1.1 DOOR'S SYSTEM INTRODUCTION - IRIZAR'S I6 DOOR SYSTEM

Size: px
Start display at page:

Download "1.1 DOOR'S SYSTEM 1.1.1 INTRODUCTION - IRIZAR'S I6 DOOR SYSTEM"

Transcription

1 Door's adjustment

2 1.1 DOOR'S SYSTEM INTRODUCTION - IRIZAR'S I6 DOOR SYSTEM The vehicle's door system is designed to open and close during normal and emergency operation. As being an electro-pneumatic system, it possess a sensibilization system, which is capable of avoiding any accident during the process of closure and opening. The pneumatic system has a lubrication and protection system with a separation valve between the chassis and body. This valve can be used for leaking diagnoses or air removal during the door's system maintenance process. The i6 door's system has the structure protected by aluminium plates. Isolating agents are also applied in the interior, to provide thermal and acoustic isolation. The sealing system is composed by a solid rubber, with no junctions on the edges or over the doorstop. Door's rubber shape Doorstop shape DOOR'S SENSIBILIZATION SYSTEM The door's sensibilization system operates during the opening and closure of the door. During the closure the system operates when the electric system possess the +30 line, in other words, the main switch must be on. To opening, the system operates permanently, even when the +30 line isn't working, disconnected main switch. During the closure process, the micro-switches system acts under the door's solenoid, reverting the movement, in case of any obstacle interrupt the door's movement. During the opening process, the door has its movement protected, avoiding any collision with adjacents components, such as compartment cover. 2

3 Picture 1 - Sensibilization during closure Picture 2 - Adjacent compartment blocking the door from opening It is possible to adjust the performance of the sensibilization system by adjusting the aluminium cam. This cam turns with the door's movement, providing the protection during the closure. There are two micro-switches connected, on vertical and the other horizontal. When the cam reaches the horizontal micro-switch (at the end of the door's course), the cam disables the vertical micro-switch, canceling the sensibilization. In case of an obstacle during the closure, the cam won't reach the horizontal micro-switch. The force imposition against the closure makes the door to initiate a vertical movement. The movement elevates the plastic part, in shape of half moon, activating the micro-switch that sends an electric signal to the door's valve so the movement of closure is reversed, therefore openning the door. Cam Half moon Micro-switch horizontal Micro-switch horizontal Micro-switch Vertical Picture 3 - Door's sensibilization This way, the cam's position is related to the door's position, in order to provide the door's sensibilization. 3

4 1.1.3 DOOR SYSTEM ADJUSTMENT The vehicle's door must be considered misfit when: Presents excessive noise; Does not close adequately and allows water entrance and air seal problems ar; Presents problems while opening or closing; Time demanded to open or close is excessive; Open or close just with external help; Doesn't present sensibility to obstacles while closing. Mechanical adjustment points Doors system Door's upper bearing Arm's conection Door's bottom bearing Bottom bearing Door's guide rod Wedge 4

5 1.1.4 DOOR MOVEMENT Movements Function Illustration Parallel to the body. Propitiate seal during the correct closure. Perpendicular to the body. Propitiate seal and correct closure. Vertical This movement is responsible for fixing the door in the doorstop, conferring rigidity and seal DOOR ADJUSTMENT PARAMETERS parameter Function Illustration Geometric positioning The geometric positioning is related with the alignment of the door to with the doorstop, as shown on the right. This parameter is controlled by the wedge set and the positioning of the door's fixation bearing, both internal and external. Sealing The door's sealing is of extreme importance to avoid water entrances, dust and even noises originated by the air entrance. The superior wedge's set is responsible for bringing the door closer to the body, complementing the perpendicular movement. The 5

6 set of inferior wedges limits the vertical movement Seal and also seals the door. Excessive seal implicates in high forces applied to the wedges, which reduces it's lifetime and may cause damage to the door's doorstop. It's possible to obtain good seal when the door's surface is aligned with the body's surface. Parallelism with the body Open the door This parameter is defined through the guide arm, situated in the door's inferior part. The lenght of the guide arm defines the position in which the door will touch the doorstop during the door's perpendicular movement. The door's approximation with the doorstop must be parallel, and both sides must touch the doorstop at the moment of closure. The door must be aligned with the body's lateral lines, doorstop and with the doorstop's inferior part. This can be obtained through the adjustment of the inferior wedges. Guide arm Centralization The existent cracks between the doorstop and the door must approach on both sides equally. This parameter can be reached when combining all the factors mentioned before. Velocity of closure The complete movements of opening and closure must be concluded in 4 to 6 seconds. Faster movements might damage the trigger, doorstop and the door's structure. 6

7 20 mm 2 to 4 mm Instrução Técnica Instrucción Técnica Technical Instruction Closur e Ope ning The doors closure force The doors closure force must be set to attend the operational necessity. For example, if the car stops on a descent roadside, the force applied to close the door is bigger. Wedge's positioning The standard approximation between the wedge set must be within 2 to 4 mm. Door's external bearing adjustment The minimum distance between the nut and the locknut is of 20mm DOOR'S SENSIBILIZATION SYSTEM The opened door signal is generated by an horizontal microswitch, as picture 3-Door sensibilization. This opened door signal also send an electric signal to the green pilots of the retractable step. This way, when the cam touches the horizontal micro-switches, the green pilots of the retractable steps turns off. 7

8 Opened door, cam does not touch the microswitch, stair's illumination is activated. Half open door with a clearance of 50mm, notice that the cam doesn't touches the micro-switch, so the stair's illumination isn't activated. 50mm 8

9 The cam's correct positioning must have as reference the centerline of its fixation screws and the door's surface. The artifice above can be used to adjust the cam's positioning. 90 graus Picture 4 - Cam's positioning diagram To adjust the cam's position, release the Allen screw, then turn it to the right position. Screw Picture 5 - Allen screw positioning 9

10 1.1.7 DOOR'S SYSTEM PREVENTIVE MAINTENANCE Table of preventive maintenance - Door Action Frequency Standard value Check the contact of the wedge's screws. Every month 20 N.M Check the M10 screw's torque ( bar, actuator support, guide arm ) Every month 40 N.M Check the M14 screw's torque ( tension rod ) Every month 80 N.M Check the torque of the M16 screw thread ( torsion bar ) Every month 125 N.M Check the torque of the M16 screw thread Every month 125 N.M 10

11 Check the door's sensibilization system Every week 150N, an adult must prevent the door from closing, activating the sensibility system TIPS OF IRIZA'S AFTERSALE STAFF. Description Tips Illustration Door does not close aligned, problems with geometrical alignment. Misalignment usually might be caused by incorrect coupling of the wedges. This effect can be observed by lifting of the door's rubber after closed. Another possibility is the incorrect adjustment of the door's fixation rod. Incorrect coupling In case of geometric misalignment, an adjust of the door's fixation wedges might help. To adjust the external bearing, just release them, and then use a rubber hammer to adjust its positioning. Upper bearing adjustment 11

12 The door's edge first touches the doorstop, the wedges might not fit correctly. To avoid these problems, the guide arm must be adjusted correctly. There are two possibilities of adjustment: The first it's own lenght through the screws in the body; Another possibility is through the guide's fixation screws on the body with the holes, as shown on the right. With the door closed, it is possible to notice noises of air entrance on the door's bottom part, when the car is moving. In some cases, the door's rod is misaligned, creating a gap at the door's bottom part. The procedure to adjust the door's height can be executed by releasing the screws, indicated on the left. Using a rubber hammer, the arm's position can be modified with soft hits. Attention: Never release the fixation of both arms at the same time. BRAÇ O 2 BRAÇ O 1 12

13 During closing, the door slams against the doorstop and doesn't align the wedge's set correctly. During the process of adjustment, use the emergency valve to keep the door loose. This makes the procedure easier, because it's not necessary to use the service valve to remove the body's air when a test is necessary. In this case, adjust the door's final course speed. The movements of opening and closure must be concluded within 4 to 6 seconds. Faster movements might damage the wedge's set, doorstop and door's structure. The movement's speed might be adjusted through the valves in the actuator cylinder, as indicated on the left. - Course end ( closure ) Course end ( opening ) 13

Workshop Manual. English REVISION 0 FORMAT Nº 151 14.05.2009

Workshop Manual. English REVISION 0 FORMAT Nº 151 14.05.2009 Workshop Manual PB English REVISION 0 FORMAT Nº 151 14.05.2009 Irizar PB WorkShop Manual INDEX HEADLIGHT SET OPENING AND LAMPS REPLACE 5 1 HEADLIGHT SET OPENING AND LAMPS REPLACE 7 FRONT, CENTRAL AND

More information

MEASURING WHEEL ALIGNMENT

MEASURING WHEEL ALIGNMENT MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel

More information

SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE

SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic

More information

Master Code 2. Troubleshooting: Installation 7. Troubleshooting: Door Jamming and Door Handing 8. Troubleshooting: Keypad 12

Master Code 2. Troubleshooting: Installation 7. Troubleshooting: Door Jamming and Door Handing 8. Troubleshooting: Keypad 12 Programming and Troubleshooting Guide 1 2 3 4 5 6 Master Code 2 Troubleshooting: Installation 7 Troubleshooting: Door Jamming and Door Handing 8 Troubleshooting: Keypad 12 Troubleshooting: Battery 13 Battery

More information

Unit 24: Applications of Pneumatics and Hydraulics

Unit 24: Applications of Pneumatics and Hydraulics Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 2 HYDRAULIC AND PNEUMATIC CYLINDERS The material needed for outcome 2 is very extensive

More information

2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure

2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure 2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure Derek Guenther 1/28/2015 Rev. Purpose The purpose of this document is to describe the procedure necessary to replace one of the ball nuts

More information

Sliding Door Hardware Installation Instructions

Sliding Door Hardware Installation Instructions Sliding Door Hardware Installation Instructions Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview ff All Krown Lab sliding

More information

1993 SUSPENSION Volkswagen Front. EuroVan

1993 SUSPENSION Volkswagen Front. EuroVan Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Front EuroVan DESCRIPTION FWD independent suspension is an double-wishbone type with torsion bars mounted on upper control arm. Wheel is supported

More information

Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN

Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview

More information

Operation of the overrun braking system.

Operation of the overrun braking system. Operation of the overrun braking system. Fig 1 The overrun device can be described as the control device of the overrun brake system. A draw-bar force is produced at the coupling point by reducing the

More information

Experience In Motion. Valtek Spring Cylinder Linear Actuators

Experience In Motion. Valtek Spring Cylinder Linear Actuators Experience In Motion Valtek Spring Cylinder Linear Actuators Valtek Spring Cylinder Linear Actuator Flowserve spring cylinder linear actuators are powerful, compact, high-performance pneumatic actuators

More information

Custom configuration such as modified angle dimensions, other flange standards, 3-way function, alternative materials.are available on request.

Custom configuration such as modified angle dimensions, other flange standards, 3-way function, alternative materials.are available on request. LEAKVALVE: HIGHLIGHTS The core of this valve is a diaphragm in stainless steel 316L, gold plated. Robust, it cannot be damaged with any normal methods. The dead volume is kept as small as possible. There

More information

OWNER S MANUAL. Permolock C3. Docking system for Power wheelchair in vehicle

OWNER S MANUAL. Permolock C3. Docking system for Power wheelchair in vehicle OWNER S MANUAL US Permolock C3 Docking system for Power wheelchair in vehicle How to contact Permobil Head Office of the Permobil group Permolock C3 Docking system for electric wheelchair in vehicle Produced

More information

Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors

Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 20000 Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 823 Notes 824 Technical

More information

SELF-STEERING AXLE TABLE OF CONTENTS

SELF-STEERING AXLE TABLE OF CONTENTS SELF-STEERING AXLE TABLE OF CONTENTS Section 1 - Introduction Section 2 - Pre-Installation Check List Section 3 - Ride Height Adjustments Section 4 - Suspension Mount Section 5 - Axle Mount Section 6 -

More information

Front axle components, overview

Front axle components, overview just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,

More information

Drive shaft, servicing

Drive shaft, servicing Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,

More information

39HQ Airovision Air Handling Units

39HQ Airovision Air Handling Units 39HQ Airovision Air Handling Units Mounting instructions CONTENTS 1 - TRANSPORT AND LIFTING INSTRUCTIONS... 3 1.1 - General... 3 1.2 - Transport and storage... 3 1.3 - Roof edge protection during transport

More information

ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions

ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions 4057250/8 IM-P405-16 AB Issue 8 ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Operation

More information

INSTRUCTION MANUAL HYDRAULIC GATE TRANSMISSION SYSTEM ECO240-ECO360

INSTRUCTION MANUAL HYDRAULIC GATE TRANSMISSION SYSTEM ECO240-ECO360 INSTRUCTION MANUAL HYDRAULIC GATE TRANSMISSION SYSTEM ECO240-ECO360 IMPORTANT SAFETY INSTRUCTIONS WARNING! To reduce the risk of injury or death it is important to closely follow all of the following instructions.

More information

Installation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version

Installation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version Installation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version with operating bar with crank electrical version 1. Prerequisite for a correct installation of

More information

Electro-Pneumatic Bus Door Control Mechanism

Electro-Pneumatic Bus Door Control Mechanism Electro-Pneumatic Bus Door Control Mechanism Application and Feature 1. Pneumatic Door Mechanism actuates the open/close movements of bus door through two double acting cylinders and two linkages with

More information

APPLIED PNEUMATICS AND HYDRAULICS H TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS. This work covers part of outcome 2 of the standard Edexcel module.

APPLIED PNEUMATICS AND HYDRAULICS H TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS. This work covers part of outcome 2 of the standard Edexcel module. APPLIED PNEUMATICS AND HYDRAULICS H TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS This work covers part of outcome 2 of the standard Edexcel module. The material needed for outcome 2 is very extensive so

More information

Technical News Bulletin

Technical News Bulletin Technical News Bulletin January 2003 Two-way air operated Funnel Mechanism 200-2100 Up-Stroke Cushion Control Valve Top-mounted Check Valve Increased Stroke Rigid Cam Cam Roller Fixation Page 1/5 1. Description

More information

TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2

TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section

More information

Adjustments for the Active Pneumatic Vibration Isolation Table during Final Installation (File version 6)

Adjustments for the Active Pneumatic Vibration Isolation Table during Final Installation (File version 6) Adjustments for the Active Pneumatic Vibration Isolation Table during Final Installation (File version 6) Loosening the valves on the steel base plates of the valve assemblies during the installation procedure

More information

PART 2 FORKLIFT HYDRAULIC SYSTEM

PART 2 FORKLIFT HYDRAULIC SYSTEM PART 2 FORKLIFT HYDRAULIC SYSTEM Chapter 1 Description and Operation Component Locations & Circuit Layouts 1 Hydraulic Pump 11 Control Valve 14 Valve Section Oil Flows 15 Anti-Cavitation Valve 22 Velocity

More information

SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS

SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS README FIRST: Thank you for purchasing your MyDIYCNC Desktop CNC Machine Kit. We hope this versatile and innovative machine brings you many

More information

CAST IRON THE BASICS. Heatline - Cast Iron Radiators SMOOTH FLAT FILE TO REMOVE ANY SWARF. ONE TIME. ASSEMBLY. JOINTS SHOULD BE TIGHTENED.

CAST IRON THE BASICS. Heatline - Cast Iron Radiators SMOOTH FLAT FILE TO REMOVE ANY SWARF. ONE TIME. ASSEMBLY. JOINTS SHOULD BE TIGHTENED. CAST IRON THE BASICS 1. DO NOT LIFT ON YOUR OWN. 2. ONLY LIFT THE RADIATOR VERTICALLY. 3. DO NOT LIFT MORE THAN 8/10 SECTIONS AT ANY ONE TIME. 4. POSITION THE RADIATOR BEFORE FINAL ASSEMBLY. 5. THIS PRODUCT

More information

Lenntech. 1000 psi End port pressure vessels 2.5. User s Guide to: Phoenix Vessel Technology Limited. Model number: 1503

Lenntech. 1000 psi End port pressure vessels 2.5. User s Guide to: Phoenix Vessel Technology Limited. Model number: 1503 1 User s Guide to: Phoenix Vessel Technology Limited 1000 psi End port pressure vessels 2.5. Model number: 1503 Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Phoenix

More information

Operating Instructions Drill rig DRU160

Operating Instructions Drill rig DRU160 Operating Instructions Drill rig DRU160 Index 000 / 001 Original operating instructions 10988825 en / 20.10.2009 Congratulations! With a Hydrostress unit from TYROLIT you have chosen a tried and tested

More information

Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family

Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family Part of the Kiva Lighting Family Custom Lighting and Fans Since 1992 1312 12th St NW Albuquerque,

More information

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT

More information

Assembly Instructions Model 1544 Heart-Of-The-Kitchen Island

Assembly Instructions Model 1544 Heart-Of-The-Kitchen Island Assembly Instructions Model 1544 Heart-Of-The-Kitchen Island A. These units are Ready-to-Assemble. Catskill uses positive fastening methods such as wood screws and in some places hidden Bastion fasteners.

More information

Geometry and dimensional tolerances of engine bearings

Geometry and dimensional tolerances of engine bearings Geometry and dimensional tolerances of engine bearings Dr. Dmitri Kopeliovich (Research & Development Manager.) 1. Hydrodynamic lubrication Engine bearings operate mostly in the hydrodynamic regime of

More information

TRANS-05, Torque Tube Removal, Rebuilding, and Installation

TRANS-05, Torque Tube Removal, Rebuilding, and Installation TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket

More information

KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER

KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING

More information

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 www.airliftperformance.com MN-514 (06409) NPR 4762 Please read these instructions completely before proceeding with installation

More information

INSTALLATION INSTRUCTIONS FOR MODEL 1560 AND 1570 ELECTRIC TRIM CONTROL FOR USE WITH CORBIN 955 AND YALE 626F HEAVY DUTY TRIM

INSTALLATION INSTRUCTIONS FOR MODEL 1560 AND 1570 ELECTRIC TRIM CONTROL FOR USE WITH CORBIN 955 AND YALE 626F HEAVY DUTY TRIM II E1500-8 INSTALLATION INSTRUCTIONS FOR MODEL 1560 AND 1570 ELECTRIC TRIM CONTROL FOR USE WITH CORBIN 955 AND YALE 626F HEAVY DUTY TRIM FUNCTION DESCRIPTION 1560 FAIL SAFE LEVER IS LOCKED WHEN POWER IS

More information

SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3

SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PART #50190 SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER

More information

M A N U A L 13-10-05

M A N U A L 13-10-05 Documentation The following information sheets illustrate the description below: 12-WW01-4G-E Sectional view of the lance with main dimensions 12-W101-6G-E Sectional view of the head of the lance with

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than

More information

Pneumatic actuators The Original! Technics of the top class.

Pneumatic actuators The Original! Technics of the top class. Automatic valves Actuators Accessories Pneumatic actuators The Original! Technics of the top class. Leaflet no. S1-01e-13 Table of contents Advantages and your benefits...page 3 Figure: actuator...page

More information

MONDOATHENS BASKETBALL SET (Reference PK110)

MONDOATHENS BASKETBALL SET (Reference PK110) MONDOATHENS BASKETBALL SET (Reference PK110) DESCRIPTION The MONDOATHENS backstop unit is mainly designed for multi-sports pavilions and installations where the highest-level basketball competitions are

More information

The JIG is UP Or A couple hours up front pays in the long run.

The JIG is UP Or A couple hours up front pays in the long run. Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided

More information

SUSPENSION DIAGNOSIS

SUSPENSION DIAGNOSIS SECTION 2A SUSPENSION DIAGNOSIS TABLE OF CONTENTS Diagnosis... 2A-2 General Diagnosis... 2A-2 Hub and Bearing... 2A-7 2A-2 SUSPENSION DIAGNOSIS DIAGNOSIS GENERAL DIAGNOSIS Problems in the steering, the

More information

SICONT Limit Switches Type 3SE3 upto 500 VAC, 600 VDC, 10A

SICONT Limit Switches Type 3SE3 upto 500 VAC, 600 VDC, 10A s SICONT Limit Switches Type 3SE3 upto 500 VAC, 600 VDC, 10A Introduction The technical and descriptive information on the function, construction and selection of the new types of 3SE3 limit switches is

More information

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997 Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47

More information

Profile rail guides LLR

Profile rail guides LLR Profile rail guides LLR Content The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17) 17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure

More information

TN2000 Series Pneumatic Piston Actuators for DN125 to DN300 SPIRA-TROL Series Control Valves

TN2000 Series Pneumatic Piston Actuators for DN125 to DN300 SPIRA-TROL Series Control Valves Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism

More information

INSTRUCTION. Industrial Sewing Machines. No. 010012. First published : June 1997 Second edition : March 2001

INSTRUCTION. Industrial Sewing Machines. No. 010012. First published : June 1997 Second edition : March 2001 INSTRUCTION Industrial Sewing Machines First published : June 1997 Second edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's DLR Series. Read and study this instruction

More information

MP8000 Series Pneumatic Valve Actuators

MP8000 Series Pneumatic Valve Actuators 14-1161- 9, Rev. A Technical Bulletin MP8000 Issue Date March 2016 MP8000 Series Pneumatic Valve Actuators Pre-Assembly Details Page 3 MP8000 Actuator Components 3 Tools Required to Assemble an MP8000

More information

http://localhost/vida/jsp/information/xml/xmldocprintpreview.jsp

http://localhost/vida/jsp/information/xml/xmldocprintpreview.jsp Page 1 of 7 60: Wheel alignment V70 XC (01-) / XC70 (-07), 2001, B5244T3, AW50/51 AWD, L.H.D, YV1SZ58D811036138, 036138 5/4/2014 PRINT 60: Wheel alignment Wheel alignment, checking / adjusting Note! For

More information

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW Vinyl Windows and Doors Manufactured by Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW Lea las instrucciones en español en el reverso.

More information

These Installation Instructions are valid for antennas in the following version:

These Installation Instructions are valid for antennas in the following version: Installation Instructions 4 ft CompactLine Antennas (with E-Mount 250 km/h) SB, SBX NMT 560-05(e) These Installation Instructions are valid for antennas in the following version: Reflector Ø 1.2 m (4 ft)

More information

Lathe Milling Attachment

Lathe Milling Attachment Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,

More information

Lunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide

Lunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your

More information

DiscPlus DX195 and DX225 Air Disc Brakes

DiscPlus DX195 and DX225 Air Disc Brakes Revised 11-04 Technical Bulletin Revised 1 Technical 11-04 Bulletin DiscPlus DX195 and DX225 Air Disc Brakes Inspection, Installation and Diagnostics Air Disc Brake Inspection Intervals and Procedures

More information

Jet Propulsion System

Jet Propulsion System This repair manual is valid for the following jet pump variants: 0333_ 0 V3 007 3. 033_ 0 V 007 3. 0380_ 3 V 007 3. 0335_ 3 V 007 3. 033_ 66 V 008. 0338_ 66 V 008. Table of Contents Before you begin working

More information

DeZURIK 3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT

DeZURIK 3-20 BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT 3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT Instruction D10386 August 2013 Instructions These instructions provide installation, operation and maintenance information for BAW Butterfly Valves.

More information

HYDRAULIC LIFT TABLE CART 2200-LB.

HYDRAULIC LIFT TABLE CART 2200-LB. HYDRAULIC LIFT TABLE CART 2200-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other

More information

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate

More information

Technical Information

Technical Information Technical Information This section of the catalogue provides technical information that will help specify, install and maintain Surelock McGill devices and components. The topics are listed below: Blast

More information

Power Window/Power Lock Installation. To begin with you will need all the parts listed below:

Power Window/Power Lock Installation. To begin with you will need all the parts listed below: Power Window/Power Lock Installation To begin with you will need all the parts listed below: From Donor Fiero: Fiero power window regulators Power window motors (Generic GM type part) -motors are riveted

More information

IRS AUTOMATISMOS Y SISTEMAS. Avinguda Generalitat, 107 entresuelo 2 Tel: 977 444 059 Fax: 977 441 633 43500 TORTOSA www.irs-as.com info@irs-as.

IRS AUTOMATISMOS Y SISTEMAS. Avinguda Generalitat, 107 entresuelo 2 Tel: 977 444 059 Fax: 977 441 633 43500 TORTOSA www.irs-as.com info@irs-as. Avinguda Generalitat, 107 entresuelo 2 Tel: 977 444 059 Fax: 977 441 633 43500 TORTOSA www.irs-as.com info@irs-as.com INDEX 1.- HISTORY...3 2.- ADVANTAGES AND OPTIONS OF PRODUCT BCR-X520...4 3.- ESPECIFICATIONS

More information

M-06-09 REV. B APRIL 2008 OPERATION MANUAL GPT-25, GPT-3, GPT-4 & GPT-5

M-06-09 REV. B APRIL 2008 OPERATION MANUAL GPT-25, GPT-3, GPT-4 & GPT-5 M-06-09 REV. B APRIL 2008 OPERATION MANUAL GPT-25, GPT-3, GPT-4 & GPT-5 MAXON Lift Corp. 2008 TABLE OF CONTENTS WARNINGS... 4 LIFTGATE TERMINOLOGY... 5 RECOMMENDED DAILY OPERATION CHECKS... 6 DECALS...

More information

STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES

STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES GATE VALVE O.S. & Y 1.0 Periodic Inspections 1.1 The valve stem packing should be inspected at least monthly. If the stem packing shows signs of leakage, simply tighten the adjusting nuts to compress the

More information

Direct Operated Regulator for 6.0 MPa (Relieving Type) How to Order. Body size 30 40

Direct Operated Regulator for 6.0 MPa (Relieving Type) How to Order. Body size 30 40 Direct Operated Regulator for (Relieving Type) Series Service life: 0 million cycles Using NSF-H-certified grease on the guide ring (sliding) part. Improved durability under a high environment with a polyurethane

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure

More information

Webinar Series. Committee. Disc Brake Wheels Off Inspection and Reline. Presents

Webinar Series. Committee. Disc Brake Wheels Off Inspection and Reline. Presents 1 APTA Bus Webinar Technical Series Maintenance Committee Webinar Series Presents Disc Brake Wheels Off Inspection and Reline January 21, 2015 2 Introduction Welcome to today s webinar in which we will

More information

System 8. ü www.nassmagnet.com ( +49 511 6746-0. System 8

System 8. ü www.nassmagnet.com ( +49 511 6746-0. System 8 System 8 ü www.nassmagnet.com ( +9 11 7-0 System 8 The name System 8 stands for a modular system of solenoid coils, armature systems, solenoid operators and solenoid valves. The diameter of the armatures

More information

Service Manual Rol-Lift

Service Manual Rol-Lift R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing

More information

HYDRAULIC TABLE CART 500-LB.

HYDRAULIC TABLE CART 500-LB. HYDRAULIC TABLE CART 500-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic

More information

TECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work

TECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work Revised 02-00 TECHNICAL BULLETIN Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves This technical bulletin covers both cab and chassis leveling valves manufactured by Meritor WABCO. While the

More information

MGB Chrome Bumper Conversion

MGB Chrome Bumper Conversion MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different

More information

SureSite Magnetic Liquid Level Indicator

SureSite Magnetic Liquid Level Indicator SureSite Magnetic Liquid Level Indicator Instruction Bulletin No. 177664-1 (Rev. E) Section 1: Weldments Thank you for purchasing the GEMS SureSite Magnetic Level Indicator. Please read this document prior

More information

I BEAM TRACK INSTALLATION

I BEAM TRACK INSTALLATION PDQ 0/700 FESTOON SYSTEM INSTALLATION AND MAINTENANCE INSTRUCTIONS INTRODUCTION The PDQ Festoon System was designed to run on one of three sizes of I-beams: S x., S8 x 8. and S x.. System trolleys must

More information

Fish Grader User Manual

Fish Grader User Manual Fish Grader User Manual 1400 Fish Grader Contents Basic Parts... 2 Set up... 3 Control board needs to be setup... 3 Adjustable legs... 3 Adjustable Inlet cute... 3 Motor... 3 Control-board... 4 Remote

More information

Rear Impact Guard TEST METHOD 223. Standards and Regulations Division. Issued: December 2003

Rear Impact Guard TEST METHOD 223. Standards and Regulations Division. Issued: December 2003 Transport Canada Safety and Security Road Safety Transports Canada Sécurité et sûreté Sécurité routière Standards and Regulations Division TEST METHOD 223 Rear Impact Guard Issued: December 2003 Standards

More information

VAD Variable Area Desuperheaters

VAD Variable Area Desuperheaters Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

SERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair

SERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair SERVICE MANUAL US Corpus 3G Seat system for electric wheelchair How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Version 4, 2014-07 Item No.: 205260-US-0

More information

Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19

Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19 Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR

More information

Section 5: Machine Overview

Section 5: Machine Overview Section 5: Machine Overview Machine Floor Plan Machine Specifications Sequence of Operation Theory of Operation Sensor Location Floor Plan 2007 Douglas Machine Inc. 5.1 Machine Floor Plan Figure 5.1: Machine

More information

Things you need to assemble the tube actuator. Left to right. are small piece of masking tape, super glue,pen knife and small

Things you need to assemble the tube actuator. Left to right. are small piece of masking tape, super glue,pen knife and small Things you need to assemble the tube actuator. Left to right are small piece of masking tape, super glue,pen knife and small crosspoint screwdriver. You will also need a few drops of light oil. Begin by

More information

SCION tc 2005-2008 COIL OVER SUSPENSION Preparation

SCION tc 2005-2008 COIL OVER SUSPENSION Preparation SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description

More information

Fluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS

Fluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS Fluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS up to size 381; to PN 0.5; to T = 80 C 1. Description 1.1. General FSA fluid level gauges, FSK fluid level sensors and TS temperature

More information

Cylinder head, removing and replacing

Cylinder head, removing and replacing 15-1 Cylinder head, removing and replacing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail

More information

Oregon Fuel Injection

Oregon Fuel Injection Corporate Office: P.O. Box 21121, VE Pump Removal and Installation Cummins Lock Timed Applications Removal Clean the exterior of the injection pump and mounting surfaces. 1. Disconnect the fuel return

More information

Step by step guide to installing your own Ku Band satellite dish

Step by step guide to installing your own Ku Band satellite dish Step by step guide to installing your own Ku Band satellite dish If you don't feel comfortable installing your own system, your local TV Aerial or Handyman can easily follow these helpful guidelines for

More information

AXLE SHAFTS - FRONT. 1993 Toyota Celica DESCRIPTION REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION. 1993 DRIVE AXLES Toyota FWD Axle Shafts

AXLE SHAFTS - FRONT. 1993 Toyota Celica DESCRIPTION REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION. 1993 DRIVE AXLES Toyota FWD Axle Shafts AXLE SHAFTS - FRONT 1993 Toyota Celica 1993 DRIVE AXLES Toyota FWD Axle Shafts Toyota; Celica DESCRIPTION Axle shafts transfer power from transaxle to driving wheels. All axle shafts consist of a shaft

More information

PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS

PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS SYSTEM COMPONENTS PREASSEMBLED ELEMENTS FOR FIFTING AND SLIDING DOORS s r ood gn i d i l s dna gn i t f i f r o f s t neme l e de l bme s s ae r P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS These

More information

POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS

POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing

More information

13. REAR WHEEL/BRAKE/SUSPENSION

13. REAR WHEEL/BRAKE/SUSPENSION 13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...

More information

Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995)

Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995) Convertible Top Hydraulic Cylinder Removal Manual for W124 E-Class Convertibles 1993-1995 Models 300CE (1993) and E320 (1994-1995) Written by Samit Ghosh with picture material from vexed of benzworld.org

More information

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008) Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the

More information

Maxi-Stamper. 200 to 1,000 Tons STAMPING OUT DOWNTIME

Maxi-Stamper. 200 to 1,000 Tons STAMPING OUT DOWNTIME TM Maxi-Stamper 200 to 1,000 Tons STAMPING OUT DOWNTIME Standard Features Steel Fabricated Construction Drive Capacity Rated 1/2 Above Bottom of Stroke Self-Diagnostic Solid State Controller Moveable Operator

More information

INSTRUCTIONS: LocknCharge Laptop Carts

INSTRUCTIONS: LocknCharge Laptop Carts INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes

More information