Beckhoff onboard SATA-RAID

Size: px
Start display at page:

Download "Beckhoff onboard SATA-RAID"

Transcription

1 Installation and operating instructions for Beckhoff onboard SATA-RAID Version: 1.3 Date:

2

3 Table of contents Table of contents General notes 2 Notes on the documentation 2 Liability conditions 2 Description of safety symbols 2 Basic safety measures 3 Product description 4 RAID overview 4 RAID level 4 RAID 1 (mirroring) 4 Configuration at delivery state 4 Status information 5 Status information from BIOS 5 Display during normal operation 5 Display after the failure of a hard disk 6 Display after the replacement of a defective hard disk 7 Status information under Windows 8 Display during normal operation 8 Display after the failure of a hard disk 8 Exchanging a defective hard disk 9 Rebuilding the RAID system 10 Requirements for a replacement hard disk 10 Resetting a replacement hard disk for the RAID rebuild 10 Resetting a replacement hard disk with the Configuration Utility 11 Resetting a replacement hard disk with the Storage Console 11 RAID rebuild under BIOS Selecting a hard disk for the RAID rebuild RAID rebuild under Windows 15 Selecting a hard disk (drive) for the RAID rebuild 15 Starting the RAID rebuild in the standard view of the Storage Console 15 Starting the RAID rebuild in the extended view of the Storage Console 17 Rebuild process 19 Storage Console is closed 19 Rebuild process from the Storage Console 19 Extended view of the Storage Console 20 RAID diagnosis under TwinCAT 21 TwinCAT RAID diagnosis Querying the information Beckhoff Support & Service 22 Beckhoff's branch offices and representatives 22 Beckhoff headquarters 22 Beckhoff Support 22 Beckhoff Service 22 Appendix 23 System requirements 23 Approvals 23 FCC: Federal Communications Commission 23 Radio Frequency Interference Statement 23 FCC: Canadian Notice 23 1 Beckhoff onboard SATA-RAID

4 General notes General notes Notes on the documentation This description is only intended for the use of trained specialists in control and automation technology who are familiar with the applicable national standards. It is essential that the following notes and explanations are followed when installing and commissioning these components. Liability conditions The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards. The documentation has been prepared with care. The products described are, however, constantly under development. For this reason, the documentation may not always be have been fully checked for consistency with the performance data, standards or other characteristics described. None of the statements in this manual represent a guarantee for as set out in 443 of the German Civil Code or a statement about the assumed use according to the contract as set out in 434 para. 1 clause 1 no. 1 of the German Civil Code. In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation. This documentation is protected by copyright. Any reproduction or third party use of this publication, whether in whole or in part, without the written permission of Beckhoff Automation GmbH, is forbidden. Description of safety symbols The following safety symbols are used in this operating manual. They are intended to alert the reader to the associated safety instructions. Warning i Note This symbol is intended to highlight risks for equipment, materials or the environment. This symbol indicates information that contributes to better understanding. 2 Beckhoff onboard SATA-RAID

5 General notes Only switch the PC off after closing the software Warning Basic safety measures Before the Industrial PC is switched off, software that is running must be properly closed. Otherwise it is possible that data on the hard disk is lost. Switch off all parts of the equipment, then uncouple the fieldbus! Before opening the PC housing, for example to exchange a hard disk, all system parts must be switched off first and the Industrial PC must then be uncoupled from the system. Pulling out the fieldbus connection plug uncouples the PC (optional). System components that have been switched off must be secured against being switched on again. Warning Do not exchange any parts when under power! When components are being fitted or removed, the supply voltage must be switched off. Fitting work on the Industrial PC can result in damage: If metal objects such as screws or tools fall onto operating circuit boards. If connecting cables internal to the PC are removed or inserted during operation. If plug-in cards are removed or inserted when the PC is switched on. i Note Hard disks in hard drive caddies can also be exchanged whilst the Industrial PC is in operation. Beckhoff onboard SATA-RAID 3

6 Product description Product description RAID overview RAID system (Redundant Array of Independent Drives) A RAID system (Redundant Array of Independent Drives) serves to organize several physical hard disks in a computer into one logical drive (array). The essential aim of RAID systems is to support error tolerance and to improve the performance of the memory sub-system. i Note RAID level From the point of view of the user or an application program, there is no distinction between a logical RAID drive and a single hard disk. RAID level The RAID level defines how the data within the volume that encompasses the hard disks in the array is formatted. The Intel(R) Matrix Storage Manager supports RAID Level 1 (mirroring) amongst others. RAID 1 (mirroring) RAID 1 The RAID 1 level combines two or more hard disks so that all data is written simultaneously to all array members of the RAID 1 volume. In other words: the data is mirrored and distributed across the hard disks in the RAID 1 volume. This creates real-time redundancy of all of the data on the first drive. Due to the increased protection against failure, RAID 1 is normally used for storing critical data. Besides complete data redundancy, a further advantage is the increased reading transmission rate. Configuration Configuration at delivery state Industrial PCs with the CB1051 motherboard, which are delivered with more than one hard disk (HDD) are equipped with the SATA RAID system as standard. Two of the hard disks are then combined logically to make a RAID 1 drive. The hard disks can be permanently installed inside the computer or also accessible from outside via hard drive caddies. 4 Beckhoff onboard SATA-RAID

7 Status information Status information The configuration of the system can be accomplished both in BIOS and under Windows. Furthermore it is possible to recall the status of the system in TwinCAT. Status information from BIOS RAID status Display during normal operation The first possibility to obtain information about the RAID status is during the BIOS boot process. The second boot screen shows a summary of the RAID status: Configuration Utility In this screen, the Configuration Utility can be opened with Ctrl I: Beckhoff onboard SATA-RAID 5

8 Status information Failure of a hard disk Display after the failure of a hard disk If the computer is restarted following the failure of a hard disk, the second boot screen may look like this, for example: Configuration Utility The status of the RAID volume is described here as Degraded. The status of the hard disk on Port 0 can be seen to be okay (green). If more than 2 SATA hard disks are installed inside the PC and one of the two hard disks in the RAID volume failes or the hard disk configuration inside the PC was changed because of other reasons, then at the next start or reboot of the PC it is required to enter the BIOS Setup. Go to "Advanced BIOS Features" "Hard Disk Boot Priority" and move the "INTEL VOLUME0" to the top position by using the cursor down and the picture up key. Otherway the PC will try to boot from hard disk three or four instead of booting from the RAID volume. The Configuration Utility does not display any further information: 6 Beckhoff onboard SATA-RAID

9 Status information Without rebuilding the RAID volume Boot screen Display after the replacement of a defective hard disk If the defective hard disk was exchanged (please refer to chapter Requirements for a replacement hard disk) whilst the Industrial PC was switched off, or if the hard disk was exchanged under Windows during operation without starting a rebuild of the RAID volume, the second boot screen will appear as follows at the next PC start-up: A hard disk is shown on Port 1 that does not belong to any RAID volume. The new hard disk can be selected in the Configuration Utility for the rebuild of the RAID volume (see chapter Selecting a hard disk for the RAID rebuild). However, it is also possible, without first opening the Configuration Utility, to boot Windows, where the hard disk can then also be selected for the rebuild of the RAID volume (see chapter Selecting a hard disk (drive) for the RAID rebuild). Beckhoff onboard SATA-RAID 7

10 Status information Status information under Windows Normal operation Display during normal operation Under Windows the RAID system works in the background, i.e. under the operating system the user sees a logical drive that is indistinguishable from a single hard disk. There is no indication that the system is working properly. Failure of a hard disk Display after the failure of a hard disk Following the failure of a hard disk, a message appears in the task bar at the bottom right at each restart or new logon. Example: Port 0 and Port 1 are each connected to a hard disk; the two disks together form a RAID 1 volume. If the data cable is unplugged from the hard disk on Port 1, the following message appears: Storage Console Warning Clicking on the message opens the standard view of the Storage Console. The opening and usage of the Storage Console can under certain circumstances lead to impairment of real-time capability! In this example the hard disk on Port 0 (connection 0) is okay (shown in green). Storage Console: Example The extended view of the Storage Console, which contains further information, can be opened via the View menu: 8 Beckhoff onboard SATA-RAID

11 Status information Extended view of the Storage Console i Note Exchanging a defective hard disk The defective hard disk can be exchanged under Windows during operation without restarting the PC (hot swap). This is particularly easy if the hard disks are mounted in hard drive caddies (please refer to chapter Requirements for a replacement hard disk). If the defective hard disk is exchanged under Windows during operation, the rebuild of the RAID volume can subsequently be started (see chapter RAID rebuild under Windows). Beckhoff onboard SATA-RAID 9

12 Rebuilding the RAID system Rebuilding the RAID system Requirements for a replacement hard disk In an ideal case, a replacement hard disk is brand new and must have at least the same storage capacity as the drive which it is to replace. If no brand new hard disk is available, the following points must be observed: All data that was stored on a drive before it was used as a replacement hard disk will be lost as a result of its use as a replacement hard disk. Information about the RAID system is stored on every hard disk that belongs to a RAID system. Therefore a hard disk from the RAID system of a different computer must be reset with respect to RAID before it can be used as a replacement hard disk. i Note Resetting a replacement hard disk for the RAID rebuild The resetting of a replacement hard disk is only necessary if it comes from a RAID system. Hard disks can be reset in the Configuration Utility during the BIOS boot process or under Windows. It is not necessary to reset a replacement hard disk with the PC, in which it will be used later. For example the disk can also be reset in the PC it comes from. The hard disks of the PCs with or without hard drive caddies are labeled with the port numbers. i Note The hard disks can be identified best via their port numbers. For each hard disk the port is shown in the Configuration Utility and in the Storage Console. 10 Beckhoff onboard SATA-RAID

13 Rebuilding the RAID system Resetting a replacement hard disk with the Configuration Utility The hard disk is reset in the Configuration Utility under menu 3 Reset Disks to Non-RAID: Warning Resetting a replacement hard disk with the Storage Console The opening and usage of the Storage Console can under certain circumstances lead to impairment of real-time capability! With the Storage Console the according volume is reset, not the hard disk. After the volume that has to be reset was identified in the extended view of the Storage Console via the port of the according hard disk, Delete Volume has to be selected from the context menu of the according volume: Beckhoff onboard SATA-RAID 11

14 Rebuilding the RAID system Delete RAID Volume Wizard The wizard for deleting a RAID volume then appears: Selecting the Volume Clicking on Next opens the selection dialogue for the reset volume. The volume on which you previously right-clicked is already preselected. Clicking on Next will cause the warning to appear that any data will be lost. Clicking on Finish then completes the process. The volume (also the hard disk) will be reset now. 12 Beckhoff onboard SATA-RAID

15 Rebuilding the RAID system RAID rebuild under BIOS Selecting a hard disk for the RAID rebuild If the Configuration Utility is opened, there is a possibility to specify a newly connected hard disk (theoretically, more than one new hard disk may have been connected) for rebuilding the RAID volume. If more than 2 SATA hard disks are installed inside the PC and one of the two hard disks in the RAID volume failes or the hard disk configuration inside the PC was changed because of other reasons, then at the next start or reboot of the PC it is required to enter the BIOS Setup. Go to "Advanced BIOS Features" "Hard Disk Boot Priority" and move the "INTEL VOLUME0" to the top position by using the cursor down and the picture up key. Otherway the PC will try to boot from hard disk three or four instead of booting from the RAID volume. In the example, only the defective hard disk was replaced: Configuration Utility After a hard disk has been selected, the Configuration Utility shows the new hard disk as a member of the RAID volume with the ID 0. The status of the RAID volume was changed from Degraded to Rebuild. At the lower edge of the screen there is a notice that the rebuild process will first be started under the operating system. Beckhoff onboard SATA-RAID 13

16 Rebuilding the RAID system Rebuild process starts under the operating system i Note If a hard disk has been selected in the Configuration Utility for the rebuild, the rebuild process begins immediately under Windows (see chapter Storage Console is closed). 14 Beckhoff onboard SATA-RAID

17 Rebuilding the RAID system RAID rebuild under Windows Exchanging the defective hard disk Selecting a hard disk (drive) for the RAID rebuild If the replacement of the defective hard disk is carried out under Windows without having selected a hard disk for the rebuild up to that point, the following message will be displayed: Clicking on the message opens the Storage Console. Starting the RAID rebuild in the standard view of the Storage Console If a defective hard disk has merely been replaced by a new one, the rebuild of the RAID system can be started in the standard view. i Note For complicated cases there is a button in the standard view that opens the extended view (see chapter Starting the RAID rebuild in the extended view of the Storage Console). In the case that a hard disk from a RAID volume and a new empty hard disk are present, the target hard disk will not be queried. Beckhoff onboard SATA-RAID 15

18 Rebuilding the RAID system Clicking on the marked icon Restore RAID 1 data protection changes the view to: Clicking on the marked icon Rebuild RAID volume now will prompt the final question to be asked: After confirming with Yes the rebuild process starts (see chapter Rebuild process from the Storage Console). 16 Beckhoff onboard SATA-RAID

19 Rebuilding the RAID system Extended view of the Storage Console Starting the RAID rebuild in the extended view of the Storage Console All RAID volumes and all hard disk connections are shown in the extended view. In the following view it can be seen that a hard disk is missing that previously belonged to a RAID volume and also that a Non-RAID Hard Drive is connected to Port 1. Clicking with the right mouse button on this hard disk enables the option Rebuild to this Hard Drive to be selected: Rebuild wizard The wizard for rebuilding a RAID volume then appears: Clicking on Next opens the selection dialogue for the new RAID hard disk. The hard disk on which you previously right-clicked is already preselected. Beckhoff onboard SATA-RAID 17

20 Rebuilding the RAID system Selecting the hard disk Clicking on Next will cause the warning to appear that any data existing on the new hard disk will be lost during rebuilding: Warning If the rebuild of the RAID volume is started, all data on the selected hard disk will be irreversibly deleted! The rebuild is started by clicking on Finish (see chapter Extended view of the Storage Console). 18 Beckhoff onboard SATA-RAID

21 Rebuilding the RAID system Rebuild process Rebuild message Storage Console is closed When the rebuild process starts under Windows, this will be indicated by a message at the bottom right next to the clock: The animated icon is displayed throughout the entire rebuild process and disappears without a further message when the rebuild is complete. Clicking with the mouse on the message will open the Storage Console (see chapter Rebuild process from the Storage Console). Storage Console Rebuild process from the Storage Console Clicking on the message RAID Volume Rebuilding opens the Storage Console, where the progress of the process can be followed: Beckhoff onboard SATA-RAID 19

22 Rebuilding the RAID system Storage Console Once the rebuild process is complete, the Storage Console displays the following view: Progress display in the Console Extended view of the Storage Console If the corresponding volume is selected by clicking on it at the left-hand side during rebuilding, progress can be followed on the right-hand: 20 Beckhoff onboard SATA-RAID

23 RAID diagnosis under TwinCAT RAID diagnosis under TwinCAT The RAID system works in the background, i.e. under the operating system the user sees a logical drive that is indistinguishable from a single hard disk. The configuration of the system can be accomplished both in BIOS and under Windows. Furthermore it is possible to check the status of the system in TwinCAT. i Note TwinCAT RAID diagnosis The Storage Console must be installed in order to be able to use TwinCAT RAID diagnosis! As an alternative to the user interface of the Intel Matrix Storage Console, the TwinCAT RAID diagnosis offers a real-time-capable option for querying the status of the RAID system. In order to change the RAID system, however, the Storage Console must still be used. The information is queried by a standardized interface of the RAID driver. Querying the information The information query is divided into three steps: Step 1 Step 2 Step 3 i Note Information about the existing RAID controllers Here, both the number and the IDs of the existing RAID controllers are displayed. Information about the existing RAID volumes The numbers of existing volumes and hard disks are listed. Status of the existing RAID volumes The status is queried in each case for a single controller ID and a single set number: RAID type, status of the RAID volume (OK, degraded, rebuilding, failed), number of hard disks that make up the set, serial numbers of the hard disks that make up the set and the hardware ports on the motherboard to which the hard disks making up the set are connected. In the event of a failure it can hence be determined which hard disk is OK or which one must be replaced. In the case of delivery with hard drive caddies, these are each identified by a label showing the port number. A set is the combination of hard disks to form a RAID system. This is described as a volume in the operating system. Beckhoff onboard SATA-RAID 21

24 Beckhoff Support & Service Beckhoff Support & Service Beckhoff and their partners around the world offer comprehensive service and support, making available fast and competent assistance with all questions related to Beckhoff products and system solutions. Beckhoff's branch offices and representatives Please contact your Beckhoff branch office or representative for local support and service on Beckhoff products! The addresses of Beckhoff's branch offices and representatives round the world can be found on her internet pages: You will also find further documentation for Beckhoff components there. Beckhoff headquarters Beckhoff Automation GmbH Eiserstraße 5 D Verl Germany Phone: +49(0)5246/963-0 Fax: +49(0)5246/ Beckhoff Support Support offers you comprehensive technical assistance, helping you no only with the application of individual Beckhoff products, but also with other, wide-ranging services: world-wide support design, programming and commissioning of complex automation systems and extensive training program for Beckhoff system components Hotline: +49(0)5246/ Fax: +49(0)5246/ Beckhoff Service The Beckhoff Service Center supports you in all matters of after-sales service: on-site service repair service spare parts service hotline service Quote the project number Hotline: +49(0)5246/ Fax: +49(0)5246/ If servicing is required, please quote the project number of your Industrial PC. 22 Beckhoff onboard SATA-RAID

25 Appendix Appendix System requirements Operating system Windows XP from Service Pack 2 Other operating systems after consulting Beckhoff service TwinCAT Version At least TwinCAT version 2.10 build TwinCAT on the D partition: At least version 2.10 build In special cases Beckhoff service must be consulted. Hard disk capacity The hard disks in the RAID volume must have the same capacity FCC Approval for USA FCC Approval for Canada Approvals FCC: Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC: Canadian Notice This equipment does not exceed the Class A limits for radiated emissions as described in the Radio Interference Regulations of the Canadian Department of Communications. Beckhoff onboard SATA-RAID 23

Graphic Driver Installation Instructions

Graphic Driver Installation Instructions Graphic Driver Installation Instructions for Motherboard: EP-M845B, IP-4GVI63 and IP-4GVI20 for Intel Pentium 4 with Onboard Graphic for Operating Systems: Microsoft Windows NT 4.0, Windows 2000 and Windows

More information

Intel Rapid Storage Technology

Intel Rapid Storage Technology Intel Rapid Storage Technology User Guide August 2011 Revision 1.0 1 Document Number: XXXXXX INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,

More information

Intel Matrix Storage Console

Intel Matrix Storage Console Intel Matrix Storage Console Reference Content January 2010 Revision 1.0 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE,

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation... 2 1.1 Serial ATA (SATA) Hard Disks Installation... 2 2. Guide to RAID Configurations... 3 2.1 Introduction

More information

Intel Matrix Storage Manager 8.x

Intel Matrix Storage Manager 8.x Intel Matrix Storage Manager 8.x User's Manual January 2009 Revision 1.0 Document Number: XXXXXX INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,

More information

VIA / JMicron RAID Installation Guide

VIA / JMicron RAID Installation Guide VIA / JMicron RAID Installation Guide 1. Introduction to VIA / JMicron RAID Installation Guide. 3 2. VIA RAID Installation Guide. 3 2.1 VIA BIOS RAID Installation Guide.. 3 2.1.1 Introduction of RAID.

More information

ESATA PCI CARD. User s Manual

ESATA PCI CARD. User s Manual ESATA PCI CARD User s Manual Introduction... 3 System Requirements... 3 RAID Introduction... 3 BIOS Configuration Utility... 5 Configuring Arrays... 5 RAID Mode Definitions... 5 BIOS Configuration Utility...

More information

Chapter 2 Array Configuration [SATA Setup Utility] This chapter explains array configurations using this array controller.

Chapter 2 Array Configuration [SATA Setup Utility] This chapter explains array configurations using this array controller. Embedded MegaRAID SATA User's Guide Areas Covered Before Reading This Manual This section explains the notes for your safety and conventions used in this manual. Chapter 1 Overview This chapter introduces

More information

Configuring ThinkServer RAID 100 on the TS140 and TS440

Configuring ThinkServer RAID 100 on the TS140 and TS440 Configuring ThinkServer RAID 100 on the TS140 and TS440 Lenovo ThinkServer TS Series Servers Lenovo Enterprise Product Group Version 1.0 September 17, 2013 2013 Lenovo. All rights reserved. LENOVO PROVIDES

More information

SBI-7125B-T1 Blade Module RAID Setup Procedure

SBI-7125B-T1 Blade Module RAID Setup Procedure SBI-7125B-T1 Blade Module RAID Setup Procedure Revison 1.0 SBI-7125B-T1 Blade Module RAID Setup Procedure The information in this User s Manual has been carefully reviewed and is believed to be accurate.

More information

M5281/M5283. Serial ATA and Parallel ATA Host Controller. RAID BIOS/Driver/Utility Manual

M5281/M5283. Serial ATA and Parallel ATA Host Controller. RAID BIOS/Driver/Utility Manual Serial ATA and Parallel ATA Host Controller Rev. 0.96 December 03, 2003 Copyright 2003 ULi Electronics Inc. All rights reserved. COPYRIGHT NOTICE All information in this document is considered ULi Electronics

More information

Serial ATA RAID PCI. User's Manual

Serial ATA RAID PCI. User's Manual Serial ATA RAID PCI User's Manual Chapter 1 Introduction Table of Contents 1-1 Features and Benefits. 1 1-2 System Requirements. 1 Chapter 2 RAID Arrays 2-1 RAID Overview.. 2 2-1.1 RAID 0 (striping)...

More information

NVIDIA RAID Installation Guide

NVIDIA RAID Installation Guide NVIDIA RAID Installation Guide 1. NVIDIA BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID. 2 1.2 RAID Configurations Precautions.. 3 1.3 Create Disk Array. 4 2. NVIDIA Windows RAID Installation

More information

RAID Option Installation

RAID Option Installation RAID Option Installation Introduction RAID option is a PCI board including two HDD. The RAID option installation is carried out in 4 main phases: Pase A: Hardware installation Phase B: Configuration of

More information

RAID User Guide. Edition. Trademarks V1.0 P/N: 91-187C51GME0-00

RAID User Guide. Edition. Trademarks V1.0 P/N: 91-187C51GME0-00 RAID User Guide Edition V1.0 P/N: 91-187C51GME0-00 Trademarks All brand or product names mentioned are trademarks or registered trademarks of their respective holders. Contents NVIDIA RAID...1 RAID Arrays...1

More information

TL-PS310U Single USB 2.0 Port MFP and Storage Server

TL-PS310U Single USB 2.0 Port MFP and Storage Server TL-PS310U Single USB 2.0 Port MFP and Storage Server Rev: 2.0.0 1910010313 Contents Chapter 1 Introduction... 1 1.1 Product Overview...1 1.2 Network Management...1 1.3 Components and Features...1 1.4 Hardware

More information

Configuring ThinkServer RAID 100 on the Lenovo TS130

Configuring ThinkServer RAID 100 on the Lenovo TS130 Configuring ThinkServer RAID 100 on the Lenovo TS130 Contents Overview 02 Embedded RAID 100 features on TS130 02 RAID Overview 02 Choosing the RAID Level 02 RAID 0 02 RAID 1 03 Configuring RAID 03 BIOS

More information

Intel ESB2 SATA RAID Setup Guidelines

Intel ESB2 SATA RAID Setup Guidelines Intel ESB2 SATA RAID Setup Guidelines Intel ESB2 SATA RAID Setup Guidelines After all the hardware has been installed, you must first configure Intel ESB2 SATA RAID Settings before you install the Windows

More information

SATA RAID Function (Only for chipset Sil3132 used) User s Manual

SATA RAID Function (Only for chipset Sil3132 used) User s Manual SATA RAID Function (Only for chipset Sil3132 used) User s Manual 12ME-SI3132-001 Table of Contents 1 WELCOME...4 1.1 SATARAID5 FEATURES...4 2 AN INTRODUCTION TO RAID...5 2.1 DISK STRIPING (RAID 0)...5

More information

VIA RAID Installation Guide

VIA RAID Installation Guide VIA RAID Installation Guide 1 VIA BIOS RAID Installation Guide.... 3 1.1 Introduction of RAID... 3 1.2 RAID Configuration Precautions... 3 1.3 BIOS Configuration Utility.. 4 1.3.1 Enter BIOS Configuration

More information

RAID Manual. Edition. Trademarks V1.0 P/N: 91-187-CK8-A5-0E

RAID Manual. Edition. Trademarks V1.0 P/N: 91-187-CK8-A5-0E RAID Manual Edition V1.0 P/N: 91-187-CK8-A5-0E Trademarks All brand or product names mentioned are trademarks or registered trademarks of their respective holders. Contents NVIDIA RAID... 1 RAID Arrays...

More information

SSDNow For Desktops. Installation Guide

SSDNow For Desktops. Installation Guide Installation Guide Your purchase of the SSDNow with Accessory Kit will allow you to enjoy the benefits of increased system performance and reliability. All hardware and software necessary to replace your

More information

This user guide describes features that are common to most models. Some features may not be available on your computer.

This user guide describes features that are common to most models. Some features may not be available on your computer. RAID User Guide Copyright 2011 Hewlett-Packard Development Company, L.P. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft and Windows are U.S. registered trademarks

More information

SiS S-ATA User s Manual. Quick User s Guide. Version 0.1

SiS S-ATA User s Manual. Quick User s Guide. Version 0.1 SiS S-ATA User s Manual Quick User s Guide Version 0.1 Edition April 2003 Copyright Trademarks SiS is a registered trademark of Silicon Integrated Systems Corp. All brand or product names mentioned are

More information

RocketStor SMART RAID

RocketStor SMART RAID RocketStor SMART RAID User Guide v1.0 1 Copyright HighPoint Technologies Inc., 1995-2012. All rights reserved. OS X and Macintosh are registered trademarks of Apple Corporation. All other trademarks and

More information

4 Channel 6-Port SATA 6Gb/s PCIe RAID Host Card

4 Channel 6-Port SATA 6Gb/s PCIe RAID Host Card 4 Channel 6-Port SATA 6Gb/s PCIe RAID Host Card User Manual Model: UGT-ST644R All brand names and trademarks are properties of their respective owners www.vantecusa.com Contents: Chapter 1: Introduction...

More information

Taurus Super-S3 LCM. Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives. User Manual March 31, 2014 v1.2 www.akitio.

Taurus Super-S3 LCM. Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives. User Manual March 31, 2014 v1.2 www.akitio. Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives User Manual March 31, 2014 v1.2 www.akitio.com EN Table of Contents Table of Contents 1 Introduction... 1 1.1 Technical Specifications...

More information

RAID installation guide

RAID installation guide RAID installation guide V1.0 Date : 2009-06-29 TWINHEAD INTERNATIONAL CORP. 10F, 550 Rueiguang Road Neihu, Taipei, Taiwan 114,ROC. TEL(886)2 5589 9999 FAX (886) 2 5555 7777 Enabling RAID in BIOS Perform

More information

MaxAttach NAS 4000 Series OS 2.2 Hard Disk Drive Replacement

MaxAttach NAS 4000 Series OS 2.2 Hard Disk Drive Replacement MaxAttach NAS 4000 Series MaxAttach NAS 4000 Series OS 2.2 Hard Disk Drive Replacement DOCUMENT OVERVIEW Who Should Use This Instruction Set This MaxAttach NAS 4000 Series by Maxtor HDD Replacement Instruction

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation... 2 1.1 Serial ATA (SATA) Hard Disks Installation... 2 2. Guide to RAID Configurations... 3 2.1 Introduction

More information

USB 2.0 VGA ADAPTER USER MANUAL

USB 2.0 VGA ADAPTER USER MANUAL USB 2.0 VGA ADAPTER USER MANUAL CONTENTS INTRODUCTION... 3 FEATURES... 3 SYSTEM REQUIREMENTS... 3 PACKAGE CONTENTS... 3 SUPPORTED COMMON DISPLAY RESOLUTION... 4 TECHNICAL SPECIFICATIONS... 4 INSTALLATION

More information

This user guide describes features that are common to most models. Some features may not be available on your computer.

This user guide describes features that are common to most models. Some features may not be available on your computer. RAID User Guide Copyright 2009 Hewlett-Packard Development Company, L.P. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft, Windows, and Windows Vista are U.S. registered

More information

AMD RAID Installation Guide

AMD RAID Installation Guide AMD RAID Installation Guide 1. AMD BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID.. 2 1.2 RAID Configurations Precautions 3 1.3 Installing Windows XP / XP 64-bit / Vista / Vista 64-bit With

More information

SiS 180 S-ATA User s Manual. Quick User s Guide. Version 0.1

SiS 180 S-ATA User s Manual. Quick User s Guide. Version 0.1 SiS 180 S-ATA User s Manual Quick User s Guide Version 0.1 Edition April 2003 Copyright Trademarks SiS is a registered trademark of Silicon Integrated Systems Corp. All brand or product names mentioned

More information

Portable HDD Duplicator

Portable HDD Duplicator Portable HDD Duplicator User Manual SH-PHD shintaro.com.au Portable HDD Duplicator Contents 2.5 /3.5 SATA HDD Connection Diagram 4 Features /Operating System 6 Package Contents / Button Functions 6 System

More information

SATA RAID SIL 3112 CONTROLLER USER S MANUAL

SATA RAID SIL 3112 CONTROLLER USER S MANUAL SATA RAID SIL 3112 CONTROLLER USER S MANUAL 120410056E1N Copyright Copyright 2003. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system

More information

SATA+Ultra ATA RAID CONTROLLER RC212. User Manual

SATA+Ultra ATA RAID CONTROLLER RC212. User Manual SATA+Ultra ATA RAID CONTROLLER RC212 Contents Feature and benefits Package contents System requirement Magic Switch introduction and jumper setting Hardware installation Important message for user RAID

More information

SATA1.5G/ATA133 RAID Controller Card RC215 User Manual

SATA1.5G/ATA133 RAID Controller Card RC215 User Manual SATA1.5G/ATA133 RAID Controller Card RC215 Features and Benefits Compliant with Serial ATA 1.0 specification Compliant with PCI Specification, revision 2.2 Provides three independent channels to connect

More information

Addonics. 4-Port External SATA II PCI/PCI-X RAID5 Controller Card (ADS3GX4R5-E) User s Guide Revision 1.1 T E C H N O L O G I E S

Addonics. 4-Port External SATA II PCI/PCI-X RAID5 Controller Card (ADS3GX4R5-E) User s Guide Revision 1.1 T E C H N O L O G I E S Addonics T E C H N O L O G I E S 4-Port External SATA II PCI/PCI-X RAID5 Controller Card (ADS3GX4R5-E) User s Guide Revision 1.1 FCC Warning Statement This equipment has been tested and found to comply

More information

IEEE 802.11b WLAN PC Card

IEEE 802.11b WLAN PC Card IEEE 802.11b WLAN PC Card User s Guide Version: 1.3 August 2001 Please install the Utility/Driver first before inserting the PCMCIA Card. FCC Class B Radio Frequency Interference Statement The manufacturer

More information

2 Bay USB 3.0 RAID 3.5in HDD Enclosure

2 Bay USB 3.0 RAID 3.5in HDD Enclosure 2 Bay USB 3.0 RAID 3.5in HDD Enclosure SAT3520U3SR *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com

More information

The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled systems.

The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled systems. SATA II PCIe RAID Quick Installation Guide Introducing the SATA II PCIe RAID The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled

More information

HP dx5150 RAID Installation and Setup Guide Version 1.10. Document Part Number: 403571-001

HP dx5150 RAID Installation and Setup Guide Version 1.10. Document Part Number: 403571-001 HP dx5150 RAID Installation and Setup Guide Version 1.10 Document Part Number: 403571-001 July 2005 Copyright 2005 Hewlett-Packard Development Company, L.P. The information contained herein is subject

More information

XL-RAID-SATA2-USB. User Manual. v.1.2 (January, 2010)

XL-RAID-SATA2-USB. User Manual. v.1.2 (January, 2010) XL-RAID-SATA2-USB User Manual v.1.2 (January, 2010) With regard to this manual Thank you for using the product of Xtendlan Technology Inc. This manual will introduce XTENDLAN XL-RAID-SATA2-USB. Before

More information

AMD RAID Installation Guide

AMD RAID Installation Guide AMD RAID Installation Guide 1. AMD BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID.. 2 1.2 RAID Configurations Precautions 3 1.3 Installing Windows 7 / 7 64-bit / Vista / Vista 64-bit / XP /

More information

This user guide describes features that are common to most models. Some features may not be available on your computer.

This user guide describes features that are common to most models. Some features may not be available on your computer. RAID User Guide Copyright 2011 Hewlett-Packard Development Company, L.P. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft, Windows, and Windows Vista are U.S. registered

More information

RAID installation guide for Silicon Image SiI3114

RAID installation guide for Silicon Image SiI3114 RAID installation guide for Silicon Image SiI3114 Contents Contents 2 1 Introduction 4 1.1 About this Guide 4 1.2 The Basics 4 1.2.1 What is RAID? 4 1.2.2 Advantages of RAID 4 1.2.3 Disadvantages of RAID

More information

Shutting down / Rebooting Small Business Server 2003 Version 1.00

Shutting down / Rebooting Small Business Server 2003 Version 1.00 Shutting down / Rebooting Small Business Server 2003 Version 1.00 Need to Know TM It may be necessary at some stage of the life of Small Business Server 2003 that it be shutdown or rebooted. In many cases

More information

Areas Covered. Chapter 1 Features (Overview/Note) Chapter 2 How to Use WebBIOS. Chapter 3 Installing Global Array Manager (GAM)

Areas Covered. Chapter 1 Features (Overview/Note) Chapter 2 How to Use WebBIOS. Chapter 3 Installing Global Array Manager (GAM) PRIMERGY RX300 S2 Onboard SCSI RAID User s Guide Areas Covered Chapter 1 Features (Overview/Note) This chapter explains the overview of the disk array and features of the SCSI array controller. Chapter

More information

ReturnStar HDD Lock V3.0 User Manual

ReturnStar HDD Lock V3.0 User Manual ReturnStar HDD Lock V3.0 User Manual Copyright(C) 2003-2007 Returnstar Electronic Information Co., Ltd. Web: http://www.recoverystar.com Tel: +86-591-83385086 87274373 Fax: +86-591-87274383 E-mail: master@recoverystar.com

More information

**Please read this manual carefully before you use the product**

**Please read this manual carefully before you use the product** -1- **Please read this manual carefully before you use the product** Description: The CEB-2355S is a multifunction storage device designed in a special body structure, which can be simply connected to

More information

SiS964 RAID. User s Manual. Edition. Trademarks V1.0 P/N: 91-187-U49-M2-0E

SiS964 RAID. User s Manual. Edition. Trademarks V1.0 P/N: 91-187-U49-M2-0E SiS964 RAID User s Manual Edition V1.0 P/N: 91-187-U49-M2-0E Trademarks All brand or product names mentioned are trademarks or registered trademarks of their respective holders. CONTENTS Introduction...

More information

RAID configuration and driver installation guide

RAID configuration and driver installation guide Server systems and motherboards RAID configuration and driver installation guide For AP130-E1 5U Rackmount Server AP1720-E2 5U Rackmount Server NCCH-DL Motherboard PSCH-L Motherboard E1600 First edition

More information

AMD RAID Installation Guide

AMD RAID Installation Guide AMD RAID Installation Guide 1. AMD BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID.. 2 1.2 RAID Configurations Precautions 3 1.3 Installing Windows 8 / 8 64-bit / 7 / 7 64-bit / Vista TM / Vista

More information

PCI Express SATA Controller Card

PCI Express SATA Controller Card PEXSAT31E1 Instruction Manual PCI Express SATA Controller Card 1-Port esata, 1-Port SATA PCI Express SATA 6Gbps Controller Card FCC Compliance Statement This equipment has been tested and found to comply

More information

To configure SATA hard drive(s), follow the steps below:

To configure SATA hard drive(s), follow the steps below: 4-1-4 Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS

More information

2.5/3.5 SATA HDD Docking Station

2.5/3.5 SATA HDD Docking Station SATADOCKU2 SATADOCKU2E SATADOCK22UE 2.5/3.5 SATA HDD Docking Station FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

More information

VIA RAID Installation Guide

VIA RAID Installation Guide VIA RAID Installation Guide 1 VIA BIOS RAID Installation Guide.... 3 1.1 Introduction of RAID... 3 1.2 RAID Configuration Precautions... 3 1.3 Installing Windows 2000 / XP / Vista With RAID Functions..

More information

SATA II 4 Port PCI RAID Card RC217 User Manual

SATA II 4 Port PCI RAID Card RC217 User Manual SATA II 4 Port PCI RAID Card RC217 SATA II 4 Port PCI RAID Card This Manual is for many Models of SATAII RAID5 HBA that uses Silicon Image SATA II SiI3124 chipset: 1) 32bit PCI bus host card 2) 64bit PCI-X

More information

USB2VGA. Instruction Manual. USB to VGA Adapter. USB 2.0 to VGA External Multi Monitor Video Adapter

USB2VGA. Instruction Manual. USB to VGA Adapter. USB 2.0 to VGA External Multi Monitor Video Adapter USB to VGA Adapter USB2VGA Instruction Manual USB 2.0 to VGA External Multi Monitor Video Adapter FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class

More information

RAID installation guide for ITE8212F

RAID installation guide for ITE8212F RAID installation guide for ITE8212F Contents Contents 2 1 Introduction 3 1.1 About this Guide 3 1.2 The Basics 3 1.2.1 What is RAID? 3 1.2.2 Advantages of RAID 3 1.2.3 Disadvantages of RAID 3 1.3 Different

More information

IDE ATA/133 Controller

IDE ATA/133 Controller IDE ATA/133 Controller 2 Port PCI ATA-133 IDE Adapter Card PCIIDE2 Actual product may vary from photo FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class

More information

Serial ATA RAID PCI Card

Serial ATA RAID PCI Card Serial ATA RAID PCI Card User Manual 1 Features Silicon Image SiI3512 SATA controller chip Compliant with PCI Specification, Rev. 2.3 Compliant with Serial ATA 1.0 specification Provides two independent

More information

VAIO Computer Recovery Options Guide

VAIO Computer Recovery Options Guide VAIO Computer Recovery Options Guide This guide provides information about restoring individual software programs, software drivers, drive partition(s), or the hard disk drive to the original factory settings.

More information

VT8237 SATA RAID User Manual

VT8237 SATA RAID User Manual VT8237 SATA RAID User Manual Enter BIOS Configuration Utility When the system powers on, the following information will appear on screen. Press the Tab key to enter BIOS configuration utility. 39 VIA Technologies,Inc.VIA

More information

User s Manual. Home CR-H212. 2.5 2-BAY RAID Storage Enclosure

User s Manual. Home CR-H212. 2.5 2-BAY RAID Storage Enclosure User s Manual Home CR-H212 2.5 2-BAY RAID Storage Enclosure 1 Introduction 1.1 Features - 2-Bay Bus Powered Portable RAID Enclosure -Works with SATA HDD or SSD -Supports Big (JBOD), RAID0, RAID1, and Normal

More information

Marvell SATA3 RAID Installation Guide

Marvell SATA3 RAID Installation Guide Marvell SATA3 RAID Installation Guide Overview The Marvell RAID Utility (MRU) is a browser-based graphical user interface (GUI) tool for the Marvell RAID adapter. It supports IO Controllers (IOC) and RAID-On-Chip

More information

PCIe SATA 6G Raid Card

PCIe SATA 6G Raid Card PCIe SATA 6G Raid Card User Manual Ver. 1.00 All brand names and trademarks are properties of their respective owners. Contents: Chapter 1: Introduction... 3 1.1 Product Introduction... 3 1.2 Features...

More information

RAID1 rebuild procedure for Intel Matrix Storage Manager

RAID1 rebuild procedure for Intel Matrix Storage Manager RAID1 rebuild procedure for Intel Matrix Storage Manager Document number GD-2012-0022-A Date: March 9, 2012 Written by: Distribution: Torleif Ringsaker, Tordivel AS Public 1 Introduction RAID1 is a drive

More information

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3 SiS964/SiS180 SATA w/ RAID User s Manual Quick User s Guide Version 0.3 Edition December 2003 Copyright 2003 Silicon Integrated Systems Corp. Trademarks SiS is a registered trademark of Silicon Integrated

More information

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3 SiS964/SiS180 SATA w/ RAID User s Manual Quick User s Guide Version 0.3 Edition December 2003 Copyright 2003 Silicon Integrated Systems Corp. Trademarks SiS is a registered trademark of Silicon Integrated

More information

GENERAL INFORMATION COPYRIGHT... 3 NOTICES... 3 XD5 PRECAUTIONS... 3 INTRODUCTION... 4 FEATURES... 4 SYSTEM REQUIREMENT... 4

GENERAL INFORMATION COPYRIGHT... 3 NOTICES... 3 XD5 PRECAUTIONS... 3 INTRODUCTION... 4 FEATURES... 4 SYSTEM REQUIREMENT... 4 1 Table of Contents GENERAL INFORMATION COPYRIGHT... 3 NOTICES... 3 XD5 PRECAUTIONS... 3 INTRODUCTION... 4 FEATURES... 4 SYSTEM REQUIREMENT... 4 XD5 FAMILULARIZATION... 5 PACKAGE CONTENTS... 5 HARDWARE

More information

5-Bay Raid Sub-System Smart Removable 3.5" SATA Multiple Bay Data Storage Device User's Manual

5-Bay Raid Sub-System Smart Removable 3.5 SATA Multiple Bay Data Storage Device User's Manual 5-Bay Raid Sub-System Smart Removable 3.5" SATA Multiple Bay Data Storage Device User's Manual www.vipower.com Table of Contents 1. How the SteelVine (VPMP-75511R/VPMA-75511R) Operates... 1 1-1 SteelVine

More information

PCI Express SATA / esata 6Gb/s RAID Card User Manual

PCI Express SATA / esata 6Gb/s RAID Card User Manual PCI Express SATA / esata 6Gb/s RAID Card User Manual Specifications : - 2 x SATA 6Gb/s Port (SATA version) - 2 x esata 6Gb/s Port (esata version) - Max. 6Gb/s transfer rate per port - Supports both SATA

More information

Brake module AX5021. Documentation. Please read this document carefully before installing and commissioning the brake module!

Brake module AX5021. Documentation. Please read this document carefully before installing and commissioning the brake module! Documentation Brake module AX5021 Please read this document carefully before installing and commissioning the brake module! Version : 1.2 : 2012.03.05 Date Article-no. : TDmlAX-5021-0000-0200 Page 2/8

More information

AMD SP5100 Dot Hill SATA RAID Users Manual V100

AMD SP5100 Dot Hill SATA RAID Users Manual V100 AMD SP5100 Dot Hill SATA RAID Users Manual V100 1 Table of Contents Section 1 Dot Hill Firmware Overview Firmware Overview Page 3 Firmware Option Rom/Firmware Overview Page 3 Firmware Menus Page 4 Initialize

More information

Intel RAID Volume Recovery Procedures

Intel RAID Volume Recovery Procedures Intel RAID Volume Recovery Procedures Revision 1.0 12/20/01 Revision History Date Revision Number 12/20/01 1.0 Release Modifications Disclaimers Information in this document is provided in connection with

More information

USER S MANUAL. www.vantecusa.com

USER S MANUAL. www.vantecusa.com USER S MANUAL www.vantecusa.com Package Contents: Dual 3.5 RAID Enclosure w/fan USB 3.0 & esata Interface 1 NexStar MX 2 USB 3.0 Cable 3 esata Cable 4 Power Adapter 5 User s Manual 6 Enclosure Stand 7

More information

Dual/Quad 3.5 SATA to USB 3.0 & esata External Hard Drive RAID/Non-RAID Enclosure w/fan. User s Manual

Dual/Quad 3.5 SATA to USB 3.0 & esata External Hard Drive RAID/Non-RAID Enclosure w/fan. User s Manual Dual/Quad 3.5 SATA to USB 3.0 & esata External Hard Drive RAID/Non-RAID Enclosure w/fan User s Manual Package Contents: NextStar HX4/HX4R NextStar HX2R 1 2 1 2 3 4 3 4 5 6 5 6 7 1 NexStar HX4R/HX4 2 USB

More information

Encore SATA2 RAID PCIe Card

Encore SATA2 RAID PCIe Card Encore SATA2 RAID PCIe Card User Manual Ver. 2.00 All brand names and trademarks are properties of their Respective owners. 1 Features and Benefits Compliant with PCI Express Base Specification 1.0a Compliant

More information

Ultra ATA 133 RAID PCI Pro

Ultra ATA 133 RAID PCI Pro Ultra ATA 133 RAID PCI Pro 1-1 Introduction Quick Installation Guide This ultra high-speed dual channel Ultra ATA/133 RAID controller is designed to support RAID 0, 1, 0+1 and JBOD. RAID configurations

More information

USB to VGA Adapter USB2VGAE2. Instruction Manual. USB 2.0 to VGA Multi Monitor External Video Adapter

USB to VGA Adapter USB2VGAE2. Instruction Manual. USB 2.0 to VGA Multi Monitor External Video Adapter USB to VGA Adapter USB2VGAE2 Instruction Manual USB 2.0 to VGA Multi Monitor External Video Adapter *Please ensure that the driver installation is complete prior to the physical installation of the USB

More information

SATARAID5 Serial ATA RAID5 Management Software

SATARAID5 Serial ATA RAID5 Management Software SATARAID5 Serial ATA RAID5 Management Software Home Edition Preliminary Draft Subject to Change Without Notice 05/7/04 Silicon Image, Inc. 1060 East Arques Ave. Sunnyvale CA 94085 (408) 616-4000 www.siliconimage.com

More information

USB Flash Drive User s Manual

USB Flash Drive User s Manual USB Flash Drive User s Manual V4.01 Introduction Thank you for your purchasing the USB Drive. This manual will guide you through the usages of the USB Drive and of all management tools coming with it.

More information

Wireless AC600 Dual-Band USB Adapter

Wireless AC600 Dual-Band USB Adapter Model 202043 Supports Windows XP/Vista/7/8/8.1/10 Dual-Band 2.4 GHz / 5 GHz Peak Transfer rate up to 150 / 433 Mbps WPS - Wi-Fi Protected One-Button Setup WEP/WPA/WPA2 Security Support Green LED Power

More information

SATA II-150 PCI RAID

SATA II-150 PCI RAID SATA II-150 PCI RAID Quick Installation Guide Introducing the SATA II-150 PCI RAID The SATA II-150 PCI RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI enabled

More information

2» 10» 18» 26» PD3 34 00 42»

2» 10» 18» 26» PD3 34 00 42» » STARDOM Safe Capsule Series User Manual... 2» STARDOM Safe Capsule Serie Bedienungsanleitung... 10» Série STARDOM Safe Capsule Manuel de l utilisateur... 18 26 PD3500 34» Manual de usuario de STARDOM

More information

SATA PCI Express Adapter PEXSATA22I

SATA PCI Express Adapter PEXSATA22I SATA PCI Express Adapter PEXSATA22I FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

More information

2-Bay Raid Sub-System Smart Removable 3.5" SATA Multiple Bay Data Storage Device User's Manual

2-Bay Raid Sub-System Smart Removable 3.5 SATA Multiple Bay Data Storage Device User's Manual 2-Bay Raid Sub-System Smart Removable 3.5" SATA Multiple Bay Data Storage Device User's Manual www.vipower.com Table of Contents 1. How the SteelVine (VPMP-75211R/VPMA-75211R) Operates... 1 1-1 SteelVine

More information

Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines

Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines After all hardware has been installed, you must fi rst confi gure the Intel SATA HostRAID settings

More information

Serial ATA 4-Channel RAID Quick Installation Guide

Serial ATA 4-Channel RAID Quick Installation Guide Serial ATA 4-Channel RAID Quick Installation Guide Introducing the Serial ATA 4-Channel RAID The Serial ATA 4-Channel RAID is an ultra high-speed four channel Serial ATA controller for use in Pentium class

More information

Using GIGABYTE Notebook for the First Time

Using GIGABYTE Notebook for the First Time P34 V6.0 Congratulations on your purchase of the GIGABYTE Notebook. This manual will help you to get started with setting up your notebook. The final product configuration depends on the model at the point

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation...2 1.1 Serial ATA (SATA) Hard Disks Installation...2 2. Guide to RAID Configurations...3 2.1 Introduction

More information

P/N: ST0014U. Hard Drive not included*

P/N: ST0014U. Hard Drive not included* P/N: ST0014U Hard Drive not included* Hardware Installation: 1. TOP View 2. Disk Installation Hard Drive not included* Introduction: Thermaltake BlacX Duet esata & USB Docking Station easily connects all

More information

Rebuilding a Show Store RAID with the original drives

Rebuilding a Show Store RAID with the original drives Rebuilding a Show Store RAID with the original drives It is important to note that if a drive fails in the Show Store RAID, it does not necessarily mean that the drive is faulty. In the vast majority of

More information

This chapter explains how to update device drivers and apply hotfix.

This chapter explains how to update device drivers and apply hotfix. MegaRAID SAS User's Guide Areas Covered Before Reading This Manual This section explains the notes for your safety and conventions used in this manual. Chapter 1 Overview This chapter explains an overview

More information

Promise FastTrak 100-Lite RAID Controller

Promise FastTrak 100-Lite RAID Controller Promise FastTrak 100-Lite RAID Controller User s Manual Version 1.3, November 9, 2001 Copyright Copyright by Promise Technology, Inc. ( Promise ), XP. No part of this manual may be reproduced or transmitted

More information

Automation License Manager

Automation License Manager s Contents Product Overview 1 Installation 2 Working with the Automation License Manager 3 Glossary Manual Index 12/2008 A5E02389428-01 Legal information Warning notice system This manual contains notices

More information

How to Install Microsoft Windows Server 2008 R2 in VMware ESXi

How to Install Microsoft Windows Server 2008 R2 in VMware ESXi How to Install Microsoft Windows Server 2008 R2 in VMware ESXi I am not responsible for your actions or their outcomes, in any way, while reading and/or implementing this tutorial. I will not provide support

More information

esata 6G RAID PCIe 2.0 Controller Card

esata 6G RAID PCIe 2.0 Controller Card esata 6G RAID PCIe 2.0 Controller Card User Manual Table of Contents Part 1: Introduction Page 3 a. Overview Page 3 b. MAXPower esata 6G RAID Features Page 3 c. What is esata 6Gb/s? Page 3 d. What is RAID?

More information