LINE0 autonomous tests by local loggers
|
|
- Dominick Harvey
- 8 years ago
- Views:
Transcription
1 E.Heine Page 1 of 11 Ref : -LCM-18-1A Date : /1/5 LINE autonomous tests version 8 e.heine Objectives: Test a cable (EMC) sample in a real situation. Test the water tightness of the containers Both tests can be performed with or without a connection to the shore. In this paper a solution is presented for an offline test independent of a shore connection. Contents: Overview 1 Logger Install Software Program Logger Readout logger Leakage detection 5 Placing leak detector 6 Leakage detection readout 7 Wiring suggestion 8 Optical power recording 9 Optical power readout 1 Wiring suggestion 1 Actual general wiring schemes 11 Two tests are provided; A leak detector to check water ingress of a container and a cable break. An optical fiber test to check attenuation changing's. The testplan envisages two deployments. The first to see of the deployment procedure is correct by deployment, recovery, back to shore and check all the tinytags. The second to test the cable during several months in the water in situ. There are tests foreseen which need a connection to shore. The here presented tests don t need such a connection. With no connection to shore recovery, reading data and deployment again several times is possible. Tests procedure is as follows; Program the tinytags for the first deployment After recovery of the LINE read all tinytags and program again for the second deployment. After final recovery (after -6mnths) read all the tinytags Send all tiny tags back to K POBox DB Amsterdam 1
2 Page of 11 Ref : -LCM-18-1A Date : /1/5 LINE autonomous tests by local loggers E.Heine Local logger System based on gemini tinytag logger RS connection Sensor system powe by 1V Green status LED Red alarm LED K HEF LINE measurement items / electronic department -1-5 Logger Both tests are based on small logger system, tinytags: representative in The Netherlands; INTAB Benelux (info@intab.nl) Each logger is provided with 8 1.5V batteries (type AA) to achieve a 1V power supply with a charge of.7ah. The system is designed to meet this specification with a use of 6mnth. maximum. The power supply is 8 sec. active for each measurement. NOTE: Whenever the logger is linked to the host computer, the power supply is active. Logger specification overview; Range: -mv maximum input:: 5mV Input impedance:>1 MOhms Resolution:.8mV Accuracy: ±1mV ±.5% of reading Memory Size: 16k (non-volatile) No. of readings: 159 (approx) resolution: 8 bit Delayed start options. -A green status led what will flash: waiting delayed start: flashes every sec. logging: 1 flash (msec) every sec. storing a reading: 1 bright flash (6msec). power up: on for several seconds. Flash current = 6mA For a mission-time of 6 weeks the battery charge will be 5.7 mah for status and with an interval of min..15 mah for store data signal. - alarm led, The logger has two programmable alarms. Both are programmable for: alarm trip point, over or under voltage, latching or not latching, one or two flashes. If both alarms are trigge the LED flashes times. The alarms can be clea and set on/off via the Windows software. My suggestions would be not to use this option to spare the batteries. When the unit stops logging, the LED gives one bright, half second flash. The LED is not normally used at any other time, however if both LED s flash brightly and rapidly together, the unit will not work. Remove and refit the battery. If the problem persists, return the unit for repair. If this will disturb the PMT's in the OM then we have to blind it with adhesive tape. Battery: Alkaline-Manganese Dioxyde PC15 Duracell procell. K HEF POBox DB Amsterdam
3 E.Heine Page of 11 Ref : -LCM-18-1A Date : /1/5 Software After installing the software: 1. Establish the connection with the Tiny tag. Program the tiny logger after stop Withdraw the data after deployment: 1. Established the connection with the Tiny tag. Start off load the data. Store data in a file. Reprogram the tiny logger if necessary LINE measurement items / electronic department -1-5 SOFTWARE to read the TPG-1 recorders Type: Gemini Data Loggers, TinyTag TGPR-1, delive by INTAB Benelux. 1 SYSTEM REQUIREMENTS The minimum system requi is a 86 PC with 8MB of memory, at least 8MB of hard disk space and an SVGA monitor. Higher specification of PC is recommended as the increase in performance will be significant. Microsoft Windows version.11, 95, 98, NT Windows or XP is requi. In order to connect a logger to the PC you will need a spare serial port (9 way D-type connector) and the correct interface cable to connect between the serial port and your data logger. INSTALLATION To install the application first quit all other applications, run SETUP from Windows. The setup procedure may take a few minutes. Open TinyLoggerFlop1 Run: SETUP.EXE Use TinyLoggerFlop for the second part installation. After this installation to make an upgrade install: engupg.exe REMARKS During connected with the PC, measurements will be continuous. Off line, the 1V power is delive ca. 8 sec. before reading the measu value. Approximate 159 readings. 8 bit resolution. PROGRAMMING No alarm settings are programmed to prevent energy. Logging interval for max. 6mnth deployment will be min. at least. POBox DB Amsterdam
4 E.Heine Page of 11 Ref : -LCM-18-1A Date : /1/5 Programming and offload data LINE measurement items / electronic department -1-5 Programming For the first deployment; Program the tinytags with a delay (max. 5 days) before the deployment (period 15--5/15--5) and an interval of 5 minutes (keep the used charge below 1mAh and the number of records below 159). min interval gives 15 records and 5mAh charge is used. The first deployment takes one day in a period of weeks. Readout after a recovery; Make connection with the tinytag. Offload the data (15 records takes 5.5minutes on a Pentium ) Check the graphic presentation for calamities Store the numeric data as.txt file to work out later on shore Reprogram the tinytags without any delay and an interval of minutes (to keep the used charge below 1mAh in fact 5mAh and the number of records below 159 in fact 11) POBox DB Amsterdam
5 E.Heine Page 5 of 11 Ref : -LCM-18-1A Date : /1/5 Indication number on bottom PBS V V5 <mv brown V Leakage detection gnd 1 Rx Tx 1M k BAT17 5 DB9 (on PC) 5 RS only on OM-connector 6 fingers both sides 1mm spacing finger length mm 1k PBS 9.6. OM Cable EMC LCM+1 OM-LCM LCM to LCM-1 6 systems lend by lend by LCM installed at integration Put tinytag indication number and LCM in a database! LINE measurement items / electronic department Leakage detection for the LINE operation. sensors (each container 1). recorders ( TGPL1) with output modulator PCB. Suggestion; Place recorder + modulator in an Optical module, place sensor in a container of an other floor. In this case a EMC break will be detected also. Glue the leak detector PCB with silicon adhesive sealent or double sided adhesive tape to the bottom flange. The leak sensor can used as level indicator too by placing it vertical with the resistor at top. mission time 6wks interval meass/h Vsupply 1V Rserial 1 MOhm Rsensor 1 kohm Rloadmin..kOhm mess. dry sensor ~15mV mess. shorted sensor or cable 6mV mess. open sensor cable mv current during measurement 11.8 µa charge during mission time (6 weeks) number of records 11 Skottky diode as input limiter (BAT17, SMD SOT). At 1µA max. voltage < 5mV. 5 µah BAT17 POBox DB Amsterdam 5
6 E.Heine Page 6 of 11 Ref : -LCM-18-1A Date : /1/5 Placing leak detector mm 5 M 9 degrees 8 mm 8 mm 7 mm Bottom end cap - version D ref.: -LCM-1--A, OM / 1 CTD leakge sensor added (ref: E.Heine), glued to the bottem ( possibilities) LINE measurement items / electronic department The leak detector PCB can be glued to the bottom by silicon adhesive sealent, mastic, or double adhesive glue tape. Self adhesive cable tie mounting bases can be used as cable stress relieve if necessary. The leak detector PCB is gold plated to prevent chemical corrosion processes. mm The other PCB, the modulator, will be glued on the tinytag box together with self adhesive cable tie mounting bases. mm Leak detector PCB Test run: 5 testrun open connection modulator-detector value (mv) 15 1 dry 5 leak 1:16:19 1:19:1 1::5 1::58 1:7:5 1:: 1::6 1:6:9 1:9: 1::1 time shorted connection modulator-detector POBox DB Amsterdam 6
7 E.Heine Page 7 of 11 Ref : -LCM-18-1A Date : /1/5 1V V5 <mv brown V Leakage detection readout gnd 1 Rx Tx 1M k BAT17 5 RS only on OM-connector OM-LCM cable 1k In situ 1V V5 <mv brown V gnd 1 Rx Tx 1M k BAT17 5 DB9 5 COM PC Read out cable 1k In xlcm To test, To program To readout In OM LINE measurement items / electronic department Install issues for the leakage detector The tinytag and the modulator PCB are installed in the OM-. The 5 output wires (RS+sensor) are connected to the connector of the OM. Suggestion; Place recorder + modulator in an Optical module, place sensor in a container of an other floor. In this case a EMC break will be detected also and a sensor can be placed in the SPM/SCM while the recorder is placed in an OM of the first floor. Besides this advantage there will always a measurement over a waterblock, while in the flooded sector the measurements are demolished by the water ingress. The RS signals are connected by the OM-LCM cable to the container too. Water ingress in the container can harm the recorder by shorting these signals (has to be tested). To test, program or readout the recorder the OM-LCM cable has to be replaced or extended by a readout cable to the PC. If, in that case, the open wires of the sensor are terminated with a resistor (f.i. 1kOhm) then an actual test value can be measu instead of the open (mv) value for test purposes. In the actual situation the leakage detector is on the same floor as the tinytag in the optical module. To sense the copper wires of the EMC one pair of wires is connected to a dedicated tinytag on floor. Mnemonic Seawater: 5g salt/liter POBox DB Amsterdam 7
8 E.Heine Page 8 of 11 Ref : -LCM-18-1A Date : /1/5 Wiring suggestion Alternative scheme for LINE tests LCM OM1 OM OM fibres wires floor 5 1 Wiring suggestion scheme for LINE tests LCM OM1 OM OM fibres wires floor floor floor floor 1 floor 5 1 floor floor floor floor 1 floor floor floor 19 floor floor 18 floor 17 floor 1 SCM 1 SPM T1 T T T1 T T OTDR measurement from shore current from shore floor 16 Container with optical power logging Sphere with tinytag for leakage detection Leakage detector floor 15 floor 1 LINE measurement items / electronic department floor 1 floor 1 floor 11 floor 1 floor 9 floor 8 floor 7 floor 6 floor 5 floor floor floor floor 1 SCM 1 SPM T1 T T T1 T T OTDR measurement from shore TLS: leakage WES: Weighted 8kg adventages; WTS: Weighted kg always a leakage measurement over a water block OMS: Optical module no RS problems by one flooded container 1 container with Genova PC no extra electrical test needed container with optical monitor full place resolution by copper wire break container with k8ohm resistor container all containers will have a leakage monitor current from shore POBox DB Amsterdam 8
9 E.Heine Page 9 of 11 Ref : -LCM-18-1A Date : /1/5 PBS 9..1 Indication number on bottom 1V V5 <mv brown V Optical power recording gnd Rx Tx Optical system RS only on OM-connector 9%=.dB PBS 9.. installed at integration Put tinytag indication number and cable TUBE in a database! 5. EMC between xlcm splice test run SCM. no stress systems lend by output (mv) stress added 5.. 1:1: 1:19:1 1:6: 1:: 6 1:: 8 break added 1:8: time (min. interval) 1:55:1 11:: 11:9: 6 LINE measurement items / electronic department Optical power recording for the LINE operation. A number of fibres in each tube ( tubes of 7 fibres) of the EMC are set in series. So of these systems are placed in an xlcm container. The RS connection of the is connected to an optical module connector to be able to communicate, after installation and closed containers, with the recorder. Optical part delive by BAAS / ingenieursbureau Coenecoop. mission time 6wks interval meass/h Vsupply 1V meas. no stressed fibre 19mV relative resolution.db / 9% voltage variation meas. break 6mV current during measurement 15mA av, ma pk charge during mission time (interval min) mah number of records (interval min) Initial measurement status: Laser output = uw Pin diode (PD) sensitivity = 1A/W = 1µA/µW measu over 7Ω, if µw reach the PD then µa and 7Ohm delive 188mV to the recorder. This is confirmed by the test sheets.. measurement in situ: Two EMC fibres are connected in each floor to the next piece of EMC; 6 floors 5 splices plus 1 to connect the optical module + in the optical module to go from plastic fibre to glass, gives 55 splices. A good splice gives.1-.db attenuation;. db worst case: 55*.=1.65dB. 1km fibre will gives.db. Estimated attenuation after integration will be < 1.85dB. 1^(-1.85/1) leaves 65.% input to the APD = 6µW. 6µW on the PD gives 6µA through 7Ω and gives 1mV to the recorder.. Resolution; The recorder input maximum is mv measu with 8 bits, so LSB=/56=.78mV..78mV correspond with 1.65µW input. POBox DB Amsterdam 9
10 E.Heine Page 1 of 11 Ref : -LCM-18-1A Date : /1/5 Indication number on bottom Indication number on bottom brown 1V V5 <mv V 1V V5 <mv brown V Optical power readout gnd Rx Tx Optical system gnd Rx Tx Optical system RS only on OM-connector DB9 5 COM Read out cable PC To test, To program To readout In situ In xlcm LINE measurement items / electronic department Install issues for the optical power detector The tinytag with optical box are placed in a xlcm-container. The RS wires are connected to an OM connector to program, test or readout the recorder. If there is water ingress the recorder and box will lost. To achieve a minimum of data loss in that case, the fibres in the tubes in the EMC are proposed to be connected by the showed scheme. xlcm xlcm Top xlcm Waterblock in EMC Tube 1 Tube Tube Waterblock in EMC xlcm Bottom xlcm EMC In the actual situation a pair of fibres in the same tube is used. Mnemonic db s versus logger output Vl; Power ratio: L=1log(P 1 /P ) db, P =P 1 /(1 L/1 )=P1.1 -L/1 Pindiode characteristic: 1 A/W Measu over: 7Ω Vl=7. P 1.1 -L/1, L=1log(Vl/(7*P 1 )) P 1 is ca. µw conform the testreports. Vl (mv) L P1=µW eff % % % % % % % % % % % % % % % % % % % POBox DB Amsterdam 1
11 E.Heine Page 11 of 11 Ref : -LCM-18-1A Date : /1/5 Actual wire scheme read out: RS RS Sensor RS Leakage LCM sensor Container -1, 1-15, 17-,,, 5 read out: *RS RS Sensor 1 RS RS reading optical power meter EMC Leakage sensor LCM Container 11,16, 1 RS Sensor RS Sensor read out: *RS RS Sensor 1 RS RS Leakage sensor LCM Container 1 read out: *RS 1 Electrical load RS RS Leakage sensor LCM Container 1m Base of line EMC RS Sensor Leakage sensor SCM Container LINE measurement items / electronic department Tynytag Number Connector Connector 1 Connector Module RS Tx ( ) -1, 1-15, 17-,,, 5 RS Rx ( ) RS GND ( ) 1 1 RS Tx ( 1) 5 1, 11, 16, 1, RS Rx ( 1) 6 RS GND ( 1) 1 Leakage sensor -1, 1-15, 17-,,, 5 Leakage sensor 5 Leakage sensor ground 8 Leakage sensor 1, Leakage sensor 5 Leakage sensor ground Cable connector orientation LCM connector orientation male face view female Reference: Line Zero minutes POBox DB Amsterdam 11
USER MANUAL V5.0 ST100
GPS Vehicle Tracker USER MANUAL V5.0 ST100 Updated on 15 September 2009-1 - Contents 1 Product Overview 3 2 For Your Safety 3 3 ST100 Parameters 3 4 Getting Started 4 4.1 Hardware and Accessories 4 4.2
More informationInwall 4 Input / 4 Output Module
Inwall 4 Input / 4 Output Module IO44C02KNX Product Handbook Product: Inwall 4 Input / 4 Output Module Order Code: IO44C02KNX 1/27 INDEX 1. General Introduction... 3 2. Technical data... 3 2.1 Wiring Diagram...
More informationTemperature & Humidity SMS Alert Controller
Temperature & Humidity Alert Controller METERS 3 simple steps starting the unit: Insert the SIM card Plug in the sensors connectors Connect the AC power cord. Specifications: AC 90~260V Auto Select Internal
More informationThe $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit.
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit. Micro Wizard has been manufacturing Pinewood Derby timers for over 10 years.
More informationREGTRONIC OPERATING INSTRUCTIONS
REGTRONIC OPERATING INSTRUCTIONS 1.FEATURES Electrical connection: M12 8-pin connector Preset pressure range 0.05-10 bar with possible full scale regulation. 10 100 mbar adjustable deadband Supply pressure:
More informationTechnical data. General specifications. Indicators/operating means. 30 Hz Multiplex operation 30 Hz / n, n = number of sensors, n 5
Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service program ULTRA 000 programmable switch outputs Hysteresis
More informationUSB-500/600 Series Low-Cost Data Loggers and Accessories
Low-Cost Data Loggers and Accessories Features Stand-alone, remote data loggers and portable logger assistant Measure temperature, humidity, voltage, current, or event/state change 1 or 2 channels Low
More informationKit 106. 50 Watt Audio Amplifier
Kit 106 50 Watt Audio Amplifier T his kit is based on an amazing IC amplifier module from ST Electronics, the TDA7294 It is intended for use as a high quality audio class AB amplifier in hi-fi applications
More informationProduct Information S N O. Portable VIP protection CCTV & Alarm System 2
Product Information S N O Portable VIP protection CCTV & Alarm System 2 G O V E R N M E N T A L S E C U R I T Y S O L U T I VIP KIT Rapid Deployment VIP Protection Kit The VIP KIT has been designed to
More informationOWNERS MANUAL. WattsVIEW. Power Monitor Model: DC-10000. http://wattsview.com. WattsVIEWTM. Models: DC-10000 Serial DC-1000 USB DC-25000
WattsVIEW Power Monitor Model: DC-10000 DC Power Monitoring Made Easy Models: DC-10000 Serial DC-1000 USB DC-25000 OWNERS MANUAL PAGE 1 of 23 Table of Contents WattsVIEW Power Monitor Model: DC-10000...1
More informationJNIOR. Overview. Get Connected. Get Results. JNIOR Model 310. JNIOR Model 312. JNIOR Model 314. JNIOR Model 410
The INTEG is an Ethernet I/O (digital, analog) device that monitors and controls a small set of process signals. functions as both basic I/O for integration with another application or system AND as a
More informationNortechCommander Software Operating Manual MAN-00004 R6
NortechCommander Software Operating Manual MAN-00004 R6 If the equipment described herein bears the symbol, the said equipment complies with the applicable European Union Directive and Standards mentioned
More informationLED red (-): Measuring value < lower tolerance threshold LED red (+): Measuring value > upper tolerance threshold. Page 1/6
L-LAS Series L-LAS-LT-165-CL - Line laser 1 mw, laser class 2 - Visible laser line (red light 670 nm), typ. 2 mm x 3 mm - Reference distance approx. 165 mm - Measuring range typ. 65... 265 mm - Resolution
More information1. SAFETY INFORMATION
RS-232 Sound Level Meter 72-860A INSTRUCTION MANUAL www.tenma.com 1. SAFETY INFORMATION Read the following safety information carefully before attempting to operate or service the meter. Use the meter
More informationUSB-500 Series Low-Cost Data Loggers and Accessories
Low-Cost Data Loggers and Accessories Features Stand-alone, remote data loggers and portable logger assistant Measure temperature, humidity, voltage, current, or event/state change 1 or 2 channels Low
More informationNETWORK ENABLED EQUIPMENT MONITOR
NETWORK ENABLED EQUIPMENT MONITOR Remotely Monitor Sensors over the Internet Connect Sensors to the Web to Remotely Monitor Equipment, Processes or Other Applications A Complete, Easy to Deploy, Stand-Alone
More informationHCS-3300/3302/3304 USB Remote Programmable Laboratory Grade Switching Mode Power Supply
1. INTRODUCTION HCS-3300/3302/3304 USB Remote Programmable Laboratory Grade Switching Mode Power Supply User Manual This family of efficient, upgraded SMPS with small form factor, auto cross over CV CC,
More informationHow To Use A Ds340 (Dsp)
Ideal for monitoring dust levels in the exhaust gas of industrial combustion or air filtration processes. Innovative Dynamic Detection Principle (DDP) measurement technique Immune to gradual reductions
More informationUSB to RS-422/485 Serial Adapter
USB to RS-422/485 Serial Adapter User Manual Ver. 2.00 All brand names and trademarks are properties of their respective owners. Contents: Chapter 1: Introduction... 3 1.1 Product Introduction... 3 1.2
More informationController board and power supply for vivimat III systems
Controller board and power supply for vivimat III systems Ref: VIVIMAT-3.0 The controller board and power supply vivimat 3.0, is the central core of the vivimat III home automation system. The vivimat
More informationProduct Data. Thermal Comfort Data Logger Type 1221. Including Application Software Type 7301
Product Data Thermal Comfort Data Logger Type 1221 Including Application Software Type 7301 USES: For measuring all physical parameters necessary to evaluate heat stress and thermal comfort For evaluating
More informationWEA-Base. User manual for load cell transmitters. UK WEA-Base User manual for load cell transmitters Version 3.2 UK
WEA-Base User manual for load cell transmitters 1 Contents 1. Technical data... 3 2. Assembly... 4 2.1 Power supply... 4 2.2 Load cells... 4 2.3 RS-485... 4 2.4 Relays... 5 2.5 Digital input... 5 2.6 Analogue
More informationKit Highlights and Key Features
AF-OLK6 Series Fiber Optic Test kit (Data Storage Kit) Product: OLK6 Series Date: Aug:2007 Rev: 01 Description The AF-OLK6 series test kits are the complete solution necessary for the installer to test,
More informationViZion Installation Guide
ViZion Installation Guide v2.0 1 ViZion Installation Guide Table of Contents Inventory Hardware Setup Understanding Synchronization Cable Begin by taking an inventory of the required equipment DR Unit
More informationDOSISYS. Hands Free Reader LDM 210 - LDM 220. User Manual 127356A
DOSISYS LDM 210 - LDM 220 Hands Free Reader User Manual 127356A Publication, translation and reproduction total or partial of this document is strictly forbidden without authorization MGP Instruments
More informationStandard Cables (Without electromagnetic brake, with electromagnetic brake) CC010ES-2. 1 m CC020ES-2. 2 m CC030ES-2. 3 m CC050ES-2.
Motorized Actuators Motor Cables EZS /EZS for Clean Room Use This cable is a dedicated cable for connecting the linear slide of the EZS Series and EZS Series for Clean Room Use with the controller. Use
More informationX2 LR Optical Transponder, 10Km Reach
X2 LR Optical Transponder, 10Km Reach Features Compatible with X2 MSA Rev2.0b Support of IEEE 802.3ae 10GBASE-LR at 10.3125Gbps Transmission Distance up to 10km(SMF) SC Receptacle 1310nm DFB Laser SC Duplex
More informationTechnical Datasheet Scalar Network Analyzer Model 8003-10 MHz to 40 GHz
Technical Datasheet Scalar Network Analyzer Model 8003-10 MHz to 40 GHz The Giga-tronics Model 8003 Precision Scalar Network Analyzer combines a 90 db wide dynamic range with the accuracy and linearity
More information5000V Graphical Megohmmeter Model 5070
5000V Graphical Megohmmeter Model 5070 The Model 5070, the latest design in 5000V Megohmmeters, is the most innovative product in its class on the market today. The features and functions incorporated
More informationOmega ICD Intelligent Colour Display
Omega ICD Intelligent Colour Display Cosworth's Omega ICD is a widescreen TFT colour display coupled with a fully featured data logger in a single attractive aluminium housing. Using a widescreen 6.2"
More informationTS510 & TS500. Installation & User Guide. Compatible Equipment
Installation & User Guide Compatible Equipment TS510 REM - Remote Keypad 9040 - Loudspeaker DC54/58 - Digital Communicator SD1+ - Speech Dialler 496525 Issue A 1 of 10 TS510 and TS500 Overview Introduction
More informationwww.lascarelectronics.com
FEATURES 0-30V d.c. measurement range Logging rates between 1s and 12hr Stores readings Connection via two screw terminals USB interface for set-up and data download User-programmable alarm thresholds
More informationHow To Use A 1232 On A 1236 On A Computer Or A Cell Phone
12-36-1000 Autodialler and Relay Telephone Interface 1.0 INTRODUCTION 12-36-1000 I/O Telephone Interface with AutoDialer The 12-36-1000 is a autodialer and telephone interface that can be used autonomously
More informationCombi B Alarm box. Mounting instructions
Combi B Alarm box Mounting instructions EN Mounting instructions Alarm box Combi B VdS, G113064, G113065, G113066 Table of Contents 1 Description... 3 2 System overview... 3 3 Structure... 3 3.1 Power
More informationLONGLINE 10Gbps 10km SFP+ Optical Transceiver
LONGLINE 10Gbps 10km SFP+ Optical Transceiver Features Optical interface compliant to IEEE 802.3ae 10GBASE-LR Electrical interface compliant to SFF-8431 Hot Pluggable 1310nm DFB transmitter, PIN photo-detector
More informationNC-12 Modbus Application
NC-12 Modbus Application NC-12 1 Table of Contents 1 Table of Contents... 2 2 Glossary... 3 SCADA...3 3 NC-12 Modbus in general... 3 4 Entire system... 4 4.1 PFC to PC connection alternatives...4 4.1.1
More informationOWNERS MANUAL. Status Monitor. for Windows 95, 98, ME, NT 4, 2000 & XP. SIGNALCRAFTERS TECH, INC. www.signalcrafters.com
OWNERS MANUAL Status Monitor for Windows 95, 98, ME, NT 4, 2000 & XP SIGNALCRAFTERS TECH, INC. www.signalcrafters.com 57 Eagle Rock Avenue, East Hanover, NJ 07936 Tel: 973-781-0880 or 800-523-5815 Fax:
More informationWespot. SecNurse A NEW GENERATION TECHNICAL AIDS USER S GUIDE
Wespot SecNurse A NEW GENERATION TECHNICAL AIDS USER S GUIDE EN This manual is published by OPTEX, without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies
More informationAdvanced Data Capture and Control Systems
Advanced Data Capture and Control Systems Tronisoft Limited Email: sales@tronisoft.com Web: www.tronisoft.com RS232 To 3.3V TTL User Guide RS232 to 3.3V TTL Signal Converter Modules P/N: 9651 Document
More information8.5Gb/s SFP+ Fibre Channel Optical Transceiver
8.5Gb/s SFP+ Fibre Channel Optical Transceiver Features Up to 8.5Gb/s bi-directional data links Hot Pluggable SFP+ footprint Built-in digital diagnostic functions 1310nm FP laser transmitter Duplex LC
More informationShort Form Catalogue. Alarm Systems. Reliable Supervision and Control
Short Form Catalogue Alarm Systems Reliable Supervision and Control Alarm Monitors and Indicators The SELCO product range includes a number of alarm monitors and indicator panels for use in numerous applications.
More informationTechnical data. General specifications. Indicators/operating means. Electrical specifications Operating voltage U B Power consumption P 0 Interface
Release date: 06-0- 09: Date of issue: 06-0- 009_eng.xml Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service
More informationInstruction Manual Service Program ULTRA-PROG-IR
Instruction Manual Service Program ULTRA-PROG-IR Parameterizing Software for Ultrasonic Sensors with Infrared Interface Contents 1 Installation of the Software ULTRA-PROG-IR... 4 1.1 System Requirements...
More informationUser Manual. Humidity-Temperature Chart Recorder. Model RH520
User Manual Humidity-Temperature Chart Recorder Model RH520 Introduction Congratulations on your purchase of the Extech RH520 Temperature + Humidity Chart Recorder. The RH520 measures and displays Temperature,
More informationINSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930
INSTALLATION GUIDE Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 Card Reader and Controller Model 3.5 with KIM Swipe Reader Table of Contents 1. Features..................................
More informationRC2200DK Demonstration Kit User Manual
Demonstration Kit User Manual Table of contents TABLE OF CONTENTS... 1 QUICK INTRODUCTION... 2 INTRODUCTION... 3 DEMONSTRATION BOARD... 4 POWER SUPPLY SECTION... 5 RS-232 INTERFACE... 6 CONNECTORS... 7
More informationTCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL w w w. c d v g r o u p. c o m CA-ETHR-A: TCP/IP Module Installation Manual Page Table of Contents Introduction...5 Hardware Components... 6 Technical Specifications...
More informationELCOMPONENT LTD. User Manual
ELCOMPONENT LTD R-DCU - Remote Data a Collection Unit User Manual al CONTENTS Page 1. GENERAL... 1 2. SPECIFICATION... 4 3. INSTALLATION AND INSTRUCTIONS... 6 4. INSTRUMENT SET-UP AND RESET... 11 All rights
More informationABB i-bus EIB / KNX Analogue Input AE/S 4.2
Product Manual ABB i-bus EIB / KNX Analogue Input AE/S 4.2 Intelligent Installation Systems This manual describes the functionality of Analogue Input AE/S 4.2. Subject to changes and errors excepted. Exclusion
More informationTechnical description MX-1 VB Edge
1 (7) Technical description MX-1 VB Edge 2 (7) Table of Contents 1 General description...3 2 Connectors...4 3 ON/OFF operation...5 4 Power...5 5 LED indicators...6 6 Enclosure...6 7 Mounting...6 8 and
More information9452/9453 Installation and User Guide
9452/9453 Installation and User Guide Compatible Equipment 9425 Remote Keypad 9040 Internal Sounder 660 Speech Communicator 8440 4-Channel Minicom 496330 Issue 1 1 of 10 9452/3 Introduction The 9452 and
More informationMDM192 MULTI-DROPS DIGITAL MODEM FOR PRIVATE LINE. USER GUIDE Document reference : 9010709-03
MDM192 MULTI-DROPS DIGITAL MODEM FOR PRIVATE LINE USER GUIDE Document reference : 9010709-03 If you have questions about the MDM192 or desire assistance, contact ETIC TELECOMMUNICATIONS at the following
More informationVicon Flash Upgrade Software
INSTRUCTION MANUAL Notes Refer to XX134 NO. XX134-13-01 REV. 1212 Vicon Flash Upgrade Software It is possible to upgrade software for the SurveyorVFT and Surveyor -Mini Camera Domes through a PC using
More informationAlliance System Ordering Guide
Alliance System Ordering Guide Multiple Technologies Versatile Hardware Powerful Software One family of parts and accessories Version 12-Nov-03 Alliance System Ordering Guide Table of Contents Controllers
More informationSpecification of 5 Wire Analog Touch Panel
Specification of 5 Wire Analog Touch Panel 5 WIRE ANALOG RESISTIVE TOUCH PANEL A. Application This specification applies to the 5 Wire Analog Resistive Touch Panel. B. Environmental Conditions 1. Operating
More informationEMR-300 Broadband RF Survey Meter
Electric d Magnetic Field Measurement EMR-300 Broadbd RF Survey Meter Available with Isotropic Probes to cover 3 khz to 60 GHz Easy-to-Use Design Lightweight d Rugged Cost Effective Fully Automatic Zeroing
More informationVicon Flash Upgrade Software
NOTES NO. REV. SEC. INSTRUCTION MANUAL Refer to XX134-11-00 1108 3 XX134 Vicon Flash Upgrade Software It is possible to upgrade software for the SurveyorVFT through a PC using the Flash Upgrade software.
More informationMANUAL FOR RX700 LR and NR
MANUAL FOR RX700 LR and NR 2013, November 11 Revision/ updates Date, updates, and person Revision 1.2 03-12-2013, By Patrick M Affected pages, ETC ALL Content Revision/ updates... 1 Preface... 2 Technical
More informationUser's Guide. Integrating Sound Level Datalogger. Model 407780. Introduction
User's Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the Extech 407780 Product Page Integrating Sound Level Datalogger
More informationInstallation manual. Version 1.1. www.videx-security.com
Installation manual Version 1.1 www.videx-security.com 2 Table of Contents MANUAL INTRODUCTION... 4 SYSTEM INTRODUCTION... 4 SYSTEM COMPONENTS... 5 CONTROLS... 6 3.5A 13.8Vdc PSU... 6 CONTROL PCB... 6
More information2-Pair HDSL1 Adtran Fiber Optic Link System
ISSUE 2 June 01, 2004 Data Sheet #37 2-Pair HDSL1 Adtran Fiber Optic Link System Contents 1. General. 1 2. Application... 2 3. Housings.. 2 4. Installation 3 5. Provisioning. 5 6. LED Indicators. 6 7.
More informationSA-9600 Surface Area Software Manual
SA-9600 Surface Area Software Manual Version 4.0 Introduction The operation and data Presentation of the SA-9600 Surface Area analyzer is performed using a Microsoft Windows based software package. The
More informationHARTING mcon 1000 Introduction and features
Introduction and features HARTING mcon 1000 es, managed, for mounting onto top-hat mounting rail in control cabinets General Description Features Supporting Ethernet (10 Mbit/s), Fast Ethernet (100 Mbit/s)
More informationFOM-5A, 6A. Asynchronous Fiber Optic Modem
FOM-5A, 6A Asynchronous Fiber Optic Modem FEATURES Asynchronous transmission at up to 19.2 kbps Transmission range up to 3 km (1.8 mi), regardless of data rate Full- or half-duplex Transfers one control
More informationDifferential Pressure Sensors for air and non-corrosive gases, with calibration certificate
1 919 1919P01 1919P03 QBM65/C, QBM75-1U/C Differential Pressure Sensors for air and non-corrosive gases, with calibration certificate QBM751-1/C QBM65/C QBM75/C Highly accurate measurements with calibration
More informationPolyBot Board. User's Guide V1.11 9/20/08
PolyBot Board User's Guide V1.11 9/20/08 PolyBot Board v1.1 16 pin LCD connector 4-pin SPI port (can be used as digital I/O) 10 Analog inputs +5V GND GND JP_PWR 3-pin logic power jumper (short top 2 pins
More informationOrbit PCI Mk 2 Network Card. User Manual. Part No. 502566 Issue 4
Orbit PCI Mk 2 Network Card User Manual Part No. 502566 Issue 4 Information in this document is subject to change without notice. Companies, names and data used in examples herein are fictitious unless
More informationARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL
ARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL X1: DE-9 serial connector Used to connect computer (or other devices) using RS-232 standard. Needs a serial cable, with at least
More informationWireless Security Camera
Wireless Security Camera Technical Manual 12/14/2001 Table of Contents Page 1.Overview 3 2. Camera Side 4 1.Camera 5 2. Motion Sensor 5 3. PIC 5 4. Transmitter 5 5. Power 6 3. Computer Side 7 1.Receiver
More informationQuick Installation. A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding. Quick Installation
Quick Installation A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding This chapter intends to get your new FuzzyScan scanner working with your existing system within minutes. General instructions
More informationIntesisBox KNX Modbus RTU master
IntesisBox KNX RTU master Gateway for integration of RTU devices into KNX control systems. Integrate RTU devices (Chillers, Roof Tops, electricity meters, heating floors, heat pumps, PLCs ) into KNX control
More informationIncubator with mechanical convection
BF series 400 Incubators and cooling incubators Incubator with mechanical convection The BINDER incubator of the BF series with mechanical convection is suitable for all gentle incubation applications,
More informationInstallation Manual for D1110 DigiCom2
Installation Manual for D1110 DigiCom2 Dycon Ltd Tel: +44 (0)1443 471 060 Fax: +44 (0)1443 479 374 Cwm Cynon Business Park Mountain Ash CF45 4ER - UK www.dyconsecurity.com sales@dyconsecurity.com TABLE
More informationSturdy aluminium housing, anodized in blue Female connector for optical fiber (please order optical fiber separately) Mounting holes
SI-COLO Series SI-COLO2-LWL-HAMP-COL4 - Big measuring range: typ. 25 mm... 40 mm (with optical fiber and attachment optics KL-14 or KL-17) - Large assortment of optical fibers available (reflected or transmitted
More informationRS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
More informationProduct Specification. RoHS-6 Compliant 10Gb/s 850nm Multimode Datacom XFP Optical Transceiver FTLX8512D3BCL
Product Specification RoHS-6 Compliant 10Gb/s 850nm Multimode Datacom XFP Optical Transceiver FTLX8512D3BCL PRODUCT FEATURES Hot-pluggable XFP footprint Supports 8.5Gb/s and 9.95 through 10.5Gb/s* bit
More informationMOTION COORDINATOR MC206X Quick Connection Guide
I/O Connector 1 Analogue In / Inputs 0-7 5 Way Connector Power /CANbus I/O Connector 2 24V Power / I/O 8-15 I/O Connector 3 WDOG / Ref Encoder / Analogue Outputs USB Serial A Serial B Axes 0-3 Encoder
More informationAC-115 Compact Networked Single Door Controller. Installation and User Manual
AC-115 Compact Networked Single Controller Installation and User Manual December 2007 Table of Contents Table of Contents 1. Introduction...5 1.1 Key Features... 6 1.2 Technical Specifications... 7 2.
More informationQFP910. Water detector. Building Technologies. CE1N2732en. Synco living
2 732 Synco living Water detector QFP910 Wireless radio sensor to record water puddles RF communication based on KNX standard (868 MHz unidirectional) Battery operation with standard 1.5 V batteries Use
More informationStand Alone POTS Fiber Optic System. P31372 Station (Subscriber) Unit P31379 Remote (Exchanger) Unit. Description & Installation
Stand Alone POTS Fiber Optic System P31372 Station (Subscriber) Unit P31379 Remote (Exchanger) Unit Description & Installation Printed in USA 09/11 TO466 Rev. A Table of Contents Page 1.0 SCOPE 2 2.0 PRODUCT
More informationMAVO-MONITOR / MAVO-SPOT Instrument Set for Contact or Distant Measurements of Luminances
Operating Instructions MAVO-MONITOR / MAVO-SPOT Instrument Set for Contact or Distant Measurements of Luminances 15043 1/1.00 10 9 8 1 7 6 1 Display 2 Slider switch cd/m² segment test 3 ON/OFF switch 4
More informationDuct Humidity Transmitter
SDC-H Duct Humidity Transmitter Features Replaceable sensor element Humidity measurement for air ducts Minimum and maximum value memory 0 0V, 0 0mA or 0V, 4 0mA measuring signals selectable with jumpers
More informationTemperature sensor with integrated transmitter for industrial applications, MBT 3560
Temperature sensor with integrated transmitter for industrial applications, MBT 3560 Technical brochure Features Designed for use in harsh industrial enviroments where reliable, robust and accurate equipment
More informationEL-USB-2-LCD FEATURES WINDOWS CONTROL SOFTWARE DISPLAY FUNCTIONS. www.lascarelectronics.com Page 1 of 5
This standalone data logger measures and stores up to 16,379 relative humidity and 16,379 temperature readings over 0 to 100%RH and -35 to +80 C (-31 to +176 F) measurement ranges. The user can easily
More informationis then retained absolutely without interruption.
Page 1 of 11 DC UPS uninterruptible power supplies - DC UPS module 15 A Compact design, only 50 mm wide Absolutely interruption-free buffering of power failures through immediate electronic connection
More informationEASIDEW PORTABLE HYGROMETER INSTALLATION, OPERATION AND MAINTENANCE MANUAL
EASIDEW PORTABLE HYGROMETER INSTALLATION, OPERATION AND MAINTENANCE MANUAL Issue February 2004 2 TABLE OF CONTENTS SECTION PAGE 1. INTRODUCTION 3 1.1 General 3 1.2 Ceramic Sensing Element 3 1.3 Calibration
More informationCruzPro VAF110. AC Volts, Amps, Frequency, kw Monitor
CruzPro VAF110 AC Volts, Amps, Frequency, kw Monitor Table of Contents Introduction............................ 3 Specifications........................... 4 Installation..............................5
More informationINTELLIGENT CONTROL MODULE SA-2000-II HARDWARE MANUAL. Access Technologies International, Inc.
SA-2000-II HARDWARE MANUAL Access Technologies International, Inc. 1 Table of Contents 1. Introduction 3 2. Features 3 3. Specification 4 4. Identifying Supplied Parts 4 5. Panel Description 5 6. Connection
More informationAuxiliary equipment for communication with the EuroProt protective devices
Auxiliary equipment for communication with the EuroProt protective devices RS232 cable This cable is used to connect the RS232 connector located on the front panel of the EuroProt devices to the 9 pin
More informationMultiViu Flex 7 Data Sheet
Division Interior MultiViu Flex 7 Data Sheet Picture: MultiViu Flex 7 Picture: MultiViu Flex 7 Description CAN-capable multifunction Solution Features: Robust and versatile design CAN-capability (SAE J1939,
More informationNardalert S3 Non-Ionizing Radiation Monitor
Patent Pending Non-Ionizing Radiation Monitor Field Replaceable Sensor Modules Color LCD Display Multi-Color Alarm LED s USB Interface for Data and Charging Interchangeable Lanyard or Belt Clips Comprehensive
More informationDynamax Inc Copyright 2012-13
SAPIP Tester Cable TEST Operating Guide Troubleshoot SapIP with signal issues while in the Field or the Lab Troubles shoot cables with basic VOM tests. Section One Low Voltage SAPIP Tester - Heater Supply
More informationMAKE OF AUTOMOBILE: NUMBER : 076/0800901 DATE : 2008-12-08 Copyright Prins Autogassystemen B.V. 2008 VERSION NR : 2008-10-24 B
MAKE OF AUTOMOBILE: HONDA TYPE: CIVIC PISTON DISPLACEMENT: 1800 NUMBER OF VALVES: 16 ENGINE NUMBER: R18A TYPE VSI INJECTOR ( COLOR ) ORANGE MODEL YEAR: 2008 ENGINE SET NUMBER 348/0250200.07 NUMBER : 076/0800901
More informationSECTION 16715 TELECOMMUNICATIONS ACCEPTANCE TESTING
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Testing Publications and Standards B. Inspection and testing procedures for copper and fiber optic cable, RF CATV / MATV systems, and the antenna systems. C. Documentation
More informationDS2438EVKIT+ Smart Battery Monitor Evaluation Kit
19-4829; Rev 1; 8/09 www.maxim-ic.com DS2438EVKIT+ Smart Battery Monitor Evaluation Kit FEATURES Demonstrates the Capabilities of the DS2438 Smart Battery Monitor, Including: Temperature Measurement Voltage
More informationSix-servo Robot Arm. DAGU Hi-Tech Electronic Co., LTD www.arexx.com.cn. Six-servo Robot Arm
Six-servo Robot Arm 1 1, Introduction 1.1, Function Briefing Servo robot, as the name suggests, is the six servo motor-driven robot arm. Since the arm has a few joints, we can imagine, our human arm, in
More informationMiniPlex-41USB NMEA-0183 multiplexer Manual
MiniPlex-41USB NMEA-0183 multiplexer Manual MiniPlex-41USB, V1.0 Firmware V1.30 CustomWare, 2004 Introduction The MiniPlex-41USB is a four-channel NMEA multiplexer, enabling the connection of multiple
More informationPACKAGE OUTLINE DALLAS DS2434 DS2434 GND. PR 35 PACKAGE See Mech. Drawings Section
PRELIMINARY DS2434 Battery Identification Chip FEATURES Provides unique ID number to battery packs PACKAGE OUTLINE Eliminates thermistors by sensing battery temperature on chip DALLAS DS2434 1 2 3 256
More informationABLOY DA60 SWING DOOR OPERATOR Installation and commissioning manual Abloy Oy An ASSA ABLOY Group company APPROVALS / STANDARDS Low Voltage directive 7//EEC as amended by the directive 9/68/EEC EMC directive
More informationAuto-tune PID. Temperature Controller BRAINCHILD FEATURES
Auto-tune PID Temperature Controller FEATURES Easy-to-use Fuzzy modified PID heat & cool control Fast A-D sampling rate (5 times/s) Universal input (PT100, thermocouple) with high accuracy 18-bit A-D Analog
More information