Barak & Caldera Network Setup
|
|
- Gloria McCoy
- 8 years ago
- Views:
Transcription
1 Barak & Caldera Network Setup Application Note Rev. A February 2008 Prepared by the Application Department A Matan Digital Printers Ltd. Page 1 of 17
2 Safety Procedures Before reading this Application Note, please refer to the section on Safety Procedures in the Barak User's Manual. About this Application Note The document gives instructions on how to configure the Barak and Caldera network settings. Barak and Caldera Network Setup Hardware Connections Barak PC Settings Each of the Barak and the Caldera PCs has two network cards installed. In addition, two network cables are supplied by Matan. One cable connects the Barak PC to the Controller or to the Backlit Cameras (if installed). The other cable connects the Barak PC to the Caldera PC. Barak PC Network Cards Settings 1. In the Barak PC, click START, SETTINGS, and then NETWORK CONNECTIONS A Matan Digital Printers Ltd. Page 2 of 17
3 2. Double-click the CONTROLLER CARD and click PROPERTIES. 3. Select the "Internet Protocol (TCP/IP)" from the list and click PROPERTIES A Matan Digital Printers Ltd. Page 3 of 17
4 4. Enter the following IP address and click O.K. Network Card I (Connected to the Controller) IP Address (static): Subnet Mask: A Matan Digital Printers Ltd. Page 4 of 17
5 5. Click OK and close the PROPERTIES dialog box. 6. Repeat steps 2 5 for the CALDERA NETWORK CARD, with the following IP address. Network Card II (Connected to the Caldera PC) IP Address (static): Subnet Mask: A Matan Digital Printers Ltd. Page 5 of 17
6 Creating a Sharing Folder The input folder is a shared folder on the Barak's PC, where all the RIPped files will be saved 1. On the C: drive, create a new folder named INPUT. 2. Right-click the folder and select SHARING AND SECURITY. 3. From the SHARING tab, choose the SHARE THIS FOLDER option A Matan Digital Printers Ltd. Page 6 of 17
7 4. Click the ALLOW NETWORK USERS TO CHANGE MY FILES option. 5. Click OK A Matan Digital Printers Ltd. Page 7 of 17
8 Caldera PC Settings Caldera PC Network Cards Settings 1. On the Caldera PC, click START and select SYSTEM SETTINGS. 2. Click the NETWORK SETTINGS icon A Matan Digital Printers Ltd. Page 8 of 17
9 3. Click ADMINISTRATOR MODE. 4. When prompted, enter the password (caldera). The system detects two network cards eth0 (which should be connected to the Barak printer) and eth1 (which should be connected to the file server). 5. Double-click eth0 to open it and choose the MANUAL option. 6. Enter the following IP address. Network Card eth0 (Connected to the Barak PC) IP Address (static): Netmask: A Matan Digital Printers Ltd. Page 9 of 17
10 IP Address: 7. Click OK. 8. Double-click eth1 to open it and choose the AUTOMATIC option or enter a static IP address provided by your site network manager. Network Card II (Connected to the Site Ethernet) DHCP or Static IP from site network manager 9. Click OK. 10. Open the ROUTES tab and make sure that the DEFAULT GATEWAY IP ADDRESS field is clear. 11. Click APPLY A Matan Digital Printers Ltd. Page 10 of 17
11 Mounting the Input Folder from the Caldera PC So that you can see the Barak Input Shared folder from the Caldera PC, you need to mount it. 1. Make sure that the Barak PC is turned ON and then restart the Caldera PC. 2. On Caldera's main screen, click Smb4K. 3. To search for connected computers, click SCAN NETWORK. If the PC cannot be found, open the SEARCH DIALOG tab and enter the static IP address of the Barak PC. 4. In the left section of the Smb4K screen, double-click the Barak PC icon and then the Input folder A Matan Digital Printers Ltd. Page 11 of 17
12 5. A hard-disk icon appears in the right section of the Smb4K screen. The folder is now mounted. 6. To mount the file server, repeat steps 3 5, but in step 4, remember to click the icon for the relevant PC. 7. Select the icons for the mounted folders and from the BOOKMARKS menu, select ADD BOOKMARK. Configuring the Input Folder as the Default Folder for RIPped Files 1. From the SETTINGS tab on Caldera's main screen, click SERVERADMIN A Matan Digital Printers Ltd. Page 12 of 17
13 The SERVERS ADMINISTRATION window appears. 2. From the SERVERS ADMINISTRATION window, choose the BarakHS Printer and click CONFIGURE. 3. Open the FILES tab and click the ROOT's field browse button. The FILE SELECTION window appears A Matan Digital Printers Ltd. Page 13 of 17
14 4. In the File Selection window, click the Go to Parent Directory until you arrive at the "/" directory. 5. Double-click MNT/. 6. Double-click BARAK-XXXX. 7. Double-click INPUT. 8. Click OPEN A Matan Digital Printers Ltd. Page 14 of 17
15 The path to the input folder now appears in the ROOT field of the BASE DIRECTORY. 9. Click PROCEED A Matan Digital Printers Ltd. Page 15 of 17
16 10. When prompted, enter the Password (Caldera) and click OK. 11. In the SERVERS ADMINISTRATION window, click QUIT. 12. Restart the Caldera application A Matan Digital Printers Ltd. Page 16 of 17
17 Document History Rev ECO # Written by Date Approved by A F. Taylor Technical Writer F. Taylor Date Remarks Cataloging Reference to Safety Head Office Matan Digital Printers Ltd., 14 Amal Street, Park Afek, Rosh Ha'ayin 48092, Israel. Tel: (+972) Fax: (972) support@matanprinters.com U.S. Office Matan USA Inc., 90, Earhart Drive, Suite 4, Williamsville NY Tel: (+1) Fax: (1) for customer support: support@matanprinters.com Europe Office Matan EU, C/ Rosalia de Castro, 21, 08025, Barcelona, Spain. Tel: (+34) Fax: (+34) for customer support: support.eu@matanprinters.com A Matan Digital Printers Ltd. Page 17 of 17
Replacing PCBs PCI P/N 88800124 BCC P/N 88800137 Back Plane P/N 88800160 DC-to-DC P/N 77700236
Replacing PCBs PCI P/N 88800124 BCC P/N 88800137 Back Plane P/N 88800160 DC-to-DC P/N 77700236 Technical Note 10100144 Rev. A 10100144 - A Matan Digital Printers Ltd. Page 1 of 11 Safety Procedures Before
More informationDP-313 Wireless Print Server
DP-313 Wireless Print Server Quick Installation Guide TCP/IP Printing (LPR for Windows 95/98/Me/2000) Rev. 03 (August, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may
More information1. Hardware Installation
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
More informationUsing a simple crossover RJ45 cable, you can directly connect your Dexter to any computer.
Dexter is a network device using the Ethernet protocol to connect and communicate with other devices on the network: Computers, routers, DHCP servers. Thus you have to setup your Dexter and your network
More informationLPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide. Rev. 03 (November, 2001)
LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide Rev. 03 (November, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may be reproduced in any form or by any
More informationInstalling the Microsoft Network Driver Interface
Installing the Microsoft Network Driver Interface Overview This guide explains how to install the PictureTel Live200 Microsoft Network Driver Interface (NDIS) software you have downloaded from PictureTel's
More informationSATO Network Interface Card Configuration Instructions
SATO Network Interface Card Configuration Instructions Table of Contents 1. Reset of wired/wireless interface card... 3 2. Installing the All-In-One Utility (recommended)... 4 3. Configuring wired/wireless
More informationLPT1 Printer Connector. External Power Supply Connector Power Indicator
AXIS 1650 Set-up Instructions Page 3 Unpack box Verify that you have all the items listed below: LPT1 Printer Connector Network Indicator Ethernet Connector External Power Supply Connector Power Indicator
More informationConfiguring the WT-4 for ftp (Ad-hoc Mode)
En Configuring the WT-4 for ftp (Ad-hoc Mode) Windows XP Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 ftp server
More informationSetting Up Your FTP Server
Requirements:! A computer dedicated to FTP server only! Linksys router! TCP/IP internet connection Steps: Getting Started Configure Static IP on the FTP Server Computer: Setting Up Your FTP Server 1. This
More informationRecommended Network Setup
Recommended Network Setup Greater Giving Event Software uses Windows File Sharing to allow multiple computers to connect to the same database within your network. This document uses Windows XP as the default
More informationChapter7 Setting the Receiving PC for Direct Upload. Setting the Receiving PC for Direct Upload... 148 For Windows... 148 For Macintosh...
Chapter7 Setting the Receiving PC for Direct Upload Setting the Receiving PC for Direct Upload... 148 For Windows... 148 For Macintosh... 153 Setting the Receiving PC for Direct Upload This section explains
More informationStep-by-Step Setup Guide Wireless File Transmitter FTP Mode
EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Infrastructure Setup Windows XP 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without permission is prohibited.
More informationPre-lab and In-class Laboratory Exercise 10 (L10)
ECE/CS 4984: Wireless Networks and Mobile Systems Pre-lab and In-class Laboratory Exercise 10 (L10) Part I Objectives and Lab Materials Objective The objectives of this lab are to: Familiarize students
More informationUSER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
More informationPrint Audit 6 - SQL Server 2005 Express Edition
Print Audit 6 - SQL Server 2005 Express Edition Summary This is a step-by-step guide to install SQL Server 2005 Express Edition to use as a database for Print Audit 6. Pre-Requisites There are a few pre-requisites
More informationCMP-102U. Quick Installation Guide
CMP-102U Quick Installation Guide V1.0 http://www.cnet.com.tw 1 CMP-102U Supports One High-speed USB2.0 Port MFP Server Supports 10/100Mbps Fast Ethernet Network Quick Installation Guide 1 Package Contents:
More informationDeploying Windows Streaming Media Servers NLB Cluster and metasan
Deploying Windows Streaming Media Servers NLB Cluster and metasan Introduction...................................................... 2 Objectives.......................................................
More informationStep-by-Step Setup Guide Wireless File Transmitter FTP Mode
EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Ad Hoc Setup Windows XP 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without permission is prohibited. 1
More information4-441-095-12 (1) Network Camera
4-441-095-12 (1) Network Camera SNC easy IP setup Guide Software Version 1.0 Before operating the unit, please read this manual thoroughly and retain it for future reference. 2012 Sony Corporation Table
More information1. Installing The Monitoring Software
SD7000 Digital Microphone Monitor Software manual Table of Contents 1. Installing The Monitor Software 1.1 Setting Up Receivers For Monitoring 1.2 Running The Application 1.3 Shutdown 2. The Detail Monitoring
More informationUsing TViX Network. NFS mode : You must install the TViX NetShare utility in to your PC, but you can play the TP or DVD jukebox without stutter.
Using TViX Network There are two network mode. One is SAMBA mode another is NFS mode. SAMBA mode : You can play the file via network without special program, but the speed is lower than NFS mode. ( Currently,
More informationSTATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM Verizon High Speed Internet for Business Verizon High Speed Internet for Business SETTING UP YOUR NEW STATIC IP CONNECTION AND IP ADDRESS(ES) This
More informationEthernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2
Ethernet Interface Manual Thermal / Label Printer Rev. 1.01 Metapace T-1 Metapace T-2 Metapace L-1 Metapace L-2 Table of contents 1. Interface setting Guiding...3 2. Manual Information...4 3. Interface
More informationInterfacing Basler GigE Cameras With Cognex VisionPro 7.2
www.baslerweb.com Interfacing Basler GigE Cameras With Cognex VisionPro 7.2 This Application Note explains how to interface a Basler camera with GigE interface with the Cognex VisionPro 7.2 software package
More informationOmni 56K USB Lite Quick Start Guide
Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack
More informationDiscovery Tool for COMbricks Quick Start Guide
Discovery Tool for COMbricks Introduction The Discovery Tool for COMbricks makes it easy to: Find all available Head Stations in your entire network (also other IP ranges!) Identify the correct COMbricks
More informationQuick Installation Guide Network Management Card
Rev.1.1 www.cyberpowersystems.com Quick Installation Guide Network Management Card Intelligent Network Management Card allows UPS to be managed, monitored, and configured via SNMP Card Configuration Tool
More informationLPR for Windows 95 TCP/IP Printing User s Guide
LPR for Windows 95 TCP/IP Printing User s Guide First Edition Printed in Taiwan, R.O.C. RECYCLABLE Copyright Statement Trademarks Limited Warranty Copyright 1997 D-Link Corporation No part of this publication
More informationClock Link Installation Guide. Detailed brief on installing Clock Link
Clock Link Installation Guide Detailed brief on installing Clock Link 1 Table of Contents 1. Overview... 3 2. Configuring the Time Clock... 3 Instructions:... 3 2.1 IP Address Setup... 3 2.2 Subnet Mask
More information1 PC to WX64 direction connection with crossover cable or hub/switch
1 PC to WX64 direction connection with crossover cable or hub/switch If a network is not available, or if it is desired to keep the WX64 and PC(s) completely separated from other computers, a simple network
More informationChapter 2 Preparing Your Network
Chapter 2 Preparing Your Network This document describes how to prepare your network to connect to the Internet through a router and how to verify the readiness of your broadband Internet service from
More informationAppendix B Lab Setup Guide
JWCL031_appB_467-475.indd Page 467 5/12/08 11:02:46 PM user-s158 Appendix B Lab Setup Guide The Windows Server 2008 Applications Infrastructure Configuration title of the Microsoft Official Academic Course
More informationDialing Into Dartmouth With Windows 95/98
Dialing Into Dartmouth With Windows 95/98 Who needs this document? Any member of the Dartmouth community who wants to gain access to Dartmouth s network resources, such as electronic mail and the Internet,
More informationUBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY)
UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY) Hardware Installation 1. Initial placement for programming and configuration purposes should be performed in an indoor environment.
More informationGuide to Setting up Internet Connection Sharing for Windows
Guide to Setting up Internet Connection Sharing for Windows Document Date: December 20, 2005 Document Version: Version: 1.0 Disclaimer: Please note that this document is provided on an as is where is basis
More informationTRENDnet. <a href="mailto:webmaster@ trendnet.com"> www.trendnet.com. Quick Installation Guide. Product Warranty Registration
Quick Installation Guide Product Warranty Registration website at http://www.trendnet.com www.trendnet.com Please take a moment to register your product online.
More informationEDGE FX Network configuration
Page 1 of 16 TITLE: Category: EDGE FX Network configuration GERBER EDGE Document Number: 4280 Supplied by: Gerber Service Last Modified: April 14, 2011 Summary: In order to connect an EDGE FX to your PC
More informationConfigure SPLM 2012 on Windows 7 Laptop
Configure SPLM 2012 on Windows 7 Laptop 7/12/2012 SmartPlant License Manager (SPLM) requires a static IP Address on the license machine. To fulfill this requirement on laptops a virtual network adapter
More information64-Bit Compatibility with Micromeritics Applications
Tech Tip 7 64-Bit Compatibility with Micromeritics Applications Micromeritics products are designed to operate in most Microsoft Windows environments. However, more current versions of Microsoft Windows,
More informationIntraVUE Plug Scanner/Recorder Installation and Start-Up
IntraVUE Plug Scanner/Recorder Installation and Start-Up The IntraVUE Plug is a complete IntraVUE Hardware/Software solution that can plug directly into any network to continually scan and record details
More informationPreparing the Windows version of the software for use
Preparing the Windows version of the software for use System requirements Component Processor RAM Hard disk Drives Interfaces/network TCP/IP internet protocol Screen Installing the Conference Manager software
More informationHow To Install And Configure Windows Server 2003 On A Student Computer
Course: WIN310 Student Lab Setup Guide Microsoft Windows Server 2003 Network Infrastructure (70-291) ISBN: 0-470-06887-6 STUDENT COMPUTER SETUP Hardware Requirements All hardware must be on the Microsoft
More information10.3.1.8 Lab - Configure a Windows 7 Firewall
5.0 10.3.1.8 Lab - Configure a Windows 7 Firewall Print and complete this lab. In this lab, you will explore the Windows 7 Firewall and configure some advanced settings. Recommended Equipment Step 1 Two
More informationChanging Your Cameleon Server IP
1.1 Overview Technical Note Cameleon requires that you have a static IP address defined for the server PC the Cameleon server application runs on. Even if the server PC has a static IP address, you may
More informationNetLINE Wireless Broadband Gateway
NetLINE Setup Guide Farallon s NetLINE connects to your cable/dsl modem, allowing computers on your local wired and wireless networks to share a single broadband connection to the Internet. This Setup
More informationD-Link DAP-1360 Repeater Mode Configuration
D-Link DAP-1360 Repeater Mode Configuration Outline 1. Package Contents 2. System Requirements 3. Hardware Overview Connections LED s WPS LED/Button 4. Default Settings 5. Configuring your LAN Adapter
More informationConfiguring the WT-4 for ftp (Infrastructure Mode)
Introduction En Configuring the WT-4 for ftp (Infrastructure Mode) This document provides basic instructions on configuring the WT-4 wireless transmitter and a ftp server for transmission over an infrastructure
More informationAcqKnowledge 3.7.3 or better for Windows OS (version compatibility varies each release)
APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 209: AcqKnowledge for Windows: Upgrade for 1+MP150s and
More informationLAN TCP/IP and DHCP Setup
CHAPTER 2 LAN TCP/IP and DHCP Setup 2.1 Introduction In this chapter, we will explain in more detail the LAN TCP/IP and DHCP Setup. 2.2 LAN IP Network Configuration In the Vigor 2900 router, there are
More informationTB168 (Rev4) - Networking Linux Based Controls
TB168 (Rev4) - Networking Linux Based Controls Creating a Network If not already connected, create the network using cables, switches, routers, etc. To successful connect a DHCP network you will require
More informationApple Mac. AT&T DSL Internet Service Implementation Planner Apple Mac PC Configuration Guide Version 1.2 Page 1
Apple Mac Page 1 Apple Mac Setup Welcome to AT&T DSL Internet Service! This guide is designed to help you configure your Mac to access the Internet quickly and easily using AT&T DSL. Before You Begin First,
More informationOperating Instructions
Operating Instructions (For Setting up the Printer Driver and the Panasonic Document Management System) Digital Imaging Systems Model No. DP-800P / 800E / 806P Installation Table of Contents Installation
More informationNetwork Scanner Tool R3.1. User s Guide Version 3.0.04
Network Scanner Tool R3.1 User s Guide Version 3.0.04 Copyright 2000-2004 by Sharp Corporation. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited,
More informationApplication Note Configuring the UGate 3000 for use with ClipMail Pro and ClipExpress
Application Note Configuring the UGate 3000 for use with Introduction This Application Note guides the ClipMail user through the UGate gateway configuration process by using a simple dial up connection
More informationConnecting the DG-102S VoIP Gateway to your network
Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information
More informationLee County School Configuring Spec Ed Laptop Computers for Dialup, DSL/Cable Modem, and Wireless Access To the Internet
Lee County School Configuring Spec Ed Laptop Computers for Dialup, DSL/Cable Modem, and Wireless Access To the Internet Prepared by: Rich Morgan Technology Director Configuring your Spec Ed laptop for
More informationClassroom Management network FAQ and troubleshooting
Classroom Management network FAQ and troubleshooting Author: Grant Kelly The concepts in this document are intended to be a guide to aid in the resolution of certain issues that occur with using the Classroom
More informationWireless G Broadband quick install
Wireless G Broadband Router quick install guide Model 503693 INT-503693-QIG-0608-02 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless G Broadband Router, Model 503693. This quick install
More informationTN-0043. Using FileZilla FTP Server with a DT80 Series Logger
Using FileZilla FTP Server with a DT80 Series Logger File Transfer Protocol (FTP) is used by the datataker DT80 range data loggers when pushing data to a file server. This server could be located remotely
More informationLOAD BALANCING 2X APPLICATIONSERVER XG SECURE CLIENT GATEWAYS THROUGH MICROSOFT NETWORK LOAD BALANCING
SECURE CLIENT GATEWAYS THROUGH MICROSOFT NETWORK LOAD BALANCING Contents Introduction... 3 Network Diagram... 3 Installing NLB... 3-4 Configuring NLB... 4-8 Configuring 2X Secure Client Gateway... 9 About
More informationHow to use edgebox as a PDC and to Share Files
edgebox V4.5 How to use edgebox as a PDC and to Share Files Rev - 1.1 1 Storage and Print - Windows Domain Storage & Print EdgeBOX may be configured to interact with other hosts as if it was a Windows
More informationCYAN SECURE WEB APPLIANCE. User interface manual
CYAN SECURE WEB APPLIANCE User interface manual Jun. 13, 2008 Applies to: CYAN Secure Web 1.4 and above Contents 1 Log in...3 2 Status...3 2.1 Status / System...3 2.2 Status / Network...4 Status / Network
More informationPrinter Sharing of the PT-9500pc in a Windows Environment
Printer Sharing of the PT-9500pc in a Windows Environment This procedure is for configuring the PT-9500pc as a shared printer in Microsoft Windows. For printer sharing to operate correctly, please be sure
More informationEasy Setup Guide for the Sony Network Camera
-878-191-11 (1) Easy Setup Guide for the Sony Network Camera For setup, a computer running the Microsoft Windows Operating System is required. For monitoring camera images, Microsoft Internet Explorer
More informationCanon WFT-E1 (A) Wireless File Transmitter. Network Support Guide
1 Canon WFT-E1 (A) Wireless File Transmitter Network Support Guide Windows XP - Infrastructure Wireless Mode Connection 2 Setting up the WFT-E1A on Windows XP Home or Professional Infrastructure Wireless
More informationPePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400
PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Outdoor Series: Surf AP 200/400-X, PolePoint 400-X, Surf 400-DX User Manual Document Rev. 1.2 July 07 COPYRIGHT & TRADEMARKS
More informationEnabling Internet Connection Sharing on Windows 2000 15. Enabling ICS On Windows XP As The Host 4 Enabling ICS On Windows XP As The Client 11
Sharing an Internet Connection with SatDirect Plus Table of Contents Contents Section 1: Section 2: Section 3: Introduction... 1 Physical Setup......2 Enabling Internet Connection Sharing on Windows XP
More informationInternet Guide. Prepared for 55 John Street
Internet Guide Prepared for 55 John Street I. Internet Service How do I connect to the Internet? WiFi (Wireless Connectivity) is available throughout the building. In order to connect, you will need a
More informationMoxa Device Manager 2.3 User s Manual
User s Manual Third Edition, March 2011 www.moxa.com/product 2011 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used
More informationNETWORK SETUP INSTRUCTIONS
NETWORK SETUP INSTRUCTIONS How to Connect AVTECH Product to Internet To connect AVTECH DVR or network camera to Internet, you need to: 1). Figure out your network environment, and have related IP information
More informationCourse: WIN310. Student Lab Setup Guide. Summer 2010. Microsoft Windows Server 2003 Network Infrastructure (70-291)
Course: WIN310 Student Lab Setup Guide Summer 2010 Microsoft Windows Server 2003 Network Infrastructure (70-291) ISBN: 0-470-06887-6 Published by Wiley & Sons 1 STUDENT COMPUTER SETUP Hardware Requirements
More informationFLX VoIP Registering with Avaya IP Office 500
FLX VoIP Registering with Avaya IP Office 500 Date: April 5 th, 2012 This technical note gives a detailed description on how to register a Revolabs FLX conference phone with Avaya IP Office 500 PBX. On
More informationWindows 98 and Windows Me
Windows 98 and Windows Me This topic includes: "Preliminary Steps" on page 3-25 "Quick CD-ROM Install Steps" on page 3-26 "Other Methods of Installation" on page 3-26 "Windows 98 and Windows Me Troubleshooting"
More informationBASLER ACE QUICK INSTALLATION GUIDE
BASLER ACE QUICK INSTALLATION GUIDE Rev. 01 Quick installation Guide V1 1 Introduction The installation procedures in this guide assume that you want to get your camera operational and begin capturing
More informationIntroduction. Before you begin. Installing efax from our CD-ROM. Installing efax after downloading from the internet
Introduction Before you begin Before you begin installing efax, please check the following: You have received confirmation that your application for the efax service has been processed. The confirmation
More informationNXT Controller Manual IP Assignment in WAN Environments Application Note
It is difficult to perform NXT controller IP address assignment and auto-configuration when controllers are on different subnets from the local PC (the PC from which the Doors.NET client is run). This
More informationBioWin Network Installation
BioWin Network Installation Introduction This document outlines the procedures for installing the network version of BioWin. There are three parts to the network version installation: 1. The installation
More informationIf you never used nor intend to use the wired-connection, then please disregard the following info.
Version date: 21/04/2015 Dear library users, In the library you can connect to the internet in two ways, using wireless or a wired-connection. The wired-connection is faster, allows you to connect to the
More informationConfiguring the CyberData VoIP 4-Port Zone Controller with Audio Out
NetVanta Unified Communications Technical Note Configuring the CyberData VoIP 4-Port Zone Controller with Audio Out Introduction The CyberData Voice over Internet Protocol (VoIP) zone controller enables
More informationNetwork Printing In Windows 95/98/ME
Network Printing In Windows 95/98/ME If you are using Windows 2000/ XP: To install a printer on your network using D-Link Print Server or DI-series router with built-in print server you do not need to
More informationDeployment Guide: Transparent Mode
Deployment Guide: Transparent Mode March 15, 2007 Deployment and Task Overview Description Follow the tasks in this guide to deploy the appliance as a transparent-firewall device on your network. This
More informationConfiguring NXT Hardware with Mercury Inside into Doors.NET TM Application Note
1.0 Installing the Mercury SCP Gateway The MSC/SCP gateway must be installed to interface with Mercury hardware. This gateway must be chosen during the installation of the software, or it can be added
More informationInstalling Novell Client Software (Windows 95/98)
Installing Novell Client Software (Windows 95/98) Platform: Windows 95/98 Level of Difficulty: Intermediate The following procedure describes how to install the Novell Client software. This software allows
More informationAcqKnowledge for Windows: Upgrade for 1+MP150s and Domain Network Access or Direct Communication Setup (Domain/Non-domain)
APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 208: AcqKnowledge for Windows: Upgrade for 1+MP150s and
More informationTDP43ME NetPS. Network Printer Server. Control Center. for Ethernet Module
Panduit Corp. 2010 TDP43ME NetPS PA26306A01 Rev. 01 11-2010 Network Printer Server Control Center for Ethernet Module NOTE: In the interest of higher quality and value, Panduit products are continually
More informationOperating Instructions
Operating Instructions (For Setting Up) Digital Imaging Systems Installation Overview Model No. DP-8060 / 8045 / 8035 Table of Contents Setting Your Machine Installation Overview General Installation Overview...
More informationQuick Installation Guide DAP-1360. Wireless N 300 Access Point & Router
DAP-1360 Wireless N 300 Access Point & Router BEFORE YOU BEGIN Delivery Package Access point DAP-1360 Power adapter DC 12V Ethernet cable (CAT 5E) (brochure). If any of the items are missing, please contact
More informationSelf Help Guide IMPORTANT! F5D7330 - Setting Up An Ad Hoc Connection. Please read the following carefully;
IMPORTANT! This Guide refers to the following Products: F5D7330 - Setting Up An Ad Hoc Connection Please read the following carefully; Synopsis: This guide is designed to assist in you in forming an ad
More informationScan to SMB(PC) Set up Guide
Scan to SMB(PC) Set up Guide Regarding Trade Names Windows is a registered trademark of Microsoft Corporation in the U.S.A. and/or other countries. Windows XP and Windows Vista are trademarks of Microsoft
More informationSymphony Network Troubleshooting
Symphony Network Troubleshooting Step 1) Review the Networking 101 presentation on the CD included with the Symphony. A basic understanding of networks is essential to this procedure. Step 2) Identify
More informationSavvius Insight Initial Configuration
The configuration utility on Savvius Insight lets you configure device, network, and time settings. Additionally, if you are forwarding your data from Savvius Insight to a Splunk server, You can configure
More informationSQL Server 2008 R2 Express Edition Installation Guide
Hardware, Software & System Requirements for SQL Server 2008 R2 Express Edition To get the overview of SQL Server 2008 R2 Express Edition, click here. Please refer links given below for all the details
More informationWindows Peer-to-Peer Network Configuration Guide
Windows Peer-to-Peer Network Configuration Guide Windows Peer-to-Peer Network Configuration Guide for CCC Pathways Copyright 2008 by CCC Information Services Inc. All rights reserved. No part of this publication
More informationConfiguring Windows 7 64 bit for AutoVISION
This document will describe how to configure a 64 bit version of Windows 7 Professional, Ultimate or Enterprise to utilize the Windows XP Mode (Virtual PC) capabilities to allow AutoVISION to be used in
More informationHow to set up HotFolders and Workflows
How to set up HotFolders and Workflows HotFolders 1 The basis: HotFolders acting like a FileManager 1 An example: HotFolders and the Images bar 2 Printing from a Windows client 4 Workflows 5 Printing Workflow
More informationAllworx Installation Course
VPN Hello and welcome. In the VPN section we will cover the steps for enabling the VPN feature on the Allworx server and how to set up a VPN connection to the Allworx System from your PC. Page 1 VPN The
More informationQuick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012
Quick Note 32 Using Digi RealPort with a Digi TransPort Router UK Support September 2012 1 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions... 3 1.3 Version... 3 2 Configuration & scenario...
More informationSetting up Sharp MX-Color Imagers for Inbound Fax Routing to Email or Network Folder
Setting up Sharp MX-Color Imagers for Inbound Fax Routing to Email or Network Folder MX-2300, MX-2600, MX-2700, MX-3100, MX-3501, MX-4501, MX-5500, MX-6200, MX-6201, MX-7000, MX-7001, *MX-M850, *MX-M950,
More informationUsing Cisco UC320W with Windows Small Business Server
Using Cisco UC320W with Windows Small Business Server This application note explains how to deploy the Cisco UC320W in a Windows Small Business Server environment. Contents This document includes the following
More information