NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA NAND FLASH D'UNE E-MGD AVEC PC INSTALLER EN RELEASE 5.

Size: px
Start display at page:

Download "NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA NAND FLASH D'UNE E-MGD AVEC PC INSTALLER EN RELEASE 5."

Transcription

1 COMMUNICATION TECHNIQUE N TC0521 Ed. 01 OmniPCX Enterprise Nb de pages : 17 Date : URGENTE NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA Cette communication technique a pour but de fournir une procédure de rechargement des binaires e- MGD en R5.1 dans le cas d'une altération de la NAND Flash d'une e-mgd. 1

2

3 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise SOMMAIRE 1. BUT EFFACEMENT ET REFORMATAGE DE LA NAND FLASH E-MGD RECHARGEMENT DES BINAIRES E-MGD...5 Ed. 01 / TC0521

4 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA TC Ed. 01 /

5 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 1. BUT Cette communication technique a pour but de fournir une procédure de rechargement des binaires e-mgd en R5.1dans le cas d'une altération de la NAND Flash d'une e-mgd. Le rechargement de la NAND Flash d'une e-mgd avec l'omnipcx Enterprise PC Installer s'effectue en deux phases : 1 Effacement et reformatage de la NAND Flash e-mgd. 2 Rechargement des binaires e-mgd. 2. EFFACEMENT ET REFORMATAGE DE LA NAND FLASH E-MGD 1 Connecter la carte GD/GA et le PC Serveur avec un câble Ethernet croisé. 2 Démarrer l'omnipcx Enterprise PC Installer V2.15. Choisir le type d'installation Binaire GD/GA dans le menu Type d installation. Cliquer sur Valider dans la fenêtre Paramètres d installation. Les binaires e-mgd (dépendants de la version) doivent être présents dans le répertoire /dhs3mgr/"version"/pcmao/boot_res/dhs3bin/downbin/emg. Ed. 01 / TC0521

6 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA 3 Démarrer la carte GD/GA en mode LOLA. Positionner les dip switchs 1, 2 et 4 sur ON, le dip switch 3 sur OFF. Démarrer la carte GD/GA en Position Contrôleur (Position 0 du Rack). Dans ce mode, le transfert des fichiers peut être visualisé dans la fenêtre Paramètres du client de l'omnipcx Enterprise PC Installer. TC Ed. 01 /

7 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 4 Les différentes phases d'effacement et de reformatage peuvent être visualisées par la LED CPU de la carte GD/GA : Phase du bios 2 x ON/OFF (250ms)/ 1 OFF ( 2 s) Phase de chargement du Linux.ram 4 x ON/OFF(250ms)/ 1 OFF ( 2 s) Phase d'effacement et de formatage de la NAND FLASH Fixe ON Phase de fin de formatage de la NAND FLASH Clignotement rapide (50 ms/ 50 ms) 5 La fin de formatage de la FLASH est visualisée sur le port de configuration V24 par le message : Welcome to PeeWeeLinux (none) login: 6 Arrêter la carte GD/GA avec l'interrupteur On/Off et attendre que la LED power passe au rouge fixe. 7 Arrêter l'application OmniPCX Enterprise PC Installer sur le PC Serveur. 3. RECHARGEMENT DES BINAIRES E-MGD 1 Redémarrer l'omnipcx Enterprise PC Installer V2.15. Choisir le type d'installation Binaire GD/GA dans le menu Type d installation. Cliquer sur Valider dans la fenêtre Paramètres d installation ; voir point 2 du 2) 2 Démarrer la carte GD/GA en mode GD. Positionner le dip switch 2 sur ON, les dip switchs 1, 3 et 4 sur OFF. Démarrer la carte GD/GA en Position Contrôleur (Position 0 du Rack). Dans ce mode une visualisation du transfert des fichiers est possible sur le port de configuration V24 ( N-1) et également dans la fenêtre Paramètres du client de l'omnipcx Enterprise PC Installer. Ed. 01 / TC0521

8 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA TC Ed. 01 /

9 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise Exemple de rechargement correct sur le port de configuration V24 Alize BIOS Monitor *** BIOS Version 3EH30227DQAA bios100/ *** *** Generated on Mar/20/2003 at 09:21 *** memory test started lng= with 0 YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW! running flash(soldered=1 socket=0)=1,bioscase:4,biosv24:0,verrou=1,algonor=1,size=1,base=3ff80000 DIMM characteristics->: JEDEC Manu ID:. Memory type(edo,fpm..):0x04 # of row address:12 # of col address 10 # of module row 1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI:scan_bus for bus 0 PCI:bus=00h,devfn=00h,[vendor:device]=[1022h/3000h] PCI:bus=00h,devfn=60h,[vendor:device]=[100bh/0020h] PCI:bus=00h,devfn=98h,[vendor:device]=[1064h/2101h] PCI:scan_buses with 00h secondary buses PCI:command =000003ffH for device 00:00 PCI: Assigning I/O space fc00-fcff for 00:60 BAR= PCI:Assign memory space bffff000h to bfffffffh for device 00:60 PCI:command =000003ffH for device 00:60 PCI:Assign memory space bfffd000h to bfffdfffh for device 00:98 PCI: Assigning I/O space fd00-fd1f for 00:98 BAR= PCI: Unable to handle I/O allocation for 00:98 (ff04) BAR= PCI:command =000003ffH for device 00:98 assigning irq10 to xchange B0 = 17 DRCTMCTL = 1e DRCCTL = 18 DBCTL = 11 Set external RTC Set Internal RTC No external RTC detected CMOS is available Xchange PCI mem base OK: Xchange PCI IO base OK: Xchange irq OK: 0a PCI command read for natsemi : PCI Master Bit Setting... pci_command set to: f 002f 00ef 0037, IRQ 12 eth0: Transceiver status 0x advertising e1 Flashfx version: NAND flash drive No. 0 successfully mounted NAND Flash Comfiguration: CPU size : 32 MBytes free spare blocks: 38 XMEM size : 0 MBytes NAND Flash Details: chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=512 time :sec=09,min=12,hour=11,dow=02,date=15,month=12,year=00 time :sec=12,min=12,hour=11,dow=02,date=15,month=12,year=00 ALIZE informations : Memory Detected : Ko Flash Detected DaughterBoard Detected DSP Voip Found : 1 XCHANGE Detected XCHANGE Chip Initialization OK Ethernet Found : 1 Ethernet Chip Initialization OK Hard Disk Not Detected PCM11 selected CPU at 133 mhz check lock RTC value of DIL switch 02 Ed. 01 / TC0521

10 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA test the BATMODE Static Boot from hard disk #0 (3) unable to boot on DISK : Static Boot from No Boot Device selected (0) Static Boot from flash NAND mother (1) unable to boot on NAND flash drive 0 unable to boot on flash NAND Static Boot from ethernet (4) eth0: Setting 1 (0 half 1 full) based on negotiated link capability. IP address determination ============================ BOOTP request in progress -> 0:80:9f:2f:ef:37 *RcvTO,TOIPRcv,Bootp resp IP addr src : bootp server and TFTP server are the same TFTP server IP addr ( siaddr) : eth source address=0:50:da:81:ef:24 bootfile = /DHS3bin/downbin/emg/binmgstart Netmask : Our Hostname : OXE_1 ( ) Domain name : lcatel.a My IP address My SUBNET mask TFTPLOAD STARTED using ip= Bootp Server PARIS-A63YI55YS - File Name /DHS3bin/downbin/emg/binmgstart size of last packet: 141 TFTPLOAD COMPLETE - file size 141 cmd received : /DHS3bin/downbin/emg/binmgvmlinux;763904;BIN; ; /DHS3bin/downbin/emg/binmgrdimg; ;RAMDISK; ;0 boot;0;boot;0; size of file loaded : dH at H j= 0 file-fct type= 7,file name= /DHS3bin/downbin/emg/binmgvmlinux,length= ,address= start= j= 1 file-fct type= 1,file name= /DHS3bin/downbin/emg/binmgrdimg,length= ,address= start=0 j= 2 file-fct type= 5,file name= boot,length= 0,address=0 start= j= 3 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 4 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 5 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 6 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 7 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 8 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 9 file-fct type= 0,file name=,length= 0,address=0 start=0 config action number=3 TFTPLOAD STARTED using ip= Bootp Server PARIS-A63YI55YS - File Name /DHS3bin/downbin/emg/binmgvmlinux......size of last packet: 14 TFTPLOAD COMPLETE - file size WARNING: downloaded size file # from command file TFTPLOAD STARTED using ip= Bootp Server PARIS-A63YI55YS - File Name /DHS3bin/downbin/emg/binmgrdimg size of last packet: 187 TFTPLOAD COMPLETE - file size =total packets received 11584=total packets transmitted =total bytes received =total bytes transmitted 0=bad packets received 0=packet transmit problems 0=no space in linux buffers 0=no space available in linux 0=multicast packets received 0=collisions 0=length_errors TC Ed. 01 /

11 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 0=receiver ring buff overflow 0=recved pkt with crc error 0=recv'd frame alignment error 0=recv'r fifo overrun 0=receiver missed packet 0=tx_aborted_errors 0=tx_carrier_errors 0=tx_fifo_errors 0=tx_heartbeat_errors 0=tx_window_errors 0=rx_compressed 0=tx_compressed start kernel at Shutdown of the interface 0 = init ethernet interface 1 not done Watch dog started Linux version rtl (gcc version (release)) #45 Fri Jan 31 13:52:58 MET 2003 Calibrating delay loop BogoMIPS Memory: k/131072k available (632k kernel code, 412k reserved, 1584k data, 36k init) Checking if this processor honours the WP bit even in supervisor mode... Ok. ShutOK cleared! Dentry hash table entries: (order 5, 128k) Buffer cache hash table entries: (order 7, 512k) Page cache hash table entries: (order 5, 128k) CPU: AMD 486 DX/4-WB stepping 04 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP TCP: Hash tables configured (ehash bhash 65536) 802.1Q VLAN Support v1.0 (c) 2000 Ben Greear (GPL) vlan Initialization complete. Starting kswapd v 1.5 Serial driver version 4.27 with no serial options enabled ttys00 at 0x03f8 (irq = 4) is a 16550A ttys01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured RAM disk driver initialized: 16 RAM disks of 20480K size RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 36k freed Warning: unable to open an initial console. Initial console created for init RTLinux Extensions Loaded (http://www.fsmlabs.com/) Starting watchdog timer daemon using /dev/rtf3 modprobe: modprobe: Can't locate module char-major-4 INIT: version 2.78 booting Remounting root read-write... modprobe: modprobe: Can't locate module char-major-4 e-mgd board found - setting up ramdisk Remount - Forces the media to be remounted Datalight FlashFx V Copyright (c) Patent US# Disk Remounted e2fsck 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09 /dev/fla: clean, 11/7776 files, 1000/31062 blocks /dev/fla on /mnt/flash type ext2 (rw) INIT: Entering runlevel: 3 e-mgd version 16.7 Media Gateway Software R5.1 loading.. No password file found - using default password list Network configured successfully. Duplex mode : auto-negociation BIOS updater is now working... getting current version information Ed. 01 / TC0521

12 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA Check if we need to update with bios 3EH30227DQAA bios100/ Reboot after bios update is enabled RetrieveFlashNorInfo NOR VERSION : Bios Version in soldered NOR flash : 3EH30227DQAA bios100/ len = 28 - Flash Nor Informations - Flash AMD Size : 512 Kbytes Number of sectors : CompareBiosVersions CURRENT= FILE= ******************************* * NO bios Update is necessary * ******************************* Basic registers of MII PHY #1: d c21 05e1 45e Link status: active. loading modules - please wait... Real-Time Linux Dynamic Memory Manager 4.00 RTLinux System Call loaded Starting USER_PROCCES using fifo 7 6 Waiting for User Process registration Starting VG_PROCCES using fifo 5 4 Waiting for Vg Process registration Starting monitor using fifos 1/2 Alcatel kernel module loading...(break=0) Application User Process registered Application VG Process registered Main task created thread_id=0xc5291e00 stack address=0xc528cd58 stack bottom address = 0xc watchdogd now in real time mode DSP Manager OK Fast Socket Initialization... Ok ============ continue_rack_init ============== DIL SWITCH VALUE = 0x Ko - BUFFER ALLOCATED MGD - RACK MAC : IP : net mask : gateway : tftp server : call server : default crystal number : 3 (Dynamic allocation) vlan id : -1 default priority : 0 default dscp : 0 duplex mode : auto-negociation Module MG Loaded watchdogd now in normal mode RTLinux System Load 1.00 init_module GPA ->insmod GPA Module GPA loaded Module APA loaded Module SLAC loaded Module DDI loaded Module UAI loaded Module SLI loaded Insert INTX module Insert ISDN module Module BRA loaded Module PRA loaded Module PRACCS loaded Module PRA_T1CAS loaded Module PRA_E1CAS loaded ->init_module emga ==> emgd_emga & emgd_gpa module types created! Module emgd_emga loaded Module emgd_gpa loaded Module MIX loaded Module ATL loaded Module RESCUE loaded PUC_device registered Module DPNSS loaded Module DSPx_LOAD loaded Module UASIM loaded TC Ed. 01 /

13 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise /mnt/flash/local/boot_from.cfg not found. Assuming boot from ethernet Downloading /DHS3bin/downbin/emg/binmg from Downloading binmgrdimg and binmglinux Downloading /DHS3bin/downbin/emg/binmgrdimg from Downloading /DHS3bin/downbin/emg/binmglinux from binmglinux and binmgrdimg successfully downloaded Copying binmg, binmglinux, and binmgrdimg in flash. This process may take several minutes. Please do NOT reboot during the flashing process. watchdogd now in real time mode GRUB version (640K lower / 4096K upper memory) [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ESC at any time exits. ] grub> install=(vd0)/boot/pstage1 d (vd0) (vd0)/boot/stage2 0x8000 p (vd0)/boot/ grub.cnf grub> quit Rebooting in 5 seconds to try the new version. Reboot on Download new binaries INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal Alcatel kernel module cleanup...ok Saving e-mgd configuration files... Saving System Clock in Hardware Clock... No backtrace Sending all processes the TERM signal... Sending all processes the KILL signal.. Unmounting file systems Restarting system. ShutOK cleared! Alize BIOS Monitor *** BIOS Version 3EH30227DQAA bios100/ *** *** Generated on Mar/20/2003 at 09:21 *** memory test started lng= with 0 YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW! running flash(soldered=1 socket=0)=1,bioscase:4,biosv24:0,verrou=1,algonor=1,size=1,base=3ff80000 DIMM characteristics->: JEDEC Manu ID:. Memory type(edo,fpm..):0x04 # of row address:12 # of col address 10 # of module row 1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI:scan_bus for bus 0 PCI:bus=00h,devfn=00h,[vendor:device]=[1022h/3000h] PCI:bus=00h,devfn=60h,[vendor:device]=[100bh/0020h] PCI:bus=00h,devfn=98h,[vendor:device]=[1064h/2101h] PCI:scan_buses with 00h secondary buses PCI:command =000003ffH for device 00:00 PCI: Assigning I/O space fc00-fcff for 00:60 BAR= PCI:Assign memory space bffff000h to bfffffffh for device 00:60 PCI:command =000003ffH for device 00:60 PCI:Assign memory space bfffd000h to bfffdfffh for device 00:98 PCI: Assigning I/O space fd00-fd1f for 00:98 BAR= PCI: Unable to handle I/O allocation for 00:98 (ff04) BAR= PCI:command =000003ffH for device 00:98 assigning irq10 to xchange B0 = 17 DRCTMCTL = 1e DRCCTL = 18 DBCTL = 11 Set external RTC Set Internal RTC No external RTC detected CMOS is available Xchange PCI mem base OK: Xchange PCI IO base OK: Xchange irq OK: 0a PCI command read for natsemi : PCI Master Bit Setting... pci_command set to: f 002f 00ef 0037, IRQ 12. eth0: Transceiver status 0x advertising e1 Flashfx version: Ed. 01 / TC0521

14 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA NAND flash drive No. 0 successfully mounted NAND Flash Comfiguration: CPU size : 32 MBytes free spare blocks: 38 XMEM size : 0 MBytes NAND Flash Details: chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=512 time :sec=42,min=15,hour=11,dow=02,date=15,month=12,year=00 time :sec=45,min=15,hour=11,dow=02,date=15,month=12,year=00 ALIZE informations : Memory Detected : Ko Flash Detected DaughterBoard Detected DSP Voip Found : 1 XCHANGE Detected XCHANGE Chip Initialization OK Ethernet Found : 1 Ethernet Chip Initialization OK Hard Disk Not Detected PCM11 selected CPU at 133 mhz check lock RTC value of DIL switch 02 test the BATMODE Static Boot from hard disk #0 (3) unable to boot on DISK : Static Boot from No Boot Device selected (0) Static Boot from flash NAND mother (1) BOOT Sector Found on NAND Flash Drive #0 Shutdown of the interface 0 = init ethernet interface 1 not done Watch dog started Linux version rtl (gcc version (release)) #45 Fri Jan 31 13:52:58 MET 2003 Calibrating delay loop BogoMIPS Memory: k/131072k available (632k kernel code, 412k reserved, 1584k data, 36k init) Checking if this processor honours the WP bit even in supervisor mode... Ok. ShutOK cleared! Dentry hash table entries: (order 5, 128k) Buffer cache hash table entries: (order 7, 512k) Page cache hash table entries: (order 5, 128k) CPU: AMD 486 DX/4-WB stepping 04 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP TCP: Hash tables configured (ehash bhash 65536) 802.1Q VLAN Support v1.0 (c) 2000 Ben Greear (GPL) vlan Initialization complete. Starting kswapd v 1.5 Serial driver version 4.27 with no serial options enabled ttys00 at 0x03f8 (irq = 4) is a 16550A ttys01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured RAM disk driver initialized: 16 RAM disks of 20480K size RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 36k freed Warning: unable to open an initial console. Initial console created for init RTLinux Extensions Loaded (http://www.fsmlabs.com/) Starting watchdog timer daemon using /dev/rtf3 modprobe: modprobe: Can't locate module char-major-4 INIT: version 2.78 booting Remounting root read-write... modprobe: modprobe: Can't locate module char-major-4 e-mgd board found - setting up ramdisk TC Ed. 01 /

15 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise Remount - Forces the media to be remounted Datalight FlashFx V Copyright (c) Patent US# Disk Remounted e2fsck 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09 /dev/fla: clean, 48/7776 files, 6502/31062 blocks /dev/fla on /mnt/flash type ext2 (rw) INIT: Entering runlevel: 3 e-mgd version 16.7 Media Gateway Software R5.1 loading... No password file found - using default password list *** BIOS startup mode (2) forbidden when boot on flash filesystem *** *** Switch to dynamic mode (1) *** First time boot - disabling vlan tagging Internet Software Consortium DHCP Client 2.0pl5 Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium. All rights reserved. Please contribute if you find this software useful. For info, please visit Listening on Socket/eth0 Sending on Socket/eth0 DHCPDISCOVER on eth0 to port 67 interval 4 DHCPOFFER from DHCPREQUEST on eth0 to port 67 DHCPACK from No option router given! DHCP server: Obtained IP address: Netmask: Gateway: Tftp server: Lease time: 1800 bound to renewal in 900 seconds. Duplex mode : auto-negociation BIOS updater is now working... getting current version information Check if we need to update with bios 3EH30227DQAA bios100/ Reboot after bios update is enabled RetrieveFlashNorInfo NOR VERSION : Bios Version in soldered NOR flash : 3EH30227DQAA bios100/ len = 28 - Flash Nor Informations - Flash AMD Size : 512 Kbytes Number of sectors : CompareBiosVersions CURRENT= FILE= ******************************* * NO bios Update is necessary * ******************************* Basic registers of MII PHY #1: d c21 05e1 45e Link status: active. loading modules - please wait... Real-Time Linux Dynamic Memory Manager 4.00 RTLinux System Call loaded Starting USER_PROCCES using fifo 7 6 Waiting for User Process registration Starting VG_PROCCES using fifo 5 4 Waiting for Vg Process registration Starting monitor using fifos 1/2 Alcatel kernel module loading...(break=0) Application User Process registered Application VG Process registered Main task created thread_id=0xc5252e00 stack address=0xc524cd58 stack bottom address = 0xc watchdogd now in real time mode DSP Manager OK Fast Socket Initialization... Ok ============ continue_rack_init ============== DIL SWITCH VALUE = 0x Ko - BUFFER ALLOCATED MGD - RACK MAC : 00:80:9f:2f:ef:37 Ed. 01 / TC0521

16 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE IP : net mask : gateway : tftp server : call server : default crystal number : 3 (Dynamic allocation) vlan id : -1 default priority : 0 default dscp : 0 duplex mode : auto-negociation Module MG Loaded watchdogd now in normal mode RTLinux System Load 1.00 init_module GPA ->insmod GPA Module GPA loaded Module APA loaded Module SLAC loaded Module DDI loaded Module UAI loaded Module SLI loaded Insert INTX module Insert ISDN module Module BRA loaded Module PRA loaded Module PRACCS loaded Module PRA_T1CAS loaded Module PRA_E1CAS loaded ->init_module emga ==> emgd_emga & emgd_gpa module types created! Module emgd_emga loaded Module emgd_gpa loaded Module MIX loaded Module ATL loaded Module RESCUE loaded PUC_device registered Module DPNSS loaded Module DSPx_LOAD loaded Module UASIM loaded binmg : this is Media Gateway Software R5.1 for E-MGD version 16.7 built on 21 Aug hours 02 min for r_mg_appli_16.7 Downloading /DHS3bin/downbin/emg/binmg from No need to download a new version Checking other files Checking bindspbeconf version Downloading bindspbeconf Downloading /DHS3bin/downbin/emg/bindspbeconf from bindspbeconf successfully downloaded watchdogd now in real time mode Copying bindspbeconf in flash Checking binmgcountry version Downloading binmgcountry Downloading /DHS3bin/downbin/emg/binmgcountry from binmgcountry successfully downloaded Copying binmgcountry in flash ====== record_country_correspondaces ====== record_default_country 0 (DEFAULT COUNTRY : HU based with Poland tones) Downloading /DHS3bin/downbin/emg/binmcv_ver from Downloading dsp binary Downloading /DHS3bin/downbin/emg/binmcv from dsp binary successfully downloaded Copying binmcv in flash loading MCV module - please wait... DSP firmware successfully read in flash (size=657664) Startup completed - awaiting user login... Start VG_PROCESS using /dev/rtf5 Welcome to e-mgd IP is *** Warning: connect to callserver failed! *** *** Please use resolve_connect to get possible cause of failure *** emgd login: TC Ed. 01 /

17 REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 3 A la fin du chargement des binaires e-mgd, le login e-mgd admin user est affiché sur le port de configuration V24. 4 Arrêter la carte GD/GA avec l'interrupteur On/Off et attendre que la LED power passe au rouge fixe. 5 Arrêter l'application OmniPCX Enterprise PC Installer sur le PC Serveur. 6 Dans le cas d'une carte GA, repositionner les dip switchs 1 et 2 sur ON, les dip switchs 3 et 4 sur OFF. Ed. 01 / TC0521

18 OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA TC Ed. 01 /

NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA NAND FLASH D'UNE E-MGD AVEC PC INSTALLER EN RELEASE 5.

NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA NAND FLASH D'UNE E-MGD AVEC PC INSTALLER EN RELEASE 5. COMMUNICATION TECHNIQUE N TC0467 Ed. 02 OmniPCX Enterprise Lx Nb de pages : 17 Date : 19-01-2004 URGENTE NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA Cette communication

More information

Alcatel OmniPCX Enterprise

Alcatel OmniPCX Enterprise Alcatel OmniPCX Enterprise VoIP board IP configuration Maintenance 1 OBJECTIVE: Check the IP configuration of the different VoIP boards VoIP board IP configuration Example with an INTIPA board cplstat

More information

HOST AUTO CONFIGURATION (BOOTP, DHCP)

HOST AUTO CONFIGURATION (BOOTP, DHCP) Announcements HOST AUTO CONFIGURATION (BOOTP, DHCP) I. HW5 online today, due in week! Internet Protocols CSC / ECE 573 Fall, 2005 N. C. State University copyright 2005 Douglas S. Reeves 2 I. Auto configuration

More information

Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.

Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. CHAPTER 5 OBJECTIVES Configure a router with an initial configuration. Use the

More information

Procedure: You can find the problem sheet on Drive D: of the lab PCs. Part 1: Router & Switch

Procedure: You can find the problem sheet on Drive D: of the lab PCs. Part 1: Router & Switch University of Jordan Faculty of Engineering & Technology Computer Engineering Department Computer Networks Laboratory 907528 Lab. 2 Network Devices & Packet Tracer Objectives 1. To become familiar with

More information

VoIP Laboratory B How to re flash an IP04

VoIP Laboratory B How to re flash an IP04 VoIP Laboratory B How to re flash an IP04 (cc) Creative Commons Share Alike Non Commercial Attribution 3 This lab guides you through the process of re flashing an IP04. To re flash a unit is useful when

More information

Voice Gateway with Router

Voice Gateway with Router Voice User Guide Model No. SPA3102 Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates

More information

IP Touch 4088 EE/4018 EE SIP Phone installation manual

IP Touch 4088 EE/4018 EE SIP Phone installation manual IP Touch 4088 EE/4018 EE SIP Phone installation manual 8AL90824AAAAed01 October, 2009 Alcatel-Lucent All Rights Reserved Alcatel-Lucent 2009 1. Overview... 3 2. SIP Stand-Alone Mode... 3 2.1. Initializing

More information

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2 Ethernet Interface Manual Thermal / Label Printer Rev. 1.01 Metapace T-1 Metapace T-2 Metapace L-1 Metapace L-2 Table of contents 1. Interface setting Guiding...3 2. Manual Information...4 3. Interface

More information

CS 326e F2002 Lab 1. Basic Network Setup & Ethereal Time: 2 hrs

CS 326e F2002 Lab 1. Basic Network Setup & Ethereal Time: 2 hrs CS 326e F2002 Lab 1. Basic Network Setup & Ethereal Time: 2 hrs Tasks: 1 (10 min) Verify that TCP/IP is installed on each of the computers 2 (10 min) Connect the computers together via a switch 3 (10 min)

More information

R&S AFQ100A, R&S AFQ100B I/Q Modulation Generator Supplement

R&S AFQ100A, R&S AFQ100B I/Q Modulation Generator Supplement I/Q Modulation Generator Supplement The following description relates to the Operating Manuals, version 03 of R&S AFQ100A, and version 01 of R&S AFQ100B. It encloses the following topics: LXI features,

More information

R&S AFQ100A, R&S AFQ100B I/Q Modulation Generator Supplement

R&S AFQ100A, R&S AFQ100B I/Q Modulation Generator Supplement I/Q Modulation Generator Supplement The following description relates to the Operating Manuals, version 03 of R&S AFQ100A, and version 01 of R&S AFQ100B. It encloses the following topics: LXI features,

More information

AT-S84 Version 1.3.0 (1.0.0.90) Management Software for the AT-9000/24 Gigabit Ethernet Switch Software Release Notes

AT-S84 Version 1.3.0 (1.0.0.90) Management Software for the AT-9000/24 Gigabit Ethernet Switch Software Release Notes AT-S84 Version 1.3.0 (1.0.0.90) Management Software for the AT-9000/24 Gigabit Ethernet Switch Software Release Notes Please read this document before you begin to use the management software. Supported

More information

TFTP Firmware upgrade

TFTP Firmware upgrade Application Note 301 Revision 3, October 2011 This Application Note describes how to upgrade the firmware of your proconx unit using the TFTP method. Prerequisites File transfer utility (Tftpd32.exe, version

More information

BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter

BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter BIT COMMANDER Serial RS232 / RS485 to Ethernet Converter (Part US2000A) Copyrights U.S. Converters 1 Contents Overview and Features... 3 Functions..5 TCP Server Mode... 5 Httpd Client Mode.5 TCP Auto mode....6

More information

Exploring the Remote Access Configuration Utility

Exploring the Remote Access Configuration Utility Exploring the Remote Access Configuration Utility in Ninth-Generation Dell PowerEdge Servers The Remote Access Configuration Utility supports local and remote server management in ninth-generation Dell

More information

A DHCP Primer. Dario Laverde, dario@mediatracker.com. 2002 Dario Laverde

A DHCP Primer. Dario Laverde, dario@mediatracker.com. 2002 Dario Laverde A DHCP Primer Dario Laverde, dario@mediatracker.com 2002 Dario Laverde Dynamic Host Configuration Protocol DHCP Client DHCP DHCP Server Dynamic Host Configuration consists of at least an IP address in

More information

Intel Active Management Technology with System Defense Feature Quick Start Guide

Intel Active Management Technology with System Defense Feature Quick Start Guide Intel Active Management Technology with System Defense Feature Quick Start Guide Introduction...3 Basic Functions... 3 System Requirements... 3 Configuring the Client System...4 Intel Management Engine

More information

IP Power Stone 4000 User Manual

IP Power Stone 4000 User Manual IP Power Stone 4000 User Manual Two Outlet Remote AC Power Controller Multi Link, Inc. 122 Dewey Drive Nicholasville, KY 40356 USA Sales and Tech Support 800.535.4651 FAX 859.885.6619 techsupport@multi

More information

6 Command Line Interface

6 Command Line Interface 6 Command Line Interface The D-Link SmartPro Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol.

More information

Leased Line PPP Connections Between IOS and HP Routers

Leased Line PPP Connections Between IOS and HP Routers Leased Line PPP Connections Between IOS and HP Routers This technical document describes how to connect an IOS Router to an HP Router using point-to-point protocol. An example of an IOS router connected

More information

ACP ThinManager Tech Notes Troubleshooting Guide

ACP ThinManager Tech Notes Troubleshooting Guide ACP ThinManager Tech Notes Troubleshooting Guide Use the F1 button on any page of a ThinManager wizard to launch Help for that page. Visit www.thinmanager.com/technotes/ to download the manual, manual

More information

NOC PS manual. Copyright Maxnet 2009 2015 All rights reserved. Page 1/45 NOC-PS Manuel EN version 1.3

NOC PS manual. Copyright Maxnet 2009 2015 All rights reserved. Page 1/45 NOC-PS Manuel EN version 1.3 NOC PS manual Copyright Maxnet 2009 2015 All rights reserved Page 1/45 Table of contents Installation...3 System requirements...3 Network setup...5 Installation under Vmware Vsphere...8 Installation under

More information

1 Serial RS232 to Ethernet Adapter Installation Guide

1 Serial RS232 to Ethernet Adapter Installation Guide Installation Guide 10/100 Mbps LED (amber color ) Link/Activity LED (green color ) 1. Introduction Thank you for purchasing this 1-port RS232 to Ethernet Adapter (hereinafter referred to as Adapter ).

More information

Management Software. Web Browser User s Guide AT-S106. For the AT-GS950/48 Gigabit Ethernet Smart Switch. Version 1.0.0. 613-001339 Rev.

Management Software. Web Browser User s Guide AT-S106. For the AT-GS950/48 Gigabit Ethernet Smart Switch. Version 1.0.0. 613-001339 Rev. Management Software AT-S106 Web Browser User s Guide For the AT-GS950/48 Gigabit Ethernet Smart Switch Version 1.0.0 613-001339 Rev. A Copyright 2010 Allied Telesis, Inc. All rights reserved. No part of

More information

Dynamic Host Configuration Protocol (DHCP) 02 NAT and DHCP Tópicos Avançados de Redes

Dynamic Host Configuration Protocol (DHCP) 02 NAT and DHCP Tópicos Avançados de Redes Dynamic Host Configuration Protocol (DHCP) 1 1 Dynamic Assignment of IP addresses Dynamic assignment of IP addresses is desirable for several reasons: IP addresses are assigned on-demand Avoid manual IP

More information

3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R-

3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R- MODEL ATC-2004 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2004 is a 4 Port RS232/RS485 to TCP/IP converter integrated with a robust system and network management features

More information

NetBiter webscada Modbus User Manual

NetBiter webscada Modbus User Manual User Manual IntelliCom Innovation AB Pilefeltsgatan 93-95 SE-302 50 Halmstad SWEDEN Phone +46 35 17 29 90 Fax +46 35 17 29 09 email info@intellicom.se www www.intellicom.se Revision List Revision Date

More information

Virtual Appliance for VMware Server. Getting Started Guide. Revision 2.0.2. Warning and Disclaimer

Virtual Appliance for VMware Server. Getting Started Guide. Revision 2.0.2. Warning and Disclaimer Virtual Appliance for VMware Server Getting Started Guide Revision 2.0.2 Warning and Disclaimer This document is designed to provide information about the configuration and installation of the CensorNet

More information

3.1 Connecting to a Router and Basic Configuration

3.1 Connecting to a Router and Basic Configuration 3.1 Connecting to a Router and Basic Configuration Objective This lab will focus on the ability to connect a PC to a router in order to establish a console session and observe the user interface. A console

More information

FRM301 SNMP Upgrade Procedure

FRM301 SNMP Upgrade Procedure The information within this document is intended for experienced service personnel with knowledge of TCP/IP networking, PC networking configuration, serial terminal configuration and operation. Failure

More information

User s Manual TCP/IP TO RS-232/422/485 CONVERTER. 1.1 Introduction. 1.2 Main features. Dynamic DNS

User s Manual TCP/IP TO RS-232/422/485 CONVERTER. 1.1 Introduction. 1.2 Main features. Dynamic DNS MODEL ATC-2000 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2000 is a RS232/RS485 to TCP/IP converter integrated with a robust system and network management features designed

More information

NNAS-D5 Quick Installation Guide

NNAS-D5 Quick Installation Guide NNAS-D5 Quick Installation Guide NOTE: By default, LAN0 (eth0) is set to DHCP. If a DHCP server is available or detected, LAN0 will be assigned a DHCP IP address. If a DHCP server is not available, LAN0

More information

MAX T1/E1. Quick Start Guide. VoIP Gateway. Version 1.0

MAX T1/E1. Quick Start Guide. VoIP Gateway. Version 1.0 MAX T1/E1 TM VoIP Gateway Quick Start Guide Version 1.0 Contents INTRODUCTION 1 Hardware Needed Software Needed 1 1 NET2PHONE MAX SET UP Hardware Set Up Software Set Up Set Up Internet Protocol (IP) Address

More information

Linksys Gateway SPA2100-SU Manual

Linksys Gateway SPA2100-SU Manual Linksys Gateway SPA2100-SU Manual Manuel de l'utilisateur Table of Contents Looking for Basic Setup Instructions?... 3 Most Recent Version of this Manual... 3 Advanced Setup Instructions... 4 Wiring Your

More information

Application Protocols for TCP/IP Administration

Application Protocols for TCP/IP Administration Application Protocols for TCP/IP Administration BootP, TFTP, DHCP Agenda BootP TFTP DHCP BootP, TFTP, DHCP, v4.4 2 Page 60-1 BootP (RFC 951, 1542, 2132) BootP was developed to replace RARP capabilities

More information

Expert Power Control NET 4x 8212 / 8213

Expert Power Control NET 4x 8212 / 8213 2010 Gude Analog- und Digitalsysteme GmbH 2010 Gude Analog- und Digitalsysteme GmbH 23.08.2010 Content 3 Table of content Kapitel 1 Security Advise 5 Kapitel 2 Description 5 Kapitel 3 Hardware 6 3.1 Content

More information

ADDING IP PHONES TO TALKSWITCH

ADDING IP PHONES TO TALKSWITCH TALKSWITCH DOCUMENTATION ADDING IP PHONES TO TALKSWITCH RELEASE 6.50 CT.TS005.008104 ANSWERS WITH INTELLIGENCE COPYRIGHT INFORMATION Copyright 2011 Fortinet, Inc. All rights reserved. Fortinet, FortiGate,

More information

WEB CONFIGURATION. Configuring and monitoring your VIP-101T from web browser. PLANET VIP-101T Web Configuration Guide

WEB CONFIGURATION. Configuring and monitoring your VIP-101T from web browser. PLANET VIP-101T Web Configuration Guide WEB CONFIGURATION Configuring and monitoring your VIP-101T from web browser The VIP-101T integrates a web-based graphical user interface that can cover most configurations and machine status monitoring.

More information

Hands-on MESH Network Exercise Workbook

Hands-on MESH Network Exercise Workbook Hands-on MESH Network Exercise Workbook Santa Clara County RACES Date: 18 March 2015 Version: 1.0 scco_wifi_intro_exonly_v150318.docx 1 Table of Contents HANDS ON! Exercise #1: Looking at your Network

More information

ROM Monitor. Entering the ROM Monitor APPENDIX

ROM Monitor. Entering the ROM Monitor APPENDIX APPENDIX B This appendix describes the Cisco router ROM monitor (also called the bootstrap program). The ROM monitor firmware runs when the router is powered up or reset. The firmware helps to initialize

More information

ACCESS 9340 and 9360 Meter Ethernet Communications Card 9340-60-ETHER

ACCESS 9340 and 9360 Meter Ethernet Communications Card 9340-60-ETHER User s Guide PMCM-ETHCC-0208 2/2008 ACCESS 9340 and 9360 Meter Ethernet Communications Card 9340-60-ETHER TABLE OF CONTENTS INTRODUCTION... 2 Supported Ethernet Protocols... 2 Hardware... 2 Meter Firmware...

More information

GW400 VoIP Gateway. User s Guide

GW400 VoIP Gateway. User s Guide GW400 VoIP Gateway User s Guide P/N: 956YD30001 Copyright 2006. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. i Table of Contents

More information

DOMUSBOX. User guide. Index

DOMUSBOX. User guide. Index DOMUSBOX User guide Index Introduction... 2 1. Installing SEAV DOMUS... 4 1.1 Activating DomusBox... 4 1.2Drawing the environments in DomusWeb... 5 1.3Connecting DomusBox to the devices...9 1.4Configuration

More information

H0/H2/H4 -ECOM100 DHCP & HTML Configuration. H0/H2/H4--ECOM100 DHCP Disabling DHCP and Assigning a Static IP Address Using HTML Configuration

H0/H2/H4 -ECOM100 DHCP & HTML Configuration. H0/H2/H4--ECOM100 DHCP Disabling DHCP and Assigning a Static IP Address Using HTML Configuration H0/H2/H4 -ECOM100 DHCP & HTML 6 H0/H2/H4--ECOM100 DHCP Disabling DHCP and Assigning a Static IP Address Using HTML 6-2 H0/H2/H4 -ECOM100 DHCP DHCP Issues The H0/H2/H4--ECOM100 is configured at the factory

More information

TDP43ME NetPS. Network Printer Server. Control Center. for Ethernet Module

TDP43ME NetPS. Network Printer Server. Control Center. for Ethernet Module Panduit Corp. 2010 TDP43ME NetPS PA26306A01 Rev. 01 11-2010 Network Printer Server Control Center for Ethernet Module NOTE: In the interest of higher quality and value, Panduit products are continually

More information

Cloud.com CloudStack Community Edition 2.1 Beta Installation Guide

Cloud.com CloudStack Community Edition 2.1 Beta Installation Guide Cloud.com CloudStack Community Edition 2.1 Beta Installation Guide July 2010 1 Specifications are subject to change without notice. The Cloud.com logo, Cloud.com, Hypervisor Attached Storage, HAS, Hypervisor

More information

SL 1100 Quick Start Help Guide Table of Contents:

SL 1100 Quick Start Help Guide Table of Contents: SL 1100 Quick Start Help Guide Table of Contents: - 1 - DOCUMENT DESCRIPTION... 3 PERFORMING A COLD START (INITIALIZATION):... 3 INSTALLING THE EXPANSION INTERFACE CARDS:... 3 SL1100 BASE KSU CONNECTIONS:...

More information

Getting started with ARM-Linux

Getting started with ARM-Linux Getting started with ARM-Linux www.embeddedarm.com (480)-837-5200 usa Connecting serial communications and power (JP2 must be installed to enable console) An ANSI terminal or a PC running a terminal emulator

More information

TECHNICAL NOTE. Technical Note P/N 300-999-649 REV 03. EMC NetWorker Simplifying firewall port requirements with NSR tunnel Release 8.

TECHNICAL NOTE. Technical Note P/N 300-999-649 REV 03. EMC NetWorker Simplifying firewall port requirements with NSR tunnel Release 8. TECHNICAL NOTE EMC NetWorker Simplifying firewall port requirements with NSR tunnel Release 8.0 and later Technical Note P/N 300-999-649 REV 03 February 6, 2014 This technical note describes how to configure

More information

Linksys SPA2102 Router Configuration Guide

Linksys SPA2102 Router Configuration Guide Linksys SPA2102 Router Configuration Guide Dear 8x8 Virtual Office Customer, This Linksys guide provides instructions on how to configure the Linksys SPA2102 as a router. You only need to configure your

More information

IP SENSOR 9216 USER MANUAL IP SENSOR 9216 USER MANUAL

IP SENSOR 9216 USER MANUAL IP SENSOR 9216 USER MANUAL IP SENSOR 9216 USER MANUAL USER MANUAL IP SENSOR 9216 Version: 1.0 2006.08-1 - VER. 1.0, Warning: Any changes to this equipment without permission may cause damages to your equipment! This equipment has

More information

Trend Micro Incorporated reserves the right to make changes to this document and to the products described herein without notice.

Trend Micro Incorporated reserves the right to make changes to this document and to the products described herein without notice. Trend Micro Incorporated reserves the right to make changes to this document and to the products described herein without notice. Before installing and using the software, please review the readme files,

More information

Configuring System Message Logging

Configuring System Message Logging CHAPTER 1 This chapter describes how to configure system message logging on the Cisco 4700 Series Application Control Engine (ACE) appliance. Each ACE contains a number of log files that retain records

More information

User Manual. Onsight Management Suite Version 5.1. Another Innovation by Librestream

User Manual. Onsight Management Suite Version 5.1. Another Innovation by Librestream User Manual Onsight Management Suite Version 5.1 Another Innovation by Librestream Doc #: 400075-06 May 2012 Information in this document is subject to change without notice. Reproduction in any manner

More information

Aspen Cloud Server Management Console

Aspen Cloud Server Management Console Aspen Cloud Server Management Console Management of Cloud Server Resources Power All Networks Ltd. User Guide June 2011, version 1.1.1 Refer to ICP V1.1 PAGE 1 Table of Content 1. Introduction... 4 2.

More information

Copyright and Trademarks. How to Use this Guide. Phone Adapter with Router

Copyright and Trademarks. How to Use this Guide. Phone Adapter with Router Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.

More information

Install Guide for JunosV Wireless LAN Controller

Install Guide for JunosV Wireless LAN Controller The next-generation Juniper Networks JunosV Wireless LAN Controller is a virtual controller using a cloud-based architecture with physical access points. The current functionality of a physical controller

More information

CyberData VoIP V2 Speaker with VoIP Clock Kit Configuration Guide for OmniPCX Enterprise

CyberData VoIP V2 Speaker with VoIP Clock Kit Configuration Guide for OmniPCX Enterprise CyberData VoIP V2 Speaker with VoIP Clock Kit Configuration Guide for OmniPCX Enterprise CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 Introduction

More information

Networking Guide Redwood Manager 3.0 August 2013

Networking Guide Redwood Manager 3.0 August 2013 Networking Guide Redwood Manager 3.0 August 2013 Table of Contents 1 Introduction... 3 1.1 IP Addresses... 3 1.1.1 Static vs. DHCP... 3 1.2 Required Ports... 4 2 Adding the Redwood Engine to the Network...

More information

PBX DIGITAL TELEPHONE EXCHANGE MAINTENANCE GUIDE

PBX DIGITAL TELEPHONE EXCHANGE MAINTENANCE GUIDE PBX DIGITAL TELEPHONE EXCHANGE MAINTENANCE GUIDE PBX MAINTENANCE GUIDE MARCH -2010 II Version Table DATE/VERSION OF GUIDE 24.03.2010/AAA DS200L PBX BK REV. AAA 24.03.2010 KAREL reserves the right to make

More information

USER MANUAL GUIMGR Graphical User Interface Manager for FRM301/FRM401 Media Racks

USER MANUAL GUIMGR Graphical User Interface Manager for FRM301/FRM401 Media Racks USER MANUAL GUIMGR Graphical User Interface Manager for FRM301/FRM401 Media Racks CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60 Zhouzi St. Neihu,

More information

Voice Over Internet Protocol (VoIP) Configuration

Voice Over Internet Protocol (VoIP) Configuration (VoIP) Configuration ENGINEERING REPORT No: 02-003 Introduction This report describes interfacing the IPCS VoIP Gateway Model EGW-902 to an ESTeem Model 192E Wireless Ethernet radio modem in a demonstration

More information

CUSTOMER RELEASE NOTES

CUSTOMER RELEASE NOTES RS Switch Router Version 2.0.1.3 January 2002 INTRODUCTION: This document provides specific information for version 2.0.1.3 for the RS Switch Router family of products. It is recommended that one thoroughly

More information

RN-XV-RD2 Evaluation Board

RN-XV-RD2 Evaluation Board RN-XV-RD2 Evaluation Board 2012 Roving Networks. All rights reserved. -1.01Version 1.0 9/28/2012 USER MANUAL OVERVIEW This document describes the hardware and software setup for Roving Networks RN-XV-RD2

More information

29 ThinManager Troubleshooting Guide

29 ThinManager Troubleshooting Guide 29 ThinManager Troubleshooting Guide This is a list of common configuration errors and a guide for fixing them. Note: When any problem arises, check Downloads at www.thinmanager.com for the latest firmware

More information

Reboot the ExtraHop System and Test Hardware with the Rescue USB Flash Drive

Reboot the ExtraHop System and Test Hardware with the Rescue USB Flash Drive Reboot the ExtraHop System and Test Hardware with the Rescue USB Flash Drive This guide explains how to create and use a Rescue USB flash drive to reinstall and recover the ExtraHop system. When booting

More information

Remote PC Guide Series - Volume 2a

Remote PC Guide Series - Volume 2a Document Version: 2013-03-04 This guide provides hardware model-specific guidance in server configuration, with BIOS and RAID configuration instructions for the Dell R710. This guide is part of a multi-volume

More information

ENTERASYS WEBVIEW WEB-BASED MANAGEMENT FOR THE VH-2402S/VH-2402S2 WEB MANAGEMENT GUIDE

ENTERASYS WEBVIEW WEB-BASED MANAGEMENT FOR THE VH-2402S/VH-2402S2 WEB MANAGEMENT GUIDE ENTERASYS WEBVIEW WEB-BASED MANAGEMENT FOR THE VH-2402S/VH-2402S2 WEB MANAGEMENT GUIDE 9033821 Notice NOTICE Enterasys Networks reserves the right to make changes in specifications and other information

More information

Broadband Router ESG-103. User s Guide

Broadband Router ESG-103. User s Guide Broadband Router ESG-103 User s Guide FCC Warning This equipment has been tested and found to comply with the limits for Class A & Class B digital device, pursuant to Part 15 of the FCC rules. These limits

More information

Software Installation Guide

Software Installation Guide Software Installation Guide This manual explains how to install the software over a USB or network connection. Network connection is not available for models SP 200/200S/203S/203SF/204SF. Flowchart The

More information

LifeSize Networker Installation Guide

LifeSize Networker Installation Guide LifeSize Networker Installation Guide November 2008 Copyright Notice 2006-2008 LifeSize Communications Inc, and its licensors. All rights reserved. LifeSize Communications has made every effort to ensure

More information

Information about IP Proprietary Telephones KX-TDA100 KX-TDA200

Information about IP Proprietary Telephones KX-TDA100 KX-TDA200 Model Hybrid IP-PBX Information about IP Proprietary Telephones KX-TDA100 KX-TDA200 Thank you for purchasing a Panasonic Hybrid IP-PBX. Please read this manual carefully before using this product and save

More information

EMS. EtherCAN CI. Ethernet/CAN Interface. User Manual THOMAS WÜNSCHE. Documentation for Ethernet/CAN interface EtherCAN CI version 2.1.

EMS. EtherCAN CI. Ethernet/CAN Interface. User Manual THOMAS WÜNSCHE. Documentation for Ethernet/CAN interface EtherCAN CI version 2.1. Documentation for Ethernet/CAN interface version 2.1. Document version: V3.0 Documentation date: June 16th, 2007 This documentation is not valid for version 2.0 and earlier versions. No part of this document

More information

OSBRiDGE 5XLi. Configuration Manual. Firmware 3.10R

OSBRiDGE 5XLi. Configuration Manual. Firmware 3.10R OSBRiDGE 5XLi Configuration Manual Firmware 3.10R 1. Initial setup and configuration. OSBRiDGE 5XLi devices are configurable via WWW interface. Each device uses following default settings: IP Address:

More information

Troubleshooting Guide

Troubleshooting Guide PYRAMIX 8 Troubleshooting Guide Merging Technologies Le Verney 4, CH-1070 Puidoux Switzerland www.merging.com/horus T : +41 21 946 04 44 F : +41 21 946 04 45 HORUS Make sure that you are running the latest

More information

Ethernet Port Quick Start Manual

Ethernet Port Quick Start Manual Ethernet Port Quick Start Manual THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE ETHERNET PORT OF EDI SIGNAL MONITORS with Ethernet Version 1.5 firmware. DETAILS OF THE ECCOM OPERATION ARE DESCRIBED

More information

Version 0.1 June 2010. Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP)

Version 0.1 June 2010. Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP) Version 0.1 June 2010 Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP) Thank you for choosing the Xerox WorkCentre 7120. Table of Contents Introduction.........................................

More information

Open vswitch Configuration Guide

Open vswitch Configuration Guide Open vswitch Configuration Guide PICA8 Inc. March, 2011 Copyright (C) 2011 Pica8, Inc. All rights reserved. Pica8, Inc. makes no warranty of any kind with regard to this material, including, but not limited

More information

IEEE 802.1Q. Voice VLAN

IEEE 802.1Q. Voice VLAN 1 VLAN (Virtual Local Area Network) is used to logically divide a physical network into several broadcast domains. VLAN membership can be configured through software instead of physically relocating devices

More information

Autonomous NetFlow Probe

Autonomous NetFlow Probe Autonomous Ladislav Lhotka lhotka@cesnet.cz Martin Žádník xzadni00@stud.fit.vutbr.cz TF-CSIRT meeting, September 15, 2005 Outline 1 2 Specification Hardware Firmware Software 3 4 Short-term fixes Test

More information

User Manual Network Interface

User Manual Network Interface User Manual Network Interface Rev. 1.00 SRP-350plusll SRP-352plusll http://www.bixolon.com Table of Contents 1. Manual Information...3 2. Specifications...3 2-1 Hardware version...3 2-2 Configuration Tool...3

More information

F-Secure Internet Gatekeeper Virtual Appliance

F-Secure Internet Gatekeeper Virtual Appliance F-Secure Internet Gatekeeper Virtual Appliance F-Secure Internet Gatekeeper Virtual Appliance TOC 2 Contents Chapter 1: Welcome to F-Secure Internet Gatekeeper Virtual Appliance.3 Chapter 2: Deployment...4

More information

Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above.

Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above. Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A

More information

USER MANUAL. PingBrother EPIW104 managed passive poe switch & IP watchdog

USER MANUAL. PingBrother EPIW104 managed passive poe switch & IP watchdog USER MANUAL PingBrother EPIW104 managed passive poe switch & IP watchdog CONTENT Content... 2 Chapter 1... 3 1.1 Preface... 3 1.2 CE mark warning... 3 1.3 FCC warning... 4 Chapter 2... 5 2.1 Physical description...

More information

! encor en etworks TM

! encor en etworks TM ! encor en etworks TM Version A, March 2010 2013 Encore Networks, Inc. All rights reserved. Configuring the BANDIT III s T1 E1 Card for a PCM Voice Network The T1 E1 card fits into the expansion slot on

More information

ADM5120 HOME GATEWAY CONTROLLER. Product Notes

ADM5120 HOME GATEWAY CONTROLLER. Product Notes HOME GATEWAY CONTROLLER Product Notes ADMtek.com.tw Information in this document is provided in connection with ADMtek products. ADMtek may make changes to specifications and product descriptions at any

More information

1 PC to WX64 direction connection with crossover cable or hub/switch

1 PC to WX64 direction connection with crossover cable or hub/switch 1 PC to WX64 direction connection with crossover cable or hub/switch If a network is not available, or if it is desired to keep the WX64 and PC(s) completely separated from other computers, a simple network

More information

Matrix 510/520 User Guide

Matrix 510/520 User Guide Matrix 510/520 User Guide Introduction: Matrix 510/520 are ARM9-based Linux ready industrial computer. The key features are as follow: Matrix 520 Layout 1. ARM920T ARM Thumb Processor with 200MIPS at 180MHz,

More information

Installation and setup guide V 1.0

Installation and setup guide V 1.0 V o I P G S M G A T E BlueGate SIP 1 Installation and setup guide V 1.0 1. General description 1.1 Technical parametres Dimensions 100 x 130 x 37 mm Weight 850 g Operating position various Operating condition

More information

Connecting the DG-102S VoIP Gateway to your network

Connecting the DG-102S VoIP Gateway to your network Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information

More information

VRC 7900/8900 Avalanche Enabler User s Manual

VRC 7900/8900 Avalanche Enabler User s Manual VRC 7900/8900 Avalanche Enabler User s Manual WLE-VRC-20030702-02 Revised 7/2/03 ii Copyright 2003 by Wavelink Corporation All rights reserved. Wavelink Corporation 6985 South Union Park Avenue, Suite

More information

Introduction to Routing and Packet Forwarding. Routing Protocols and Concepts Chapter 1

Introduction to Routing and Packet Forwarding. Routing Protocols and Concepts Chapter 1 Introduction to Routing and Packet Forwarding Routing Protocols and Concepts Chapter 1 1 1 Objectives Identify a router as a computer with an OS and hardware designed for the routing process. Demonstrate

More information

Backup and Recovery Procedures

Backup and Recovery Procedures CHAPTER 10 This chapter provides Content Distribution Manager database backup and ACNS software recovery procedures. This chapter contains the following sections: Performing Backup and Restore Operations

More information

Reborn Card NET. User s Manual

Reborn Card NET. User s Manual Reborn Card NET User s Manual Table of Contents Notice Before Installation:... 2 System Requirements... 3 1. First Installation... 4 2. Hardware Setup... 4 3. Express Installation... 6 4. How to setup

More information

System Area Manager. Remote Management

System Area Manager. Remote Management System Area Manager Remote Management Remote Management System Area Manager provides remote management functions for its managed systems, including Wake on LAN, Shutdown, Restart, Remote Console and for

More information

Read Me First for the HP ProCurve Routing Switch 9304M and Routing Switch 9308M

Read Me First for the HP ProCurve Routing Switch 9304M and Routing Switch 9308M Read Me First for the HP ProCurve Routing Switch 9304M and Routing Switch 9308M Contents: Software Updates Are Free! New Software Release 05.0.84 Module Installation Getting Started Your Free Ticket to

More information

Lab 5-5 Configuring the Cisco IOS DHCP Server

Lab 5-5 Configuring the Cisco IOS DHCP Server Lab 5-5 Configuring the Cisco IOS DHCP Server Learning Objectives Configure and verify the operation of the Cisco IOS DHCP server Configure an IP Helper address Review the EIGRP configuration Topology

More information

ezvsp User's Manual ( Version 2.1d ) Sollae Systems Co., Ltd.

ezvsp User's Manual ( Version 2.1d ) Sollae Systems Co., Ltd. ezvsp User's Manual ( Version 2.1d ) Sollae Systems Co., Ltd. Contents Chapter 1 Overview 1 1.1 Introduction 1 2.2 Key Features 2 Chapter 2 Installation 3 2.1 Ready to install ezvsp 3 2.2 Install ezvsp

More information

Welcome. Unleash Your Phone

Welcome. Unleash Your Phone User Manual Welcome Unleash Your Phone For assistance with installation or troubleshooting common problems, please refer to this User Manual or Quick Installation Guide. Please visit www.vonage.com/vta

More information