Figure A scenario architecture graph. Vigor3300 Series Application Note V
|
|
- Primrose Stanley
- 8 years ago
- Views:
Transcription
1 29. VoIP Example 2 (Basic Calling Method) We will introduce three basic VoIP calling methods, involving Direct IP Call, Intercommunication with one SIP Proxy Server and Intercommunication with different SIP Proxy Servers. All the settings are based on the VoIP Example 1(Basic Configuration and Registration) Direct IP Call (Call with each other without registration) Connect a telephone into 3300V's Port 1 and 2900V's Port 1 respectively. They can call with each other directly with IP addresses if only 3300V and 2900V both have public IP addresses and have set up the Phone Numbers. Figure A scenario architecture graph Vigor3300 Series Application Note V
2 Table Configuration table WAN IP Port Number Phone Number Proxy Codec 3300V Port1(FXS) iptel G.729A 2900V Port1(FXS) iptel G.729A Furthermore, do NOT enable the Outbound Proxy feature when you set up 3300V and 2900V to use Direct IP Call. (It isn't active in the Example 1; please see Figure 30-2 shown below) Otherwise even if you dial the IP address, the call is still sent to the SIP Proxy Server always. And if the SIP Proxy Server doesn't forward the call to remote VoIP user's WAN IP, you can't do this action Figure Outbound proxy feature 3300V Configuration Example 1. Enter VoIP - Speed Dial page, configure relevant settings for 2900V's Port1. Speed Dial Phone Number: type Speed Dial Destination: Cal lee s Number@IP, type @ Memo: To facilitate ease differentiation please type 2900V_Port1_IP. Click Apply to save the settings and finish the configuration. Figure Speed dial port 1 setting 174 Vigor3300 Series Application Note V2.2
3 2900V Configuration Example 1. Click DialPlan Setup in the VoIP Setup page. 2. Click Index 1. Figure DialPlan setting of Vigor2900V Figure DialPlan configuration of Vigor2900V 3. Enter relevant settings for 3300V's Port 1. Click OK to save the settings. Enable: click ( ) to activate the entry. Phone Number: type Display Name: To facilitate ease differentiation please type 3300V_Port1_IP. SIP URL: Cal lee s Number@IP, please type @ Figure Enter relevant settings of index1 Vigor3300 Series Application Note V
4 4. Confirm the settings are correct, and then finish the configuration. Start to dial by using telephones. Figure Finish DialPlan configuration Phone 1 calls Phone 2 --->Press 2901# or *61*31*167*135#. Phone 2 calls Phone 1--->Press 3301#. Note: # indicates termination of the phone number. After pressing #, VoIP is immediately called out. Or you may wait 3 seconds if you do not press #. With 2900V you can't only dial alphanumeric addresses symbols. To dial an IP address, start and end it with a # (hash) replace the dots with * (star). In this example you have to press #220*135*240*207#. But 3300V can only receive the format of Number@IP. So it is required to setup 3300V's number (888833@ ) in the DialPlan entry. 176 Vigor3300 Series Application Note V2.2
5 29.2 Intercommunication with one SIP Proxy Server (registration) Connect telephones into 3300V's Port 1 & Port 3 and 2900V's Port 1 & Port 2 respectively. Each port needs to register in the SIP Server. Figure A scenario architecture graph Table Configurations between Vigor 3300V and 2900V WAN IP Port Number Phone Number Proxy Codec Port1(FXS) iptel G.729A 3300V 7 Port3(FXS) fwd G.729A Port1(FXS) iptel G.729A 2900V Port2(FXS) fwd G.729A You can also add Speed Dial numbers in Speed Dial to speed up the dialing, or to accommodate the setup of company's extension numbers. Vigor3300 Series Application Note V
6 3300V Configuration Example 1. Enter the VoIP - Speed Dial page and add the second and third group of Speed Dial number. Then click Apply to save the settings and finish the configuration. Start to dial by using telephones. Figure Speed dial port 2 and port 3 settings Phone 1 call Phone 3---> Press # or 291#. Phone 2 call Phone 4--->Press # or 292#. Phone 3 call Phone 1--->Press #. Phone 4 call Phone 2--->Press #. Note: # indicates termination of the phone number. After pressing #, VoIP is immediately called out. Or you may wait 3 seconds if you do not press #. 178 Vigor3300 Series Application Note V2.2
7 29.3 Intercommunication with different SIP Proxy Servers Connect telephones into 3300V's Port 1 & Port 3 and 2900V's Port 1 & Port 2 respectively. Each phone registers to the SIP Server. The settings and scenario are the same as the above example. But they must be set up in conjunction with the Speed Dial. 3300V Configuration Example 1. Enter the VoIP - Speed Dial page and add the 4th and 5th group of Speed Dial number. Then press Apply to save the settings and finish the configuration. 2900V Configuration Example Figure Speed dial port 4 and port 5 settings 1. Click DialPlan Setup in the VoIP Setup page. Then add the second and third group of Speed Dial number. Figure DialPlan configuration of index 2 and index 3 Start to dial by using telephone. Phone 1 call Phone 4--->Press 2912#. Phone 2 call Phone 3--->Press 2911#. Phone 3 call Phone 1--->Press 3312#. Phone 4 call Phone 2--->Press 3311#. Note: # indicates termination of the phone number. After pressing #, VoIP is immediately called out. Or you may wait 3 seconds if you do not press #. Vigor3300 Series Application Note V
8 180 Vigor3300 Series Application Note V2.2
VoIP Example 2 (Basic Calling Method)
VoIP Example 2 (Basic Calling Method) This chapter shows another application example in VoIP function. This chapter is divided into the following sections, Section 30.1: Direct IP Call (Call with each
More informationFigure 30-1. A scenario architecture graph
30. VoIP Example 2 (Basic Calling Method) This chapter shows another application example in VoIP function. This chapter is divided into the following sections, Section 30.1: Direct IP Call (Call with each
More informationBased on the VoIP Example 1(Basic Configuration and Registration), we will introduce how to dial the VoIP call through an encrypted VPN tunnel.
30. VoIP Example 3 (VoIP over VPN) Based on the VoIP Example 1(Basic Configuration and Registration), we will introduce how to dial the VoIP call through an encrypted VPN tunnel. In this example 3300V
More informationVersion : 2.0 Date : 2006/6/12
Version : 2.0 Date : 2006/6/12 i Table of Contents Chapter 1. High Availability Function... 1 1.1 Introduction... 1 1.2 Examples and Web Configurations... 2 Chapter 2. VPN Function... 4 2.1 VPN Dial-in
More informationTable 28-1. Example 1-basic settings in Vigor 3300V and 2900V. WAN IP Port Number Phone Number Proxy Codec
28. VoIP Example 1 (Basic Configuration and Registration) There are many different kinds of applications about VoIP function, most of VoIP callings must be via a VoIP Server by registering, except we can
More informationNF1Adv VOIP Setup Guide (for Pennytel)
NF1Adv VOIP Setup Guide (for Pennytel) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network
More informationCopyright ZYCOO All Rights Reserved 1 / 8
Copyright ZYCOO All Rights Reserved 1 / 8 If you have a scenario where you have two CooVox IP PBXs in two different locations then you can integrate them together to make free phone calls between locations.
More informationNF1Adv VOIP Setup Guide (for Generic VoIP Setup)
NF1Adv VOIP Setup Guide (for Generic VoIP Setup) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer
More informationIntercommunication between two MyPBX (via VoIP Trunking)
Intercommunication between two MyPBX (via VoIP Trunking) 1. Connect two MyPBX in the same network... 2 2. Connect two MyPBX in different locations... 8 2.1 Connect two MyPBX via SIP Trunking... 9 2.2 Connect
More informationTHINKTEL COMMUNICATIONS TALKSWITCH VS TALKSWITCH VS THINKTEL SIP TRUNK & DID
THINKTEL COMMUNICATIONS TALKSWITCH VS TALKSWITCH VS THINKTEL SIP TRUNK & DID TA B L E O F C O N T E N T S 1.1 INTRODUCTION... 3 1.2 STARTING THE MANAGEMENT SOFTWARE... 4 1.3 IP CONFIGURATION... 5 1.4 ROUTER
More informationConfiguring 3CX for Spitfire SIP Trunks
Configuring 3CX for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto a 3CX which includes the settings required for Inbound DDI routing and Outbound CLI presentation.
More informationPeer-to-Peer SIP Mode with FXS and FXO Gateways
Peer-to-Peer SIP Mode with FXS and FXO Gateways New Rock s SIP based VoIP gateways with FXS and FXO ports support peer-to-peer mode which has many applications in deploying enterprise multi-site telephone
More informationQuick Installation Guide
Quick Installation Guide MegaPBX Version 2.1 Quick Installation Guide v2.1 www.allo.com 2 Table of Contents Initial Setup of MegaPBX... 4 Notification LEDs (On the Front Panel of the Gateway)... 5 Create
More informationScenario 1: One-pair VPN Trunk
VPN Trunk Load-Balance between Vigor3200 and Other Vigor Router This section will discuss how to build VPN Trunk with load-balance between Vigor3200 and other router (e.g., Vigor3300). Scenario 1: One-pair
More informationConfiguration Note for Jeron Provider 790 and Cisco CallManager
Configuration Note for Jeron Provider 790 and Cisco CallManager 1. Jeron Provider 790 Setup 1.1 Configure the SIP Server Connectivity Set Brekeke SIP Server's IP address in the [SIP Server IP] field and
More informationConfigure your 3CX in our IP telephone service.
Configure your 3CX in our IP telephone service. This user guide will explain how to configure a 3CX Phone System turning into a small office with three extensions (1000, 1001 y 1002) and connect with Netelip
More informationNF5 VOIP Setup Guide (for Generic)
NF5 VOIP Setup Guide (for Generic) Configuring your NF5 for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings:
More informationHow to Configure the Allworx 6x, 24x and 48x for use with Integra Telecom SIP Solutions
How to Configure the Allworx 6x, 24x and 48x for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Allworx 6x IP PBX to connect to Integra Telecom
More informationDSX. DSX SIP Setup. April 22, 2011 Issue 1.04. NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484
DSX DSX SIP Setup April 22, 2011 Issue 1.04 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402 Communications
More information3rd Party VoIP Phone Setup Guide (Panasonic 500-550b)
3rd Party VoIP Phone Setup Guide (Panasonic 500-550b) We are changing how we add 3rd party VoIP phones to accounts. Going forward, you can simply add a 3rd Party Softphone and use those credentials to
More informationIntercommunication between two MyPBX (via VoIP Trunk)
Intercommunication between two MyPBX (via VoIP Trunk) 1. Link two MyPBX in the same network... 2 2. Link two MyPBX in different location... 6 2.1 Link two MyPBX via IAX Trunk... 7 2.2 Link two MyPBX via
More informationWave SIP Trunk Configuration Guide FOR BROADVOX
Wave SIP Trunk Configuration Guide FOR BROADVOX Last updated 1/7/2014 Contents Overview... 1 Special Notes... 1 Before you begin... 1 Required SIP trunk provisioning and configuration information... 1
More informationTHINKTEL COMMUNICATIONS 3CX PHONE SYSTEM V.11. 3CX Phone System THINKTEL SIP TRUNK from scratch
THINKTEL COMMUNICATIONS 3CX PHONE SYSTEM V.11 3CX Phone System THINKTEL SIP TRUNK from scratch TA B L E O F C O N T E N T S 1.1 INTRODUCTION... 3 2.1 REQUIREMENTS... 4 2.2 3CX PHONE SYSTEME INSTALLATION...
More information3CX PBX v12.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. VoIP Provider Setup
More informationAvaya IP Office 8.1 Configuration Guide
Avaya IP Office 8.1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Revision: 1.1 Date: 10/14/2013 Copyright 2013 by tekvizion PVS, Inc. All Rights Reserved.
More informationInternet Telephony PBX System
Internet Telephony PBX System IPX-600 Copyright PLANET Technology Corporation. All rights reserved. This installation guide introduces several practical configuration examples of IP PBX deployment. The
More informationVintalk SIP Trunk Setup
DSX Vintalk SIP Trunk Setup April 23, 2011 Issue 1.00 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402
More informationStep 1: Checking Computer Network Settings:
Configuring your 3G18WV for VOIP The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings: You will need to connect your computer
More informationTALKSWITCH VOIP NETWORK TROUBLESHOOTING GUIDE
TALKSWITCH DOCUMENTATION TALKSWITCH VOIP NETWORK TROUBLESHOOTING GUIDE RELEASE 3.24 CT.TS005.008001 ANSWERS WITH INTELLIGENCE COPYRIGHT INFORMATION TalkSwitch. Copyright 2006. All Rights Reserved. Reproduction,
More informationQuick Installation Guide
Quick Installation Guide PRI Gateway Version 2.4 Table of Contents Hardware Setup... 1 Accessing the WEB GUI... 2 Notification LEDs (On the Front Panel of the Gateway)... 3 Creating SIP Trunks... 4 Creating
More informationTeletics Application Note. Using the Feature Server with SIP Trunks
Teletics Application Note Using the Feature Server with SIP Trunks Rev 1.0 June 4 2012 Teletics Application Note Using the Feature Server with SIP Trunks Page 1 Executive Summary One of the key advantages
More informationNF3ADV VoIP Setup Guide (for TPG)
NF3ADV VoIP Setup Guide (for TPG) Configuring your NF3ADV for TPG VoIP The following steps will take you through the process of setting up your VoIP connection. This guide assumes that the NF3ADV already
More informationSUTUS Business Central 5800 ThinkTel Configuration
SUTUS Business Central 5800 ThinkTel Configuration This document explains how to configure SUTUS Business Central 5800 to connect to the ThinkTel VoIP service. Configuring SUTUS Business Central 5800 to
More informationQuick Start Guide CREATING A NEW SITE
IVY is our complete control panel for managing you or your customers SIP trunks and hosted PBX settings. This guide will help you get up and running with IVY as quickly as possible. First thing we need
More informationHow to access peers with different VPN through IPSec. Tunnel
How to access peers with different VPN through IPSec Tunnel Scenario: Taipei branch and Kaohsiung branch dial to Hsinchu headquarter via IPSec VPN Tunnel respectively. Both Taipei branch and Kaohsiung
More information3CX Guide sip.orbtalk.co.uk
3CX Guide sip.orbtalk.co.uk Table of Contents 1. Outbound Dialling 2. Inbound Routing 3. Outbound CLI 4. Additional Network Configuration 1. Outbound dialling: The Customer will have been provided with
More informationVoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
VoiceGear/3CX Integration Guide Ver.0.1 Page 2 1. OVERVIEW... 3 1.1 SETTING UP 3CX PBX...4 1.2 SETTING UP VOICEGEAR GATEWAY...5 2. VOICEGEAR-3CX SIP INTEGRATION... 6 2.1 3CX CONFIGURATION...7 2.2 VOICEGEAR
More informationDinstar GSM VoIP Gateway Interoperability Guide. DWG and 3CX System
Dinstar GSM VoIP Gateway Interoperability Guide DWG and 3CX System Shenzhen Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518052 Telephone:
More informationDSX. ATC SIP Trunk Setup. April 22, 2011 Issue 1.01. NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484
DSX ATC SIP Trunk Setup April 22, 2011 Issue 1.01 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402
More information3rd Party VoIP Phone Setup Guide (Panasonic UT113-123)
3rd Party VoIP Phone Setup Guide (Panasonic UT113-123) We are changing how we add 3rd party VoIP phones to accounts. Going forward, you can simply add a 3rd Party Softphone and use those credentials to
More informationAvaya IP Office SIP Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with SIP-enabled versions of Avaya IP Office (5.0 and higher). The Valcom device is added to the IP Office system as a SIP Extension.
More informationExcel SIP Trunk Setup
DSX Excel SIP Trunk Setup April 22, 2011 Issue 1.04 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402
More informationLoad Balance Mechanism
Load Balance Application in Dual-WAN Interface Load Balance Mechanism To which WAN port the traffic will be routed is determined according to the Load Balance mechanism. Below diagram shows how Vigor router
More informationWave 500 IP PBX v4.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Wave 500 IP PBX v4.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Wave 500 IP PBX v4.5 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. Inbound/Outbound
More informationHow To Set Up Virtual Fax On Zcoo (U20/50/60/100) On A Pc Or Macbook Or Ipod (U21/50) On An Ipod Or Ipo (U19/50 Or 60
ZYCOO new generation IP Phone system---coovox Series (U20/50/60/100) support virtual fax. Virtual fax is an important feature to help enterprise reduce the cost and promote the efficient communication.
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
More informationGrandstream Networks, Inc.
Grandstream Networks, Inc. UCM6100 Basic Configuration Guide Grandstream Networks, Inc. www.grandstream.com TABLE OF CONTENTS OVERIEW... 4 SETUP GUIDE SCENARIO... 4 QUICK INSTALLATION... 5 Connecting the
More informationnexvortex Setup Template
nexvortex Setup Template ZULTYS, INC. April 2013 5 1 0 S P R I N G S T R E E T H E R N D O N V A 2 0 1 7 0 + 1 8 5 5. 6 3 9. 8 8 8 8 Introduction This document is intended only for nexvortex customers
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502
PANASONIC SIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationMicronet VoIP Solution with Asterisk
Application Note Micronet VoIP Solution with Asterisk 1. Introduction This is the document for the applications between Micronet units and Asterisk IP PBX. It will show you some basic configurations in
More informationInternet Telephony PBX System
Internet Telephony PBX System GSM Gateway PSTN call busy forward to GSM Configuration Copyright PLANET Technology Corporation. All rights reserved. Case 32: PSTN call busy forward to GSM Configuration
More informationAvaya IP Office SIP Trunk Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with SIP-enabled versions of Avaya IP Office (5.0 and higher). The Valcom device can be added to the IP Office system as a SIP Trunk.
More informationHow to Connect SSTP VPN from Windows Server 2008/Vista to Vigor2950
How to Connect SSTP VPN from Windows Server 2008/Vista to Vigor2950 Requirements Windows Server 2008, or Windows Vista SP1 Local Certificate (a online CA server on the Internet is required for some situation
More informationwww.xo.com XO SIP Service Customer Configuration Guide for Interactive Intelligence Customer Interaction Center (CIC) with XO SIP
www.xo.com XO SIP Service Customer Configuration Guide for Interactive Intelligence Customer Interaction Center (CIC) with XO SIP Table of Contents XO SIP Service 1 1 Introduction... 3 2 Executive Summary...
More informationSIP Internet Telephony Gateway
SIP Internet Telephony Gateway VIP - 2 / 4 / 8 / 16 / 24 Series Peer-to-Peer Quick Configuration for VIP-450 Copyright PLANET Technology Corporation. All rights reserved. Scenarios explain: Peer-to-Peer
More informationSIP Server Installation (Mayah example)
Application Note 27 SIP Server Installation (Mayah example) Table of contents 1 GENERAL... 2 2 ENVIRONMENT... 2 2.1 SCHEMATIC DIAGRAM... 2 2.2 USED EQUIPMENT... 3 2.3 USED INFRASTRUCTURE... 3 3 CONFIGURATION
More informationTHINKTEL COMMUNICATIONS CUDATEL PHONE SYSTEM 270. High Availability and SIP-TRUNK Configuration
THINKTEL COMMUNICATIONS CUDATEL PHONE SYSTEM 270 High Availability and TABL E OF CO NTENTS 1.1 CONFIGURING TELEPHONE SERVICE PROVIDER (THINKTEL)... 3 1.2 OUTBOUND CALL ROUTING... 5 1.3 INBOUND CALL FROM
More information3CX Version 8.x - Multiple SIP Trunk configuration to XeloQ Communications / GoAndCall.com
3CX Version 8.x - Multiple SIP Trunk configuration to XeloQ Communications / GoAndCall.com Note: Go to page 13 if you would like to receive multiple DID s on 1 XeloQ SIP Trunk; that is also possible and
More informationConfiguring Avaya BCM 6.0 for Spitfire SIP Trunks
Configuring Avaya BCM 6.0 for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto Business Communication Manager release 6.0 and includes the settings required for
More informationCONFIGURING TALKSWITCH FOR RUBICON SERVICE
TALKSWITCH TECH NOTE CONFIGURING TALKSWITCH FOR RUBICON SERVICE CONFIGURING TALKSWITCH FOR RUBICON SERVICE CT.TS005.004502 Before proceeding, we recommend that you follow the steps outlined in the Start
More informationHow to setup Mobility Extension on the 2N OfficeRoute and 2N VoiceBlue Enterprise
How to setup Mobility Extension on the 2N OfficeRoute and 2N VoiceBlue Enterprise This is the manual for a firmware version 2.2.9 Our scenario: 1. Firstly you need to set up the IP address of the OfficeRoute
More informationOptimum Business SIP Trunk Set-up Guide
Optimum Business SIP Trunk Set-up Guide For use with IP PBX only. SIPSetup 07.13 FOR USE WITH IP PBX ONLY Important: If your PBX is configured to use a PRI connection, do not use this guide. If you need
More informationHow to add a SIP server How to register a handset
How to add a SIP server How to register a handset Contents Contents... 1 Hardware required equipment... 2 Software required equipment... 3 Add server... 3 Register handset to base... 7 1 of 12 Hardware
More informationKnowledgebase Solution
Knowledgebase Solution Updated: 2/27/2014 Configuring an EdgeMarc for SIP trunking with an IP PBX This document describes the steps needed to configure an IP PBX behind the EdgeMarc which is pointing to
More informationOfficeServ 7100 IP-PBX. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Samsung
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Samsung OfficeServ 7100 IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. OfficeServ 7100 PBX Configuration 3 3.1 Network
More informationMediatrix 3000 with Asterisk June 22, 2011
Mediatrix 3000 with Asterisk June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Network Topology... 3 Equipment Detail... 3 Configuration of the Fax Extension... 4 Configuration
More informationInternet Telephony PBX System
Internet Telephony PBX System T1/E1 Gateway With IP PBX Application Copyright PLANET Technology Corporation. All rights reserved. Case 35: With IP PBX Application Head Office E1 PABX interconnect with
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationDirect IP Calls. Quick IP Call Mode
Unicorn3112 Tips Direct IP Calls...1 Quick IP Call Mode...1 PSTN Pass Through...2 VoIP-to-PSTN Calls...2 PSTN-to-VoIP Calls...3 Route Calls to PSTN...4 Forward Calls to PSTN...4 Forward Calls to VoIP...4
More informationEcessa Proxy VoIP Manual
Ecessa Proxy VoIP Manual Table of Contents Introduction...1 Configuration Overview...2 VoIP failover requirements...2 Import VoIP Authentication...3 Add a user manually...3 Setup...3 Hosted setup...3 Example
More informationGrandstream Networks, Inc. UCM6510 Basic Configuration Guide
Grandstream Networks, Inc. UCM6510 Basic Configuration Guide Index Table of Contents OVERVIEW... 4 SETUP ENVIRONMENT... 5 QUICK INSTALLATION... 6 CONNECT UCM6510... 6 ACCESS UCM6510 WEB INTERFACE... 6
More informationIP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
More informationRingCentral Office. Configure Aastra phones with RingCentral
TM RingCentral Office Configure Aastra phones with RingCentral Configuring Aastra phones Overview... 2 Getting ready to setup your Aastra phones... 2 Configuring the Aastra Phone... 4 Overview Aastra s
More informationV101 SIP VoIP Telephone Adaptor User Manual V1.1m
V101 SIP VoIP Telephone Adaptor User Manual V1.1m Quick Guide Step 1: Broadband (ADSL/Cable Modem) Connections for V101 A. Connect V101 LAN port to ADSL NAT Router as the following connection. B. Connect
More informationMITEL SIP CoE. Technical. Configuration Notes. Configure Ascom i62 phones for use with MiVoice Office. SIP CoE 14-4940-00310
MITEL SIP CoE Technical Configuration Notes Configure Ascom i62 phones for use with MiVoice Office SIP CoE 14-4940-00310 NOTICE The information contained in this document is believed to be accurate in
More informationHow to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions
How to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Toshiba Strata CIX IP PBX to connect to Integra
More informationGrandstream Networks, Inc. How to Integrate UCM6100 with Microsoft Lync Server
Grandstream Networks, Inc. How to Integrate UCM6100 with Microsoft Lync Server Index Table of Contents OVERVIEW... 3 UCM6100 CONFIGURATION... 4 STEP 1: CREATE SIP PEER TRUNK... 4 STEP 2: CONFIGURE OUTBOUND
More informationPrestige 2302R Series
VoIP Station Gateway Quick Start Guide Version 3.60 6/2005 Overview This Quick Start Guide covers the Prestige (P2302R) and (P2302RL) models. It explains how to use your Prestige to make phone calls through
More informationConfiguring an Etherspeak SIP Trunk in Microsoft Lync 2013
Configuring an Etherspeak SIP Trunk in Microsoft Lync 2013 This is to cover the steps needed for basic functionality to communicate with Etherspeak s SIP trunking service. Many environments are different
More informationConnecting with sipgate
Connecting with sipgate sipgate (http://www.sipgate.co.uk/) offers telephone service using the VoIP standard SIP. sipgate covers every area code within the United Kingdom and provides a local Direct Inward
More informationSIP Trunk Configuration Guide. using
SIP Trunk Configuration Guide using www.cbeyond.net 1-877-441-9783 The information contained in this document is specific to setting up SIP connections between Vertical SBX IP 320 and Cbeyond. If you require
More informationHow to register your wired (wireless) Phone to IPX-300W
How to register your wired (wireless) Phone to IPX-300W In the following samples, we ll introduce IP Phone and Wi-Fi Phone register to IP PBX applications. Topology of instruction example Machine Configuration:
More informationAudiaFLEX Voice-over-IP Interface. Preliminary Steps. Configuring a Cisco CallManager system to work with Biamp s VoIP-2 card
Configuring a Cisco CallManager system to work with Biamp s VoIP-2 card AudiaFLEX Voice-over-IP Interface Biamp s VoIP-2 card allows Biamp AudiaFLEX digital signal processors to make and receive calls
More informationConfiguring Quadro IP PBXs with "SIP Connect"
Configuring Quadro IP PBXs with "SIP Connect" Revision: 1.0 Abstract: This document describes how to configure the Quadro IP PBXs to use the IP-PSTN service from SIP Connect PAGE 1 Document Revision History
More informationConnecting with Vonage
Connecting with Vonage Vonage (http://www.vonage.com/) offers telephone service using the VoIP (Voice over Internet Protocol) standard SIP (Session Initiation Protocol). The service allow users making
More informationBroadvox SIP Trunk Setup
DSX Broadvox SIP Trunk Setup April 22, 2011 Issue 1.05 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 DSX DSX SIP Trunk Setup Issue 1.05 Copyright 2011 NEC Corporation of America 6535 N.
More informationVocia MS-1 Voice-over-IP Interface. Avaya System Verification. Configuring Avaya Aura Session Manager system with Biamp s Vocia MS-1
Configuring Avaya Aura Session Manager system with Biamp s Vocia MS-1 Vocia MS-1 Voice-over-IP Interface The Biamp Vocia Message Server (MS-1) includes functionality to allow pages to be initiated over
More informationOpera Wireless Mobilty
Opera Wireless Mobilty How to set-up a Nokia E51 handset as a SIP WiFi extension off the Opera 4IP/20IP system This will allow your mobile phone to act as an extension when you are in the office. Your
More informationAllo PRI Gateway and Elastix Server
Allo PRI Gateway and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Allo PRI Gateway configuration. We re going to configure a SIP Trunk
More informationApplication Notes for Configuring Wesley Clover Solutions Trading Platform with Avaya IP Office using SIP Trunks Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Wesley Clover Solutions Trading Platform with Avaya IP Office using SIP Trunks Issue 1.0 Abstract These Application Notes contain
More informationConfiguring Positron s V114 as a VoIP gateway for a 3cx system
Assumptions: Configuring Positron s V114 as a VoIP gateway for a 3cx system The IP address of the V114 is 192.168.1.2 The IP address of the 3CX PBX System is 192.168.1.110 3CX already has some IP phones
More informationLink2VoIP SIP Trunk Setup
DSX Link2VoIP SIP Trunk Setup April 23, 2011 Issue 1.00 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402
More informationConnecting Sipura ATAs to a legacy PBX System.
Connecting Sipura ATAs to a legacy PBX System. The FXO port (line port) of a Sipura SPA 3000 can be connected up to an analogue extension port of a PBX system in just the same way it is connected to an
More informationHow to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions
How to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Cisco UC500 IP PBX to connect to Integra Telecom SIP Trunks.
More informationTalkswitch. SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Talkswitch 848 VS IP PBX Version 7.11.006
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Talkswitch 848 VS IP PBX Version 7.11.006 Goal The purpose of this document is to describe the steps needed to configure the Talkswitch
More informationConfiguration Notes 0215
Mediatrix Digital and Analog VoIP Gateways DNS SRV Configuration for a Redundant Server Solution (SIP) Introduction... 2 Deployment Scenario... 2 DNS SRV (RFC 2782)... 3 Microsoft Server Configuration...
More informationVoIP H.323 Series. VoIP Gatways: VoIP 422/404/440/800 VoIP Routers: VoIP 404R/440R/200R/110R. Quick Setup Guide
VoIP H.323 Series VoIP Gatways: VoIP 422/404/440/800 VoIP Routers: VoIP 404R/440R/200R/110R Quick Setup Guide Important Information In this guide, you will learn how to setup our VoIP gateway and Routers
More informationIP Office Technical Tip
IP Office Technical Tip Tip no: 188 Release Date: September 27, 2007 Region: GLOBAL Verifying IP Office SIP Trunk Operation IP Office back-to-back SIP Line testing IP Office Release 4.0 supports SIP trunking.
More informationSIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. FortiVoice Configuration 3 3.1 Global Settings 4 3.2 SIP Registration
More informationTechnical Publications
January 09 babytel ITSP Setup Author: Zultys Technical Support This document covers how to set up a babytel account. For ITSP Accounts ALG is required. For further information on ALG please refer to the
More information