a preceding LRQ. This field is used for interoperability with other gatekeepers that may not accept a Setup without a preceding LRQ. Provides compatibility with remote gatekeepers that are configured to accept LRQs only from sources that match its configured remote zone. If a gatekeeper is configured to accept requests only from a known source, enter the zone in this field. Specifies the IP address or domain name of the device to which the call is to be forwarded. The H.323 Neighboring page includes the following buttons: Item Commit Reset Description Applies the settings configured on this page. Clears all fields and selections and allows you to enter new information. 4-10

45 Configuring for Video Regular Expressions Alias manipulation patterns and prefixes use regular expressions to match a string in the destination alias. A regular expression can be a string of literal characters to match or a set of special expressions. Alias manipulation patterns can match a sub-string at any location and number of times within the alias. Prefixes are always searched from the left of the alias and cannot match a middle part or the end of the alias. Regular expressions are listed in <l_link>table 1 and <l_link>table 2 lists some example expressions. Table 1 Regular Expressions Symbol Description. Matches any single character. [] Matches any single character listed between the []. For example, [abc], [123]. If the characters are separated by a -, all characters between the two are matching, e.g. [a-z], [0-9] () Matches the literal string given, e.g. (abc) Matches the block on either side of the, e.g. a b.? Matches 0 or 1 of the preceding block. * Matches 0 or more of the preceding block. + Matches 1 or more of the preceding block. \ Escapes the special meaning of the next character. {a} {a,} {a,b} Matches exactly 'a' numbers of the preceding block. Matches 'a' or more of the preceding block. Matches between 'a' and 'b' (inclusive) of the preceding block. Table 2 Example Regular Expressions Expression Description 100 Matches the string 100. (555)?123 Matches or 123. ( ) Matches 408 or [0-9]{3} Matches 555 followed by exactly 3 digits. # Matches the character '#'. \* Matches the character '*'. Note that '*' by itself is a regular expression and must therefore be escaped with a '\' to match the character itself. 4-11

46 User Guide V 2 IU 5300-S Series Converged Network Appliance Forwarding Rules Forwarding Rules allows a system administrator to forward data traffic for a subnet from one interface to another, overriding the Firewall s default drop rules. Allowing a subnet to be forwarded is commonly used when servers with public addresses are placed behind the system. Configuring the network in this way allows the system to manage and prioritize bandwidth, sharing it between the VoIP services and the servers. How Forwarding Rules Works When forwarding, one address from the forwarded range of addresses must be assigned to the rule's output interface. The Polycom V 2 IU 5300-S uses this address to act as a gateway router for the subnet. The address may be assigned using the Subinterfaces page. Note: The subnet and forwarded addresses are not protected by the firewall. A similar method for forwarding traffic is provided by Proxy ARP. Proxy ARP is used to bridge addresses within a single subnet range from one interface to another. Often this is used to bridge and forward a public address to the protected side of the system without having to subnet the public address range. Proxy ARP does not require an additional gateway address on the system for the subnet, but does not allow port and protocol filtering for forwarded data. Example In this example: The ISP has supplied two separate subnets to the customer: A small one (2 hosts) for the WAN link A large one (254 hosts) for a bank of servers is the WAN IP address for the Polycom V 2 IU 5300-S NAT is a private IP range of xxx using the WAN address for PCs and Phones On the LAN side of the Polycom V 2 IU 5300-S are the following: Private IP subnet ( xxx) Public IP subnet ( xxx) This is shown below. 4-12

47 Configuring for Video Configuring Forwarding Rules To configure address forwarding rules, use the following steps: 1. Using the configuration graphical user interface, from the Configuration Menu on the left-hand side, click Firewall. 2. Click Forwarding Rules. The window shown below opens. 4-13

48 User Guide V 2 IU 5300-S Series Converged Network Appliance 3. On this screen, complete the following information: IP Subnet: The subnet to be forward through the firewall from the Input Interface to the Output Interface. Netmask: The network mask to apply to the IP Subnet to create the range of IP addresses that are forwarded through the firewall. Input Interface: The interface where data is received that is destined for the forwarded subnet (destination address(es)). Output Interface: The interface where data is received that is sent from the forwarded subnet (source address(es)). Protocol: The following protocols are used: UDP: for the specified network, allows the specified UDP port or port range to pass through the system TCP: for the specified network, allows the specified TCP port or port range to pass through the system 4-14

49 Configuring for Video Any: for the specified network, allows all ports and protocols through the system. No ports are required because not all protocols support the concept of ports. Port or Port Range: The port number or port range allowed through the system when UDP or TCP are selected. A port range is specified by separating the starting and ending ports with a colon ':' (for example, 22:80). The ports parameter is not supported when you select Any protocol because not all protocols support the concept of ports. 4. When you have finished entering this information, click Add. 5. Click OK. The new forwarding entry appears on the Forwarding Rules window in the list area. Peering Proxy H.323 prefixes can be used to route calls based on a matching prefix in the destination alias of the call. Each prefix is associated with a domain name or IP address to send the call to in case the prefix matches. The prefixes are searched in order, that is, the first prefix is tried first, and then the next one on the list until the system finds a matching prefix. This means that if there are multiple matching prefixes, the first one is used. How Peering Proxy Works The Polycom V 2 IU 5300-S supports the concept of an H.323 Peering Proxy. This function provides advanced security layers or peering points within the network where a security layer is needed. Peering Proxy allows network providers to add internetworking connections between their trusted network and an unknown network. This topology hides their trusted network and the Stateful packet inspection Firewall provides the policies to ensure security. You can add Peering Proxies in series with one another to push the core H.323 networking infrastructure to meet individual security requirements. The illustration below shows a sample diagram with dial plan and call flow examples. It is a snapshot of how the Peering Proxy can be deployed. Peering Proxy however, is not limited to this specific scenario, so contact your Polycom representative to discuss specific network requirements for full Peering Proxy support. 4-15

50 User Guide V 2 IU 5300-S Series Converged Network Appliance Note: A minimum configuration for Peering Proxy would be for inbound only prefixes, since there may be many endpoints to statically route calls to. There might also be a master gatekeeper to which all endpoints are registered. In this case, you would only need 1 prefix pointing to the master gatekeeper and let that gatekeeper signal the other endpoints directly. In the example above, the Polycom V 2 IU 5300-S Peering Proxy is installed in Private Video Network A and B, a peering point into this network. This network could have additional peering points to allow topology spreading of network resources. However, this example shows only a single point. Peering 4-16

51 Configuring for Video Proxy provides an access point into this network and is responsible for the E.164 dial plan using NANP (North American Numbering Plans or NPAs). The NPAs in this case are 831 and 408. Dial plan integrity is required to insure proper routing of prefix's. This means that if users are to dial into your network, they could be required to enter a Prefix on their V 2 IU with a corresponding destination IP. If the user was to dial another user NOT destined to your network with the same beginning prefix, the prefix configured on this V 2 IU would create a prefix match and the call would route incorrectly. The call routes to the destination defined in the prefix and not to the intended endpoint. The example shows Private Video Network A's Peering Proxy with an inbound prefix defined as 8315 Any inbound call that matches 8315 with any 6 digits creates a prefix match and sends the call to Refer to Regular Expressions in the Info button on the GUI interface for information on all the methods for defining prefixes. Private Video Network A is one example of a V 2 IU configured in LAN Side Gatekeeper mode with an ANNEX O dial method to dial Off Net. Internal On Net endpoints registered to the LAN Side Gatekeeper will dial E.164 only. This allows any location to place calls to any location with an ANNEX O dial plan, that is, E.164@WAN_IP or other V 2 IU's deployed on the network. In this example a Peering Proxy has been deployed to allow dialing ingress and egress to the Public Internet. At each V 2 IU location required to egress, the Public Internet requires a Prefix to be configured. This allows that location's endpoint to dial Off Net to the Public Internet. This prefix can be configured to any digit and may be part of the externally dialed E.164 in the E.164@WAN_IP, that is, to reach site A by dialing @ where the prefix is defined as 415* or 415. In this example, a 9 was chosen. The prefix is then mapped to the LAN interface of the Peering Proxy The dial string is now @ and a strip rule for the prefix is applied. This is needed to route the call at the destination correctly. If the Site C V 2 IU does not strip the 9, the destination V 2 IU fails the call with a No Registered Client message (call failures can be viewed under the H323 Activity page in the GUI), since the 9 becomes part of the E.164. If you choose a prefix that matches the destination E.164, set Site C's V 2 IU to NOT strip matching prefixes. NOTE: In this illustration E.164@WAN_IP was used as an example. Peering Proxy and all V 2 IU's support user@host ANNEX O dialing methods, for example 123@ or abc@ or abc@abc.com with a DNS SRV record configured to point to an A record for the WAN IP of the V 2 IU. The following sections demonstrate the Dial Plan for ingress and egress calls to Private Video Network A as shown in the illustration. Outbound from Site C to Site A Site C dials an endpoint located at Site A: @ The PathNavigator receives the call and generates a Q.931setup to the V 2 IU for that subnet. The V 2 IU processes the Q.931 setup from the calling endpoint. The V 2 IU looks for a prefix match. In this case, the 9 creates a match. The Strip Matching Prefix rule is applied, the 9 is stripped, and the call is routed to 4-17