First, unpack the kit
|
|
- Ginger Butler
- 7 years ago
- Views:
Transcription
1 The Arduino diecimila compatible Freeduino board is a special version of the USB diecimila board designed by the Freeduino team using all through-hole components (except FT232RL chip), for easy assembly. The board was designed by Bill Westfield of the Freeduino team. The latest board is v1.22 which schematic is exactly the same as v and V1.20. v1.22 assembles exactly the same as v1.19.1, except for the F1 PTC resettable fuse and it includes the mini USB B socket, already presoldered to the board. First, unpack the kit and start with the PCB. The Freeduino board comes with the FT232RL chip, PTC fuse and mini USB B socket pre-soldered (v1.22 only), eliminating the most difficult task in the assembly process of the Freeduino board. First assemble the USB portion of the board. Identify and separate the following components: R8 Kohm resistor (RLED just below the power LED) C13 4.7uF capacitor (dark yellow, marked 475 or 4.75) LED 3mm green LED C8, C10 100nF ceramic capacitor (brown and round, marked 104) C4 10nF ceramic capacitor (small round brown, marked 103) X1 SV1 SHUNT F1 mini USB B PCB jack (pre-soldered on v1.22) 3 pin male header Black shunt PTC resettable fuse (pre-soldered on v1.22)
2 Solder the parts to the board, in any order. This completes the USB portion of the schematic. Board v1.22 and V1.19.1: the F1 PTC resettable fuse is the blue or green rectangle marked LF050 and it is pre-soldered in the PCB. Board V1.20: the F1 PTC resettable fuse is a through-hole component that looks very similar to a ceramic capacitor, but has markings like XF050. It must be soldered on F1. This is how the PTC fuse for Board V1.20 looks like :
3 And it must be soldered in F1: Plug the small shunt in SV1, shorting central pin and the top pin (USB). Install the FTDI drivers that are installed under the Arduino0009 or Arduino0010 directory. Connect the board to a Mac or PC. The LED in the board lights up and in windows you will hear a beep, indicating that windows identified an USB device. Unplug the USB connector from the board to continue soldering the rest of the components.
4 After testing the USB interface, you can continue soldering the rest of the components, in any order you like. I prefer to complete the power portion of the schematic using the following parts: DC1 DC power jack 2.1 mm barrel type D1 1N4004 diode C5, C12 100nF ceramic capacitor (round brown, marked 104) C6 100uF electrolytic capacitor C7 47uF electrolytic capacitor IC V positive voltage regulator Move the shunt in SV1 to short the central pin and the bottom pin (EXT). This is the indication that the external power supply will be used, instead of USB. Plug a wall plug voltage regulator (+7V to +12V). The LED lights up, indicating that the Power supply is working.
5 The kit can include a ceramic oscillator (orange component with 3 legs) or a crystal plus 2 x 22pF ceramic capacitors (small round brown, marked 22). Picture of the installed ceramic oscillator:
6 Picture of the installed crystal and 22pF ceramic capacitors: Solder the rest of the components: R1 10 Kohm resistor R11, R12 1 Kohm resistor CRS, C1, C9 100nF ceramic capacitor (round brown, marked 104) 13, RX, TX 3mm LED R7, R9, R10 1Kohm resistors (RLED)
7 Now solder the headers and sockets: ICSP RESET POWER, Analog In Digital ATMEGA pin male header reset switch 2 x 6-pin female header 2 x 8-pin female header 28-pin DIP socket Pay special attention to the alignment of the female headers. And finally install the ATmega328 MCU (ATmega168 on older boards).
8 The board is ready to be used. Start Arduino and load the BLINK sketch from the examples directory. Verify that ATmega328 (ATmega168 in older boards) is selected in Tools > Microcontroller (MCU). Select the COM port number corresponding to the USB serial interface. If the port number is high (not in the 1-10 range), then you need to change it using Device Manager (in windows) to use a lower number. Press the Upload to I/O board button in Arduino and the board should autoreset and complete the programming. If you selected correctly the BLINK sketch, the LED L must start blinking once every 2 second (0.5Hz). If you use the new Arduino0010, you don t need to worry about the COM port number being higher than 10 in Windows environment. In previous releases, COM port number needed to be 10 or lower. With Arduino0010, I have tested COM port numbers up to 36 and it is recognized perfectly.
ARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL
ARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL X1: DE-9 serial connector Used to connect computer (or other devices) using RS-232 standard. Needs a serial cable, with at least
More informationPolyBot Board. User's Guide V1.11 9/20/08
PolyBot Board User's Guide V1.11 9/20/08 PolyBot Board v1.1 16 pin LCD connector 4-pin SPI port (can be used as digital I/O) 10 Analog inputs +5V GND GND JP_PWR 3-pin logic power jumper (short top 2 pins
More informationXBee USB Adapter Board (#32400)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationArduino ADK Back. For information on using the board with the Android OS, see Google's ADK documentation.
Arduino ADK Arduino ADK R3 Front Arduino ADK R3 Back Arduino ADK Front Arduino ADK Back Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface
More informationThe $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit.
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit. Micro Wizard has been manufacturing Pinewood Derby timers for over 10 years.
More informationTEECES DOME LIGHTING SYSTEMS
This lighting system was designed by John V (Teeces) to be a simple, customizable, expandable and affordable solution for dome lighting. An Arduino micro-controller is used to tell LED driver chips which
More informationSchematic & Parts List: PIC16F688 Satellite Tracker & Rotor Controller
Fox Delta Amateur Radio Projects & Kits FD- ST1 Schematic & Parts List: PIC16F688 Satellite Tracker & Rotor Controller Introduction to Satellite Antenna Tracking: The ST1 kit/project was designed as an
More informationINTRODUCTION TO SERIAL ARM
INTRODUCTION TO SERIAL ARM A robot manipulator consists of links connected by joints. The links of the manipulator can be considered to form a kinematic chain. The business end of the kinematic chain of
More informationKTA-223 Arduino Compatible Relay Controller
8 Relay Outputs 5A 250VAC 4 Opto-Isolated Inputs 5-30VDC 3 Analog Inputs (10 bit) Connections via Pluggable Screw Terminals 0-5V or 0-20mA Analog Inputs, Jumper Selectable 5A Relay Switching Power Indicator
More informationUser s Manual of Board Microcontroller ET-MEGA2560-ADK ET-MEGA2560-ADK
User s Manual of Board Microcontroller ET-MEGA2560-ADK ET-MEGA2560-ADK Because Arduino that is the development project on AVR MCU as Open Source has been published, it is popular and widespread shortly.
More informationBluetooth + USB 16 Servo Controller [RKI-1005 & RKI-1205]
Bluetooth + USB 16 Servo Controller [RKI-1005 & RKI-1205] Users Manual Robokits India info@robokits.co.in http://www.robokitsworld.com Page 1 Bluetooth + USB 16 Servo Controller is used to control up to
More informationArduino Due Back. Warning: Unlike other Arduino boards, the Arduino Due board runs at 3.3V. The maximum. Overview
R Arduino Due Arduino Due Front Arduino Due Back Overview The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit
More informationPICNet 1. PICNet 1 PIC18 Network & SD/MMC Development Board. Features. Applications. Description
Features PICNet 1 PIC18 Network & SD/MMC Development Board IC Sockets for 28 or 40-pin Microchip PIC18F Microcontrollers IC Socket for 8-pin serial EEPROM Multiple MCU Oscillator sources Full 10BaseT IEEE
More informationYun Shield User Manual VERSION: 1.0. Yun Shield User Manual 1 / 22. www.dragino.com
Yun Shield User Manual VERSION: 1.0 Version Description Date 0.1 Initiate 2014-Jun-21 1.0 Release 2014-Jul-08 Yun Shield User Manual 1 / 22 Index: 1 Introduction... 3 1.1 What is Yun Shield... 3 1.2 Specifications...
More informationTechnical Details and Schematic: A 1200-Baud APRS / Packet Digipeater
Fox Delta Amateur Radio Projects & Kits FoxDigi Technical Details and Schematic: A 1200-Baud APRS / Packet Digipeater Rev: 141208 Completed FoxDigi: Project Introduction: FoxDigi is a PIC16F88 based 1200-Baud
More informationOcean Controls RC Servo Motor Controller
Ocean Controls RC Servo Motor Controller RC Servo Motors: RC Servo motors are used in radio-controlled model cars and planes, robotics, special effects, test equipment and industrial automation. At the
More informationCumbria Designs T-1. SSB/CW Filter kit (4.9152MHz) User Manual
Cumbria Designs T-1 SSB/CW Filter kit (4.9152MHz) User Manual CONTENTS 1 INTRODUCTION 2 2 CIRCUIT DESCRIPTION 2 3 ASSEMBLY 2 4 TESTING 4 The Steading Stainton PENRITH Cumbria CA11 0ES UK 1 Introduction
More informationWarnings: This manual is intended to guide a technicians or customers who would like to repair DBL's
DBL's Service Manual Warnings: This manual is intended to guide a technicians or customers who would like to repair DBL's devices (GoIP, SIM Bank, FXS/FXO gateways) at his/her own risk. DBL SHALL NOT be
More informationSchematic & Parts List: PIC16F688 Satellite Tracker & Rotor Controller
Fox Delta Amateur Radio Projects & Kits FD- ST1 Schematic & Parts List: PIC16F688 Satellite Tracker & Rotor Controller Introduction to Satellite Antenna Tracking: In view to encourage radio amateurs and
More informationDDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1 Page 1
DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be damaged
More informationP105 SINGLE STICK REVERSER PICTURE 1: PCB with headers PICTURE 3: Resistors added PICTURE 5: Add tactile switch (button) PICTURE 7: Fit lead and PIC chip. NOTE! ANTI-STATIC PRECAUTIONS REQUIRED PICTURE
More informationDS1307 Real Time Clock Breakout Board Kit
DS1307 Real Time Clock Breakout Board Kit Created by Tyler Cooper Last updated on 2015-10-15 11:00:14 AM EDT Guide Contents Guide Contents Overview What is an RTC? Parts List Assembly Arduino Library Wiring
More informationAUTOMATIC CALL RECORDER JAMECO PART NO. 2163735
AUTOMATIC CALL RECORDER JAMECO PART NO. 2163735 Experience Level: Intermediate Time Required: 1-2 Hours This project automatically records phone calls. The program, along with the adapter records each
More informationphonostage RIP YOUR VINYL TO BITS, WITH A USB Design
RIP YOUR VINYL TO BITS, WITH A USB phonostage So what do you do with that collection of LPs you have? Sure, they sound great and are fun to listen to, but let s face it, they re not exactly portable. Wouldn
More informationAXE114S BINARY CLOCK. revolution Revolution Education Ltd. Email: info@rev-ed.co.uk Web: www.rev-ed.co.uk Version 1.1 12/09/08 AXE114.PMD.
AXE114S BINARY CLOCK Features: The PICAXE binary clock kit tells the time by lighting up blue LEDs in a binary pattern. This is a useful tool for teaching students binary code or simply just confusing/
More informationMFRD52x. Mifare Contactless Smart Card Reader Reference Design. Document information
Rev. 2.1 17. April 2007 Preliminary Data Sheet Document information Info Keywords Content MFRC522, MFRC523, MFRC52x, MFRD522, MFRD523, Mifare Contactless Smart Card Reader Reference Design, Mifare Reader
More information!Operation:!1. Connect an external power source to J1 (+ and - IN terminals). The
The CB500 Electronic Circuit Breaker is an resettable circuit breaker (fuse) that disconnects power when the trip setting is exceeded. There are 4 trip settings that can easily be changed and set during
More informationUSB to RS-422/485 Serial Adapter
USB to RS-422/485 Serial Adapter User Manual Ver. 2.00 All brand names and trademarks are properties of their respective owners. Contents: Chapter 1: Introduction... 3 1.1 Product Introduction... 3 1.2
More informationTotal solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 Control a relay by means of the wellknown DMX512 protocol. ILLUSTRATED ASSEMBLY MANUAL H8072IP-1 Features
More informationThe CW Machine Hardware
The CW Machine Hardware 2014 Ulrich H. Steinberg The CW Machine Hardware Version 2.2 1 Contents Introduction...3 Connecting the Hardware...4 The Configuration Switches...6 Power Considerations...8 Serial
More informationK128. USB PICmicro Programmer. DIY Electronics (HK) Ltd PO Box 88458, Sham Shui Po, Hong Kong. http://www.kitsrus.com mailto: peter@kitsrus.
K128 USB PICmicro Programmer DIY Electronics (HK) Ltd PO Box 88458, Sham Shui Po, Hong Kong http://www.kitsrus.com mailto: peter@kitsrus.com Last Modified March 31 2003 Board Construction The board is
More informationHands On ECG. Sean Hubber and Crystal Lu
Hands On ECG Sean Hubber and Crystal Lu The device. The black box contains the circuit and microcontroller, the mini tv is set on top, the bars on the sides are for holding it and reading hand voltage,
More informationPN532 NFC RFID Module User Guide
PN532 NFC RFID Module User Guide Version 3 Introduction NFC is a popular technology in recent years. We often heard this word while smart phone company such as Samsung or HTC introduces their latest high-end
More informationUSB / Data-Acquisition Module NOW LEAD-FREE
USB / Data-Acquisition Module NOW LEAD-FREE DLP-TEMP-G Features: Digital I/Os, Analog Inputs (0- Volts) or any combination USB. and.0 Compatible Interface th Generation Silicon from FTDI Supports Up To
More informationSupport: http://www.evilmadscientist.com/forum/
An open-source hardware+software project. For design files and additional documentation, please visit: http://www.evilmadscientist.com/go/diavolino Support: http://www.evilmadscientist.com/forum/ Distributed
More informationRC2200DK Demonstration Kit User Manual
Demonstration Kit User Manual Table of contents TABLE OF CONTENTS... 1 QUICK INTRODUCTION... 2 INTRODUCTION... 3 DEMONSTRATION BOARD... 4 POWER SUPPLY SECTION... 5 RS-232 INTERFACE... 6 CONNECTORS... 7
More informationAndroid Controlled Based Interface
Android Controlled Based Interface Objective Fix Foba Build Rofi (Fifth Generation Robot) Develop, Build, and Implement a Dynamic Balanced Biped Robot Table of Contents Objective... 1 Android Controlled
More informationReal Time Clock USB Evaluation Board V3.0
Real Time Clock USB Evaluation Board V.0 Application Note February 9, 008 RTC EVB Intersil RTC Devices Supported Introduction This evaluation board provides a platform for testing Intersil Real Time Clock
More informationDouble Rainbow tm. Ardweeny Arduino Compatible. It s so Bright and Beautiful!
Double Rainbow RGB LED Strip Controller Shield for the tm Ardweeny Arduino Compatible It s so Bright and Beautiful! wn o eny sh Ardweluded c in t o n Build Time: 0 minutes Skill Level: Intermediate (/5)
More informationPCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod. User Manual. Document version 2.0.1 (2013-08-06)
PCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod User Manual Document version.0. (0-0-0) Products taken into account Product Name Part number Model PCAN-MicroMod Evaluation
More informationM68EVB908QL4 Development Board for Motorola MC68HC908QL4
M68EVB908QL4 Development Board for Motorola MC68HC908QL4! Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com! CONTENTS CAUTIONARY NOTES...3 TERMINOLOGY...3
More informationBUILDING INSTRUCTIONS
etap2hw 38 mm I2C to LCD Interface BUILDING INSTRUCTIONS October 2013 P. Verbruggen Rev 1.01 15-Oct-13 Page 1 Table of Contents Chapter 1 General Information 1.1 ESD Precautions 1.2 Further Supplies 1.3
More informationAdafruit Proto Shield for Arduino
Adafruit Proto Shield for Arduino Created by lady ada Last updated on 2016-08-04 11:06:30 PM UTC Guide Contents Guide Contents Overview Make it! Lets go! Preparation Prep Tools Parts list Parts List Optional
More informationDKWF121 WF121-A 802.11 B/G/N MODULE EVALUATION BOARD
DKWF121 WF121-A 802.11 B/G/N MODULE EVALUATION BOARD PRELIMINARY DATA SHEET Wednesday, 16 May 2012 Version 0.5 Copyright 2000-2012 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes
More informationhttp://arduino.cc/en/main/robot?action=print
Pagina 1 di 7 Arduino : Main / Robot Arduino Robot Robot Top Robot Bottom Overview The Arduino Robot is the first official Arduino on wheels. The robot has two processors, one on each of its two boards.
More informationMassachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.115 Microprocessor Project Laboratory
Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.115 Microprocessor Project Laboratory Connecting your PSoC Evaluation Board It is easy and fun to avoid
More informationUM1724 User manual. STM32 Nucleo boards. Introduction
User manual STM32 Nucleo boards Introduction The STM32 Nucleo board (NUCLEO-F030R8, NUCLEO-F072RB, NUCLEO-F103RB, NUCLEO-F302R8, NUCLEO-F334R8, NUCLEO-F401RE, NUCLEO-F411RE, NUCLEO- L053R8, NUCLEO-L152RE)
More information1-10 The USB PIC K150 microcontroller programmer Hardware version V2.0 File version V2.0 Product Image
1-10 The USB PIC K150 microcontroller programmer Hardware version V2.0 File version V2.0 Product Image 2-10 Product Description: K150 is the latest of a low-cost high-performance PIC programmer, support
More informationIntroduction. Getting familiar with chipkit Pi
Overview: chipkit Pi Introduction chipkit Pi (Designed for Raspberry Pi) is the latest Arduino compatible chipkit platform from Microchip and element14. It features a 32 bit PIC32 microcontroller in a
More informationBoard also Supports MicroBridge
This product is ATmega2560 based Freeduino-Mega with USB Host Interface to Communicate with Android Powered Devices* like Android Phone or Tab using Android Open Accessory API and Development Kit (ADK)
More informationLab 3: PCB design with EAGLE
In this lab you will design a PCB board that will replace all the wires and boards you ve used in the first two labs. 1. Pre-Lab On the website are two EAGLE tutorials. Do them both. Q1. For the first
More informationHow to connect to a Class II router using a mobile-phone data cable specifically for Solwise & Safecom routers
USB to router s serial port How to connect to a Class II router using a mobile-phone data cable specifically for Solwise & Safecom routers by Neo at RouterTech.Org Introduction Routers based on the AR7RD/AR7WRD
More informationUniPi technical documentation REV 1.1
technical documentation REV 1.1 Contents Overview... 2 Description... 3 GPIO port map... 4 Power Requirements... 5 Connecting Raspberry Pi to UniPi... 5 Building blocks... 5 Relays... 5 Digital Inputs...
More informationWeb Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationThe RSGB Centenary Receiver Project Construction Manual
The RSGB Centenary Receiver Project Construction Manual Page 1 of 12 Introduction This project is intended for those new to radio construction. It is a fairly simple receiver for the 14MHz (20m) amateur
More informationCHAPTER 11: Flip Flops
CHAPTER 11: Flip Flops In this chapter, you will be building the part of the circuit that controls the command sequencing. The required circuit must operate the counter and the memory chip. When the teach
More informationYour Multimeter. The Arduino Uno 10/1/2012. Using Your Arduino, Breadboard and Multimeter. EAS 199A Fall 2012. Work in teams of two!
Using Your Arduino, Breadboard and Multimeter Work in teams of two! EAS 199A Fall 2012 pincer clips good for working with breadboard wiring (push these onto probes) Your Multimeter probes leads Turn knob
More informationFTDI VCP DRIVER (free) (WIN/MAC/LINUX) http://www.ftdichip.com/drivers/vcp.htm
002 - CONNECTING THE PRINTER Now that you have an idea what 3D printing entails, we can continue and connect the printer to your computer. First make sure you have a computer with a decent amount of RAM
More informationWorkshop Intel Galileo Board
Workshop Intel Galileo Board Introduction and Basics of Intel Galileo Board Walter Netto November 03th, 2014 Agenda Intel Galileo Board Overview Physical Characteristics Communication Processor Features
More informationObjectives: Part 1: Build a simple power supply. CS99S Laboratory 1
CS99S Laboratory 1 Objectives: 1. Become familiar with the breadboard 2. Build a logic power supply 3. Use switches to make 1s and 0s 4. Use LEDs to observe 1s and 0s 5. Make a simple oscillator 6. Use
More informationGARMIN GPS to PC Wiring Instructions
GARMIN GPS to PC Wiring Instructions Introduction This will outline the basics for connecting most GARMIN GPS receivers to a PC serial connector for data transfer. Since the GPS needs to both send and
More informationPHYS 2P32 Project: MIDI for Arduino/ 8 Note Keyboard
PHYS 2P32 Project: MIDI for Arduino/ 8 Note Keyboard University April 13, 2016 About Arduino: The Board Variety of models of Arduino Board (I am using Arduino Uno) Microcontroller constructd similarly
More informationThe Programming Interface
: In-System Programming Features Program any AVR MCU In-System Reprogram both data Flash and parameter EEPROM memories Eliminate sockets Simple -wire SPI programming interface Introduction In-System programming
More informationPICAXE-28X2 SHIELD BASE (AXE401)
PICAXE-28X2 SHIELD BASE (AXE401) 1.0 Introduction Thank you for purchasing this PICAXE shield base. This datasheet is designed to give a brief introduction to how the shield base is assembled, used and
More informationSYSTEM 4C. C R H Electronics Design
SYSTEM 4C C R H Electronics Design SYSTEM 4C All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, A outputs. Independent 25
More informationTURBO PROGRAMMER USB, MMC, SIM DEVELOPMENT KIT
TURBO PROGRAMMER USB, MMC, SIM DEVELOPMENT KIT HARDWARE GUIDE This document is part of Turbo Programmer documentation. For Developer Documentation, Applications and Examples, see http:/// PRELIMINARY (C)
More informationS88XPressNetLI v1.0. Installation, user and reference manual. 2008 KDesign Electronics, PCB design by RoSoft
S88XPressNetLI v1.0 Installation, user and reference manual 2008 KDesign Electronics, PCB design by RoSoft Table of contents 1 Introduction... 3 2 Specifications... 4 3 Installation... 5 3.1 Connecting
More informationHARDWARE MANUAL. BrightSign HD120, HD220, HD1020. BrightSign, LLC. 16795 Lark Ave., Suite 200 Los Gatos, CA 95032 408-852-9263 www.brightsign.
HARDWARE MANUAL BrightSign HD120, HD220, HD1020 BrightSign, LLC. 16795 Lark Ave., Suite 200 Los Gatos, CA 95032 408-852-9263 www.brightsign.biz TABLE OF CONTENTS OVERVIEW... 1 Block Diagram... 2 Ports...
More informationDOSISYS. Hands Free Reader LDM 210 - LDM 220. User Manual 127356A
DOSISYS LDM 210 - LDM 220 Hands Free Reader User Manual 127356A Publication, translation and reproduction total or partial of this document is strictly forbidden without authorization MGP Instruments
More informationGIE PIC K150 Programmer. User Manual
GIE PIC K150 Programmer User Manual www.gie.com.my Page 1 of 10 Content Overview...3 Supported IC...3 Installation...5 Install PL-2303 Driver (USB to Serial port)...5 Setup For Programming Software...6
More informationModifying the Yaesu FT-847 External 22.625 MHz Reference Input
Modifying the Yaesu FT-847 External 22.625 MHz Reference Input David Smith VK3HZ Introduction This document describes the modification of an FT-847 to allow an external 22.625 MHz Reference oscillator
More informationFreescale Race Challenge 2010 Slot Car Equipment
November 27, 2009 rev 1.1 Freescale Race Challenge 2010 Slot Car Equipment Milan Brejl Freescale Semiconductor, Rožnov p.r., Czech Republic Freescale and the Freescale logo are trademarks of Freescale
More informationR4/F4 Series Master Development System User's Guide
R/F Series Master Development System User's Guide Table of Contents Introduction Ordering Information R/F Series Receiver Development Board Board Objects Initial Setup Troubleshooting The Prototyping
More informationCreating a Project with PSoC Designer
Creating a Project with PSoC Designer PSoC Designer is two tools in one. It combines a full featured integrated development environment (IDE) with a powerful visual programming interface. The two tools
More informationRevision Date: September 19, 2006
RS232 to TTL Cables Revision Date: September 19, 2006 SuperDroid Robots Inc. is incorporated in Wake County, NC USA SuperDroid Robots also does business as Team Half-Life SuperDroid Robots is a registered
More informationUser Guide Reflow Toaster Oven Controller
User Guide Reflow Toaster Oven Controller Version 1.5-01/10/12 DROTEK Web shop: www.drotek.fr SOMMAIRE 1. Introduction... 3 2. Preparation of THE REFLOW CONTROLLER... 4 2.1. Power supply... 4 2.2. USB
More informationArduino Lesson 0. Getting Started
Arduino Lesson 0. Getting Started Created by Simon Monk Last updated on 204-05-22 2:5:0 PM EDT Guide Contents Guide Contents Overview Parts Part Qty Breadboard Installing Arduino (Windows) Installing Arduino
More informationTTL-232R. TTL to USB Serial Converter Range of Cables. Datasheet
Future Technology Devices International Ltd TTL-232R TTL to USB Serial Converter Range of Cables Datasheet Document Reference No.: FT_000054 Version 2.01 Issue Date: 2008-08-28 Future Technology Devices
More informationRS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
More informationAssembly Instructions: Shortwave Radio Kit
Assembly Instructions: Shortwave Radio Kit MTM Scientific, Inc P.O. Box 522 Clinton, MI 49236 U.S.A Introduction Fig 1: The assembled Shortwave Radio Kit The SHORTWAVE RADIO KIT (#SWRAD) from MTM Scientific
More informationPololu DRV8835 Dual Motor Driver Shield for Arduino
Pololu DRV8835 Dual Motor Driver Shield for Arduino Pololu DRV8835 Dual Motor Driver Shield for Arduino, bottom view with dimensions. Overview This motor driver shield and its corresponding Arduino library
More informationICON Server box installation manual Rev. 1.1
ICON Server box installation manual Rev. 1.1 Contents 1.0 About this manual... 3 2.0 Intended use... 3 2.1 European WEEE directive... 3 3.0 Installation and service instructions... 4 Server box overview...
More informationic-mq EVAL MQ1D EVALUATION BOARD DESCRIPTION
Rev A3, Page 1/7 ORDERING INFORMATION Type Order Designation Description and Options Evaluation Board ic-mq EVAL MQ1D ic-mq Evaluation Board ready to operate, accessible through GUI via PC adapter Software
More informationUSBSPYDER08 Discovery Kit for Freescale MC9RS08KA, MC9S08QD and MC9S08QG Microcontrollers User s Manual
USBSPYDER08 Discovery Kit for Freescale MC9RS08KA, MC9S08QD and MC9S08QG Microcontrollers User s Manual Copyright 2007 SofTec Microsystems DC01197 We want your feedback! SofTec Microsystems is always on
More informationPOWERBLOCK - POWER AMPLIFIER
POWERBLOCK - POWER AMPLIFIER This amplifier is an ideal set-up for active speaker use. Total solder points: 383 Difficulty level: beginner 1 2 3 4 5 advanced K8081 ILLUSTRATED ASSEMBLY MANUAL H8081IP-1
More informationSTK500... User Guide
STK500... User Guide Table of Contents Section 1 Introduction... 1-1 1.1 Starter Kit Features...1-1 1.2 Device Support...1-2 Section 2 Getting Started... 2-1 2.1 Unpacking the System...2-1 2.2 System
More informationOWNERS MANUAL. WattsVIEW. Power Monitor Model: DC-10000. http://wattsview.com. WattsVIEWTM. Models: DC-10000 Serial DC-1000 USB DC-25000
WattsVIEW Power Monitor Model: DC-10000 DC Power Monitoring Made Easy Models: DC-10000 Serial DC-1000 USB DC-25000 OWNERS MANUAL PAGE 1 of 23 Table of Contents WattsVIEW Power Monitor Model: DC-10000...1
More informationNOW LEAD-FREE! VCCIO VCCIO RXLED TXLED DTR# 10K FTDI FT232R
DLP--G USB / SERIAL ADAPTER NOW LEAD-FREE! DLP- USB Type 'B' Mini connector to Host PC/ Linux/Mac V VCC USBDP USBDM LED LED DTR# IO Voltage Select Jumper 0K User uc, up, DSP, FPGA Reset External VCC.0
More informationFuture Technology Devices International Ltd. USB to RS232 Serial Converter Range of Cables. Datasheet
Future Technology Devices International Ltd USB to RS232 Serial Converter Range of Cables Datasheet Document Reference No.: FT_000077 Version 1.1 Issue Date: 2008-10-01 Future Technology Devices International
More informationTutorial. replace them with cell-phone operated module. The advantages of a cell-phone operated bot are:-
Tutorial Overview: The basic aim of the project is to find an alternative to the usual RF circuits that are seen so frequently and replace them with cell-phone operated module. The advantages of a cell-phone
More informationWICE-SPI Hardware Operation Manual
Contents 1.Hardware Instruction...1 2. Pin Definition Of WICE-SPI Connector...2 3. Peripheral Circuit Arrangements...3 4. On-Board Programming...4 5. Off-Line Programming...8 1.Hardware Instruction 1.WICE-SPI
More informationThe Radio-Kits Digital SWR meter kit Construction and user manual
The Radio-Kits Digital SWR meter kit Construction and user manual Author - Steve Drury G6ALU List of contents Section Page no. 1. Features and specifications 2 2. Introduction 2. Construction 4. General
More informationConnecting External Resources
Connecting External esources This section describes how to connect the following external resources to Expression 303: power network external sound system SMAT Board guest laptop Connecting the Power Cord
More informationTTL-232R-PCB. TTL to USB Serial Converter PCB. Datasheet
Future Technology Devices International Ltd TTL-232R-PCB TTL to USB Serial Converter PCB Datasheet Document Reference No.: FT_000065 Version 1.01 Issue Date: 2010-09-02 Future Technology Devices International
More informationThe self-starting solar-powered Stirling engine
The self-starting solar-powered Stirling engine This project began at the request of an artist who had proposed a Stirling-engine-powered sculpture to a client. The engine only had to run, not really produce
More informationBUILD YOUR OWN RC SWITCH (Issue 3)
PART ONE SINGLE ELECTRONIC RC SWITCH Fancy switching the lights using your radio, then here is a circuit you may consider building. It only uses one IC and seven other components for a single switch and
More informationDIY KIT 140. Telephone Switcher MK2
This device connects to the telephone line and can be used to remotely control up to 4 relay outputs using a DTMF (tone dialing) telephone. A number of user settings are available to improve the useability
More informationIntroducing AVR Dragon
Introducing AVR Dragon ' Front Side Back Side With the AVR Dragon, Atmel has set a new standard for low cost development tools. AVR Dragon supports all programming modes for the Atmel AVR device family.
More informationES-299A NTP Time Server. Operation and Maintenance Manual. 142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.
ES-299A NTP Time Server Operation and Maintenance Manual 142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com TABLE OF CONTENTS 1.0 INTRODUCTION...1 2.0 STANDARD FEATURES...1
More informationSM1231 USER GUIDE SM1231 RF MODULE USER GUIDE
SM1231 RF MODULE Revision 1.0 11/2009 Page 1 of 8 www.semtech.com Table of Contents Table of Contents...2 Index of Figures...2 Index of Tables...2 1 Introduction...3 2 Reference Design...3 3 PCB Layout...6
More information