Size A=100 B=30 C=76 D=3 Mini Door Thickness (mm) 44 Door Mass (Kg) 120 Classification 13. Grade 304-SSS, PSS, PB Grade 316 KH.

Size: px
Start display at page:

Download "Size A=100 B=30 C=76 D=3 Mini Door Thickness (mm) 44 Door Mass (Kg) 120 Classification 13. Grade 304-SSS, PSS, PB Grade 316 KH."

Transcription

1 Product ID: KH.1001 Name: Hinge Size A=100 B=30 C=76 D=3 Mini Door Thickness (mm) 44 Door Mass (Kg) 120 Classification 13 Description Ball Bearing Finish Grade 304-SSS, PSS, PB Grade 316 KH SSS, PSS, PB Fixing (mm) WS X 30 - Template Options Radius Corner - KH.1003 Security Dog Bolt KH.1004 CONFORMITY No KH CE AC0049

2 CERTIFICATE OF APPROVAL No CF 5247 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of KCC ARCHITECTURAL Unit 1, Westgate Business Park, Ballymount Industrial Estate, Dublin 24 Tel: Fax: Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT KCC Architectural Stainless Steel Hinges TECHNICAL SCHEDULE TS24 The Contribution of Single Axis Hinges to the Fire Resistance of Door Assemblies Signed and sealed for and on behalf of CERTIFIRE Sir Ken Knight Issued: 28 th May 2014 Chairman - Management Council Valid to: 19 th December 2018 Page 1 of 5 This certificate is the property of Warrington Certification Limited, part of Exova (UK) Ltd. Registered office: Lochend Industrial Estate, Newbridge, Midlothian, EH28 8PL, UK. Registered in Scotland, No. SC 70429

3 CERTIFICATE No CF 5247 KCC ARCHITECTURAL KCC Architectural Stainless Steel Hinges 1. This approval relates to the use of the KCC Architectural stainless steel, single axis hinges referenced KH1001 and KH1001RC in contributing to the fire resistance performance of timber based doorsets, as defined by EN or BS 476: Part 22, for periods of 20 and 30 minutes integrity or metallic based doorsets, for periods of 30, 60, 90, 120 or 240 minutes integrity. Subject to the undermentioned conditions, the doorsets will meet the relevant requirements of BS 5588 for doorsets when used in accordance with the provisions therein. 2. This certification is designed to demonstrate compliance of the product or system specifically with Approved Document B (England and Wales), Section D of the Technical Standards (Scotland), Technical Booklet E (N. Ireland). If compliance is required to other regulatory or guidance documents there may be additional considerations or conflict to be taken into account. 3. The hinges are approved on the basis of: i) Initial type testing to EN 1935 ii) A design appraisal against TS24 iii) Certification of quality management system to ISO 9001: iv) Inspection and surveillance of factory production control v) On-going audit testing in accordance with EN 1935 requirements 4. The products are stainless steel, single axis hinges, for use on various classes of doorsets. The hinges are Class This certification relates only to the following hinge variants: Hinge Dimensions Maximum Leaf Weight KH x 76 x 3mm 120 kg KH1001RC 102 x 76 x 3mm 120 kg 6. This approval relates to the above hinges used with latched or unlatched single-leaf or double-leaf door assemblies consisting of timber faced and edged leaves with timber, cellulosic or mineral cores and in timber frames (Code ITT) not less than 45 mm thick. The door frame shall consist of timber with a minimum density of 450 kg/m³ (with leaf to frame gaps less than 3mm), for FD20, FD30, E30 and EI30 applications. The hinges must be bedded onto 1 mm of mono ammonium phosphate material behind both blades. Page 2 of 5 Signed Issued: 28 th May 2014 Valid to: 19 th December 2018 This certificate is the property of Warrington Certification Limited, part of Exova (UK) Ltd. Registered office: Lochend Industrial Estate, Newbridge, Midlothian, EH28 8PL, UK. Registered in Scotland, No. SC 70429

4 CERTIFICATE No CF 5247 KCC ARCHITECTURAL KCC Architectural Stainless Steel Hinges 7. This approval also relates to the above hinges used with latched or unlatched single-leaf or double-leaf door assemblies consisting of metallic faced and edged leaves hung within metallic frames (Codes MM and IMM) not less than 45 mm thick, for up to FD240, E240 and EI240 applications. 8. The above hinges may only be fitted to previously tested timber door assemblies when fitted in the manner described in this certificate and when particular aspects of the door assembly are maintained. 9. Hinges shall only be fitted using the fixings supplied by the hinge manufacturer. 10. The doorset, including door frame and associated building hardware, should be either CERTIFIRE approved for the relevant application and classification or the doorset, including door frame and associated building hardware, should have achieved at least 30 minutes fire resistance when tested, or subsequently assessed to BS 476: Part 22: 1987 or EN In either case regard should be paid to the maximum door mass permitted to be used with the hinge (see classification). 11. Timber doorsets shall be installed in accordance with BS 8214: The approval relates to on-going production. Product and/or its immediate packaging is name or name and mark, together with the CERTIFIRE certificate number and application where appropriate. Page 3 of 5 Signed Issued: 28 th May 2014 Valid to: 19 th December 2018 This certificate is the property of Warrington Certification Limited, part of Exova (UK) Ltd. Registered office: Lochend Industrial Estate, Newbridge, Midlothian, EH28 8PL, UK. Registered in Scotland, No. SC 70429

5 CERTIFICATE No CF 5247 KCC ARCHITECTURAL KCC Architectural Stainless Steel Hinges Matrix of acceptable doorset types Approved Door Type Class IMM MM TT ITT ITM ITC FD20 FD30 FD60 FD120 FD240 E 20 EI 20 E 30 EI 30 E 60 EI 60 E 90 EI 90 E 120 EI 120 E 240 EI 240 See CERTIFIRE Technical Schedules for designation of doorset types i.e. ITT etc. Key: - Approved - Not approved Page 4 of 5 Signed Issued: 28 th May 2014 Valid to: 19 th December 2018 This certificate is the property of Warrington Certification Limited, part of Exova (UK) Ltd. Registered office: Lochend Industrial Estate, Newbridge, Midlothian, EH28 8PL, UK. Registered in Scotland, No. SC 70429

6 CERTIFICATE No CF 5247 KCC ARCHITECTURAL KCC Architectural Stainless Steel Hinges Scope of Approval: The hinges may be fitted to doorsets without intumescent protection for up to 20 minutes integrity. All applications apply to glazed and unglazed doorsets. Both blades of the hinges must be bedded onto 1 mm of mono ammonium phosphate material when used with TT or ITT doorsets. The door frame of TT and ITT doorsets shall consist of timber with a minimum density of 450 kg/m³ (with leaf to frame gaps less than 3mm). Classification codes The approval provides the following classifications: KH1001 & KH1001RC Further Information Further information regarding the details contained in this certificate may be obtained from KCC Architectural (Tel: ). Further information regarding CERTIFIRE certification and other approved products can be obtained from CERTIFIRE (Tel: ). Page 5 of 5 Signed Issued: 28 th May 2014 Valid to: 19 th December 2018 This certificate is the property of Warrington Certification Limited, part of Exova (UK) Ltd. Registered office: Lochend Industrial Estate, Newbridge, Midlothian, EH28 8PL, UK. Registered in Scotland, No. SC 70429

7 Exova Warringtonfire Holmesfield Road Warrington WA1 2DS United Kingdom T : +44 (0) F : +44 (0) E : W: Title: The Fire Resistance Performance of Doorsets Incorporating Various Items of Frisco Door Furniture WF Assessment Report No: Issue 4 Prepared for: Frisco (UK) Sales Ltd Unit 14 Pindar Road Essex Road Hoddesdon Herts EN11 0DE Date: 8 th February 2008 Registered Office: Exova (UK) Ltd, Lochend Industrial Estate, Newbridge, Midlothian EH28 8PL United Kingdom. Reg No.SC 70429

8 WF Assessment Report No Issue 4 Page 13 of /2/3 The models 14101, and are all mild steel ball bearing butt hinges of identical design to the tested These models differ from each other only in respect of their finishes which are satin chrome, polished chrome and electro brass respectively. The change of material from that of the tested mild steel hinge to mild steel for the proposed hinge models is not considered to have any negative influence on the performance of the hinges when used in the proposed application with 30 minute fire resisting timber based doors. The proposed hinges are therefore positively appraised. Eclipse Hinge Range Steel Based Doors Of the range of hinges previously discussed, several models are currently Certifire approved (CF336). Of these, the following models have additional approval for use with steel based doorsets for fire resistance periods of up to 240 minutes , 14860, PK858, PK860, 14854, 14853, PK854, PK853, 14882, PK882, 14861, 14869, 14872, 14879, 14883, 14884, 14866, 14888, and Insignia 14929, 14930, 14931, 14932, PK929, PK930, PK931 & PK932. The above hinges are all of stainless steel construction and have been approved for use with steel based doorsets for fire resistance periods of up to 240 minutes. It is therefore considered acceptable that the scope of use for these hinge models, when fitted to steel based doorsets, may also be included in this appraisal. The following requirements of the doorset are however considered to be essential: The doorset must have provided the required 20, 30, 60, 120 or 240 minute integrity performance when tested at a UKAS accredited laboratory in accordance with BS 476: Part 22: 1987 or EN : 2000, be assessed for the required period by Exova Warringtonfire or be CERTIFIRE approved for the required period. The tested/assessed doorset as described above must have been tested or assessed in the required configuration i.e. number of leaves and action. The maximum door mass shall be commensurate with the class of the relevant hinge and shall not be exceeded. A full list of the positively appraised Eclipse Hinge Range items is included within the Annex to this report. Eclipse Security Range The Eclipse Security Range incorporates several mortice latch/locks the dimensions and materials of which are comparable to those of the Eclipse ez-r sashlock included within the test referenced WF No This test demonstrated that the inclusion of the Eclipse ez-r sashlock had no deleterious effects upon the tested timber based doorset for in excess of 60 minutes and based upon this it is considered that the proposed Black Antique Range locks may be included with suitable timber based doorsets, as detailed below:

9 WF Assessment Report No Issue 4 Page 37 of 48 Eclipse Hinge Range Name Code Integrity with timber doors Additional Information Ball Bearing Hinges 4 Ball Bearing Hinges PK858 PK PK854 PK PK to to Up to 60 minutes Suitable doorset specifications are described on Page 12 of this report Radius Corner Ball Bearing Butt Hinges Ball Bearing Butt Hinges Security Butt Hinges Washered Hinges Insignia Hinges PK920 PK930 PK931 PK932

10 Page 1 of 2 EC CERTIFICATE OF CONFORMITY Number: CPD - AC0049 In compliance with Directive 89/106/EEC of the Council of European Communities of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Construction Products Directive - CPD), amended by the Directive 93/68/EEC of the Council of European Communities of 22 July 1993, it is confirmed that the following products are subject to factory production control procedures and are submitted by the manufacturer to further testing of samples taken at the factory in accordance with a prescribed test plan. The stated Notified Certification Body has performed the initial type-testing for the relevant characteristics of the product, has conducted the initial inspection of the factory and the factory production control, and is responsible for the continuous surveillance, assessment and approval of the factory production control. construction product : Eclipse range detailed on page 2 placed on the market by: Company: Address: Frisco UK Unit 14,Essex Road, Hoddeson, Hertfordshire, EN11 0AA product classification: * intended use: For use on fire / smoke compartmentation doors and on escape route doors This document certifies that all the provisions concerning the attestation of conformity and product performance described in Annex ZA of the product standard EN 1935 : 2002 were applied and that the product fulfils all the prescribed requirements. Notified Certification Body: Warrington Certification Ltd EC Reference Number: 1121 This certificate was first issued on 28/01/2004 revised on 01/04/2010 and remains valid as long as the conditions laid down in the harmonised technical specification above, or the product design, or the manufacturing conditions in the factory, or the FPC itself are not modified significantly, or at the latest 31/03/2015. Manager Warrington Certification Ltd. References: Mechanical test evidence: , , , Fire test evidence: , , and and Factory references: J/006 Classification report: N/a * The referenced reports detail the precise field of application for fire/smoke door use

11 Page 2 of 2 EC CERTIFICATE OF CONFORMITY Number: CPD AC0049 Hinge reference Description x 3 x 3mm 304 Satin Stainless steel x 3 x 3mm 304 Polished Stainless steel x 3 x 3mm Brass plated with radiused corners x 3 x 3mm Brass Plated stainless steel x 3 x 3mm 304 Satin Stainless steel with radiused corners x 3 x 3mm 304 Polished Stainless steel with radiused corners x 3 x 3mm 304 Satin Stainless steel with radiused corners x 3 x 3mm 304 Polished Stainless steel with radiused corners x 3 x 3mm 316 Satin Stainless steel x 3 x 3mm 316 Polished Stainless steel Notified Certification Body: Warrington Certification Ltd EC Reference Number: 1121 This certificate was first issued on 28/01/2004 revised 01/04/2010 and remains valid as long as the conditions laid down in the harmonised technical specification above, or the product design, or the manufacturing conditions in the factory, or the FPC itself are not modified significantly, or until 31/03/2015, whichever is the latest. Manager Warrington Certification Ltd.

12 KH1001 Construction Products Regulation 2011 DECLARATION OF PERFORMANCE DoP No. KCC Unique identification code of the product type: Single Axis Hinge 2. Type, batch or serial number or any other element allowing identification of the construction product as required under Article 11(4) of the CPR: KH Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: For use on fire and smoke compartmentation doors, when fitted in accordance with the manufacturer's fitting instructions. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under Article 11(5): KCC Architectural, Unit 1, Westgate Business Park, Ballymount, Dublin 12, Ireland Tel: +353 (0) Web: 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2): N/A 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in CPR, Annex V: System 1 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard. EN 1935 : 2002 Notified product certification body No performed the type testing and issued test reports. 8. European Technical Assessment: N/A 1

13 KH Declared Performance Figure The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Chris Kilpatrick Managing Director Date of issue: 1 st July 2013 KCC Architectural, Unit 1, Westgate Business Park, Ballymount, Dublin 12 Ireland 2