Motorola MIP 5000 VoIP Radio Console. General Information

Transcription

1 Page 1 of 15 Motorola MIP 5000 VoIP Radio Console Ship Card General Information *MIP5000 Release 4.2 Now Shipping* MIP 5000 Release 4.2 Features Support for XPR 5550 MOTOTRBO Mobile 48 Channel Support Micosoft Windows Bit Multi-Touch Monitor Support Dual Channel IRR Support The MIP 5000 VoIP Radio Console is designed to provide customers an affordable solution to transmit dispatch quality voice over their existing Multicast enabled Ethernet network. The MIP 5000 radio console connects up to 100 users with flexible licensing that is available with 1, 4, 8, 12, 24, and 48 channel software options. In addition, up to 128 radio resources can be connected to the network and configured in the Console System Database Manager (CSDM). These configuration files can be saved on each operator position to allow the dispatcher to access & control different combinations of radio resources (up to 48 at a time). MIP 5000 consists of Gateways which connect the radios to the Network and Operator Position components including: MIP 5000 application software, Personal Computer (PC), and Audio accessories. Gateways There are 4 types of gateways available in a MIP 5000 system to interface to radios: Local, Tone, Digital, and MOTOTRBO. Gateways have a one to one relationship to radios. One gateway is required for each radio controlled. Local Gateway L3482 controls radios, typically Mobiles in a Tray, via Microphone and Speaker connection and will support up to 16 frequency select (depending on radio capability). Radio interface cables: Prewired cable for CDM Family DDN6338 Prewired cable for MCS2000 DDN6699

2 Page 2 of 15 Generic radio cable for use with XTL family DDN6340 (Requires field install of XTL accessory connector) Map universal cable for use with MOTOTRBO/XPR family including Connect Plus PMKN4018 (Requires field install of DB25 for local gateway) Tone Gateway L3483 controls base stations or repeaters with tone control signaling which will support up to 16 frequency select (depending on radio capability) via 600 Ohm lease lines. In addition, the tone gateway will also support E&M signaling. DIU With a tone gateway connected to the 4 wire interface on a DIU, the MIP 5000 can talk/listen, change frequency and, select coded/clear. However, MIP 5000 does not support the ACIM link functionality of the DIU. Digital Gateway L3484 acts as a virtual control head for specific Motorola radios or Consolettes via the SB9600 protocol. MIP 5000 will display the Alias ID if the individual Subscriber is configured to send it. MIP 5000 will provide the dispatcher access to the same number of frequencies the radio is capable of. Mobiles supported are: APX 7500 Mobile in a tray (05 Control Head, Remote Mount) MCS2000 Model III Spectra/Spectra Plus Consolette W9 ASTRO XTL5000 Consolette W9 CDM1550 LS/LS+ - (Requires Remote Kit (RLN4802) and Remote Cable Kit (RKN4077)). MIP 5000 Release R R R APX 7500 Firmware Version R R R MOTOTRBO Gateway L3598 acts as a virtual control head for the MOTOTRBO XPR 4550 and XPR 5550 control station. MIP 5000 will display the Alias ID when in analog or TRBO digital mode. MIP 5000 will provide the dispatcher access to the same number of frequencies the radio is capable of. MOTOTRBO system types supported are: Conventional IP Site Connect Capacity Plus Linked Capacity Plus Connect Plus - Requires Connect Plus System Release 1.4A Note: Below is a compatibility chart between the MIP 5000 and the MOTOTRBO Control station connected to the MOTOTRBO Gateway. These are the tested combinations between the radio and the MIP 5000, any other combinations may cause unexpected functionality. MIP 5000 Release XPR 4550 Firmware Version XPR 5550 Firmware Version R x N/A R x N/A R x N/A R x N/A R x N/A R x R Network It is highly recommended that customers intending to use MIP 5000 in Public Safety situations use a dedicated network for dispatching. For non public safety situations, a MIP 5000 can be placed on an existing customer network. Network

3 Page 3 of 15 must support multicast addressing and be QoS enabled. For complete network requirements, see Specification Sheet on MOL or WIKI. MIP 5000 Application Software The Channel License configurations available are: 1, 4, 8, 12, 24, or 48. Individual license per operator position is required. Site license is not available. MIP 5000 license activation is accomplished using a Hardware USB Hasp Key at each position. Each USB Hardware Hasp Key is configured for the number of channels purchased. If the USB is removed after activation, the software will continue to function for 10 days with a visible countdown reminder to allow time for key replacement. MOTOTRBO AppServer The MIP 5000 AppServer provides the tools for text messaging and private/group calls on the MOTOTRBO Conversation window. In addition to a texting server, the MOTOTRBO AppServer has a presence server to populate the MOTOTRBO Contacts Window with available MOTOTRBO radio subscribers that report their status. The MOTOTRBO AppServer does not require any additional software to purchase as it comes with every MIP 5000 Software CD. It s recommended to install the MOTOTRBO AppServer on the same PC as the MIP 5000 CSDM/TFTP Server because it needs to have 24/7 availability. Like the TFTP Server, only one AppServer is required per MIP 5000 System. In addition to installing the AppServer, a MOTOTRBO Gateway must be configured to receive MOTOTRBO data. The quantity of MOTOTORBO Gateways needed will depend on your system type. For IP Site Connect Systems, 1 MOTOTRBO Gateway is needed for every repeater and timeslot desired to be simultaneously monitored. For example, a 2 repeater site has 4 timeslots total so 4 MIP 5000 MOTOTRBO Gateways and XPR 4550 Control Stations are needed. Note: Each control station must be programmed with the same MOTOTRBO ID so data can be properly routed to the AppServer. For Capacity Plus Systems with Data Revert, 1 MOTOTRBO Gateway is needed for every voice talk group the dispatcher wants to simultaneously monitor. Also, 1 additional MOTOTRBO Gateway configured for data only is needed for every data repeater in the system. For example, if the dispatcher wants to simultaneously monitor 5 voice talk groups and the system has 3 data revert repeaters, then 8 MIP 5000 MOTOTRBO Gateways and XPR 4550 Control Stations are needed. 5 gateways will be used for voice and 3 gateways (configured for data only) will be used for ARS and Texting. Note: The additional MIP 5000 gateway set to data only mode will allow the subscribers to report their status without interrupting MIP 5000 dispatcher voice communications. The data only gateway will be a hidden resource from the dispatcher and will not count towards the total software license limit (1,4,8,12, 24, or 48). For Capacity Plus Systems without Data Revert, 1 MOTOTRBO Gateway is needed for every talk group the dispatcher wants to simultaneously monitor. For example, if the dispatcher wants to simultaneously monitor 5 talk groups, then 5 MOTOTRBO Gateways and XPR 4550 Control Stations are needed. All 5 gateways are used for both voice and data. Note: Unlike Capacity plus systems with data revert, no additional MOTOTRBO Gateways configured for data only are required to support ARS and Texting. Also, each control station must be programmed with a different MOTOTRBO ID so data can be properly routed to the AppServer. The MOTOTRBO AppServer is not supported on Connect Plus Systems, this is a limitation of the Radio. Personal Computer (PC) It is highly recommended that customers intending to use MIP 5000 in Public Safety situations purchase the TT2538 Motorola certified HP desktop computer. If not purchasing a Motorola computer, please see the Specification Sheet on MOL or WIKI for Recommended Minimum Computer Specifications. R supports Windows 7 Professional Service Pack 1 (32 or 64 Bit) or Windows Professional 8.1 (64-Bit).

4 Page 4 of 15 Audio Accessories MIP 5000 USB connected Jackbox provides the MIP 5000 operator position access to Standard (non USB) accessories. Two kinds of USB Jackboxes are available: Basic and Enhanced. Jackbox Limits 1 headset per Jackbox 1 footswitch per Jackbox 1 microphone per Operator position 2 headsets maximum per Operator position 3 Jackboxes maximum per Operator position (any combination of Basic or Enhanced) Basic USB Jackbox DDN9492 One Basic Jackbox includes 10 USB cable and will provide access for up to three accessories: one Plantronics two prong headset with Quick Disconnect, one B1914 Standard Desktop Gooseneck Microphone, and one BLN6732 Foot-switch. Only one Desktop Gooseneck Microphone (B1914) can be used per MIP 5000 position. Jackboxes are connected using USB. Basic Jackbox does not support telephone Call Director functionality. Enhanced USB Jackbox DDN9493 One Enhanced Jackbox includes 10 USB cable and provides all of the accessory capability of the Basic Jackbox plus offers an auxiliary port that supports an array of options: a) Call Director or b) External Paging Encoder or c) Analog Recorder. d) PTT, e) MDC Emergency Alarm output. See Jackbox Connector Chart below for PIN limitation guidance. Multiple Jackboxes may be required to support all desired options. Limit of 3 Jackboxes per operator position. MIP 5000 Enhanced Headset Jackbox Connector Chart PIN Recorder Call Director External Pager 1 X X 2 X X 3 X X 4 X PTT MDC Emergency Alarm Output

5 Page 5 of 15 5 X X 6 X X 7 X X X X Example #1: If Recorder and External Pager are needed at an operator position, one Enhanced Jackbox will support both since they do not share common pins on the auxiliary port. Example #2: If Call Director and External Paging are required at the operator position, two Enhanced Jackboxes are required since they use common pins #1 through #3. Speakers: Each MIP 5000 Dispatch Console operator position requires at least two desktop speakers; the select and unselect speakers. Four additional monitor speakers (unselect audio) can be connected to each MIP 5000 Operator Position by a 7.1 soundcard. The 7.1 soundcard supports up to four monitor speakers on the MIP 5000 VoIP Radio Console in addition to a select speaker and unselect speaker. Call Director: The Call Director feature on the Enhanced USB Jackbox allows one headset to be used for both telephone and radio. The telephone must be 4 wire, 600 ohm with off-hook sense. (typical phone used with E9-1-1 ) The Call Director feature is supported for both the operator and supervisor headsets. The primary headset (operator) works in the full-duplex mode and the secondary headset (supervisor), works in half-duplex mode. Call Director also supports patching with a radio channel / conversation. External Paging Encoder Input: External Paging Encoder allows access for an External Encoder device. Analog Recorder Port: Analog Recorder port provides access for analog logging recording for the operator position. PTT Whenever the Op position does a PTT, a relay closure occurs. For example this relay can be used to activate an ON- THE-AIR light. MDC Emergency Alarm Output When an inbound emergency is decoded by a local or tone gateway the MDC Emergency Alarm output relay will close at the operator position. This option can be used to activate a buzzer or light to notify the operator of an emergency condition. Recording Solutions Instant Recall Recorder (IRR) The Instant Recall Recorder (IRR) software with MIP 5000 allows users to record audio digitally on the MIP 5000 Operator position. Operator TX audio, Select and Unselect RX audio, Telephone Call Director Audio or any combination may be recorded. If PC is... Order Includes:...TT2538 MIP 5000 Certified PC DDN1612 IRR Software & License, Soundcard, and PC Speakers...Customer PC w/o Speakers DDN1612 IRR Software & License, Soundcard, and PC Speakers...Customer PC with Speakers DDN1611 & IRR Software & License, Soundcard

6 Page 6 of 15 DDN1118 Note: MIP 5000 with IRR on a laptop is not a supported configuration Analog Logging Recorder MIP 5000 can be used with legacy Analog Logging recorders to record audio at the radio and/or at the operator position (s). Analog recording at the radio is accomplished by bridging the connection between the gateway and radio. When installing an analog recording device with a MIP 5000 digital gateway a Digital Junction Box L3208 is required. When installing an analog recording device with a MIP 5000 local gateway a Local Junction Box DDN6337 is recommended. With an Analog Logging Recorder, gateways and radios must be co-located with the recorder. Analog Recording of select and/or unselect audio at the operator position is accomplished by using the auxiliary port on the enhanced jackbox (DDN9493). Ordering Other Elements 1. Jackbox, Headsets, Microphone and Footswitch should be ordered as separate line items. The CDN6673 speakers are commercial off the shelf items and can be substituted if desired. 2. For information on Instant Recall Recorder (IRR), Computer Hardware, Console Headset Accessories or Networking Equipment please refer to the following price pages. Instant Recall Recorder Computer Hardware Console Headset Accessories Networking Equipment MIP 5000 and Remote Comparator Display The MIP 5000 console can now Cohab with CTI's MCN RCD Client Server Software. This software provides real-time monitoring and control for a wide range of devices including doors, alarms, light switches, and other general purpose Auxiliary I/O applications. In addition, the MCN RCD system supports comparator/voting displays at the MIP 5000 console operator position. The MCN RCD Client Server Software is an IP based solution and can run on the same network as the MIP 5000 consoles. The MCN RCD system consists of two parts: The MCN RCD Server Software with HIB-IP Module and the specific interface module for the application. The interface module(s) can be General Purpose I/Os, Comparator module, or a combination of the two. The paired solution between the MIP 5000 console and the MCN RCD Client Server Software can support up to 192 inputs and 128 outputs. Features The MIP 5000 provides a comprehensive feature set as listed below. SIGNALING: MDC 1200 and Conventional ASTRO are supported with the following capabilities: MDC 1200 (Local and Tone Gateways) OUTBOUND MESSAGES Call Alert PTT ID Alias Emergency Alarm Radio Check Radio Disable Radio Enable Remote Monitor Manual RAC Selective Call Voice Alert INBOUND MESSAGES Call Alert* PTT ID* Emergency Alarm* Emergency Call* Radio Status* Radio Message* *Appear in Activity Log Window

7 Page 7 of 15 Conventional ASTRO (Digital Gateways, depending on the supported capability of the radio). OUTBOUND MESSAGES Call Alert PTT ID Emergency Alarm Radio Status Request Radio Check INBOUND MESSAGES Call Alert* PTT ID* Emergency Alarm* Emergency Call* Radio Status Radio Message *Appear in Activity Log Window PAGING: Both manual and pre-programmed pages are supported. Pages may be sent individually or via sequential pagelist paging. Pre-programmed lists can also be created to provide pre-programmed Group Pages. Up to 128 preprogrammed pages (single or group) can be assigned to a button that can be placed on the GUI. By default, the operator position is configured with a page history window showing recent paging activity. The paging formats listed below are supported: 5/6 Tone Custom Formats Digital Dial 1500 Hz (Rotary Pulse) Digital Dial 2805 Hz (Rotary Pulse) Quik-Call ( Motorola 2+2) Quik-Call II Tone and Voice (Motorola 1 + 1) Quik-Call II Tone Only ( Motorola 1 + 1) Single Tone Touch Code (DTMF) Knox GE Type 99 Reach PATCHING and MULTISELECT: Each operator position can support up to 11 patches: 10 with memory and 1 without memory and 11 Multiselects: 10 with memory and 1 without memory. Patch and Multiselect can each support up to 16 members. A resource cannot be a member of more than one active patch or Multiselect. An All Points Bulletin (APB) transmit feature is also available for use with the Multiselect groups. CHANNEL CONFIGURATIONS: MIP 5000 consoles support the following channel configurations for Local and Tone Gateways. All channels support analog operation with MDC 1200 signaling if so configured. Type # TX Frequencies # RX Frequencies NOTES R1 0 1 Receive Only T1R Frequency Station T2R Frequency Station T4R Frequency Station T8R Frequency Station T12R Frequency Station T14R Frequency Station T16R Frequency Station In addition to the above, SB9600 control and MOTOTRBO are supported with the number of modes and features being determined by the mobile.

8 Page 8 of 15 Manuals Soft copies of the manuals are found on the documentation CD and available on: Ordering Requirements *New required options for the MIP 5000 Gateways. You must select either TT05979AA for existing systems at Release 4.0 or earlier or select TT05980AA for new or existing systems at Release 4.1 or later.* The MIP 5000 gateways do not ship with punch blocks or cables for connecting to base stations or radios. These must be ordered separately or provided by the customer. See the Accessories section below for cables that can be used for connecting to various radios. Headset Jackbox Every MIP 5000 operator position requires either a Basic or an Enhanced headset Jackbox. The Jackbox is needed for all standard (non USB) accessories. Each position requires a minimum of 1 and can support a maximum of 3 of any combination of Jackboxes. TT05515AA is the option for the Basic Headset Jackbox and TT05522AA is the option for the Enhanced headset Jackbox. A headset(s) may be used with the MIP 5000 Console. Each headset must be connected to a MIP 5000 USB Basic or Enhanced Jackbox, A headset consist of two parts, a base and a top. A choice of two bases (RLN6098 and RLN6099) and several tops is provided. The MIP 5000 supports a maximum of two headsets per operator position. Upgrades Upgrades to R are available at no charge. Labor for upgrade installation is not reimbursable. To order contact System Support Center at , option 4 on the call tree and request that a software case be opened. Existing System Expansion All new orders for Software and Gateways will ship with the latest release software R Adding Gateways: If adding gateways onto an existing R system or earlier, gateways will automatically downgrade during the installation process to match the software release running in the system. Adding Operator Positions: If adding new operator positions to an existing R system or earlier, you will be required to upgrade the entire system (all Operator positions, CSDM and gateways) to R All operator positions and gateways in a MIP 5000 system must run the same version of software. Instant Recall Recorder (IRR) The Instant Recall Recorder (IRR) software with MIP 5000 allows users to record audio digitally on the MIP 5000 Operator position. Operator TX audio, Select and Unselect RX audio, Telephone Call Director Audio or any combination may be recorded. Ordering instructions for APX 7500 Mobile in a tray when used with a Digital Gateway 1. Main Model Select any Mid Power APX 7500 Mobile 2. Operation Mode Select either Operation Mode option, G241 or G System Enhancement Software Select the corresponding software option to match your system. 4. Control Head Hardware Select G88 - APX NO O5 CH NEEDED. Note: G442 - APX O5 CONTROL HEAD can be ordered for visual use of the control head but is not required for connecting to a MIP Control Head Software Select G444 - CONTROL HEAD SOFTWARE 6. Mounting Select G67 - REMOTE MOUNT MID POWER Note: The remote mount mobile is the only configuration for use with the MIP 5000.

9 Page 9 of RF Antenna Select appropriate antenna option. Note: G89 - NO RF ANTENNA NEEDED should be ordered if G88 selected in Step 4 8. Microphone Select appropriate microphone option. Note: G90 - NO MICROPHONE NEEDED should be ordered if G88 selected in Step 4 9. Speakers Select appropriate speaker option. Note: G142 - NO SPEAKER NEEDED should be ordered if G88 selected in Step Order power supply for mobile - HPN4007C Note: The power supply is not included with the mobile, this part must be ordered separately. 11. Order cable to connect radio to control head HKN6170B Note: This cable should be ordered only if G442 is selected in Step 4 Ordering Information for Aux I/Os Step 1: Order the MCN RCD Software with HIB-IP, DDN this will allow up to 4 MIP 5000 operator positions (clients) to share the I/O module status. If more than 4 operator positions are required, then the MCN SW Lic Opt Client Expansion for 4 Add'l Clients, DDN1295 is required. Step 2: Order 1 power supply CDN6116 with every HIB-IP Module. Step 3: Order the appropriate modules for the application. A maximum of 16 modules can be supported per HIB-IP. For General Purpose Aux I/Os, order DDN1385 (GPIO). Each DDN1385 cab control 12 inputs and 8 outputs. For interfacing to ASTRO-TAC Comparators, order CDN6119 (AIB) For Interfacing to SPECTRA-TAC Comparator, order CDN6121 (CIB). Step 4: Order 1 power supply, CDN6116, for every 4 modules ordered in Step 3. Example 1: If you order 2 DDN1385 and 2 CDN6119, then order 1 CDN6116 Example 2: If you order 3 DDN1385 and 2 CDN6121, then order 2 CDN6116. Step 5: Order the same number of network cables as the Quantity of modules ordered in Step 3. The following Network cable lengths are available: CABLE ASSY NETWORK 9 INCHES, CDN6123 CABLE ASSY NETWORK 3 FT, CDN6124 CABLE ASSY NETWORK 10 FT, CDN6125 CABLE ASSY NETWORK 25 FT, CDN6126 CABLE ASSY NETWORK 100 FT, CDN6127 Note: If rack mounting, the 9 inch cable should be used from module to module. To connect between rack mount shelves, the 3 FT cable should be used. Step 6: Order 2 Network Terminators, CDN6115, for every HIB (DDN1388) ordered in Step 1. Step 7: Order appropriate cabling for modules:

10 Page 10 of 15 For each GPIO and CIB module ordered in Step 3, order: 1 PUNCH BLOCK DUAL 25 PAIR, CDN CABLE ASSY 25 PR M-NONE 25FT, CDN6135 And 1 of the cables below: CBL ASSY 25 PR MALE-MALE 10 FT, CDN6129 OR CBL ASSY 25 PR MALE-MALE 25 FT, CDN6130 For each AIB module ordered in Step 3, order CBL ASSY AIB COMPARATOR 10 FT, CDN6131 Order 1 CABLE KIT HIB PC AT/XT 6 FT, DDN6132 for every system Step 8: It's recommended to order the appropriate manual for modules ordering in Step 1 and Step 3, manuals are not included with Modules. Step 1 Manuals - Both manuals are needed for DDN1388 HIB HARDWARE GUIDE, CDN6110 MCN SERVER SOFTWARE MANUAL, DDN1402 Step 3 Manuals GPIO HARDWARE GUIDE, DDN1386 AIB HARDWARE GUIDE, CDN6107 CIB HARDWARE GUIDE, CDN6109 Step 9 (Optional): Order the appropriate quantity of rack mount shelves for modules ordered in Step 1 and Step 3. DDN1387 is available to rack mount the MCN RCD HIB MODULE. Each rack mount will support 1 DDN1388 (step 1) and two additional GPIO, AIB or CIB modules (step 3). Additional rack mount shelves for the GPIO, AIB or CIB modules ordered in Step 3, can be purchased with part number CDN6112. Each CDN6112 can support up to 4 modules. Gateways MIP5000 VOIP LOCAL GATEWAY L3482AC 740 $ Provides one MIP 5000 Local Gateway. Each gateway is capable of supporting one local control radio. Punch blocks and cabling for connecting to the radio are not included in the L3482AC. An Ethernet cable (not included) is also required for each L3482AC. MIP5000 VOIP TONE GATEWAY L3483AC 740 $ Provides one MIP 5000 Tone Gateway. Each gateway is capable of supporting one tone remote controlled base station. Punch blocks and cabling for connecting to the station are not

11 Page 11 of 15 included in the L3483AC. An Ethernet cable (not included) is also required for each L3483AC. MIP5000 VOIP DIGITAL GATEWAY L3484AC 740 $ Provides one MIP 5000 Digital Gateway. Each gateway is capable of supporting one SB9600- capable radio. Punch blocks and cabling for connecting to the radio are not included in the L3484AC. An Ethernet cable (not included) is also required for each L3484AC. MIP 5000 VOIP MOTOTRBO GATEWAY L3598AC 740 $ Provides one MIP 5000 MOTOTRBO Gateway. Each gateway is capable of supporting one XPR4550 or XPR 5550 radio. Punch blocks and cabling for connecting to the radio are not included in the L3598. You must order the DDN9867 MOTOTRBO Direct Connect Cable to connect to the XPR 4550 or XPR An Ethernet cable (not included) is also required for each L3598. Options for Gateways - Must select one per gateway FOR SYSTEMS AT RELEASE 4.0 OR EARLIER TT05979AA 740 $0.00 FOR SYSTEMS AT RELEASE 4.1 OR NEWER TT05980AA 740 $0.00 Software Software ships with USB Hasp Key for license activation. Hasp key is configured to match number of channels ordered. PC, microphone, speakers and headset are not included with software and must be provided separately. MIP5000 VOIP DISPATCH SW 1 CHANNEL L $1, Provides the software application and license for one MIP channel dispatch console. Allows a dispatcher to access and control one MIP 5000 Local, Tone, Digital, or MOTOTRBO Gateway. MIP5000 VOIP DISPATCH SW 4 CHANNEL L $2, Provides the software application and license for one MIP channel dispatch console. Allows a dispatcher to access and control up to four MIP 5000 Local, Tone, Digital, or MOTOTRBO Gateways. MIP5000 VOIP DISPATCH SW 8 CHANNEL L $6, Provides the software application and license for one MIP channel dispatch console. Allows a dispatcher to access and control up to eight MIP 5000 Local, Tone, Digital, or MOTOTRBO Gateways. MIP5000 VOIP DISPATCH SW 12 CHANNEL L $10, Provides the software application and USB Hasp Key for one MIP channel dispatch console. Allows a dispatcher to access and control up to 12 MIP 5000 Local, Tone, Digital, or MOTOTRBO Gateways. MIP5000 VOIP 24 CHANNEL SW WITH LICENSE L $15, Provides the software application and USB Hasp Key for one MIP channel dispatch console. Allows a dispatcher to access and control up to 24 MIP 5000 Local, Tone, Digital, or MOTOTRBO Gateways. MIP5000 VOIP DISPATCH SW 48 CHANNEL L $25, Provides the software application and USB Hasp Key for one MIP channel dispatch console. Allows a dispatcher to access and control up to 48 MIP 5000 Local, Tone, Digital, or MOTOTRBO Gateways. Options for Software MIP5000 BASIC MODEL USB HEADSET JACKBOX TT05515AA 740 $ MIP5000 ENHANCED MODEL USB HEADSET JACKBOX TT05522AA 740 $ Expansion Entitlement MIP5000 SW EXPANSION ENTITLEMENT 4 TO 24 CHANNELS TT $13, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 4 TO 12 CHANNELS TT $8, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold.

12 Page 12 of 15 MIP5000 SW EXPANSION ENTITLEMENT 8 TO 24 CHANNELS TT $9, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 12 TO 24 CHANNELS TT $5, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 8 TO 12 CHANNELS TT $4, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 4 TO 48 CHANNELS TT $23, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 8 TO 48 CHANNELS TT $19, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 12 TO 48 CHANNELS TT $15, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. MIP5000 SW EXPANSION ENTITLEMENT 24 TO 48 CHANNELS TT $10, Orders for this item will automatically be placed on hold. Be prepared to provide the Factory Order (FO) number and/or the Serial number of the currently installed software to release the hold. Demo MIP CHANNEL DEMO SOFTWARE L $ THE 4 CHANNEL MIP 5000 DEMO SOFTWARE IS NOT FOR RESALE. IT PROVIDES SOFTWARE TO DEALERS AT A SIGNIFICANT DISCOUNT AND IS LIMITED TO 1 PER CHANNEL PARTNER LOCATION. TO COMPLETE THE DEMO SYSTEM, ORDER THE FOLLOWING ADDITIONAL COMPONENTS: 1) UP TO 4 MIP 5000 GATEWAYS (L3482 LOCAL, L3483 TONE, L3484 DIGITAL, L3598 MOTOTRBO) 2) DDN8671 NULL MODEM CABLE FOR PROGRAMMING THE GATEWAY. 3) DDN9492 BASIC USB HEADSET JACKBOX, 4) B1914 DESKTOP GOOSENECK MICROPHONE. 5) MOBILE RADIO WITH RADIO INTERFACE CABLES TO CONNECT THE GATEWAY TO THE RADIO 6) A DESKTOP OR LAPTOP COMPUTER MEETING MIP 5000 SPECIFICATIONS 7) A SET OF PC SPEAKERS 8) SUBSCRIBER TO DEMONSTRATE RX AND TX AUDIO Computers Z420 LOW TIER WORKSTATION WINDOWS 7 TT $2, Provides a HP Z420 computer with the Windows 7 (64 bit) operating system, a keyboard and a mouse. Does not include a monitor or any application software. Not compatible with GPIOM based MCC 7500 consoles (it doesn't have enough PCI slots and doesn't support Vista or XP O/Ss).Does not support Hardware Encrypt Key Mgmt on MCC Accessories

13 Page 13 of 15 Audio MIP5000 BASIC MODEL USB HEADSET JACKBOX DDN $ Supports 1 Plantronics two prong headset base and quick disconnect top, 1 footswitch BLN6732 and 1 gooseneck Microphone B1914 MIP5000 ENHANCED MODEL USB HEADSET JACKBOX DDN $ Supports 1 Plantronics two prong headset base and quick disconnect top, 1 footswitch BLN6732 and 1 gooseneck Microphone B1914, also provides port for Call Director, logging Recorder or External Pager port. MCC SERIES DESKTOP GOOSENECK MICROPHONE B $ Provides one desktop style microphone. Includes transmit and monitor buttons, an 18" gooseneck shaft and a 10 foot cable. Compatible for use near CRT monitors. FOOT, SWITCH TRADITIONAL BLN $ CREATIVE LABS INSPIRE A60 CDN $46.00 Creative Lab speakers includes 110V AC power supply. MOTOTRBO (L3598) Direct Connect Radio Interface Cable MOTOTRBO DIRECT CONNECT CABLE DDN $ For use with the XPR 4550 or XPR Digital Gateway (L3484) Radio Interface Cables APX 7500 MOBILE DIRECT CONNECT CABLE DDN $ MCS2000 III DIRECT CONNECT CABLE DDN $ CONSOLETTE W9 DIRECT CONNECT CABLE DDN $ CDM1550 SERIES DIRECT CONNECT CABLE DDN $ Local Gateway (L3482) Control Interface Cables RADIO INTERFACE CABLE 4 USE WITH MAXTRAC, M1225, SM50, DDN $72.00 SM120, CDM1550 For connecting MAXTRAC, M1225, SM50, SM120, CDM750, CDM1250, and CDM1550 family radios. With Local Junction Box (DDN6337) and TRC/DC Remote Adapters (L3276/L3277) GENERIC RADIO CABLE WITH UNTERMINATED BARE LEADS DDN $50.00 For use with Local Junction Box (DDN6337) and TRC/DC Remote Adapters (L3276/L3277). Provides 10FT cable with DB 25 connector on one end. RADIO INTERFACE CABLE FOR THE MCS2000 DDN $ FRU Kits 15 FT NULL MODEM CABLE DB9 F/F DDN $13.75 One required per MIP 5000 System Rackmount Kit MIP5000 RACKMOUNT KIT DDN $225.00

14 Page 14 of 15 Holds 2 gateways Information Assurance (Only compatible with the TT2538 Computer) MIP5000 INFORMATION ASSURANCE TRANSPARENT HARDENING TT $50.00 KIT CD MIP5000 INFORMATION ASSURANCE FULLY HARDENED KIT CD TT $50.00 Aux I/Os MCN Modules MCN RCD SERVER SOFTWARE AND HIB-IP MODULE DDN $7, MCN GPIO-1208C INPUT/OUTPUT MODULE DDN $1, AIB ASTROTAC INTERFACE MODULE CDN $1, CIB COMPARATOR INTFC MODULE CDN $ Software Expansion MCN SW LIC OPT CLIENT EXPANSION FOR 4 ADD'L CLIENTS DDN $2, Power Supply POWER SUPPLY MCN120 VAC CDN $66.00 Network Cables and Terminators CABLE ASSY NETWORK 9 INCHES CDN $21.00 CABLE ASSY NETWORK 3 FT CDN $21.00 CABLE ASSY NETWORK 10 FT CDN $21.00 CABLE ASSY NETWORK 25 FT CDN $38.00 CABLE ASSY NETWORK 100 FT CDN $92.00 NETWORK TERMINATOR (STANDARD 78K SYSTEMS) CDN $12.00 Parallel Input/Output Cables CBL ASSY 25 PR MALE-MALE 10 FT CDN $86.00

15 Page 15 of 15 CBL ASSY 25 PR MALE-MALE 25 FT CDN $98.00 Serial Cables CBL ASSY 25 PR MALE-MALE 25 FT CDN $98.00 Manuals HIB-232 HARDWARE GUIDE CDN $20.00 MCN SERVER SOFTWARE MANUAL DDN $25.00 GPIO HARDWARE GUIDE DDN $20.00 AIB HARDWARE GUIDE CDN $20.00 CIB HARDWARE GUIDE CDN $20.00 Rack Mounting RACK MOUNT FOR HIB-IP DDN $75.00 RACK MOUNT QUAD SIZE A CDN $92.00 Data Compiled 02-Feb-2015 using DUP and all prices in USD

16 Dispatch Solutions \ Dispatch Computer Hardware mk:@msitstore:c:\users\case02\documents\ecat_dup_feb_2015\ecat.chm::/comp_m... Page 1 of 3 MCC 7500, MCC 7100, MCC 5500 and MIP 5000 Consoles Computer Hardware Options and Accessories RF-Certified LCD Monitors (Touch and Non-Touch) Ship Card Models, Options, Accessories, and FRU's CLIENT WORKSTATION MODELS Z420 LOW TIER WORKSTATION WINDOWS 7 TT $2, Provides a HP Z420 computer with the Windows 7 (64 bit) operating system, a keyboard and a mouse. Does not include a monitor or any application software. Not compatible with GPIOM based MCC 7500 consoles (it doesn't have enough PCI slots and doesn't support Vista or XP O/Ss).Does not support Hardware Encrypt Key Mgmt on MCC For PC Anywhere information see the Network Security ECAT pages. CLIENT OPTIONS ADD: DUAL IRR CARD & PC SPKER ZA00268AB 708 $ This option adds the PCI Express X-Fi Xtreme Fidelity sound card. SERVERS The ML 110-G6 WITH WIN2003 SERVER (DDN1065) is no longer available. Customers looking to replace a WIN2003 SERVER will have to upgrade to WIN2008 SERVER. The ML110-G7 WITH WIN2008 SERVER (TT2322) and the ML310e Gen8 WIN2008 SERVER (TT2605) are no longer available. Please use the ML310E GEN8V2 SERVER WINDOWS SERVER (TT2739). ML310E GEN8V2 SERVER WINDOWS SERVER 2008 R2 (SP1 64- TT $5, BIT) Client Access Licenses ADDITIONAL 5 CLENT ACCESS LICENSES / WINDOWS/ 0 SERVER L $ (NO MEDIA) 20 CLENT ACCESS LICENSES / WINDOWS SERVER (NO MEDIA) L $1, Monitors All monitors are RF-CERTIFIED by Console Engineering and are suitable for use with MCC 7500, MCC 5500 and MIP 5000 consoles. All ISPO monitors are VESA compliant. Image retention may occur when using LCD monitors in a 24/7, no-screensaver environment. Please contact Shannon Fowler ( ) for more information.

17 Dispatch Solutions \ Dispatch Computer Hardware Page 2 of 3 STANDARD FORMAT MONITORS (4:3 Aspect Ratio) NON-TOUCH MONITORS 17 INCH NON-TOUCH MONITOR, BLACK DS017BLK 708 $1, INCH NON-TOUCH MONITOR, BLACK DS019BLK 708 $1, Black, Std. format, 4:3 aspect ratio TOUCH MONITORS Multi-touch monitors may be used with the following consoles on the specified releases. Note that the multi-touch gestures themselves are not supported. Only the legacy touch operations are supported. MCC 7500/7100 with system release 7.13 and later MCC 5500 with system release 2.7 and later MIP 5000 with system release 4.2 and later Multi-touch monitors are not supported for use with Gold Elite consoles in any system releases. 17 INCH MONITOR WITH TOUCH SCREEN, BLACK DS017BLKTS 708 $2, ELO 1928L 19IN LCD TOUCH MONITOR, DUAL SERIAL USB CONTROLLER, GRAY DSE $2, WIDE FORMAT MONITORS (16:9 Aspect Ratio) NON-TOUCH MONITORS 22 INCH WIDE NON-TOUCH MONITOR, BLACK DS22WBLK 708 $3, Black, Wide format, 16:9 aspect ratio TOUCH MONITORS Multi-touch monitors may be used with the following consoles on the specified releases. Note that the multi-touch gestures themselves are not supported. Only the legacy touch operations are supported. MCC 7500/7100 with system release 7.13 and later MCC 5500 with system release 2.7 and later MIP 5000 with system release 4.2 and later Multi-touch monitors are not supported for use with Gold Elite consoles in any system releases. 22 INCH WIDE WITH TOUCH SCREEN MONITOR, BLACK DS22WBLKTS 708 $4, MOUSE/TRACKBALL (ACCESSORIES) TRACKERBALL (ONLY PS/2 & USB COMPATIBLE) DSCDN6171B 708 $ Trackball is "ruggedized" and "RF-CERTIFIED" by Consoles Engineering. Order as a main line item. MISCELLANEOUS mk:@msitstore:c:\users\case02\documents\ecat_dup_feb_2015\ecat.chm::/comp_m...

18 Dispatch Solutions \ Dispatch Computer Hardware mk:@msitstore:c:\users\case02\documents\ecat_dup_feb_2015\ecat.chm::/comp_m... Page 3 of 3 PS/2 KEY/MOUSE EXT MINI DIN 6FT DSPCM $25.00 STANDARD IEC AC POWER CORD 12 FOOT DSPWR $20.00 Data Compiled 02-Feb-2015 using DUP and all prices in USD