Setup software RAID1 array on running CentOS 6.3 using mdadm. (Multiple Device Administrator) 1. Gather information about current system.

Transcription

1 Setup software RAID1 array on running CentOS 6.3 using mdadm. (Multiple Device Administrator) All commands run from terminal as super user. Default CentOS 6.3 installation with two hard drives, /dev/sda and /dev/sdb which are identical in size. Machine name is serverbox.local. /dev/sdb is currently unused, and /dev/sda has the following partitions: /dev/sda1: /boot partition, ext4; /dev/sda2: is used for LVM (volume group vg_serverbox) and contains / (volume root), swap (volume swap_1) and /home (volume home). Final RAID1 configuration: /dev/md0 (made up of /dev/sda1 and /dev/sdb1): /boot partition, ext4; /dev/md1 (made up of /dev/sda2 and /dev/sdb2): LVM (volume group vg_serverbox), contains / (volume root), swap (volume swap_1) and /home (volume home). 1. Gather information about current system. Report the current disk space usage: df -h View physical disks: fdisk -l View physical volumes on logical disk partition: pvdisplay View virtual group details: vgdisplay View Logical volumes: lvdisplay Load kernel modules (to avoid a reboot): modprobe linear modprobe raid0 modprobe raid1

2 Verify personalities: The output should look as follows: serverbox:~# Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] unused devices: <none> 2. Preparing /dev/sdb To create a RAID1 array on a running system, prepare the /dev/sdb hard drive for RAID1, then copy the contents of /dev/sda hard drive to it, and finally add /dev/sda to the RAID1 array. Copy the partition table from /dev/sda to /dev/sdb so that both disks have exactly the same layout: sfdisk -d /dev/sda sfdisk f /dev/sdb Verify both disks are partitioned identically: fdisk -l Change the partition type of partitions on /dev/sdb to Linux raid autodetect: fdisk /dev/sdb serverbox:~# fdisk /dev/sdb Command (m for help): t [t = change a partition's system id] Partition number (1-5): 1 Hex code (type L to list codes): fd [fd = Linux raid auto] Command (m for help): t Partition number (1-5): 2 Hex code (type L to list codes): fd Command (m for help): w [w = write changes to disk] Verify changes written successfully: fdisk -l Remove any previous RAID installations on /dev/sdb : (error displayed if none exist) mdadm --zero-superblock /dev/sdb1 mdadm --zero-superblock /dev/sdb2

3 3. Creating RAID Arrays Create RAID arrays /dev/md0 and /dev/md1. /dev/sdb1 will be added to /dev/md0 and/dev/sdb2 to /dev/md1. mdadm --create /dev/md0 --metadata= level=1 --raid-disks=2 missing /dev/sdb1 mdadm --create /dev/md1 --metadata= level=1 --raid-disks=2 missing /dev/sdb2 Verify array created: ([_U] or [U_] means that an array is degraded while [UU] means that the array is ok) Create a file system (ext4) on our non-lvm RAID array /dev/md0: mkfs.ext4 /dev/md0 Logical volumes: Initialize physical volume /dev/md1 for LVM: (Logical Volume Manager) pvcreate /dev/md1 Add /dev/md1 to our volume group vg_serverbox: vgextend vg_serverbox /dev/md1 Verify array /dev/md1 added to logical volume group: pvdisplay Review volume group details: (optional) vgdisplay Update configuration file /etc/mdadm.conf : cp /etc/mdadm.conf /etc/mdadm.conf_orig mdadm --examine --scan >> /etc/mdadm.conf Review the updated configuration file: (Array devices added at end.) cat /etc/mdadm.conf

4 Modify file /etc/fstab. Replace /dev/sda1 with /dev/md0 so that the line looks as follows: gedit /etc/fstab /dev/md0 /boot ext4 defaults 0 2 Modify file /etc/mtab. Replace line containing /dev/sda1 with /dev/md0: gedit /etc/mtab /dev/md0 /boot ext3 rw 0 0 Open /boot/grub/menu.lst and add fallback 1 right after default 0: gedit /boot/grub/menu.lst default 0 fallback 1 Duplicate first kernel stanza [title... savedefault]. In first stanza; replace root (hd0,0) with root (hd1,0): title Vg_serverbox GNU/Linux, kernel root (hd1,0) kernel /vmlinuz root=/dev/mapper/vg_serverbox-root ro initrd /initrd.img savedefault title Vg_serverbox GNU/Linux, kernel root (hd0,0) kernel /vmlinuz root=/dev/mapper/vg_serverbox-root ro initrd /initrd.img savedefault * REMOVE any kernel options that prevent loading md devices (not dm ).

5 Rebuild initramfs using mdadm.conf: mv /boot/initramfs-$(uname r).img /boot/initramfs-$(uname r).img.old dracut --mdadmconf --force /boot/initramfs-$(uname r).img $(uname r) 4. Moving Data to the RAID Arrays Copy data from boot partition /dev/sda1 to array /dev/md0: (assuming /dev/sda1 is mounted at /boot) mkdir /mnt/raid mount /dev/md0 /mnt/raid cd /boot; find. depth cpio pmd /mnt/raid touch /mnt/raid/.autorelabel sync umount /mnt/raid Move the contents of LVM partition /dev/sda2 to LVM RAID array /dev/md1: (takes approx. 45 min. for 200 GB) pvmove /dev/sda2 /dev/md1 Remove /dev/sda2 from the volume group vg_serverbox: vgreduce vg_serverbox /dev/sda2 Remove volume /dev/sda2 from LVM: pvremove /dev/sda2 Verify /dev/md1 is the only physical volume for volume group vg_serverbox: pvdisplay

6 Change the partition type of /dev/sda2 to Linux raid autodetect: fdisk /dev/sda Command (m for help): t Partition number (1-5): 2 Hex code (type L to list codes): fd Command (m for help): w The partition table has been altered! Add /dev/sda2 to /dev/md1 array: (Takes approx. 35 min. for 200 GB array to be rebuilt) mdadm --add /dev/md1 /dev/sda2 Monitor rebuild in progress: (To leave watch, press CTRL+C.) watch n 5 5. Preparing GRUB Install the GRUB bootloader on the hard drive /dev/sda and /dev/sdb: grub grub> root (hd0,0) setup (hd0) root (hd1,0) setup (hd1) quit Verify system will boot: reboot After system reboots verify /dev/md0 is mounted at /boot: df -h

7 Verify arrays are active: (status should be /dev/md1 [UU] and /dev/md0 [_U] ) Verify logical volumes using pvdisplay, vgdisplay, and lvdisplay : (optional) pvdisplay vgdisplay lvdisplay Change the partition type of /dev/sda1 to Linux raid autodetect: fdisk /dev/sda Command (m for help): t Partition number (1-5): 1 Hex code (type L to list codes): fd Command (m for help): w Add /dev/sda1 to the /dev/md0 RAID array: (takes < 1 min.) mdadm --add /dev/md0 /dev/sda1 Verify both volumes are active and running [UU]: Update /etc/mdadm.conf : cp /etc/mdadm.conf_orig /etc/mdadm.conf mdadm --examine --scan >> /etc/mdadm.conf Reboot the system: reboot That's it - software RAID1 array is active and running!

8 Testing and rebuilding Physically remove drive from system, or; Simulate a hard drive failure. [ /dev/sdb ] mdadm --manage /dev/md0 --fail /dev/sdb1 mdadm --manage /dev/md1 --fail /dev/sdb2 mdadm --manage /dev/md0 --remove /dev/sdb1 mdadm --manage /dev/md1 --remove /dev/sdb2 Shut down the system: shutdown -h now Reboot: System should boot in degraded state. Verify array is active but degraded: ( [_U] or [U_] ) Shut down the system: shutdown -h now Put in a new /dev/sdb drive, or if failure of /dev/sda, move /dev/sdb to failed /dev/sda slot and connect the new HDD as /dev/sdb. Boot the system. Verify /dev/sda is boot device and /dev/sdb is empty. fdisk -l Copy the partition table of /dev/sda to /dev/sdb: sfdisk -d /dev/sda sfdisk f /dev/sdb Remove any remains of the RAID array from /dev/sdb: mdadm --zero-superblock /dev/sdb1 mdadm --zero-superblock /dev/sdb2

9 Add /dev/sdb to the RAID array: mdadm -a /dev/md0 /dev/sdb1 mdadm -a /dev/md1 /dev/sdb2 Monitor the rebuilding process: watch n 5 Wait until the synchronization has finished: Install the bootloader on both HDDs: grub grub> root (hd0,0) setup (hd0) root (hd1,0) setup (hd1) quit That's it. Failed hard drive in RAID1 array is replaced.