Guidelines. Note: Aluminum patches are not permitted on Stainless Steel Cladding and visa-versa.

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Guidelines. Note: Aluminum patches are not permitted on Stainless Steel Cladding and visa-versa."

Transcription

1 Refrigerated Containers Structure Panels For interior stainless steel panels depots are required to repair (patch) using stainless steel rivets. Welded patches will be accepted at termination, provided that the Florens general condition of accepting improper repairs is meet. For exterior stainless steel panels, depots are required to repair (patch) using welded patches. Riveted patches will be accepted at termination, provided that Florens general condition of accepting improper repairs is met and the repair is not located on the roof. Roof patches must be welded. Note: Aluminum patches are not permitted on Stainless Steel Cladding and visa-versa. Interior side-wall dents are not to be repaired unless cut. Depots must differentiate when estimating patches that require foaming and those that do not. Bare aluminum or stainless steel patches affixed to pre-painted white aluminum cladding are to be estimated for painting. Patches that are smaller than the minimum required size will be accepted at termination, provided that Florens general condition of accepting improper repairs is met. The patch must be watertight and able to accommodate a minimum of 4 fasteners. (Depots are required to use patches with a minimum dimension of 6 X6 ). The use of steel rivets in aluminum cladding or patches is not permitted. The rivet pattern on patch repairs requires a minimum distance between rivets of 2 (50mm) on center. (Depots are required to conform to the stated IICL criteria of 1 (25mm) on center.) 1

2 Structure Patch not painted Repair is required Example: Bare Aluminum patch affixed to painted white aluminum cladding. Action: Repair required paint the patch white. Aluminum patch with steel fasteners Repair is required Example: Steel fasteners used on aluminum patch. Action: Rectification Required. Replace fasteners and/or patch. 2

3 Structure Example: Proper stainless steel patch welded to stainless steel cladding. Note: Exterior roof patches on the steel cladded units must be welded. Action: No action is required. Sheared rivets Repair on lessee account Example: Sheared rivets resulting from damage. The damage is for lessee account. Action: Rivets should be refastened and sealed. 3

4 Structure Dented but not torn panel Repair is not required Example: Dented interior side wall. Action: No action is required if cut is not present. 4

5 Rails Aluminum Top and Bottom Rail sections that are less than the minimum required by IICL (Must extend at least one meter from the corner casting) criteria may be considered acceptable at termination. To be considered acceptable, the section must end midway between the first and second side post and meet Florens general conditions of accepting improper. (Depot repairs must be in accordance with IICL criteria). Welding of aluminum top and bottom rails is not permitted. The only circumstance where welding may be accepted at termination, is when the weld is located at the splice joint and a proper splice plate has been used. In addition, Florens general condition for accepting improper repairs must be met. (Depot repairs must be in accordance with IICL criteria) Spliced repair with plate Repair is required Example: Welded aluminum top rail splice without splice plates. Action: Rectification is required. Note: At off-hire, welded rail may be acceptable improper repair only when the weld is located at the splice joint and a proper splice plate has been used. In addition, Florens general condition of accepting improper repairs must been met. (Depot repairs must be in accordance with IICL criteria) 5

6 Roof Sheet Flange Example: Damage to roof sheet flange in the area adjacent to the header extension plate. Action: If not cracked or rivets are not missing, no action. Separated roof sheets require no action beyond sealing to prevent water ingress. 6

7 Rails Welded aluminum rail Repair is required Example: Welded aluminum rail. Action: Rectification is required. Example: Damaged aluminum bottom rail below the rivet line. Action: Repair by smoothing and caulking the damaged area. 7

8 Rails Example: Cut aluminum bottom rail upper flange. Action: Damage meets requirement to stopdrill and doubler plate reinforcement. Cleaning Unless directed otherwise by Florens (certain reposition moves), all off-hired reefers require interior steam cleaning. On customer account 8

9 Refrigerated Containers Addendum January 2004 Rails Lower Web and Flange Damage Criteria on Bottom Rail: Cuts, gouges, bends or breakage in the lower web and flange of the bottom rail may be repaired by installing doubler plate over the damaged area. The doubler plate must be installed after first straightening the damaged rail without heat, and then drilling stop holes at both ends of the crack. This repair method may only be used under the following conditions: The area of damage may not extend above the lower edge of the rail by more than 80 mm (3-1/8 in). The area of damage must not exceed 600 mm (24 in) in length. All other provisions shown on the current IICL manual continue to apply. Example: Damaged rail is repaired by doubler plate. Action: No action is required if the damage: Does not extend above the lower edge by more than 80 mm (3-1/8 in) Area does not exceed 600 mm (24 in) in length. Example: The Rail is holed behind T-Clip. Action: No action is required if the above criteria is met. If this type of repair exists at off hire, it is acceptable repair.. 9

10 Miscellaneous Interior drain plugs and chains are not to be replaced. If damaged, Door tie-backs must be replaced. Refurbishment of door frames, sills and headers is only required when the sealing of the door has been compromised. Special approval from Florens is required. If necessary, missing or loose interior sealant is only replaced at the lower panel / rail cove horizontal joint or to correct an improper repair. Missing, damaged or worn kazoos and drain tubes must be repaired / replaced. Hairline cracks at the T- floor threshold are to be corrected only if the structural integrity is compromised Vertical sealant loose No repair is required Example: An example of interior sealant at a vertical joint coming loose. Action: No repair is required. 10

11 Miscellaneous Example: Missing drain tube and kazoo. Action: Replace on lessee account. Missing plug and chain Repair is not required Example: Missing interior drain plug and chains. Action: No action is required. 11

12 Refrigerated Containers Miscellaneous Repairs on corrugated sub-floor Example of a typical Steel floor. Example: Sub-floor cut, torn or cracked (damage not shown) Action: Repair using overlay riveted patches 12

13 Refrigerated Containers Miscellaneous Repairs on corrugated sub-floor. Example: Dent on the sub-floor. Action: Dents do not require repair if not resulting in cut, tear or crack For damages requiring repair of the sub-floor, repair by overlapping a riveted patch. Welded patches are acceptable at off hire. Note: Cut, torn, or cracked sub-floor require repair 13

14 Panel Delamination in Refrigerated Containers (Reefers) Panel delamination on any area of the reefer container is defined as a separation of the insulation core from inner lining of the metal cladding. It can be caused by impact damage or due to defects in the manufacturing process. It is important to distinguish the cause of delamination as this will allow correct allocation to responsible party when rectifying this damage. As a general guide, delamination due to damage results from foam insulation being sheared behind the bond line, leaving residue of the insulation on the cladding which is exposed to premature aging. This damage requires repair. While delamination due to defects, results in the insulation skin being separated from the metal cladding. The insulation skin remains intact, therefore does not cause premature aging. Depending on the location, size of the delaminated area, and the design of the container, delamination bolts should be used. These bolts should be used in a Sandwich Construction where insulated panels contribute a significant portion of panel strength without embedded posts or stringers. Regardless of the cause of delamination, repair is not required on the following areas of the container: Roof Exterior Panel (exterior cladding) Side wall exterior sheet and post design. (sheet riveted to side posts) Sub floor T floor Door exterior Delamination that is not a result of impact damage must be repaired under the following criteria: Exterior Side wall: Over 40% of the total panel area is delaminated. Panel with no posts or panel glued to side posts at 1250 mm centers. Delamination bolts must be used. Interior Side wall: Use delamination bolts in all cases where the delamination is over 40% of the area of the panel. Interior Roof: Repair is required when 30% of the panel area is delaminated. Use rivets when the stringer glued centers are at 1050mm. Interior Door: Repair is required when one area exceeds 50% of the lining area. Use delamination bolts to repair interior door delamination. NOTE: INJECTION OF ADHESIVE FOR DELAMINATION REPAIR IS NOT AL- LOWED. 14

15 Panel Delamination in Refrigerated Containers (Reefers) Installation of Delamination bolt: Delamination Bolt: Cap Nut with Permaglas Rod 100 mm. Cap nut is made of Stainless Steel (SuS). Rod Nut is made of Aluminum. Installation Instructions: 1) Make sure the container is level. Check / match diagonals. 2) Using a template mark the location of the bolt on the interior lining of the container. It is important to install bolts on the recessed area of the corrugation. 3) Using jacks, position the cladding back tightly against the insulation before drilling the holes. 4) After drilling holes, coat each hole using a spray food grade polyurethane clear coating. This coating prevents galvanic reaction, so it is very important. 5) Before installing the bolt, apply caulking underneath the head of the aluminum nut. 6) Install the bolts starting from the center of the panel working out to the ends. Bolt torque is 20ft lbs (0.86m.kgs). 7) Cut of the excess permaglas rod. Affix rivets and seal with Sikaflex 221 or equivalent. Note: Florens requires 5 tight bolts per 4 feet wide panel with one tight bolt in the center of the panel and Note: Side panel bolts are installed from outside to the inside, i.e. the nutsert is installed on the interior lining. 15

16 Panel Delamination in Refrigerated Containers (Reefers) Delamination bolt affixed to the interior recessed area. Example of Delamination bolt on side panel. Delamination should not be repaired for: Roof Exterior Panel (exterior cladding), Side wall exterior sheet and post. (sheet riveted to side posts), Sub floor, T floor, Door exterior. Example of caulk applied underneath the head of the nut and installed rivets. Before installing the delamination bolt, spray with food grade polyurethane to reduce galvanic reaction. 16

17 Panel Delamination in Refrigerated Containers (Reefers) Placement of Tie bolts Florens requires installation of 5 tie bolts for each 4 wide panel. The placement of the tie bolts should be as follows: Secure one bolt directly in the center of the panel Secure two bolts 2 below the top rail with each bolt 1 apart from the left and right edge of the panel. Secure two bolts 2 above the edge of the bottom rail with each bolt 1 apart from the left and right edge of the panel. Placement of tie bolts 17

COMMON INTERCHANGE CRITERIA - "CIC" FOR DRY VAN CONTAINERS

COMMON INTERCHANGE CRITERIA - CIC FOR DRY VAN CONTAINERS COMMON INTERCHANGE CRITERIA - "CIC" FOR DRY VAN CONTAINERS 1st Edition 1 1 st Revision 11 March 2011 RAIL INSPECTION CRITERIA All rails, including side rails, headers and sills Holed, cut, torn or cracked;

More information

TRITON CONTAINER INTERNATIONAL. Reefer Technical Bulletins. Version 4.0

TRITON CONTAINER INTERNATIONAL. Reefer Technical Bulletins. Version 4.0 TRITON CONTAINER INTERNATIONAL Version 4.0 February 2013 Table Of Contents (Hold Ctrl button and click on any item below to go directly to that section of the manual.) 1 INTRODUCTION... 3 2 REFRIGERATED

More information

INSTALLATION OF A BAY WINDOW

INSTALLATION OF A BAY WINDOW INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening

More information

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel

More information

Chapter. Restoration of Damaged Structures

Chapter. Restoration of Damaged Structures 5 Chapter Restoration of Damaged Structures Bringing back a damaged structure to its pre-earthquake state and original strength is called restoration. This is the first step of building rehabilitation.

More information

How to secure your property after a disaster

How to secure your property after a disaster How to secure your property after a disaster The Red Guide to Recovery HOuse secured properly Board-Up of Windows, Doors and Roof Hole. Lot secured with Perimeter Fencing. Fires, floods, tornadoes, hurricanes,

More information

1.02 MATERIAL: A. Metal: Prime furniture steel, free of scales, buckles, or other defects; ASTM A366.

1.02 MATERIAL: A. Metal: Prime furniture steel, free of scales, buckles, or other defects; ASTM A366. 1.01 GENERAL: A. Fume hoods shall be of a "picture frame" airfoil design and construction. Each fume hood superstructure shall provide for safe efficient removal of all fumes, both heavy and light, with

More information

Sundance Supply, LLC. Greca Corrugated Polycarbonate Design & Install. To order Polycarbonate see >

Sundance Supply, LLC. Greca Corrugated Polycarbonate Design & Install. To order Polycarbonate see > Sundance Supply, LLC Greca Corrugated Polycarbonate Design & Install To order Polycarbonate see > http://www.sundancesupply.com Corrugated polycarbonate is sold in 1 ft. Increments. (1) (2) 30ʼ x 48ʼ Greenhouse

More information

The City of Winnipeg Section Turtle Island Community Centre Renovation Page 1 of 5

The City of Winnipeg Section Turtle Island Community Centre Renovation Page 1 of 5 Turtle Island Community Centre Renovation Page 1 of 5 Part 1 General 1.1 SECTION INCLUDES.1 Shop fabricated ferrous metal items..2 Shop fabricated aluminum items..3 Steel pipe handrails balusters, and

More information

SLIDING DOORS. 3. For doors fitted to the eave side of the building this header takes the form of an additional eave purlin.

SLIDING DOORS. 3. For doors fitted to the eave side of the building this header takes the form of an additional eave purlin. 1 SLIDING DOORS AGS/DR/03 The aim of this instruction is to guide you through the process of construction and fitting of Sliding Doors. Due to the number of sizes available this instruction is written

More information

NEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS FIBRE CEMENT CLADDING

NEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS FIBRE CEMENT CLADDING NEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS Reference Guide 0.1 GENERAL 0.1 Reference Guide 0.2 Index 0.3 Disclaimer & Limitations 0.4 General Notes

More information

LOCK BOLT ADJUSTMENT SCREW EXTERIOR SIDE DOOR FRAME WIDTH ROUGH FRAMED OPENING ROUGH OPENING. (Figure 1)

LOCK BOLT ADJUSTMENT SCREW EXTERIOR SIDE DOOR FRAME WIDTH ROUGH FRAMED OPENING ROUGH OPENING. (Figure 1) 160 SERIES OUT SWING ALUMINUM SINGLE OR PAIR DOOR WITH OR WITHOUT SIDELITE(S) INSTALLATION INSTRUCTIONS READ INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING THE INSTALLATION These instructions are provided as

More information

INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin (JII006)

INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin (JII006) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl Patio Doors with nailing fin. Any local building code requirements supersede the recommended

More information

Quaker Windows & Doors Folding Patio Door Installation Instructions

Quaker Windows & Doors Folding Patio Door Installation Instructions Quaker Windows & Doors Folding Patio Door Installation Instructions 2/15 Installer Read instructions completely before attempting installation. Failure to follow these guidelines will forfeit all warranties

More information

CONSTRUCTION STAGES STAGE 1: PRELIMINARY WORK, AUXILIARY MATERIALS, TOOLS

CONSTRUCTION STAGES STAGE 1: PRELIMINARY WORK, AUXILIARY MATERIALS, TOOLS CONSTRUCTION STAGES STAGE 1: PRELIMINARY WORK, AUXILIARY MATERIALS, TOOLS - TOOLS AUXILIARY MATERIALS FOR INSTALLATION OF MOLDS CONSTRUCTION OF FOUNDATIONS PREPARATION OF THE CONSTRUCTION SITE MARKING

More information

Piper Aircraft Corporation 2926 Piper Drive Vero Beach, Florida, U.S.A

Piper Aircraft Corporation 2926 Piper Drive Vero Beach, Florida, U.S.A 977 Piper Aircraft Corporation 2926 Piper Drive Vero Beach, Florida, U.S.A. 32960 DATE: December 12, 1994 (S/M) SUBJECT: MODELS AFFECTED: Inspection of Wing Rear Attach Fitting and Addition of Inspection

More information

7. Installation. installation 7.1.1. CAST-IN WINDOW SYSTEM 7.1. INSTALLATION OF WINDOW MAIN FRAME

7. Installation. installation 7.1.1. CAST-IN WINDOW SYSTEM 7.1. INSTALLATION OF WINDOW MAIN FRAME 7. Installation Window involves the fixing of window frame at an earlier construction stage and subsequent of the window sashes. This is a highly workmanship dependent process. Only trained and approved

More information

SECTION METAL STAIRS, LADDERS, AND WALKWAYS

SECTION METAL STAIRS, LADDERS, AND WALKWAYS SECTION 05510 METAL STAIRS, LADDERS, AND WALKWAYS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Technical requirements for metal stairs, ladder, and walkways. 1.2 REFERENCES A. General: References to

More information

INSTALLATION INSTRUCTIONS CLAD INSWING BI-FOLD DOOR AND WINDOW SYSTEM WITH U-CHANNEL

INSTALLATION INSTRUCTIONS CLAD INSWING BI-FOLD DOOR AND WINDOW SYSTEM WITH U-CHANNEL INSTALLATION INSTRUCTIONS CLAD INSWING BI-FOLD DOOR AND WINDOW SYSTEM WITH U-CHANNEL Please read these instructions in their entirety prior to beginning the installation process. Sierra Pacific Windows

More information

The Manitoba Water Services Board SECTION 027110 Standard Construction Specifications September 2013 Page 1 of 12

The Manitoba Water Services Board SECTION 027110 Standard Construction Specifications September 2013 Page 1 of 12 September 2013 Page 1 of 12 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work shall consist of the supply and construction of a chain link fence, barb wire fences or mesh fences as shown on the Plans or

More information

TABLE OF CONTENTS ..12

TABLE OF CONTENTS ..12 TABLE OF CONTENTS INSTALLATION MANUAL ENERGY WALL TM IS 4000 7.1 CONTINUOUS EXTERIOR INSULATION PANEL SYSTEM FOR USE IN NEW CONSTRUCTION I. Instructions for Wall Installations: STEP 1 STEP 2 STEP 3.2 IS

More information

3000R REEFER SERIES THE WORLD S LEADING PRODUCER OF QUALITY, LIGHT WEIGHT TRAILERS.

3000R REEFER SERIES THE WORLD S LEADING PRODUCER OF QUALITY, LIGHT WEIGHT TRAILERS. 3000R REEFER SERIES THE WORLD S LEADING PRODUCER OF QUALITY, LIGHT WEIGHT TRAILERS. KEEPING DELIVERIES COLD AND SAFE FOR GENERATIONS When brothers E.W. and H.C. Bennett founded Utility Trailer Manufacturing

More information

INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001)

INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions

More information

Generic Technical Performance Specification GTS-1653 February 2001 Issue: 01 Revision: 00 Page 1 of 5

Generic Technical Performance Specification GTS-1653 February 2001 Issue: 01 Revision: 00 Page 1 of 5 Issue: 01 Revision: 00 Page 1 of 5 1 ASSEMBLY - GENERAL 1.1 The work of this section includes the provision of all design, labour, materials, equipment and services required to fabricate and install stair

More information

GreenGuard Housewrap Installation Guide

GreenGuard Housewrap Installation Guide 000768PACBPHW_Flashing Bro 5/23/03 2:52 PM Page 1 For the most current product information, go to www.green-guard.com. Pactiv Building Products believes the information and recommendations herein to be

More information

Fig. 2 WALL-TO-WALL PANEL CONNECTIONS CORNER WALL CONNECTION

Fig. 2 WALL-TO-WALL PANEL CONNECTIONS CORNER WALL CONNECTION SIPS SCREWS WITH MINIMUM 1" PENETRATION IN WOOD MEMBER IN SIP WALL PANEL CONNECTED TO @ 24" O.C. MAXIMUM OUTSIDE SKIN EACH SIDE OF FRAMING TYP. AS RECOMMENDED BY FOAM CORE AS EACH SIDE OF FRAMING TYP.

More information

Window Installation Instructions

Window Installation Instructions Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for

More information

EAST LYME HIGH SCHOOL

EAST LYME HIGH SCHOOL Overview: 1971 N 1966 GYM 1966 CLASSROOM WING 1966 AUD. 1971 GYM 1998 1998 POOL EAST LYME HIGH SCHOOL Original 1966 Building: The original East Lyme High School was constructed in 1966 and was composed

More information

March 14, 2007. Installation of Bay, Bow and Garden Windows

March 14, 2007. Installation of Bay, Bow and Garden Windows March 14, 2007 Re: Installation of Bay, Bow and Garden Windows Attached are the Atrium Companies, Inc recommendation for the installation of bay, bow and garden windows. These instructions were developed

More information

PART 1 GENERAL 1.1 SECTION INCLUDES

PART 1 GENERAL 1.1 SECTION INCLUDES J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including

More information

EXSULATION S5000 Mineral Wool Slab Non Combustible EIFS DSC5001. Exsulation S5000 System Installation Details DRYVIT SYSTEMS CANADA

EXSULATION S5000 Mineral Wool Slab Non Combustible EIFS DSC5001. Exsulation S5000 System Installation Details DRYVIT SYSTEMS CANADA EXSULATION S5000 Mineral Wool Slab Non Combustible EIFS DSC5001 Exsulation S5000 System Installation Details Exsulation S5000 DETAIL Table of Contents NOTE EXS.0.0.01 EXS.0.0.02A EXS.0.0.02B EXS.0.0.03

More information

TABLE OF CONTENTS-REPAIR / DAMAGE

TABLE OF CONTENTS-REPAIR / DAMAGE AXLE BEAM TABLE OF CONTENTS-REPAIR / DAMAGE BOTTOM RAIL COMBINATION FRONT, Refrigeration Unit Opening CORNER POST CROSSMEMBER, Intermediate CROSSMEMBER, Over Landing Gear CROSSMEMBER, Over Suspension CROSSMEMBER,

More information

TOLL FREE NUMBER:

TOLL FREE NUMBER: Page 2 Page Aluminum Floor Access Doors: Angle Frames: (cast into concrete) APS150 & APS300: Single Door, Pedestrian Loading...4 APD150 & APD300: Double Door, Pedestrian Loading...6 APS150 & APS300 with

More information

5. Front Lower Rail Assembly

5. Front Lower Rail Assembly 5. Front Lower Rail Assembly Lower Rail Sub-Assembly The lower rail service part comes as a sub-assembly, which consists of seven brackets and panels. Instuction sheets and templates are also included.

More information

SECTION 32 31 13 CHAIN LINK FENCES AND GATES

SECTION 32 31 13 CHAIN LINK FENCES AND GATES SECTION 32 31 13 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Fence framework, fabric, and accessories. 2. Excavation for post bases. 3. Concrete foundation for posts

More information

SAMPLE TEST QUESTIONS INSULATOR - ITA WEBSITE

SAMPLE TEST QUESTIONS INSULATOR - ITA WEBSITE 1 Fibreglass vapour seal insulation is available in sheets 24 in. 48 in. 2 in., with 5 sheets per bundle. How many bundles of insulation are required to cover an area 80 ft. long by 22 ft. wide? A. 19

More information

Installation Instructions

Installation Instructions Please read all instructions before installing wall panels. Always plan before you place! 1. Before installation: a. Acclimate Stain Steel Panels, Trim, adhesives and wall substrates to room temperature

More information

SECTION 02630 STORM DRAINAGE SYSTEM

SECTION 02630 STORM DRAINAGE SYSTEM SECTION 02630 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for storm drainage systems including modifications and connections to existing storm drainage systems. 1.02 REFERENCE

More information

Clad Direct Glaze Window Installation Instructions

Clad Direct Glaze Window Installation Instructions Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully

More information

ZODIAC 601 XL. Remove the baggage floor to install the flap controls.

ZODIAC 601 XL. Remove the baggage floor to install the flap controls. Remove the baggage floor to install the flap controls. NOTE: The control tube can also be installed by access through the bottom fuselage access door 6B3-8 Rear view. Electric flap actuator bolted behind

More information

Support Joining Guide

Support Joining Guide Guide Guide for Andersen Casement, Awning, and Picture Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential

More information

SEE JAMB 3/4" 1 1/2" 14 NOTES: 1. SEE DETAIL 1 FOR KEYNOTE MATERIAL DESCRIPTIONS

SEE JAMB 3/4 1 1/2 14 NOTES: 1. SEE DETAIL 1 FOR KEYNOTE MATERIAL DESCRIPTIONS . FACE OF WALL.. STUD CONSTRUCTION WITH FIBERGLASS BATT INSULATION AND FIBERGLASS FACED EXTERIOR GYPSUM SHEATHING WITH JOINTS SEALED USING -PART POLYURETHANE PRIOR TO INSTALLING FLUID APPLIED WEATHER RESISTANT

More information

-1- SPECIFICATIONS 002085 CONE SETTER PLATFORM ATTACHMENT INDEX

-1- SPECIFICATIONS 002085 CONE SETTER PLATFORM ATTACHMENT INDEX -1-002085 CONE SETTER PLATFORM ATTACHMENT INDEX I. GENERAL EQUIPMENT : A. Intent Statement B. Cone Setter Platform II. III. 1. Understructure Frame 2. Mounting Components 3. Paint 4. Basket 5. Labels 6.

More information

Alenia Experiences on Composite Structures Repairs Benedetto Gambino

Alenia Experiences on Composite Structures Repairs Benedetto Gambino Alenia Experiences on Composite Structures Repairs Benedetto Gambino Amsterdam, 10 May 2007 ALENIA OVERVIEW CFRP roadmap - Wing mouv. Parts -Empennage mouv. parts (H/C sandwich and full depth) -Vertical

More information

GOOD ROOFING PRACTICE STEEP-SLOPE RE-ROOFING ASPHALT SHINGLE ROOFING 1:3 (4/12) AND GREATER

GOOD ROOFING PRACTICE STEEP-SLOPE RE-ROOFING ASPHALT SHINGLE ROOFING 1:3 (4/12) AND GREATER GOOD ROOFING PRACTICE STEEP-SLOPE RE-ROOFING ASPHALT SHINGLE ROOFING 1:3 (4/12) AND GREATER 1 DECK Revised January 6, 2011 1.1 General a) Application of asphalt shingles directly over rigid insulations

More information

Introduction. Required Materials

Introduction. Required Materials C e r t a i n Te e d Air Barrier Installation Instructions for Wood Framing Introduction In addition to performing as an interior vapor retarder, MemBrain may be installed as a continuous, interior air

More information

1036 Parkway Ct. Phone: 770-932-0202 Buford, GA 30518 Fax: 770-945-0041

1036 Parkway Ct. Phone: 770-932-0202 Buford, GA 30518 Fax: 770-945-0041 CONSTRUCTION 1. A. GENERAL 1.A.1. The intent of this specification is to set forth construction and design standards that will result in an installation of modular cabinetry requiring FLUSH OVERLAY CONSTRUCTION.

More information

Excerpts from the Canadian National Building Code (NBC)

Excerpts from the Canadian National Building Code (NBC) Excerpts from the Canadian National Building Code (NBC) Reproduced here with Permission of the Copyright Owner, the National Research Council of Canada, Institute for Research in Construction. For more

More information

PANELIZED HOME INSTALLATION GUIDELINE

PANELIZED HOME INSTALLATION GUIDELINE PANELIZED HOME INSTALLATION GUIDELINE A typical home package will be constructed of Snap-N-Lock Insulated Panels clad with steel skins. 4" panels will be used for the walls, and 6" panels for the roof.

More information

SECTION 6. Glass Storefront Doors:

SECTION 6. Glass Storefront Doors: SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail

More information

GUIDELINES FOR INSTALLATION OF AIR CONDITIONING UNITS 174-180 PHILLIP STREET, SYDNEY

GUIDELINES FOR INSTALLATION OF AIR CONDITIONING UNITS 174-180 PHILLIP STREET, SYDNEY GUIDELINES FOR INSTALLATION OF AIR CONDITIONING UNITS 174-180 PHILLIP STREET, SYDNEY July 2008 1.0 SCOPE These guidelines describe the way in which air conditioning units shall be installed or replaced

More information

Foundation Experts, LLC Specializes in Foundation Repair and Waterproofing

Foundation Experts, LLC Specializes in Foundation Repair and Waterproofing 1 Most basements show some signs of leaking and cracking. Through the years, problems with water, poor soils, grading, drainage and possible settling affect the integrity of a basement. Being able to recognize

More information

SECTION 02832 CHAIN LINK FENCE AND GATES

SECTION 02832 CHAIN LINK FENCE AND GATES SECTION 02832 CHAIN LINK FENCE AND GATES PART 1 GENERAL 1.01 SECTION INCLUDES A. Fabrication, furnishing and installation of chain link fence, chain link gates, and extension brackets with barbed wire.

More information

Superform Products Ltd.

Superform Products Ltd. TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000

More information

SECTION CHAIN LINK FENCE AND GATES

SECTION CHAIN LINK FENCE AND GATES SECTION 02830 CHAIN LINK FENCE AND GATES PART 1 GENERAL 1.01 SCOPE OF WORK The work covered in this section shall include all materials, labor, and equipment necessary for a complete installation of the

More information

LLOYD INDUSTRIES INC. DAMPER INSTALLATION INSTRUCTIONS

LLOYD INDUSTRIES INC.  DAMPER INSTALLATION INSTRUCTIONS DAMPER Installation and Maintenance Instructions 1-1/2 Hour Rated, UL Classified model 75 fire dampers For use in fire barriers with ratings of less than 3 hours INSPECTION 1. Inspect for shipping damage.

More information

SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT

SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Equipment

More information

Specifications. Preformed Metal Wall and Roof Panels. Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023

Specifications. Preformed Metal Wall and Roof Panels. Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023 Specifications Preformed Metal Wall and Roof Panels Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023 Section 07410 Preformed Metal Wall and Roof Panels Structural

More information

The better way to build TM. Installation Manual. FOUNDATION SIPs & FROST WALLS SIPs

The better way to build TM. Installation Manual. FOUNDATION SIPs & FROST WALLS SIPs The better way to build TM Installation Manual FOUNDATION SIPs & FROST WALLS SIPs February 2016 PWF FOUNDATION & FROST WALL SIPs Installation Manual Table of Contents Topics General Requirements...................................

More information

HELP INSTALLING A PRODUCT

HELP INSTALLING A PRODUCT HELP INSTALLING A PRODUCT HEALTH AND SAFTY A method statement and site-specific risk assessment should be produced to ensure a safe system of work exists before commencing installation to comply with current

More information

Tools required by installer: Materials required by installer:

Tools required by installer: Materials required by installer: Installation Guidelines For Quaker Window Products Vinyl replacement product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions

More information

Polaris Slingshot Trailer Hitch Installation Instructions #PSS007

Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 1. Lay out and familiarize yourself with the components and hardware supplied with the hitch. Note the included trailer wiring isolator

More information

HfHMD uses LP SmartSide siding and trim.

HfHMD uses LP SmartSide siding and trim. HfHMD uses LP SmartSide siding and trim. These products are: More durable than cement fiber board. Much more volunteer-friendly to install. When installed correctly, have a 5/50- year pro-rated warranty.

More information

Page 1 of 5

Page 1 of 5 SPECIFICATIONS METAL COMPOSITE MATERIAL WALL PANELS ESTOLGA 3000 DRY SEAL SYSTEM PART 1 GENERAL 1.01 SECTION INCLUDES A. Exterior cladding consisting of formed metal composite material (MCM) sheet, secondary

More information

Flat Pan Patio Cover With Trim Kit-Basic Installation Guidelines

Flat Pan Patio Cover With Trim Kit-Basic Installation Guidelines Flat Pan Patio Cover With Trim Kit-Basic Installation Guidelines Recommended Tools: Safety Glasses Work Gloves Wide Pencil Min 30 Steel Tape measure Carpenters Framing Square Chalk Line Stud Finder Hammer

More information

Front door. Volkswagen Golf V - Front door. Special tools, testers and auxiliary items required. Socket wrench T Assembly tool T 10118

Front door. Volkswagen Golf V - Front door. Special tools, testers and auxiliary items required. Socket wrench T Assembly tool T 10118 Volkswagen Golf V - Front door Page 1 / 44 57-1 Front door Tools Special tools, testers and auxiliary items required Socket wrench T 10072 Assembly tool T 10118 Door adjusting wrench 3320 Joint for 3320

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised December 2, 2012 the Aspen 10' x 8' or 12' x 8' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is

More information

Calvert USA, Inc. Attic Stairs

Calvert USA, Inc. Attic Stairs Calvert USA, Inc. Attic Stairs Instructions for installation of vertical opening access stairs Model numbers: 7035 through 7047 Calvert USA, Inc., P.O. Box 841, Solomons, MD 20688, Tel. (410) 286-1430,

More information

September 1, 2003 CONCRETE MANUAL 5-694.900 CONCRETE PAVEMENT REHABILITATION 5-694.900

September 1, 2003 CONCRETE MANUAL 5-694.900 CONCRETE PAVEMENT REHABILITATION 5-694.900 September 1, 2003 CONCRETE MANUAL 5-694.900 5-694.901 GENERAL CONCRETE PAVEMENT REHABILITATION 5-694.900 Concrete Pavement Rehabilitation is an extremely valuable tool of the Minnesota Department of Transportation

More information

Fire- and soundproof door EI30/Rw40dB installation guide

Fire- and soundproof door EI30/Rw40dB installation guide HAAPSALU UKSETEHASE AS 19.15.2015 version 1 Masti tee 8, 90401 Uuemõisa, Ridala vald, Lääne maakond, Estonia tel: +372 47 20 800, fax: +372 47 20 803, www.uksetehas.ee, info@uksetehas.ee Fire- and soundproof

More information

Chocks, Chocking and CHOCKFAST. - Marine Chock Installation - Presented by. ITW Philadelphia Resins

Chocks, Chocking and CHOCKFAST. - Marine Chock Installation - Presented by. ITW Philadelphia Resins Chocks, Chocking and CHOCKFAST - Marine Chock Installation - Presented by ITW Philadelphia Resins Presentation Outline Basic Chocking Procedure Special Chocking Situations Some Chocking Do s & Don ts For

More information

SECTION REINFORCING STEEL. 1. Section , Structural Concrete.

SECTION REINFORCING STEEL. 1. Section , Structural Concrete. SECTION 03 21 00 REINFORCING STEEL PART 1 GENERAL 1.01 SECTION INCLUDES A. This WORK shall consist of furnishing and placing reinforcing steel in accordance with these SPECIFICATIONS and in conformity

More information

SAMPLE TEST QUESTIONS GLAZER - ITA WEBSITE

SAMPLE TEST QUESTIONS GLAZER - ITA WEBSITE 1 Small amounts of hazardous chemicals used on several shifts are to be transferred from one container to another. How should the new container be labeled? A. Mark new container with product name only.

More information

SECTION METAL BUILDING SYSTEMS. A. Metal wall and roof panels including gutters and downspouts.

SECTION METAL BUILDING SYSTEMS. A. Metal wall and roof panels including gutters and downspouts. New Football Stadium 13.34.19-1 PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 13.34.19 METAL BUILDING SYSTEMS A. Metal wall and roof panels including gutters and downspouts. 1.02 RELATED REQUIREMENTS A.

More information

Continuous Dow Corning 791 Silicone Weatherproofing Sealant cap along edge of silicone transition strip. Dow Corning Silicone Transition System (STS)

Continuous Dow Corning 791 Silicone Weatherproofing Sealant cap along edge of silicone transition strip. Dow Corning Silicone Transition System (STS) : Drawing Details Details cap along edge of silicone transition strip Silicone Transition System (STS) Fillet bead of at top of flashing lapped on to flashing, over STS and onto field layer layers staggered

More information

WINDOW INSTALLATION GUIDE

WINDOW INSTALLATION GUIDE WINDOW INSTALLATION GUIDE is not responsible for or liable for any use or misuse of the information contained in this window installation guide. Window Installation Guide This guide provides basic information

More information

Sliding Patio Door Milgard Aluminum Door

Sliding Patio Door Milgard Aluminum Door Sliding Door Sliding Patio Door Milgard Aluminum Door The Series Sliding Door has been specially designed to meet the building practices and climatic conditions of the West Coast market. The door features

More information

Sun Windows General Information Sun New Construction Window Installation Instructions

Sun Windows General Information Sun New Construction Window Installation Instructions Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten

More information

Installation Instructions

Installation Instructions Installation Instructions For Use with PXPV230, PXPV265, PXPD230, and PXPD265 models Attention! - Please read these instructions completely before attempting installation. Always unplug the power supply

More information

XYZ Corporation. Project Waterproofing Handbook. 23 June 2008. Working Set Rev. 0. Project Address: 8888 Main Street York, PA 88888

XYZ Corporation. Project Waterproofing Handbook. 23 June 2008. Working Set Rev. 0. Project Address: 8888 Main Street York, PA 88888 Arch itectu ral Te sting Inc. XYZ Corporation 23 June 2008 Project Waterproofing Handbook Working Set Rev. 0 Project Address: 8888 Main Street York, PA 88888 Prepared By: Architectural Testing 4 Rancho

More information

Specifications for Walk-In Coolers & Freezers Leer, Inc.

Specifications for Walk-In Coolers & Freezers Leer, Inc. Specifications for Walk-In Coolers & Freezers Leer, Inc. 1.0 General 1.1 Walk-In coolers and freezers provided under this section of the specifications shall be prefabricated of modular design and construction.

More information

NO-WELD PANEL REPAIR KIT

NO-WELD PANEL REPAIR KIT NO-WELD PANEL REPAIR KIT INSTRUCTIONS Item #31102 Caulk gun not included The EASTWOOD NO-WELD PANEL REPAIR KIT is designed to make permanent patch panel repairs in steel and aluminum when a welder is not

More information

1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings.

1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings. SECTION 32 31 13 CHAIN LINK FENCES PART 1 GENERAL 1.1 SUMMARY A. This Section includes: 1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings.

More information

Mark Cramer Inspection Services, Inc.

Mark Cramer Inspection Services, Inc. Mark Cramer Inspection Services, Inc. 492 Twentieth Avenue, Indian Rocks Beach, FL 34635-2970 (727) 595-4211 Fax (727) 596-7583 Certified Member #12085 American Society of Home Inspectors Construction

More information

RESIDENTIAL MASONRY A BEST PRACTICES GUIDE

RESIDENTIAL MASONRY A BEST PRACTICES GUIDE RESIDENTIAL MASONRY A BEST PRACTICES GUIDE Build With Brick Build With Boral CONTENTS BRICK :01 MASONRY CEMENT :03 MASONRY SAND :04 WALL TIES :05 STEEL LINTELS :07 DRAINAGE WALL SYSTEM :09 FLASHING :11

More information

Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows

Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read

More information

Florida Building Code, 5 th Edition SHINGLE ROOFING

Florida Building Code, 5 th Edition SHINGLE ROOFING Florida Building Code, 5 th Edition SHINGLE ROOFING Date Issued/Updated: July 6, 2015 This bulletin addresses the current Building Code roofing and re roofing requirements for shingle roofing systems.

More information

SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS

SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS 1 SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and

More information

CITY OF WHITE BEAR LAKE BUILDING INSPECTION DEPARTMENT 4701 Highway 61 White Bear Lake, MN 55110 Fax: 651-429-8503. Re-Roofing: Asphalt Shingles

CITY OF WHITE BEAR LAKE BUILDING INSPECTION DEPARTMENT 4701 Highway 61 White Bear Lake, MN 55110 Fax: 651-429-8503. Re-Roofing: Asphalt Shingles CITY OF WHITE BEAR LAKE BUILDING INSPECTION DEPARTMENT 4701 Highway 61 White Bear Lake, MN 55110 Fax: 651-429-8503 Re-Roofing: Asphalt Shingles This is a summary of the standard requirements based on the

More information

The WANZ Guide to Window Installation

The WANZ Guide to Window Installation The WANZ Guide to Window Installation as described in E2/AS1 Amendment 5 Ver. 1.1 Page 2 of 74 Contents Overview Page 5 Objective Page 5 Scope Page 5 Opening Preparation Page 7 Step P1 Preliminary Check

More information

Mounting guide for a masonry/concrete wall with exterior insulation to achieve ASHRAE 90.1 continuous insulation barrier.

Mounting guide for a masonry/concrete wall with exterior insulation to achieve ASHRAE 90.1 continuous insulation barrier. Mounting guide for a masonry/concrete wall with exterior insulation to achieve ASHRAE 90.1 continuous insulation barrier. Summary The R-TEC CI System for affixing fassade cladding to a masonry/concrete

More information

TECHNICAL MANUAL PIPECLAMP JULY 2013 ROHRVERBINDER ONLINESHOP.DE

TECHNICAL MANUAL PIPECLAMP JULY 2013 ROHRVERBINDER ONLINESHOP.DE TECHNICAL MANUAL PIPECLAMP JULY 2013 ROHRVERBINDER ONLINESHOP.DE Selecting a Fitting fittings are a blackheart malleable casting and are manufactured to BS EN 1562 1997 for the strength requirements. fittings

More information

SECTION STANDING SEAM METAL ROOFING

SECTION STANDING SEAM METAL ROOFING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 07 41 13 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Use for roofing sloped 1 in 4 (3 in/ft) or greater. 3. Delete between // // if not applicable

More information

POST AND FRAME STRUCTURES (Pole Barns)

POST AND FRAME STRUCTURES (Pole Barns) POST AND FRAME STRUCTURES (Pole Barns) Post and frame structures. The following requirements serve as minimum standards for post and frame structures within all of the following structural limitations:

More information

Tundra Series Windows January 2016

Tundra Series Windows January 2016 Tundra Series Windows January 2016 New Construction Installation Instructions Nail Fin, J-Fin and Brickmold Aplications product. ATTENTION! Read and understand all installation instructions before installing

More information

before tightening the bolts. This will help eliminate the potential for any interference between the flywheel housing and the oil pan.

before tightening the bolts. This will help eliminate the potential for any interference between the flywheel housing and the oil pan. SERIES 60 SERVICE MANUAL before tightening the bolts. This will help eliminate the potential for any interference between the flywheel housing and the oil pan. 1. Drain Plug 6. Bolt 2. Nut 7. Plug 3. Isolator

More information

TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE

TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE TECHNICAL SPECIFICATION PART 8000 - PRECAST CONCRETE TABLE OF CONTENTS Item Number Page 8100 PRECAST CONCRETE CONSTRUCTION - GENERAL 8-3 8101 General

More information

STUCCO BUILDING PANELS

STUCCO BUILDING PANELS Custom Panel Systems STUCCO BUILDING PANELS General Information Application This concealed fastener, interlocking, exterior wall system provides a flatsurfaced, steel Stucco Building Panel with a textured

More information

INSTALLATION INSTRUCTIONS for Premium Pocket Windows (JII022) IMPoRtaNt INFoRMatIoN & glossary. safety & HaNdlINg

INSTALLATION INSTRUCTIONS for Premium Pocket Windows (JII022) IMPoRtaNt INFoRMatIoN & glossary. safety & HaNdlINg Thank you for selecting JeLd-weN products. Attached are JeLd-weN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to

More information

PHONE: 1-877-238-7278 FAX:

PHONE: 1-877-238-7278 FAX: Kidron Parts Catalog For optimum reliability and full life, insist on the parts that are produced and specified by the engineers who actually designed your Kidron Truck Bodies and Trailers. All authorized

More information