Date of issue: Date of revision: - Version: 1

Transcription

1 MATERIAL SAFETY DATA SHEET Prepared according to the Decree of European Council no. 1907/2006 from regarding registering, evaluation, certification and authorizations in range of chemicals (REACH), creation of European Chemicals Agency, changing Directive 1999/45/EC and cancelling decree of Council no. 793/93 and decree of Commission no.1488/94, as well as directives 76/769/EC, 91/155/EC, 93/67/EC, 93/105/EC and 2000/21/EC. SECTION 1 IDENTIFICATION OF THE PREPARATION AND OF THE COMPANY/UNDERTAKING 1.1. Product identifier: SEA LINE EPOXY FILLER UNIVERSAL SZAPACHLÓWKA EPOKSYDOWA UNIWERSALNA 1.2. Relevant identified uses of the substance or mixture and uses advised against: Professional repairs of car body repairs Details of the supplier of the safety data sheet: Manufacturer/Distributor TROTON Sp. z. o. o Gościno Ząbrowo, 14A, Poland Tel./Fax: Tel.: troton@troton.com.pl Responsible person; troton@troton.com.pl 1.4. Emergency telephone number: (from 8:00 am 4:00 pm) SECTION 2 IDENTIFICATIN OF THREATS 2.1. Classification of the substance or mixture Classification according to Directive 67/548/EEC or Directive 1999/45/EC: Irriting (Xi) Irritating to eyes and skin (R36/38). May cause sensitization by skin contact(r43). Dangerous for the environment (N). Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment (R51/53). Classification according to Regulation (EC) No 1272/2008: Muta. 2 Skin Irrit. 2 Eye Irrit. 2 Skin Sens. 1 Aquatic Chronic 2 WARNING! H-phrases: H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H341 Suspected of causing genetic defects H411 Toxic to aquatic life with long lasting effects. P-phrases: P102 Keep out of reach of children. P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P273 Avoid release to the environment. P280 Wear protective gloves/protective clothing/eye protection/face protection. P302 + P352 IF ON SKIN: Wash with plenty of soap and water. P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P308 + P313 IF exposed or concerned: Get medical advice/attention. P405 Store locked up. P501 Dispose of contents/container according to the local regulations. FILLER 1 / 17.

2 2.2. Label elements Harmful(Xn) Dangerous for the environment(d) Risk phrases: R 36/38 - Irritating to eyes and skin. R 43 - May cause sensitisation by skin contact R 68 - Possible risk of irreversible effects. R 51/53 - Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Safety phrases: S 2 - Keep out of the reach of children S 24/25 - Avoid contact with skin and eyes. S 36/37/39 - Wear suitable protective clothing, gloves and eye/face protection. S 46 - If swallowed, seek medical advice immediately and show this container or label S 60 - This material and its container must be disposed of as hazardous waste Content: 4,4'-Isopropylidenediphenol, oligomeric reaction products with 1-chloro-2,3-epoxypropane (M < = 700) 2.3. Information concerning particular hazards for human and environment: Inhalation: in mild cases it causes cough, irritation of the mouth and throat, sometimes it causes chest pain. In more acute cases it causes headache, vertigo, fatigue, maysthenia, drowsiness and in extreme cases loss of consciousness. Eye contact: causes mechanical irritation, redness, pain and asthenopia. If the drops of the product get in the eyes, may cause impairment of sight and allergic reactions. Skin contact: may cause irritation. In case of problematic skin, skin absorption may occur. In case of long term or repeated contact the skin drying and erythroderma may occur. Irritation and redness may occur. Chronic exposure: In case of chronic inhalation of the vapour/dust of the product, chest pain, irritation of the mucous membranes, headache, vertigo, excitement or drowsiness, problems with the digestive system, exsiccation, cracking of the skin and allergy may occur. SECTION 3 COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Mixture: Classification REACH CLP Description CAS No EU No EEC No (%) Hazard R phrase Hazard cat. H phrase symbol 4,4'-Isopropylidenediphenol, oligomeric reaction products with 1-chloro-2,3-epoxypropane (M < = 700) [(tolyloxy)methyl]oxirane, cresyl glycidyl ether X <35 Xi N Muta. Cat. 3 Xi R36/38 R43 R51/53 R68 R38 R43 R51-53 Eye Irrit. 2 Skin Irrit. 2 Skin Sens. 1 Aquatic Chronic 2 Muta. 2 Skin Irrit. 2 Skin Sens. 1 Aquatic Chronic 2 N Full meaning of phrases and symbolsare in section 16. SECTION 4 FIRST AID MEASURES 4.1. Description of first aid measures: Take normal precautionary measures applied during the handling of chemicals. In case of any symptoms, seek medical advice. IN CASE OF INGESTION: Measures: - If swallowed, do not induce vomiting (risk of aspiration). - Obtain immediate medical help. H319 H315 H317 H411 H341 H315 H317 H411 FILLER 2 / 17.

3 IN CASE OF INHALATION: Measures: - Remove the affected person to fresh air, keep calm, cover with a blanket. - In case of shortness of breath, give oxygen. - If breathing has stopped, administer artificial respiration and obtain medical help. IN CASE OF SKIN CONTACT: Measures: - Immediately flush with plenty of water. - Take off all contaminated clothing. - Wash skin with plenty of water and soap. - In case of symptoms, obtain medical attention and show him the label! IN CASE OF EYE CONTACT: Measures: - Remove contact lenses. - Flush immediately with plenty of water for 15 minutes, holding the eyelids wide open. - Consult an ophthalmologist Most important symptoms and effects, both acute and delayed: Inhalation: in mild cases it causes cough, irritation of the mouth and throat, sometimes it causes chest pain. In more acute cases it causes headache, vertigo, fatigue, maysthenia, drowsiness and in extreme cases loss of consciousness. Eye contact: causes mechanical irritation, redness, pain and asthenopia. If the drops of the product get in the eyes, may cause impairment of sight and allergic reactions. Skin contact: may cause irritation. In case of problematic skin, skin absorption may occur. In case of long term or repeated contact the skin drying and erythroderma may occur. Irritation and redness may occur. Chronic exposure: In case of chronic inhalation of the vapour/dust of the product, chest pain, irritation of the mucous membranes, headache, vertigo, excitement or drowsiness, problems with the digestive system, exsiccation, cracking of the skin and allergy may occur Indication of any immediate medical attention and special treatment needed: No special antidote, apply symptomatic treatment. SECTION 5 FIRE-FIGHTING MEASURES 5.1. Extinguishing media: Suitable extinguishing media: Foam, carbon dioxide or dry chemical Unsuitable extinguishing media: Strong water jet Special hazards arising from the substance or mixture: In case of combustion, carbon oxide and toxic fumes are formed Advice for firefighters: Wear full protective clothing (gas-tight and antistatic) and self-contained breathing apparatus. Cool the fire affected containers with water spray. Prevent penetration into ground and surface water. Prevent penetration of the fire extinguishing media into ground and surface water. Collect fire extinguishing media separately, do not discharge into sewage system. SECTION 6 ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions, protective equipment and emergency procedures: For non-emergency personnel: Keep unprotected people away, allow only well trained experts wearing suitable protective clothing to abide in the field of accident For emergency responders: Remove all ignition sources, flames. Protect sewage outlets. Disperse vapours with water spray. Stop leakage close the source of the leakage, seal damaged container and place in an other container. FILLER 3 / 17.

4 Ensure adequate ventilation. Wear protective clothing and gloves. Do not inhale vapours Enivornmental precautions: Dispose of spillage and waste (product/packaging) in accordance with all applicable environmental laws. Do not allow to enter sewers/soil/surface or ground water. Notify the respective authorities in accordance with local law in the case of environmental pollution immediately Methods and material for containment and cleaning up: Absorb the spilled product with an inert substance (e.g.: sand or diatomaceous earth) and transfer into a sealed container, and send to an authorized waste disposal company. During disposal wear suitable personal protective equipment Reference to other sections: For further and detailed information see section 8 and 13. SECTION 7 HANDLING AND STORAGE 7.1. Precautions for safe handling: Observe conventional hygiene precautions. Avoid contact with skin and eyes. Do not inhale vapours. Do not eat, drink or smoke during the usage. Technical measures: Use only in well-ventilated places with exhaust ventilation. Tools, equipments and containers must be sealed tightly. Precautions against fire and explosion: Keep away from heat and ignition sources Conditions for safe storage, including any incompatibilities: Technical measures and storage condition: Keep in original, tightly closed and labelled container. The place of storage has to be properly ventilated and cleanable. Store in cool and dry place. Protect against sunlight. Store below 20 C. Do not store with self-igniting substances and peroxides. Store in original, properly labelled containers, which are tightly sealed. Do not smoke, eat, use open fire and sparking tools in the place of the storage. Keep away from the reach of children. Follow all instructions on the label. Incompatible materials: strong oxidizing agents. Packaging material: original container Specific end use(s): No specific instructions available. SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control parameters: 8.2. Exposure controls: In case of a hazardous material with no controlled concentration limit it is the employer s duty to keep concentration levels down to a minimum achievable by existing scientific and technological means, where the hazardous substance poses no harm to workers Appropriate engineering controls In pursuance of work is proper foresight needed to avoid spilling onto clothes and floors and to avoid contact with eyes and skin. The suction of the vapours at the source(s) of emission and general exhaust ventilation is required. The exhaust vents shoudl be placed in the upper part of the room and at the floor level. FILLER 4 / 17.

5 Keep away from heat and ignition sources Individual protection measures, such as personal protective equipment: 1. Eye/face protection: When working with the product, wear safety glasses with side protection (like goggles) to protect against splashes or a full face shield for protection against vapours and aerosols 2. Skin protection: a. Other: wear suitable protective clothing made of dense fabric. To prevent skin drying, use suitable protective cream. Separate private clothes from work clothes. Contaminated clothes can not be reused without prior cleaning (washing). b. Other: wear suitable protective clothing made of dense fabric. To prevent skin drying, use suitable protective cream. Separate private clothes from work clothes. Contaminated clothes can not be reused without prior cleaning (washing). 3. Respiratory protection: In case of insufficient ventilation, wear suitable respiratory protection - protective filter masks adapted to activities associated with processing of the product. 4. Thermal hazard: None known Environmental exposure controls: No specific prescription. The requirements detailed in Section 8 assume skilled work under normal conditions and usage of the product for appropriate aims. If conditions differ from normal or work is carried out under extreme conditions an expert s advice should be sought out before deciding upon further protective measures. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES: 9.1. Information on basic physical and chemical properties Physical condition/form coluour Liquid of high viscosity; white Odour Boiling point Melting point: Vapours pressure Solubility in water and other solvents In water: insoluble Solubility in organic solvents Well soluble Specific gravity ph: Ignition temperature 121 C for 4,4'-Isopropylidenediphenol, oligomeric reaction products with 1- chloro-2,3-epoxypropane M <= 700 Explosive properties: limits Autoignition point Flammable available Explosive properties: limits Not explosive, no concern Oxidizing properties Not oxidizing, no concern Distribution ratio 1-n-octanol/water available Other properties:viscosity available 9.2. Other information: No other information available. SECTION 10 STABILITY AND REACTIVITY Reactivity: None known Chemical stability: At normal temperature: stabile at general conditions of work Possibility of hazardous reactions: None known Conditions to avoid: High temperature, fire Incompatible materials: storng oxidizing agents Hazardous decomposition products: In case of high temperature or fire, carbon oxides and toxic smoke may evolve. FILLER 5 / 17.

6 SECTION 11 TOXICOLOGICAL INFORMATION Information on toxicological effects: Acute toxicity: Harmful by inhalation and in contact with skin. Irritation: None known. Corrosivity: None known. Sensitisation: None known. Repeated dose toxicity: Repeated exposure may cause skin dryness or cracking. Carcinogenicity: None known. Mutagenicity: None known. Reproduction toxicity: None known For substances subject to registration, brief summaries of the information derived from the test conducted: Relevant toxicological properties of the hazardous substances: Information on toxicological effects: Name of the substance: CAS-number: Dose: Value: Unit: 4,4'-Isopropylidenediphenol, LD 50 (rat, dermal) > 2000 mg/kg oligomeric reaction products with chloro-2,3-epoxypropane LD 50 (rat, oral) > 2000 mg/kg Information on likely routes of exposure: ingestion, inhalation, skin and eye contact Symptoms related to the physical, chemical and toxicological characteristics: Inhalation: in mild cases it causes cough, irritation of the mouth and throat, sometimes it causes chest pain. In more acute cases it causes headache, vertigo, fatigue, maysthenia, drowsiness and in extreme cases loss of consciousness. Eye contact: causes mechanical irritation, redness, pain and asthenopia. If the drops of the product get in the eyes, may cause impairment of sight and allergic reactions. Skin contact: may cause irritation. In case of problematic skin, skin absorption may occur. In case of long term or repeated contact the skin drying and erythroderma may occur. Irritation and redness may occur. Chronic exposure: In case of chronic inhalation of the vapour/dust of the product, chest pain, irritation of the mucous membranes, headache, vertigo, excitement or drowsiness, problems with the digestive system, exsiccation, cracking of the skin and allergy may occur Delayed and immediate effects as well as chronic effects from short and long-term exposure: Harmful by inhalation and in contact with skin. Repeated exposure may cause skin dryness or cracking Interactive effects: Absence of specific data: No information Other information: SECTION 12 ECOLOGICAL INFORMATION Toxicity: Aquatic toxicity: Name of the substance: CASnumber: Method: Value: Unit: Toxicity to aquatic organisms LC50/EC50/IC mg/l 4,4'-Isopropylidenediphenol, LC50 daphnia(daphnia magna) 3,3 mg/l oligomeric reaction products According to the OECD guidelines regarding the testing the substance, it is with 1-chloro-2,3- not considered as readily biodegradable. epoxypropane Bioconcentration potential is low (BCF less than 100 or log Pow less than 3) Effect on activated sludge: at proper entering of small concentrations to biological sewage treatment plants no perturbations should be expected during the decomposition of the activated sludge Persistence and degradability: FILLER 6 / 17.

7 12.3. Bioaccumulation potential: Mobility in soil: Results of PBT and vpvb assessment: Other adverse effects: SECTION 13 DISPOSAL CONSIDERATIONS Waste treatment methods: Disposal according to the local regulations Information regarding the disposal of the product: Do not dispose with communal wastes, do not pour into drainage system. Incinerate in specially adapted installations or deliver to authorized waste collector. European Waste Catalogue code: wastes from MFSU and removal of paint and varnish * waste paint and varnish containing organic solvents or other dangerous substances * hazardous waste Information regarding the disposal of the packaging Used packaging should be delivered to authorized collector who has due permission within the range of waste management and especially in dangerous waste management. European Waste Catalogue code: For used packaging: * packaging containing residues of or contaminated by dangerous substances * hazardous waste Physical/chemical properties that may affect waste treatment options shall be specified: None known Sewage disposal: None known Special precautions for any recommended waste treatment: SECTION 14 TRANSPORT INFORMATION Land transport (ADR/RID) UN Number UN 3077 UN proper shipping name UN 3077 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S (epoxy resin) Transport hazard class(es) 9 Label: 9 Hazard identification number: 90 Packing group III Enviromental hazards Yes, see of ADR Agreement Tunel resticion code (E) Marine transport IMDG/IMO UN Number UN 3077 UN proper shipping name Transport hazard class(es) 9 Label: 9 UN 3077 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S (epoxy resin) FILLER 7 / 17.

8 Hazard identification number: 90 EmS code F-A, S-F Packing group III Enviromental hazards YES IMDG Code Air transport IATA UN Number UN 3077 UN proper shipping name UN 3077 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S (epoxy resin) Transport hazard class(es) 9 Label: 9 Hazard identification number: 90 Packing group III Enviromental hazards YES IATA Dengerous Goods Regulation Special precautions for user 8L SECTION 15 REGULATORY INFORMATION Safety, health and environmental regulations/legislation specific for the substance or mixture: REGULATION (EC) No 1907/2006 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 18 December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH), establishing a European Chemicals Agency, amending Directive 1999/45/EC and repealing Council Regulation (EEC) No 793/93 and Commission Regulation (EC) No 1488/94 as well as Council Directive 76/769/EEC and Commission Directives 91/155/EEC, 93/67/EEC, 93/105/EC and 2000/21/EC COMMISSION REGULATION (EC) No 790/2009 of 10 August 2009 amending, for the purposes of its adaptation to technical and scientific progress, Regulation (EC) No 1272/2008 of the European Parliament and of the Council on classification, labelling and packaging of substances and mixtures DIRECTIVE 1999/45/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 31 May 1999 concerning the approximation of the laws, regulations and administrative provisions of the Member States relating to the classification, packaging and labelling of dangerous preparations REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 December 2008 on classification, labelling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006 COMMISSION REGULATION (EU) No 453/2010 of 20 May 2010 amending Regulation (EC) No 1907/2006 of the European Parliament and of the Council on the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) Chemical safety assessment: - SECTION 16 OTHER INFORMATION Information regarding the revision of the safety data sheet: - Full text of the abbreviations in the safety data sheet: DNEL: Derived no effect level. PNEC: Predicted no effect concentration. CMR effects: carcinogenity, mutagenicity and toxicity for reproduction: PBT: Persistent, bioaccumulative and toxic.. n.d.: not defined.. n.a.: Not applicable.. Data sources: - Relevant R-Phrases (number and full text) of Section 2 and 3: R 36/38 - Irritating to eyes and skin. R38 - Irritating to skin. R 43 - May cause sensitisation by skin contact R 68 - Possible risk of irreversible effects. R 51/53 - Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Relevant H-Phrases (number and full text) of Section 2 and 3: FILLER 8 / 17.

9 H302 - Harmful if swallowed H315 Causes skin irritation. H319 Causes serious eye irritation. H317 May cause an allergic skin reaction. H341 Suspected of causing genetic defects H411 Toxic to aquatic life with long lasting effects. EUH 205 Contains epoxy constituents. May produce an allergic reaction. Abbreviations of the hazard categories: Eye Irrit. Eye irritation Skin Irrit. Skin irritation Aquatic Chronic - Aquatic Chronic Skin sens. Skin sensitization Mutagen. - Mutagenicity Training instructions: - Recommended restrictions on use (non-statutory recommendations by supplier): - This safety data sheet had been prepared on the basis of information provided by the manufacturer. The information, data and recommendations contained herein are provided in good faith, obtained from reliable sources and believed to be true and accurate as of the date issued; however, no representation is made as to the comprehensiveness of the information. The MSDS shall be used only as a guide for handling the product; in the course of handling and using the product other considerations may arise or be required. Since the conditions or the handling, the storage and the disposal of this product are beyond the control of the manufacturer, the distributor or the preparer of this SDS, no warranty, expressed or implied, regarding the product described in this MSDS shall be created or inferred by any statement in this SDS. No responsibility is assumed regarding the accuracy, completeness or suitability of all or any of the information contained herein or the results to be obtained from the use thereof at the time of use. In no way shall the manufacturer, the distributor or the preparer of the be liable for any claims, losses or damages of third parties, personal injury, property damage, lost profits or any special, direct, indirect, incidental, consequential or exemplary damages resulting from the use of or reliance upon such information. Users are cautioned to determine the appropriateness and applicability of the above information to their particular circumstances and purposes and assume all risk associated with the use of this product. It is the responsibility of the user to fully comply with local, national and international regulations concerning the use of this product. FILLER 9 / 17.

10 1 IDENTIFICATION OF PREPARATION IDENTIFICATION OF MANUFACTURER AND DISTRIBUTOR Identification of Preparation: SEA LINE EPOXY FILLER UNIVERSAL - HARDENER SZAPACHLÓWKA EPOKSYDOWA UNIWERSALNA - UTWARDZACZ Application: Materials for boat-building and repair. Manufacturer/Distributor: TROTON Sp. z o. o. tel/fax Gościno tel Ząbrowo 14A, Poland troton@troton.com.pl Emergency telephone number (8:00 am 4:00 pm): Person is responsible for making this Safety Material Data Sheet: Katarzyna Romanska k.romanska@troton.com.pl Date of preparation: January10 th, 2009 Revision date May 20 th, IDENTYFICATION OF THREATS 2.1 Classification and marking of preparation Product harmful to environment (N). Corrosive product (C). Harmful by inhalation, in contact with skin and if swallowed (R 20/21/22) Causes burns (R 34) Possible risk of impaired fertility (R 62) Possible risk of harm to the unborn child (R 63) Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment (R 50/53) May cause sensitization by skin contact (R43). Product causes dermal irritation. Substances in this product may effect the central nervous system. Product contains highly abrasive substances. Product contains nonylophenol. May cause allergic reactions. Inhalation: May cause irritation to the upper respiratory system. May damage lungs, throat, nostrils. May cause burns on skin, eyes, and respiratory system. May effect the central nervous system, with the following symptoms: headache, disorientation, dizziness, difficulty breathing. Longt-erm exposure may lead to suffocation. Long-term inhalation of vapours/aerosols may irritate the respiratory system. Lead the injured person to fresh air, ensure calm, cover with a blanket. If the injured person is not breathing, induce breathing artificially. Seek medical attention immediately. Contact with eyes: Substances in this product cause irritation to the eyes. Direct contact may cause retinal damage and visual impairment in the form of "black patches" and "fog". FILLER 10 / 17.

11 Contact with Skin: Swallowing: Related Illnesses: Internal Organds: Symptoms: When emerging into bright light, a "halo"might be seen around light sources (loss of focus). Long-term exposure may lead to blindness. May cause serious skin irritation. Heavy burns may lead to shock of the central nervous system, resulting in headaches, dizziness, and difficulty breathing. Product harmful if swallowed. If swallowed, burns result in the mouth, lips, throat, and stomach. Burns may lead to shock of the central nervous system, resulting in headache, disorientation, vomiting, stomachaches, dizziness, difficulty breathing. Long-term ingestion causes death. Asthma. Visual Impairment. Dermal allergies. Neurological disorders. Effects respiratory system, skin, eyes, central nervous system. Repeated or long-term exposure to low concentrations may cause a sore throat. 3 CHEMICAL COMPOSITION AND INFORMATION CONCERNING INGREDIENTS 3.1 Dangerous ingredients of the mixture and their classification Compound: EEC No. CAS No. WE No. % by Symbol R Phrases weight 4-tert-butylphenol Xi; N 38-50/53 nonylphenol C; N m-phenylenebis (methylamine) C; Xn trimethylhexane-1,6- diamine 50/ / / C; N /53 Full definitions of terms prefixed by R are given in point 16 of the information card. 4 FIRST AID MEASURES 4.3 Environmental Hazards Product has negative effects on water-borne organisms, and may cause long-term environmental damage to aquatic environments. Inhalation: Contact with eyes: Contact with skin: Swallowing: Lead the injured person to fresh air, ensure calm, cover with a blanket. If the injured person is not breathing, induce breathing artificially. Seek medical attention immediately. Remove contact lenses. Wash eyes with large amount of water for 15 minutes, with the eyes held wide open. See an optometrist. Immediately rinse with a large amount of water, remove all contaminated clothing, wash skin with a large amount of water. If medical assistance is unavailable, continue washing skin for at least one hour. Cover the wound with sterile gauze. If irritation continues, seek medical attention immediately. Application of corticosteroid cream increases dermal injuries. If product is swalloed, do not induce vomiting, as there is a risk of choking and introducting the product to the lungs. Do not drink. Seek medical attention immediately. FILLER 11 / 17.

12 General Cautions: Follow all usual precautions for working with hazardous chemicals. If any troubling signs appear, seek medical attention. Directions for doctors: lack of specific antidote - treat symptoms as they occur 5 PROCEEDING IN CASE OF FIRE 5.1 Recommended extinguishing media Foam, carbon dioxide or dry chemicals. Keep tanks exposed to fire cool by continuous spraying with water. 5.2 Prohibited extinguishing media Strong water jets. 5.3 Hazardous decomposition products Ammonia vapours may form, containing toxic nitric oxides. The use of water to extinguish flames may lead to the creation of toxic aerosols. Incomplete burning causes the formation of carbon monoxide. Ammonia vapors may be released at high temperatures. Incomplete burning may release nitrogen oxides.(nox) 5.4 Special fire-fighting equipment Gas-tight anti-electrostatic suit, fully protecting the respiratory system. Do not allow flame-retardant materials to contaminate groundwater or surface water. Flame-retardant materials should be kept separately, and must not be poured into drains. 5.5 Hazardous Materials Sodium perchlorate, organic acids, mineral acids. Product may damage surfaces made from aluminium, zinc, and sheet metal. May react violently or even explode in contact with peroxide. CAUTION! N-nitrosoamine may form if the product comes into contact with nitric acid, nitrites, or air with a high content of nitric oxide 6 PROCEEDING IN CASE OF UNINTENTIONAL RELEASE TO ENVIRONMENT 6.1 Protection of humans Precautionary measures: Remove all sources of ignition, extinguish flames, protect sewage outlets, dilute vapours with water spray. Remove leakage close fluid inlet, seal damaged container and place in a substitute container. Secure adequate ventilation. Wear protective clothing and gloves. Do not inhale vapours. 6.2 Protection of environment Prevent penetration into sewage system, soil, underground and surface water. In case the product penetrates into sewage system or water, notify applicable authorities immediately. 6.3 Methods of neutralisation, collection and environment cleaning Absorb spilled product with chemically neutral absorbing material (sand, diatomaceous earth), transfer to tight containers and deliver to authorised disposal agent. 7 HANDLING PREPARATION AND STORE CONDITIONS 7.1 Handling precautionary measures Use only in thoroughly ventilated locations with exhaust ventilation. Keep away from heat and sources of ignition. It is recommended to take precautionary measures to avoid skin and eye contact. Do not inhale vapours. Plants, armatures and tanks must be always sealed tightly. Do not eat, drink or smoke when using. 7.2 Storage FILLER 12 / 17.

13 Protect against sunlight, store at temperature below 20 o C. Keep in cool, dry and well-ventilated location. Keep away from the reach of children. Do not store with self-igniting substances and peroxides. Store in original, properly identified containers, tightly sealed. Do not smoke, eat, use open fire and sparking tools in a storehouse. 8 EXPOSURE CONTROL AND MEASURES OF INDIVIDUAL PROTECTION 8.1 Exposure limitation technical measures Spot ventilation exhausting vapours from emission places and general ventilation required. Suction vents of spot ventilation at the working level or below. Exhaust vents of general ventilation in the upper part of a room and at the floor level. Do not use close to sources of heat and ignition. 8.2 Values of NDS 1, NDSCh 2, NDSP 3 Compone CAS nt No. Fenylometanol Standard Value Unit NDS 20 mg/m 3 NDSCh --- mg/m 3 Legal basis: Order of Minister of Labor and Social Policy of November 29 th, 2002 on behalf of concentrations and intensity of harmful factors in working environment (Law Gazette, No. 217, item 1833, 2002 with later amendments). 8.3 Personal protection Respiratory protection: Hands and skin: Eyes if exposure is likely to exceed the occupational exposure use approved respiratory protective equipment. impervious gloves and protective clothing. protective goggles. 9 PHYSICAL & CHEMICAL PROPERTIES 9.1 Physical condition/form coluour smell: high viscosity liquide; green ; typical of solvents. 9.2 Boiling point: 230ºC 9.3 Melting point: Vapours pressure: Solubility in water and other solvents: Solubility in organic solvents: Specific gravity: ph: Ignition temperature: >93,33ºC 9.10 Explosive properties: limits : not data available 9.11 Autoignition point: Flammable: high viscosity liquid, 9.13 Explosive properties: limits : not explosive,not concern 9.14 Oxidizing properties: not oxidizing,not concern 1 NDS The Maximum Permissible Concentration 2 NDSCh -The Maximum Permissible Momentary Concentration the average value of concentration which should not result the negative changes of worker s health, if exists in work environment not longer than 15 minutes and not more frequently than two times per working shift in time interwal not shorter than one hour. 3 NDSP - The Maximum Permissible Threshold Value of concentration, which, due to threat for worker s health or life can not be exceeded in working environment in any moment. FILLER 13 / 17.

14 9.15 Distribution ratio 1-n-octanol/water: not data available 9.16 Other properties: - 10 STABILITY AND REACTIVITY The product is stable if handled and stored according to handling and storage directions Conditions to be avoided(which cause dangerous reactions): High temperature,fire Substances cause dangerous: Strong oxidants Dangerous products of disintegration: In condition of high temperature and fire can arise carbon oxides and toxical smokes. 11 TOXICOLOGICAL INFORMATION 11.1 Health results in case of acute exposition Toxicological data Component CAS No. Dose: Value: Unit nonylphenol LD50 (rat, oral) 580 mg/kg LD50(rabbit, skin) 2,033 mg.kg 4-tert-butylphenol LD50 (rat, oral) 1,750 mg/kg LD50 (rat, dermal) >2,0 mg/kg LD50 (rat, inhalation) --- mg/l/6h 11.2 Health results in case of chronic exposition Persons, who are chronically exposed to risk of breathing the air contaminated by vapors or dust originated from this preparation, may complain for irritation of mucous membrane, headaches and vertigousness, excitement or drowsiness, problems with alimentary system, exsiccation, skin fissuring and allergies Health results in case of local exposition Breathing: in mild cases there appears the cough, irritations of mouth and throat, sometimes the pain of chest. In more acute cases - headache and vertigousness, fatigue feeling, myasthenia, drowsiness and in exceptional cases the black-out. Eye contact: preparation acts gratingly on eyes, causing their redness, pain and asthenopia. If drops of products get in eyes, they may cause the impairment of sight and allergic reactions. Skin contact: preparation may cause the irritation. In case of impaired skin there may happen the sorption to blood. Long or repeated contact of preparation with skin may result in its drying-up and erythroderma. Irritations and redness may also happen. 12 ENVIRONMENTAL INFORMATION Not data available about mobility in envitonment, biodegradation and bioacumulation of product Observe of product in environment. Protect against penetrates into sewage system or water. Component CAS No. Dose: Value: Unit LC50(96h)-fish 0,128 mg/l nonylphenol EC50(48h)- (Daphnia manga) 0,0840,100,19 mg/l FILLER 14 / 17.

15 EC50(48h) (Daphnia manga) mg/l 13 HADLING WITH WASTES The way of excess amount removal or waste disposal Do not dispose with communal wastes; do not pour to drainage system. Burn in specially adapted installations or deliver to authorized waste collector Post production, preparation, handling and post use waste, lacquer and paint disposal * Lacquer and paint waste, containing organic solvents or another dangerous substances dangerous waste. The way of used packing disposal Code of waste: * Packing containing residues of dangerous substances or packing contaminated with dangerous substances. Used packing should be delivered to authorized collector who has due permission within the range of waste management and especially in dangerous waste management. Legal basis: Act, dated April 27 th, 2001 about wastes (Law Gazette, No. 62, item 628, 2001); Order of Minister of Environment, dated September 27 th, 2001, on behalf of catalog of wastes (Law Gazette No. 112, item 1206, dated October 8 th, 2001); Act, dated May 11 th, 2001on behalf of packing and pack wastes (Law Gazette No. 63, item 638, 2001); Act, dated December 19 th, 2002 on behalf of changes of act about wastes and changes in other acts (Law Gazette No. 7, item 78, 2003); Act, dated July 29 th, 2005 on behalf of changes of act about wastes and changes in other acts (Law Gazette No. 175, item 1458, 2005) 14 INFORMATION ABOUT TRANSPORT Road and railway transport: ADR/RID: UN 3263 Class: 8 Packing group: II 15 INFORMATION CONCERNING THE LAW REGULATIONS FILLER 15 / 17.

16 15.1 Packages Packages marking: Sticker containing: SEA LINE HARDENER TO PUTTY EPOXY ultralekka Copm. B MARKING C N IRRITANT HARMFUL TO ENVIRONMENT Phrases indicating thread type: Phrases indicating conditions of safe use: R 35 Causes severe burns R 38 Irritating to skin R 43 May cause sensitization by skin contact R 51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment R 62 Possible risk of impaired fertility R 63 Possible risk of harm to the unborn child S 2 Keep out of the reach of children S 24 Avoid contact with the skin S 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice S 36/37/39 Wear suitable protective clothing, gloves and eye/face protection S 45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) S 60 This material and its container must be disposed of as hazardous waste. Contains: nonylphenol ( 0,1%); 4-tert-butylphenol; trimethylhexane-1,6-diamine 15.2 Other regulations, if apply: o Act on behalf of substances and chemical preparations, dated January 11 th, 2001 (Law Gazette No. 11, item 84; No. 100, item 1085; No. 123, item 1350; No. 127, item 1367 with amendment, dated July 5 th, 2002 (Law Gazette No. 142, item 1187); o Order of Minister of Health, dated July 3 rd, 2002 on behalf of Sheet of characteristic of dangerous substance and dangerous preparation (Law Gazette No. 140, item 1171); o Order of Minister of Health, dated December 14 th, 2004 which changes the order on behalf of Sheet of characteristic of dangerous substance and dangerous preparation (Law Gazette No. 2, item 8); o Order of Minister of Health, dated September 28 th, 2005 on behalf of list of dangerous substances with their classification and marking (Law Gazette No. 201, item 1674); FILLER 16 / 17.

17 o o o o o o o Order of Minister of Health, dated September 2 nd, 2003 on behalf of markings on packing of dangerous substances and chemical preparations (Law Gazette No. 173, item 1679 with later amendments); Order of Minister of Health, dated September 2 nd, 2003 on behalf of criteria and methods of classification of substances and chemical preparations (Law Gazette No. 171, item 1666 with later amendments); Act, dated April 27 th, 2001 about waste (Law Gazette No 62, item 628) and Order of Minister of Environment, dated September 27 th, 2001 on behalf of catalog of waste (Law Gazette No. 112, item 1209); Act, dated July 29 th, 2005 on behalf of changes of Act about wastes and about the changes of some other acts (Law Gazette No. 175, item 1458, 2005); Order of Minister of Labor and Social Policy, dated November 29tt, 2002 on behalf of maximum permissible concentrations and intensity of harmful factors in work environment (Law Gazette No 217, item 1833, 2002 with later amendments). Ordinance of Minister for Labour and Social Policy of 29 th November 2002 in the Matter of Admissible Concentrations and Intensity of Factors Harmful for Health in Workplace Environment (Official Journal No 217 Pos. 1833, 2002 with subsequent modifications) Ordinance of Minister for Economy of 16 th January In the Matter of Detailed Requirements for Limitation of Emission of Volatile Organic Compounds due to the use of Organic Solvents in Certain Paints and Varnishes and Vehicle Refinishing Products. 72) 16 OTHER INFORMATION The purpose of information stated in this sheet is to describe the product only from the point of view of work safety requirements. User of this product bears the responsibility for making conditions of safe application of product and he is solely responsible for results of improper use of this product. R phrases (indicating type of threat) used in Section 2 of Characteristic Sheet): R 20/21 Harmful by inhalation and in contact with skin R 22 Harmful if swallowed R 34 Causes burns R 35 Causes severe burns R 48 Danger of serious damage to health by prolonged exposure R 43 May cause sensitization by skin contact R 50/53 Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment R 52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment R 62 Possible risk of impaired fertility R 63 Possible risk of harm to the unborn child FILLER 17 / 17.