SKILL-BASED EXAM 2 (SET D) BCN/0910I/BCN2083. Name: Date: Instructor: F0/7

Transcription

1 SKILL-BASED EXAM 2 (SET D) BCN/0910I/BCN2083 Name: Date: Instructor: Duration: 1 HOUR and 15 MINUTES Mark: Topology Diagram 100 F0/6 Fa0/0 F0/7 Assessment Objectives Cable a network according to the topology diagram Erase the startup configuration and reload a router and switches to the default state Perform basic configuration tasks on a router and switches Configure and activate interfaces Configure VTP server and clients Configure VLANs on the switches Configure STP Configure inter-vlan routing All contents are Copyright Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 5

2 Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 S1 S2 S3 PC1 PC2 PC3 Fa0/0 Fa0/1 Fa0/1.5 Fa0/1.55 Fa0/1.555 Port and Addressing Assignments This network uses network address / 20. All ip addresses assignment should be subnetted based on this network address and host requirements below. First usable subnet is assigned to the largest host requirements and subsequent subnet used second largest host requirements until the last subnet required. All default gateways and ip-default gateways for switches and routers must use the first available ip address. Switch S2 Ports Assignment Host Requirements F0/1 0/ q Trunks (Native VLAN 555) 4 F0/7 0/10 VLAN 55 Guest (Default) 31 F0/11 0/17 VLAN 5 Faculty/Staff 62 F0/18 0/24 VLAN 15 Students 63 Switch S1 Ports Assignment F0/1 0/ q Trunks (Native VLAN 555) F0/ q Trunks for VLAN Guest, Faculty/Staff and Management only F0/6 Access port for VLAN Students only Switch S3 Ports Assignment F0/1 0/ q Trunks (Native VLAN 555) Page 2 of 5

3 Task 1: Prepare the Network Step 1: Cable a network that is similar to the one in the topology diagram. Step 2: Clear any existing configurations on the devices. Step 3: Disable all ports using the shutdown command. Step 4: Re-enable the active user ports on S2 in access mode. Points : of 5 Task 2: Perform Basic Device Configurations Configure the S1, S2, and S3 switches according to the following guidelines: Configure the hostname. Disable DNS lookup. Configure an EXEC mode enable secret which is class. Configure a password for console connection which is cisco. Configure a password for vty connections which is cisco. Set ip-default gateway. Points : of 6 Task 3: Configure and Activate Network Addresses Step 1: Configure the Management VLAN interface on S1, S2, and S3. Configure S1 with the second available ip address, S2 with third available ip address and S3 with the last available ip address. Step 2: Configure the PC1, PC2, and PC3 Ethernet interfaces. Configure all PCs with the last available ip address. Points : of 9 Page 3 of 5

4 Task 4: Configure VTP Step 1: Configure all trunks. Configure S1, S2 and S3 port trunks for all VLANs. Configure S1 port F0/5 to only allow VLANs that associated with it. Step 2: Configure S1 as the VTP server, with domain name cisco and password cisco. Step 3: Configure S2 and S3 as VTP clients, with domain name and password. Points : of 22 Task 5: Configure VLANs and Associate Switch Port Access VLANs Step 1: Configure the VLANs on the VTP server. Configure the VLANs in the table below on the VTP server. VLAN VLAN Name VLAN 555 Management VLAN 5 Faculty/Staff VLAN 15 Students VLAN 55 Guest Step 2: Verify that the VTP clients are receiving VLAN configurations from the server. Step 3: Configure switch port associated with its VLANs. Points : of 12 Task 6: Configure STP and PortFast Step 1: Configure S1 to be Root Bridge and S3 to be Alternate Root Bridge for Guest and Faculty/Staff VLANs. Configure using spanning-tree vlan vlan-id root command. Step 2: Configure S3 to be Root Bridge and S1 to be Alternate Root Bridge for Students VLAN. Configure using spanning-tree vlan vlan-id priority value command. Use two values and to assign the bridge priority value. All other remaining VLANs will use default priority setting. Page 4 of 5

5 Step 3: Configure PortFast Step 4: Verify that STP is running correctly. Points : of 26 Task 7: Configure Inter-VLAN routing Step 1: Create a basic configuration on the router. Configure the hostname. Disable DNS lookup. Configure an EXEC mode enable secret which is class. Configure a password for console connection which is cisco. Configure a password for vty connections which is cisco. Step 2: Configure the physical interface and subinterface on R1. Fa0/0 on R1 used physical interface (VLAN Students) and Fa0/1 used subinterface (VLAN Guest, Faculty/Staff and Management) for inter-vlans communication. Step 3: Verify Inter-VLAN routing. Ping from each host to every other host. Points : of 20 Task 8: Clean Up NOTE: DO NOT PROCEED WITH CLEANUP UNTIL YOUR INSTRUCTOR HAS GRADED YOUR SKILLS-BASED EXAM AND HAS INFORMED YOU THAT YOU MAY BEGIN CLEANUP. Before turning off power to the switch and router, remove the NVRAM configuration file (if saved) with the privileged exec command erase startup-config. Disconnect and neatly put away all LAN cables that were used in this exam. END OF QUESTION PAPER Page 5 of 5