Repair of damaged rotor journal portion

Size: px
Start display at page:

Download "Repair of damaged rotor journal portion"

Transcription

1 CT-S-025 (1/6) Mar. 7, 2012 CT-S-025 / Repair of damaged rotor journal portion REASON FOR SUGGESTION: A turbine rotor journal portion may have its surface damaged during operation about 0.3mm in depth for the maximum and the damage interferes with operation. The repair is highly desirable because the rotor is expensive and has long delivery time to do the replacement. When the damage depth is lower than 0.2mm, repair can be done by chrome plating. But when the damage depth exceeds 0.2mm, plating thickness becomes 0.3mm, considering grinding margin. At this thickness, chrome plating becomes easy to flake off because of the increase in plating residual stress. Conventionally, we have repaired deeply damaged rotor journal portion by under-sizing the journal diameter. However, interchangeability with the spare rotor journal bearing disappears for this case, and the customer will have difficulty in inventory control. Moreover, the necessity for stocking special sized bearing arises. To avoid such a trouble, we researched repairing technology for the turbine journal portion that can be applied to the rotor with the blades installed. As a result, we established the repair technology by High Velocity Oxygen Fuel (HVOF) coating. DETAILS OF SUGGESTION: The outline of repairing is as follows. 1) High Velocity Oxygen Fuel (HVOF) coating can repair damaged rotor journal portion without under-sizing the journal diameter. 2) Anti-erosion property of HVOF coating was verified to be better than base material. 3) Reliability of HVOF coated rotor was confirmed by actual loading test.

2 CT-S-025 (2/6)

3 CT-S-025 (3/6)

4 CT-S-025 (4/6)

5 CT-S-025 (5/6)

6 CT-S-025 (6/6)

Ansaldo Thomassen Gulf. Ansaldo Energia Group. We Set Power in Motion

Ansaldo Thomassen Gulf. Ansaldo Energia Group. We Set Power in Motion Ansaldo Energia Group We Set Power in Motion We re OSP. We set power in motion. The power of thought is a remarkable thing. A brilliant mind can easily generate great ideas. Like service solutions that

More information

Your Service Partner Avonmouth and Bristol Service Centres

Your Service Partner Avonmouth and Bristol Service Centres Your Service Partner Avonmouth and Bristol Service Centres The Sulzer Advantage Avonmouth Service Centre Bristol Service Centre Capabilities Manual machining CNC machining Pump services Thermal spray

More information

TECHNICAL SPECIFICATIONS FOR BARE LINEPIPE FOR FIREWATER SERVICE

TECHNICAL SPECIFICATIONS FOR BARE LINEPIPE FOR FIREWATER SERVICE TECHNICAL SPECIFICATIONS FOR BARE LINEPIPE FOR FIREWATER SERVICE A) IS: 3589 GRADE FE 330 This tender specification establishes the minimum requirements for the manufacture of IS: 3589 Grade Fe330 Bare

More information

TECHNICAL RECOMMENDATIONS

TECHNICAL RECOMMENDATIONS ABRASION RESISTANT STEEL TECHNICAL RECOMMENDATIONS HIGH YIELD STRENGTH STEEL ABRASION RESISTANT STEEL HIGH YIELD STRENGTH STEEL GENERAL INTRODUCTION Quard is the brand name of the product group of abrasion

More information

TYPE APPROVAL CERTIFICATION SCHEME MASS PRODUCED DIESEL ENGINES

TYPE APPROVAL CERTIFICATION SCHEME MASS PRODUCED DIESEL ENGINES 1. Introduction TYPE APPROVAL CERTIFICATION SCHEME MASS PRODUCED DIESEL ENGINES 1.1 This scheme details the tests and inspection of diesel engines manufactured by mass production system for use in marine

More information

Global Service for Turbomachinery SERVICES

Global Service for Turbomachinery SERVICES Global Service for Turbomachinery SERVICES Comprehensive Quality Service With more than a century of turbomachinery experience and a tradition of excellence, Elliott offers a single, comprehensive source

More information

Garrett. GT/VNT15-25 Type Turbos. Version 7.0

Garrett. GT/VNT15-25 Type Turbos. Version 7.0 Garrett GT/VNT15-25 Type Turbos 1 st Generation Common Service Parts Qty in Turbo 1102-015-751 1102-015-752 1102-015-753 1102-015-754 1102-015-755 1102-015-756 1102-015-758 1102-015-759 1102-015-760 1102-015-761

More information

The Problem Solving of Exhaust Frame Air Cooling System Pressure Low in GE Frame 9 Gas Turbine

The Problem Solving of Exhaust Frame Air Cooling System Pressure Low in GE Frame 9 Gas Turbine The Problem Solving of Exhaust Frame Air Cooling System Pressure Low in GE Frame 9 Gas Turbine Author: Nattapon Pinitchan, Kanyarat Tankong, EGAT (Bangpakong Power Plant), Thailand 1 of 10 ABSTRACT EGAT's

More information

Drive shaft, servicing

Drive shaft, servicing Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,

More information

Pipe Cutting and Beveling Machines LCSF. Externally mounted portable pipe cutting and beveling system.

Pipe Cutting and Beveling Machines LCSF. Externally mounted portable pipe cutting and beveling system. Externally mounted portable pipe cutting and beveling system. Optional "Bridge Slide" for heavy wall pipe. Bevel, compound bevel and J prep. All "Low Clearance Split Frames" are designed for portability

More information

Evaluation and Successful Modification of Impeller Using Forced Response Analysis

Evaluation and Successful Modification of Impeller Using Forced Response Analysis Turbomachinery Symposium 2008 Case study Evaluation and Successful Modification of Impeller Using Forced Response Analysis Bhabesh Thakur Hui Kuang Robert Huffman Murari Singh GE Oil & Gas, Bethlehem,

More information

Forces on Large Steam Turbine Blades

Forces on Large Steam Turbine Blades Forces on Large Steam Turbine Blades RWE npower Mechanical and Electrical Engineering Power Industry INTRODUCTION RWE npower is a leading integrated UK energy company and is part of the RWE Group, one

More information

3D printing at Siemens Power Service

3D printing at Siemens Power Service Vladimir Navrotsky, Ph.D., CTO, PS DGC 3D printing at Siemens Power Service siemens.com Additive Manufacturing / 3 D Printing / SLM * enabling a revolution in spare parts repair & manufacturing Additive

More information

MAINTENANCE INFORMATION SYSTEMS

MAINTENANCE INFORMATION SYSTEMS MAINTENANCE INFORMATION SYSTEMS A maintenance information system is a necessary part of a good maintenance program. Such a system makes the maintenance program more effective and reduces its cost in the

More information

MэKEMMEL MUTFAKLAR YARATIR CREATING THE PERFECT KITCHEN. TэV-CB ISO 9000 QUALITY MANAGEMENT SYSTEM TURKEY PRODUCT CETIFICATE RUSSIA PRODUCT

MэKEMMEL MUTFAKLAR YARATIR CREATING THE PERFECT KITCHEN. TэV-CB ISO 9000 QUALITY MANAGEMENT SYSTEM TURKEY PRODUCT CETIFICATE RUSSIA PRODUCT CREATING THE PERFECT KITCHEN MэKEMMEL MUTFAKLAR YARATIR TURKEY CETIFICATE RUSSIA ELECTRICAL APPLIANCES GAS APPLIANCES USA GAS AND ELECTRICAL APPLIANCES UKRAINE ISO 9000 QUALITY MANAGEMENT SYSTEM GAS APPLIANCES

More information

Radius and Diameter of Circles (A)

Radius and Diameter of Circles (A) Radius and Diameter of Circles (A) C=40.841 ft C=57.805 mm C=15.708 ft C=33.929 cm Radius and Diameter of Circles (A) Answers C=40.841 ft C=57.805 mm 6.5 ft 9.2 mm 13.0 ft 18.4 mm C=15.708 ft C=33.929

More information

Oil and Gas Pipeline Design, Maintenance and Repair

Oil and Gas Pipeline Design, Maintenance and Repair Oil and Gas Pipeline Design, Maintenance and Repair Dr. Abdel-Alim Hashem Professor of Petroleum Engineering Mining, Petroleum & Metallurgical Eng. Dept. Faculty of Engineering Cairo University aelsayed@mail.eng.cu.edu.eg

More information

Installation Instructions

Installation Instructions Page 1 of 11 Part Number: AM369D25421-5 Part Name: OIL SEAL Eligibility: MDHI Model 369D/E/FF (two bladed), 500N, 600N GENERAL 1 General 1.1. Refer to Figures 1 through 7 for Oil Seal location and general

More information

LARGE CNC LATHE: DAEWOO TRAVEL: X-AXIS BED SWING IS 28 TRAVEL: Y-AXIS CARRIAGE IS 16 TRAVEL: Z-AXIS IS 156

LARGE CNC LATHE: DAEWOO TRAVEL: X-AXIS BED SWING IS 28 TRAVEL: Y-AXIS CARRIAGE IS 16 TRAVEL: Z-AXIS IS 156 LARGE CNC LATHE: DAEWOO TRAVEL: X-AXIS BED SWING IS 28 TRAVEL: Y-AXIS CARRIAGE IS 16 TRAVEL: Z-AXIS IS 156 LARGE HORIZONTAL BORING MILL: SCHARMANN CAPABLE OF BORING AND MILLING A VARIETY OF PARTS TO YOUR

More information

ENGINEERING, MAINTENANCE AND MANUFACTURE OF SPECIAL COMPONENTS

ENGINEERING, MAINTENANCE AND MANUFACTURE OF SPECIAL COMPONENTS RWE Power ENGINEERING, MAINTENANCE AND MANUFACTURE OF SPECIAL COMPONENTS The RWE Maintenance and Engineering Center RWE Power AG Maintenance and Engineering Center Frechener Straße 12 50226 Frechen CCS_0114

More information

Product Features. Product Description. Bulletin 034 Rev. F June Model G5 Series Sprinkler Cover Plates

Product Features. Product Description. Bulletin 034 Rev. F June Model G5 Series Sprinkler Cover Plates Bulletin 034 Rev. F Model G5 Series Sprinklers Available with Solid, Perforated, or Gasket Standard Coverage, Concealed Pendent K2.8, 4.2, 5.6, & 8.0 (40, 60, 80, & 115 metric) Product Features Model G5

More information

Company Profile. New and overhauled Power Plants for sale

Company Profile. New and overhauled Power Plants for sale 1 Company Profile New and overhauled Power Plants for sale - Combined Cycle - Gas & Steam Turbines - Gas & Diesel Engines - Wind Turbines & Green Energy - Coal fired Power & Waste to Energy - Biomass &

More information

R44 SERVICE BULLETIN SB-89 (supersedes R44 Safety Alert dated 23 February 2015)

R44 SERVICE BULLETIN SB-89 (supersedes R44 Safety Alert dated 23 February 2015) R44 SERVICE BULLETIN SB-89 (supersedes R44 Safety Alert dated 23 February 2015) Page 1 of 6 DATE: 30 March 2015 TO: R44 & R44 II Owners, Operators, and Maintenance Personnel SUBJECT: Main Rotor Blade Modification

More information

IP Probes: Test Probe A

IP Probes: Test Probe A IP Probes: Test Probe A 1. (Auto-A ) Test sphere probe with handle IEC60529,IEC61032,IEC60335,IEC61029,IEC607 45,IEC60065,IEC60950. This probe is intended to verify protection of persons against access

More information

understand the fundamental of the gauges and their classifications, and

understand the fundamental of the gauges and their classifications, and UNIT 4 LIMIT GAUGING Structure 4.1 Introduction Objectives 4.2 Gauges and their Classifications 4.2.1 Standard Gauges 4.2.2 Limit Gauges 4.3 Working Gauges, Inspection Gauges and Reference Gauges 4.4 Gauges

More information

DMLS / SLM Metal 3D Printing.

DMLS / SLM Metal 3D Printing. DMLS / SLM Metal 3D Printing. An introductory design guide for our 3d printing in metal service. v2.2-8th July 2015 Pricing considerations. Part Volume. One of the biggest factors in the price for DMLS

More information

siemens.com/energy Houston Service Center An integral part of the Siemens Global Service Network

siemens.com/energy Houston Service Center An integral part of the Siemens Global Service Network siemens.com/energy Houston Service Center An integral part of the Siemens Global Service Network Our network of world-class repair facilities offers the most advanced equipment and OEM engineering talent

More information

BRIDGE FIELD PAINTING, REPAINTING, 412 AND PAINT RESIDUE CONTAINMENT. A. Field Painting, Bridge Repainting and Residue Containment:

BRIDGE FIELD PAINTING, REPAINTING, 412 AND PAINT RESIDUE CONTAINMENT. A. Field Painting, Bridge Repainting and Residue Containment: 412.1 DESCRIPTION BRIDGE FIELD PAINTING, REPAINTING, 412 This specification contains the requirements for the removal, containment, and disposal of existing paint on steel surfaces, preparing the steel

More information

Sulzer Turbo Services

Sulzer Turbo Services Sulzer Turbo Services Start-Up Services Sulzer Turbo Services Worldwide repair and testing facilities Continuous Training Field Service Engineering LTSA s Our largest facility, located in La Porte, TX

More information

DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4

DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4 DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD

More information

Design of small electric generator by free CAD and analysis software

Design of small electric generator by free CAD and analysis software 3C14 small electric generator by free CAD and analysis software Kunihiko TACHIBANA *1, Koichi OKA *1 (Mem.) This paper presents a procedure of design of small electric generator by free CAD and analysis

More information

Atling proudly presents the next generation self centering steady rests ATLING. Ockelbo Sweden. AX Steady Rests

Atling proudly presents the next generation self centering steady rests ATLING. Ockelbo Sweden. AX Steady Rests Atling proudly presents the next generation self centering steady rests ATLING Ockelbo Sweden AX Steady Rests 1 The New AX Steady Rest The Atling AX series is the result of several years of development

More information

WIND ENERGY - BASIC PRINCIPLES

WIND ENERGY - BASIC PRINCIPLES Module.1- WIND ENERGY - BASIC PRINCIPLES Gerhard J. Gerdes Workshop on Renewable Energies November 14-5, 005 Nadi, Republic of the Fiji Islands Contents calculate the power in the wind power coefficient

More information

Jobson THE RIGHT CONTACT

Jobson THE RIGHT CONTACT THE RIGHT CONTACT Jobson Italia srl was set up in 1990. The following services are rendered 365 days a year, 24 hours a day: Stocking and trading of spare parts: Main Engines, auxiliary engines, pumps,

More information

CORRTECH ENSOL GAS TURBINE SERVICES (P) LTD

CORRTECH ENSOL GAS TURBINE SERVICES (P) LTD CORRTECH ENSOL GAS TURBINE SERVICES (P) LTD CORRTECH ENSOL GAS-TURBINE SERVICES PVT LTD 14/3, Havells Chowk, Mathura Road,Faridabad Haryana-121003 Phone:0129-4252200-19 1 P a g e Component Manufacture

More information

Rear brake - drum brake, servicing

Rear brake - drum brake, servicing Page 1 / 9 46-2 Rear brake - drum brake, servicing Rear brake, removing and installing Grease cap Removing and installing 42-3, Pressing off grease cap Pin Replace Castle nut Hex nut Page 2 / 9 Adjusting

More information

Industrial Metrology and Engineering Applications in the Wind Turbine Industry

Industrial Metrology and Engineering Applications in the Wind Turbine Industry Industrial Metrology and Engineering Applications in the Wind Turbine Industry 1. Company Introduction M-7 Technologies is a privately owned, ISO 9001 certified company offering engineered solutions for

More information

127 PCS. Art. NO. 712701 Art. NO. 712702 Art. NO. 712703. www.sonic-equipment.com

127 PCS. Art. NO. 712701 Art. NO. 712702 Art. NO. 712703. www.sonic-equipment.com 7 PCS Art. NO. 770 Art. NO. 770 Art. NO. 770 8 drawers with ball bearing slides drawers completely filled with 7-pcs tools drawer blocking system, as protection against tipping over abs topblade can holder

More information

www.prall-tec.de Processing Technology Impact Crusher Hammer Mills Repairs Spare Parts Second Hand Machines Service

www.prall-tec.de Processing Technology Impact Crusher Hammer Mills Repairs Spare Parts Second Hand Machines Service Seite 1 von 13 Processing Technology www.prall-tec.de Seite 2 von 13 Seite 3 von 13 In all sizes, in every performance level and suitable for all materials Natural Stone Seite 4 von 13 Recycling Natural

More information

MODEL INSTALLATION INSTRUCTIONS

MODEL INSTALLATION INSTRUCTIONS WWW.BURCAM.COM 2190 Boul. Dagenais West TEL: 514.337.4415 LAVAL (QUEBEC) FAX: 514.337.4029 CANADA H7L 5X9 info@burcam.com Your pump has been carefully packaged at the factory to prevent damage during shipping.

More information

Integral Blade Stabilizers

Integral Blade Stabilizers Integral Blade Stabilizers (Alloy Steel) SB Darron Alloy Stabilizers are manufactured from AISI 4145 H Modified Steel, fully heat treated to 285-341 Brinell hardness and 40 ft. lbs. min. izod impact strength.

More information

Portable Boring Bars

Portable Boring Bars Portable Boring Bars Who We Are One Company, Total Support, Complete Solutions Over many years, Hydratight has provided world-class bolted joint solutions and continues to set international standards in

More information

Altman Easy Latch Kit for a Ford Coupe and Tudor Sedan

Altman Easy Latch Kit for a Ford Coupe and Tudor Sedan Altman Easy Latch Kit for a 1941-48 Ford Coupe and Tudor Sedan PLEASE READ THIS NOTICE BEFORE BEGINNING ANY PHASE OF INSTALLATION!!!! This kit is designed to be installed by someone with a fair amount

More information

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900

More information

Reasons for reissue are provided in Section 6, REVISION SUMMARY.

Reasons for reissue are provided in Section 6, REVISION SUMMARY. Reasons for reissue are provided in Section 6, REVISION SUMMARY. The FRONT OF TOOL has the AMP marking on the link. The BACK OF TOOL (Wire Side), into which the wire is inserted, has the wire size marked

More information

RPMV & RPMX Rotor impact mill. The ball shaper for the recycling industry

RPMV & RPMX Rotor impact mill. The ball shaper for the recycling industry RPMV & RPMX Rotor impact mill The ball shaper for the recycling industry Office building at BHS-Sonthofen The company BHS-Sonthofen is an owner-operated group of companies in the machinery and plant engineering

More information

Evaluation of Oxyfuel Gas Cutting Gases

Evaluation of Oxyfuel Gas Cutting Gases Evaluation of Oxyfuel Gas Cutting Gases July 14, 2014 EWI Project No. 55272CSP Submitted to: Magnegas Tarpon Springs, Florida Report Project No. 55272CSP on Evaluation of Oxyfuel Gas Cutting Gases to Magnegas

More information

Recent outbreaks of pinhole leaks nationally are a significant issue. Figure 1.1 shows the

Recent outbreaks of pinhole leaks nationally are a significant issue. Figure 1.1 shows the CHAPTER 1 - INTRODUCTION 1. 1 Motivation Recent outbreaks of pinhole leaks nationally are a significant issue. Figure 1.1 shows the national distribution of pinhole leaks based on the data gathered by

More information

Organisational Kitchen Fittings Kitchen Cabinet Fittings

Organisational Kitchen Fittings Kitchen Cabinet Fittings Pull-out wire storage basket Finish: Chrome plated Load capacity: 30 kg Installation depth: 400 mm Version: Runners and baskets separated, designed for wardrobe interiors without doors Type of pull out:

More information

Industrial Vibration Analysis for Predictive Maintenance and Improved Machine Reliability

Industrial Vibration Analysis for Predictive Maintenance and Improved Machine Reliability Connection Technology Center, Inc. 590 Fishers Station Drive Victor, New York 14564 Toll Free: (800) 999-5290 Phone: (585) 924-5900 Fax: (585) 924-4680 Industrial Vibration Analysis for Predictive Maintenance

More information

Direct Gear Design for Optimal Gear Performance

Direct Gear Design for Optimal Gear Performance Direct Gear Design for Optimal Gear Performance Alex Kapelevich (AKGears, LLC), Thomas McNamara (Thermotech Company) The paper presents the Direct Gear Design an alternative method of analysis and design

More information

Provided by Productivity Quality Inc s Metrology Toolbox

Provided by Productivity Quality Inc s Metrology Toolbox Plug gaging of holes by the GO-NOGO method By Van Keuren Introduction Introduction The American National Standards Institute defines a gage as "a device for determining whether or not one or more dimensions

More information

Chrome Finishing For 3d Powder Prints

Chrome Finishing For 3d Powder Prints Chrome Finishing For 3d Powder Prints Powder Printing is definitely a very good technology for producing complex parts, but it can only generate the shape and that is not all about the appearance. Post

More information

INSTRUCTIONS FOR PROPER INSTALLATION OF ROSS FORGED ALUMINUM AUTOMOTIVE PISTONS

INSTRUCTIONS FOR PROPER INSTALLATION OF ROSS FORGED ALUMINUM AUTOMOTIVE PISTONS INSTRUCTIONS FOR PROPER INSTALLATION OF ROSS FORGED ALUMINUM AUTOMOTIVE PISTONS IMPORTANT: Before balancing these pistons, be sure they are as you ordered. Used or altered parts cannot be returned for

More information

Practice Problems on Boundary Layers. Answer(s): D = 107 N D = 152 N. C. Wassgren, Purdue University Page 1 of 17 Last Updated: 2010 Nov 22

Practice Problems on Boundary Layers. Answer(s): D = 107 N D = 152 N. C. Wassgren, Purdue University Page 1 of 17 Last Updated: 2010 Nov 22 BL_01 A thin flat plate 55 by 110 cm is immersed in a 6 m/s stream of SAE 10 oil at 20 C. Compute the total skin friction drag if the stream is parallel to (a) the long side and (b) the short side. D =

More information

CONSIDERATIONS IN THE USE OF PULSED WATER JET TECHNIQUES FOR THE REMOVAL OF HVOF COATINGS

CONSIDERATIONS IN THE USE OF PULSED WATER JET TECHNIQUES FOR THE REMOVAL OF HVOF COATINGS 2007 American WJTA Conference and Expo August 19-21, 2007 Houston, Texas Paper CONSIDERATIONS IN THE USE OF PULSED WATER JET TECHNIQUES FOR THE REMOVAL OF HVOF COATINGS Andrew Tieu, Wenzhuo Yan and Mohan

More information

SLLS Linear Ceiling Diffuser

SLLS Linear Ceiling Diffuser SLLS Linear Ceiling Diffuser ASLI SLLS series is a type of diffuser combine a high air change rate capacity with maximum flexibility in air pattern and volume control. It offers unobtrusive good looks

More information

Our Comprehensive Solutions Your Air Ability THE LEADING ENGINE MRO

Our Comprehensive Solutions Your Air Ability THE LEADING ENGINE MRO Our Comprehensive Solutions Your Air Ability THE LEADING ENGINE MRO BATS A FULL SERVICE PROVIDER Belgian Advanced Technology Systems (BATS) is a world renowned aerospace corporation with hundreds of innovative

More information

ERBIL PLOYTECHNIC UNIVERSITY ERBIL TECHNICAL ENGINEERING COLLEGE. Fluid Mechanics. Lecture 3 - Solved Examples (7 examples) - Home works

ERBIL PLOYTECHNIC UNIVERSITY ERBIL TECHNICAL ENGINEERING COLLEGE. Fluid Mechanics. Lecture 3 - Solved Examples (7 examples) - Home works ERBIL PLOYTECHNIC UNIVERSITY ERBIL TECHNICAL ENGINEERING COLLEGE Fluid Mechanics Lecture 3 - Solved Examples (7 examples) - Home works By Dr. Fahid Abbas Tofiq 1 Example 1: A plate 0.025 mm distant from

More information

Customised solutions: SCREW CONVEYORS AND EARTH AUGERS

Customised solutions: SCREW CONVEYORS AND EARTH AUGERS Customised solutions: SCREW CONVEYORS AND EARTH AUGERS SCREW FLIGHTS SCREW CONVEYORS EARTH AUGERS ANDERS PEDERSEN MASKIN- & SPECIALFABRIK OUR VORES SCREW SNEGLE CONVEYORS BRUGES TIL ARE USED FOR TRANSPORT

More information

Rear brake on vehicles with all wheel drive

Rear brake on vehicles with all wheel drive Page 1 of 17 46-29 Rear brake on vehicles with all wheel drive Exploded view 1 - Hex socket head bolt - 65 Nm 2 - Brake carrier With guide pins and protective cap Supplied as replacement part assembled

More information

Aluminium mold repair 2003 ALCAN INC.

Aluminium mold repair 2003 ALCAN INC. Aluminium mold repair 2003 ALCAN INC. Overview Best repair technologies according to defect size and location GTAW technologies Principle On aluminium products Welding procedure Choice of filler wires

More information

Breitenbach TRADITION

Breitenbach TRADITION Product range Breitenbach Precision from TRADITION Since the foundation of our company in 1866 we have developed into a modern, globally operating company offering a wide range of products and services.

More information

in-service inspections www.sgs.com

in-service inspections www.sgs.com in-service inspections www.sgs.com Minimising down -time for wind turbines One of the major concerns in investing in wind farm projects is related to turbine availability, which represents the risk of

More information

HOME OFFICE SPECIFICATION FOR SEAMLESS ALLOY STEEL CYLINDERS FOR THE CONVEYANCE OF COMPRESSED GASES HOT

HOME OFFICE SPECIFICATION FOR SEAMLESS ALLOY STEEL CYLINDERS FOR THE CONVEYANCE OF COMPRESSED GASES HOT HOME OFFICE SPECIFICATION FOR SEAMLESS ALLOY STEEL CYLINDERS FOR THE CONVEYANCE OF COMPRESSED GASES HOT 1 Cylinders manufactured to these specifications shall be manufactured by a cylinder manufacturer

More information

MBG GRATINGS. MBG Metal Bar Grating WELDING STANDARDS FOR FABRICATION OF STEEL, STAINLESS STEEL AND ALUMINUM METAL BAR GRATING -09

MBG GRATINGS. MBG Metal Bar Grating WELDING STANDARDS FOR FABRICATION OF STEEL, STAINLESS STEEL AND ALUMINUM METAL BAR GRATING -09 METAL BAR GRATING AMERICAN NATIONAL STANDARD ANSI/NAAMM STANDARD MBG 533-09 GRATINGS 5 ANSI/NAAMM MBG 533-09 June 15, 2009 WELDING STANDARDS FOR FABRICATION OF STEEL, STAINLESS STEEL AND ALUMINUM BAR GRATING

More information

SECTION 1 GENERAL REQUIREMENTS

SECTION 1 GENERAL REQUIREMENTS Page 1 of 6 SECTION 1 GENERAL REQUIREMENTS 1. SCOPE OF WORK: The work to be performed under the provisions of these documents and the contract based thereon includes furnishing all labor, equipment, materials,

More information

MANUFACTURER HARRIS MODEL 2 ESAB MODEL 3 MESSER MODEL 4

MANUFACTURER HARRIS MODEL 2 ESAB MODEL 3 MESSER MODEL 4 v. 240314 REPLACEMENT PARTS SUITABLE FOR OXY FUEL CUTTING MANUFACTURER PAGE REPLACEMENT PARTS SUITABLE FOR HARRIS MODEL 2 ESAB MODEL 3 MESSER MODEL 4 HARRIS is the registered trademark of Lincoln Global

More information

Wind Energy Generator

Wind Energy Generator Wind Energy Generator Parts Manual Manual de Partes English Español SPP-205 Model 2002 by ELECFURE Corporation Table of Contents I. List of Parts II. Parts Location III. Additional Information 2 List of

More information

SAFE A HEAD. Structural analysis and Finite Element simulation of an innovative ski helmet. Prof. Petrone Nicola Eng.

SAFE A HEAD. Structural analysis and Finite Element simulation of an innovative ski helmet. Prof. Petrone Nicola Eng. SAFE A HEAD Structural analysis and Finite Element simulation of an innovative ski helmet Prof. Petrone Nicola Eng. Cherubina Enrico Goal Development of an innovative ski helmet on the basis of analyses

More information

Improved Life for Dynamic Seals in Wind Turbine Applications

Improved Life for Dynamic Seals in Wind Turbine Applications Improved Life for Dynamic Seals in Wind Turbine Applications By Elizabeth Chitren - Product Engineer, Klozure Dynamic Seals, Palmyra, NY Jim Drago, P.E. - Manager, Engineering, Garlock Sealing Technologies,

More information

MTX-D, Water Temperature/Volt Gauge

MTX-D, Water Temperature/Volt Gauge MTX-D, Water Temperature/Volt Gauge 1 Mounting and Sensor Installation... 3 1.1 Mounting the Gauge... 3 1.2 Water Temp Sensor... 3 2 Wiring... 3 2.1 Main Gauge Wiring... 3 2.2 Water Temp Sensor Wiring...

More information

American Petroleum Institute Purchasing Guidelines Purchase API Spec 5CT online at www.api.org/publications

American Petroleum Institute Purchasing Guidelines Purchase API Spec 5CT online at www.api.org/publications API Specification 5CT ISO 11960:2011 Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells 9th Edition, June 2011 Table of Contents 1.0 Product 1.1 Products 1.2 Casing

More information

WORLD CLASS SUPPLIER CLOSE TO ISTANBUL

WORLD CLASS SUPPLIER CLOSE TO ISTANBUL WORLD CLASS SUPPLIER CLOSE TO ISTANBUL When you type Turkey on Internet you arrive quickly to websites that emphasize the beauty of the country and all the holiday possibilities. With its slogan Turkey

More information

Implementation of Emergency Repair Work for Steam Turbine at Himeji No. 2 Power Station, Kansai Electric Power Co., Inc.

Implementation of Emergency Repair Work for Steam Turbine at Himeji No. 2 Power Station, Kansai Electric Power Co., Inc. June 10, 2015 The Kansai Electric Power Co., Inc. Implementation of Emergency Repair Work for Steam Turbine at Himeji No. 2 Power Station, Kansai Electric Power Co., Inc. The Kansai Electric Power Co.,

More information

Quotation for Roll forming Machine line

Quotation for Roll forming Machine line Quotation for Roll forming line Date : 2014/3/8 No. 20140308 HS:84552210 1. Price List (USD) No. Item Unit price Qty Total price 1 Roll forming machine 13,500 1 13,500 2 Manu decoiler free 1 free 3 Total

More information

DIVISION: 22 00 00 PLUMBING SECTION: 22 11 16 DOMESTIC WATER PIPING REPORT HOLDER: CURAFLO IP LLC 4035 E. OASIS STREET MESA, AZ 85215

DIVISION: 22 00 00 PLUMBING SECTION: 22 11 16 DOMESTIC WATER PIPING REPORT HOLDER: CURAFLO IP LLC 4035 E. OASIS STREET MESA, AZ 85215 0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted PMG 1057 Valid: 02/15 to 02/16 DIVISION: 22 00 00 PLUMBING SECTION: 22 11 16 DOMESTIC WATER PIPING

More information

VARIABLE VANE PUMPS V3

VARIABLE VANE PUMPS V3 VARIABLE VANE PUMPS V3 (series 30 and 40) Nominal sizes 12; 25; 40; 63 up to p n 100 bar V g 8.5; 19; 32; 47 cm 3 /rev KE 1015 11/02 replaces 07/97 easy commissioning due to automatic bleed facility low

More information

Part No. Quantity Description Diameter Length

Part No. Quantity Description Diameter Length PUSHRODS SMALL BLOCK CHEVROLET SWEDGED END PUSHRODS.080 WALL 1010 STEEL 3 Heat treated and black oxide finish 3 For use in hydraulic lifter applications with less than 400 lbs. open spring pressure and

More information

Fleet Services. Carl Gillyon. Fleet Services Manager. Fleet Management Vehicle Maintenance

Fleet Services. Carl Gillyon. Fleet Services Manager. Fleet Management Vehicle Maintenance Fleet Services Carl Gillyon Fleet Services Manager Fleet Management Vehicle Maintenance (FMU) (VMU) 1 East Riding of Yorkshire 930 Square Miles 350,000 Population 2 Fleet Services Setting the scene 650+

More information

System. Stability. Security. Integrity. 150 Helical Anchor

System. Stability. Security. Integrity. 150 Helical Anchor Model 150 HELICAL ANCHOR System PN #MBHAT Stability. Security. Integrity. 150 Helical Anchor System About Foundation Supportworks is a network of the most experienced and knowledgeable foundation repair

More information

Rules for the Installation, Inspection & Testing of Air Reservoirs (Other than on Locomotives) December 1994 (TC O-0-10)

Rules for the Installation, Inspection & Testing of Air Reservoirs (Other than on Locomotives) December 1994 (TC O-0-10) Rules for the Installation, Inspection & Testing of Air Reservoirs (Other than on Locomotives) December 1994 (TC O-0-10) PART I - GENERAL 1. Short Title 2. Scope 3. Definitions 4. General 5. Reservoir

More information

79 th Annual Montana 4H Congress. WIND ENERGY Workshop

79 th Annual Montana 4H Congress. WIND ENERGY Workshop 79 th Annual Montana 4H Congress WIND ENERGY Workshop Wednesday Schedule 1:30-1:45 1:45 2:05 2:05 2:45 2:45 4:00 4:00 4:30 Introduction and overview Presentation: Wind Energy Tour of MSU Facilities Wind

More information

Characterization of High Temp Thermal Sprays for Engine Applications. Nick Jacobs UDRI Presented at HCAT Kennedy Space Center November 19, 2003

Characterization of High Temp Thermal Sprays for Engine Applications. Nick Jacobs UDRI Presented at HCAT Kennedy Space Center November 19, 2003 Characterization of High Temp Thermal Sprays for Engine Applications Nick Jacobs UDRI Presented at HCAT Kennedy Space Center November 19, 2003 1 Management Structure AFRL Program initiated by AFRL/MLSC

More information

RESIDUAL STRESSES AND THEIR EFFECTS ON FATIGUE RESISTANCE

RESIDUAL STRESSES AND THEIR EFFECTS ON FATIGUE RESISTANCE RESIDUAL STRESSES AND THEIR EFFECTS ON FATIGUE RESISTANCE Ali Fatemi-University of Toledo All Rights Reserved Chapter 8 Residual Stresses & Their Effects 1 RESIDUAL STRESSES AND THEIR EFFECTS ON FATIGUE

More information

SAMPLE CHAPTERS UNESCO EOLSS

SAMPLE CHAPTERS UNESCO EOLSS STEAM TURBINE OPERATIONAL ASPECTS R.A. Chaplin Department of Chemical Engineering, University of New Brunswick, Canada Keywords: Steam Turbines, Operation, Supersaturation, Moisture, Back Pressure, Governing

More information

DURAFIX WELDING INSTRUCTIONS

DURAFIX WELDING INSTRUCTIONS New Zealand Aluminium Soldering Rods Repairs Aluminium & Zinc Based Metals Product Sales & Demonstrations Mobile Aluminium Welding LR & TJ Jordan PO Box 512 Kaitaia 0441 DURAFIX WELDING INSTRUCTIONS New

More information

ANCHOR BOLTS FOR NUCLEAR POWER PLANT APPLICATIONS

ANCHOR BOLTS FOR NUCLEAR POWER PLANT APPLICATIONS ANCHOR BOLTS FOR NUCLEAR POWER PLANT APPLICATIONS EXPERIENCE FROM DESIGN AND CONSTRUCTION OF OLKILUOTO UNITS 2015-11-03 Kukkola Timo 2 OL1 AND OL2 CROSS-SECTION 3 OL1 AND OL2 OL1 and OL2 continuous improvement

More information

PRT Tubing Installation (ZT )

PRT Tubing Installation (ZT ) PRT Tubing Installation (ZT99-98-003) Background PRT tubing is a wrap-a-round, heat shrinkable tubing that provides the same high performance characteristics of solid heat shrinkable tubing with the installation

More information

NORSOK Compact Flange Installation and Assembly Procedure

NORSOK Compact Flange Installation and Assembly Procedure NORSOK Compact Flange Installation and Assembly Procedure Hytorc Norway www.hytorc.no P.Nødland. Page 2 INTRODUCTION Scope The following main operations are covered in this section: Assembly/disassembly

More information

Fixed Asset Policy and Procedures

Fixed Asset Policy and Procedures Fixed Asset Policy and Procedures Adopted: xxx, 2014 Resolution: 2014-x 204 W Montgomery Street, Mount Vernon, WA 98273 PURPOSE FIXED ASSET POLICY AND PROCEDURES The following policy and procedures document

More information

TECTUS Concealed Hinges

TECTUS Concealed Hinges Concealed Hinges index TE 240 3d up to 40 kg (88 lbs) 6 TE 340 3d up to 80 kg (176 lbs) 7 TE 525 3d up to 120 kg (264 lbs) 8 TE 526 3d up to 120 kg (264 lbs) 9 TE 527 3d up to 120 kg (264 lbs) 10 TE 540

More information

: PRECISION GRINDING PRACTICE (Surface grinding, Cylindrical grinding and Centreless grinding)

: PRECISION GRINDING PRACTICE (Surface grinding, Cylindrical grinding and Centreless grinding) : PRECISION GRINDING PRACTICE (Surface grinding, Cylindrical grinding and Centreless grinding) COURSE S.NO. : 9.01 COURSE CONTENT Principles of grinding process, grinding accuracies and finish and grinding

More information

EE Bucket datasheet Height 1580 mm. Width 2000 mm. Depth 1690 mm

EE Bucket datasheet Height 1580 mm. Width 2000 mm. Depth 1690 mm EE 3160 1580 mm 2000 mm Volume ISO (m³) 2,1 Volume SAE(m³) 2,4 Screening area (m²) 1,4 Mass of the bucket (kg) 2300 weight for excavator (tons) 25 weight for wheel loader (tons) 8 1690 mm Uses 60 mm axels

More information

Wet Stator Units for Oil and Gas Upgrade and support services

Wet Stator Units for Oil and Gas Upgrade and support services Wet Stator Units for Oil and Gas Upgrade and support services Electro-submersible Pump Maintenance Sulzer has the in-house capability to provide specialist service support to the upstream oil and gas industry

More information

MANLEY VALVE TRAIN COMPONENTS FOR HARLEY-DA -DAVIDSON MOTORCYCLES

MANLEY VALVE TRAIN COMPONENTS FOR HARLEY-DA -DAVIDSON MOTORCYCLES MANLEY VALVE TRAIN COMPONENTS FOR HARLEY-DA -DAVIDSON MOTORCYCLES 1 VALVE TRAIN COMPONENTS V MANLEY PERFORMANCE PRODUCTS, INC. PHONE: 732-905-3366 FAX: 732-905-3010 The standard of the industry since their

More information

Precision components from start to finish. Excellence. in performance-critical machining & fabrications

Precision components from start to finish. Excellence. in performance-critical machining & fabrications Precision components from start to finish Excellence in performance-critical machining & fabrications Leading precision machining technology... Fully integrated solutions Facilities and capabilities The

More information