Order codes. TO-220 D²PAK (tape and reel) TO-220FP TO-3 LM117K LM217T LM217D2T-TR LM217K LM317T LM317D2T-TR LM317P LM317K

Transcription

1 LM117 LM217, LM V to 37 V adjustable voltage regulators Features Output voltage range: 1.2 to 37 V Output current in excess of 1.5 A 0.1% Line and load regulation Floating operation for high voltages Complete series of protections: current limiting, thermal shutdown and SOA control Description The LM117, LM217, LM317 are monolithic integrated circuits in TO-220, TO-220FP, TO-3 and D²PAK packages intended for use as positive adjustable voltage regulators. They are designed to supply more than 1.5 A of load current with an output voltage adjustable over a 1.2 to 37 V range. The nominal output voltage is selected by means of only a resistive divider, making the device exceptionally easy to use and eliminating the stocking of many fixed regulators. TO-220 D²PAK TO-220FP TO-3 Table 1. Device summary Order codes TO-220 D²PAK (tape and reel) TO-220FP TO-3 LM117K LM217T LM217D2T-TR LM217K LM317T LM317D2T-TR LM317P LM317K March 2010 Doc ID 2154 Rev 15 1/

2 Contents LM117, LM217, LM317 Contents 1 Pin configuration Maximum ratings Diagram Electrical characteristics Typical characteristics Application information Package mechanical data Revision history /25 Doc ID 2154 Rev 15

3 LM117, LM217, LM317 Pin configuration 1 Pin configuration Figure 1. Pin connections (top view) TO-220 TO-220FP D²PAK (Any Type) TO-3 Doc ID 2154 Rev 15 3/25

4 Maximum ratings LM117, LM217, LM317 2 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit V I - V O Input-reference differential voltage 40 I O Output current Internally limited V LM to 150 T OP Operating junction temperature for: LM to 150 C LM317 0 to 125 P D Power dissipation Internally limited T STG Storage temperature -65 to 150 C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Table 3. Thermal data Symbol Parameter D²PAK TO-220 TO-220FP TO-3 Unit R thjc Thermal resistance junction-case C/W R thja Thermal resistance junction-ambient C/W 4/25 Doc ID 2154 Rev 15

5 LM117, LM217, LM317 Diagram 3 Diagram Figure 2. Schematic diagram Doc ID 2154 Rev 15 5/25

6 Electrical characteristics LM117, LM217, LM317 4 Electrical characteristics Table 4. V I - V O = 5 V, I O = 500 ma, I MAX = 1.5 A and P MAX = 20 W, T J = - 55 to 150 C for LM117, T J = - 25 to 150 C for LM217, unless otherwise specified. Electrical characteristics for LM117/LM217 Symbol Parameter Test conditions Min. Typ. Max. Unit ΔV O Line regulation V I - V O = 3 to 40 V T J = 25 C V O 5 V T J = 25 C 5 15 ΔV O Load regulation I O = 10 ma to I MAX V O 5 V, T J = 25 C I O = 10 ma to I MAX I ADJ Adjustment pin current µa ΔI ADJ Adjustment pin current V I - V O = 2.5 to 40V I O = 10 ma to I MAX µa V REF Reference voltage (between pin 3 and pin 1) V I - V O = 2.5 to 40V I O = 10 ma to I MAX P D P MAX V ΔV O /V O Output voltage temperature stability 1 % I O(min) Minimum load current V I - V O = 40 V ma I O(max) en Maximum load current Output noise voltage (percentage of V O ) SVR Supply voltage rejection (1) T J = 25 C, f = 120Hz 1. C ADJ is connected between pin 1 and ground. V I - V O 15 V, P D < P MAX V I - V O = 40 V, P D < P MAX, T J = 25 C 0.4 B = 10Hz to 100kHz, T J = 25 C % C ADJ =0 65 C ADJ =10µF %/V mv % A db 6/25 Doc ID 2154 Rev 15

7 LM117, LM217, LM317 Electrical characteristics Table 5. V I - V O = 5 V, I O = 500 ma, I MAX = 1.5 A and P MAX = 20 W, T J = 0 to 125 C, unless otherwise specified. Electrical characteristics for LM317 Symbol Parameter Test conditions Min. Typ. Max. Unit ΔV O Line regulation V I - V O = 3 to 40 V T J = 25 C V O 5 V T J = 25 C 5 25 ΔV O Load regulation I O = 10 ma to I MAX V O 5 V, T J = 25 C I O = 10 ma to I MAX I ADJ Adjustment pin current µa ΔI ADJ V REF Adjustment pin current Reference voltage (between pin 3 and pin 1) V I - V O = 2.5 to 40V, I O = 10 ma to 500mA %/V mv % µa V I - V O = 2.5 to 40V I O = 10 ma to 500mA P D P MAX V ΔV O /V O Output voltage temperature stability 1 % I O(min) Minimum load current V I - V O = 40 V ma I O(max) en Maximum load current Output noise voltage (percentage of V O ) SVR Supply voltage rejection (1) T J = 25 C, f = 120Hz 1. C ADJ is connected between pin 1 and ground. V I - V O 15 V, P D < P MAX V I - V O = 40 V, P D < P MAX, T J = 25 C 0.4 B = 10Hz to 100kHz, T J = 25 C % C ADJ =0 65 C ADJ =10µF A db Doc ID 2154 Rev 15 7/25

8 Typical characteristics LM117, LM217, LM317 5 Typical characteristics Figure 3. Output current vs. input-output differential voltage Figure 4. Dropout voltage vs. junction temperature Figure 5. Reference voltage vs. junction Figure 6. Basic adjustable regulator 8/25 Doc ID 2154 Rev 15

9 LM117, LM217, LM317 Application information 6 Application information The LM117, LM217, LM317 provides an internal reference voltage of 1.25 V between the output and adjustments terminals. This is used to set a constant current flow across an external resistor divider (see Figure 3), giving an output voltage V O of: V O = V REF (1 + R 2 /R 1 ) + I ADJ R 2 The device was designed to minimize the term I ADJ (100 µa max) and to maintain it very constant with line and load changes. Usually, the error term I ADJ R 2 can be neglected. To obtain the previous requirement, all the regulator quiescent current is returned to the output terminal, imposing a minimum load current condition. If the load is insufficient, the output voltage will rise. Since the LM117, LM217, LM317 is a floating regulator and "sees" only the input-to-output differential voltage, supplies of very high voltage with respect to ground can be regulated as long as the maximum input-to-output differential is not exceeded. Furthermore, programmable regulator are easily obtainable and, by connecting a fixed resistor between the adjustment and output, the device can be used as a precision current regulator. In order to optimize the load regulation, the current set resistor R 1 (see Figure 3) should be tied as close as possible to the regulator, while the ground terminal of R 2 should be near the ground of the load to provide remote ground sensing. Performance may be improved with added capacitance as follow: An input bypass capacitor of 0.1 µf An adjustment terminal to ground 10 µf capacitor to improve the ripple rejection of about 15 db (CADJ). An 1 µf tantalum (or 25 µf Aluminium electrolytic) capacitor on the output to improve transient response. In additional to external capacitors, it is good practice to add protection diodes, as shown in Figure 4 D1 protect the device against input short circuit, while D2 protect against output short circuit for capacitance discharging. Figure 7. Voltage regulator with protection diodes Note: D1 protect the device against input short circuit, while D2 protects against output short circuit for capacitors discharging. Doc ID 2154 Rev 15 9/25

10 Application information LM117, LM217, LM317 Figure 8. Slow turn-on 15 V regulator Figure 9. Current regulator I O = (V REF / R 1 ) + I ADJ = 1.25 V / R 1 Figure V electronic shut-down regulator 10/25 Doc ID 2154 Rev 15

11 LM117, LM217, LM317 Application information Figure 11. Digitally selected outputs (R 2 sets maximum V O ) Figure 12. Battery charger (12 V) * R S sets output impedance of charger Z O = R S (1 + R 2 /R 1 ). Use of R S allows low charging rates whit fully charged battery. Doc ID 2154 Rev 15 11/25

12 Application information LM117, LM217, LM317 Figure 13. Current limited 6 V charger * R3 sets peak current (0.6 A for 1 0). ** C1 recommended to filter out input transients. 12/25 Doc ID 2154 Rev 15

13 LM117, LM217, LM317 Package mechanical data 7 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. Table 6. Dim. TO-220 mechanical data Type STD - ST Dual Gauge mm. Type STD - ST Single Gauge mm. Min. Typ. Max. Min. Typ. Max. A b b c D D E e e F H J L L L L P Q Doc ID 2154 Rev 15 13/25

14 Package mechanical data LM117, LM217, LM317 Figure 14. Drawing dimension TO-220 (type STD-ST Dual Gauge) /A Note: 1 Max resin gate protrusion: 0.5 mm. 2 Resin gate position is accepted in each of the two positions shown on the dwg, or their symmetrical. 14/25 Doc ID 2154 Rev 15

15 LM117, LM217, LM317 Package mechanical data Figure 15. Drawing dimension TO-220 (type STD-ST Single Gauge) _B Note: In spite of some difference in tolerances, the packages are compatible. Doc ID 2154 Rev 15 15/25

16 Package mechanical data LM117, LM217, LM317 Figure 16. Drawing dimension tube for TO-220 Dual Gauge (mm.) Figure 17. Drawing dimension tube for TO-220 Single Gauge (mm.) 16/25 Doc ID 2154 Rev 15

17 LM117, LM217, LM317 Package mechanical data TO-3 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A B C D E G N P R U V P G A D C N O U V B E R P003C/C Doc ID 2154 Rev 15 17/25

18 Package mechanical data LM117, LM217, LM317 TO-220FP mechanical data Dim. mm. inch. Min. Typ Max. Min. Typ. Max. A B D E F F F G G H L L L L L L DIA A-H 18/25 Doc ID 2154 Rev 15

19 LM117, LM217, LM317 Package mechanical data Figure 18. Drawing dimension D²PAK (type STD-ST) /L Doc ID 2154 Rev 15 19/25

20 Package mechanical data LM117, LM217, LM317 Figure 19. Drawing dimension D²PAK (type WOOSEOK-SUBCON.) /L 20/25 Doc ID 2154 Rev 15

21 LM117, LM217, LM317 Package mechanical data Table 7. Dim. D²PAK mechanical data Type STD-ST mm. Type WOOSEOK-Subcon. mm. MIN. TYP. MAX. MIN. TYP. MAX. A A b b c c D D E E e e H J L L L R V Note: The D²PAK package coming from the subcontractor Wooseok is fully compatible with the ST's package suggested footprint. Doc ID 2154 Rev 15 21/25

22 Package mechanical data LM117, LM217, LM317 Figure 20. D²PAK footprint recommended data Table 8. Footprint data Values Dim. mm. inch. A B C D E F G /25 Doc ID 2154 Rev 15

23 LM117, LM217, LM317 Package mechanical data Tape & reel D 2 PAK-P 2 PAK-D 2 PAK/A-P 2 PAK/A mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A C D N T Ao Bo Ko Po P Doc ID 2154 Rev 15 23/25

24 Revision history LM117, LM217, LM317 8 Revision history Table 9. Document revision history Date Revision Changes 01-Sep Mistake V REF ==> V O, tables 1, 4 and Jan Jun Nov Added Table Feb Mar D²PAK mechanical data has been updated, add footprint data and the document has been reformatted. Change values ΔI ADJ and V REF test condition of I O = 10 ma to I MAX ==> I O = 10 ma to 500 ma on Table 5. Added: TO-220 mechanical data Figure 14 on page 14 and Table 6 on page 13. Added: notes Figure 14 on page 14, Figure 15 on page 15, Figure 16 and Figure 17 on page /25 Doc ID 2154 Rev 15

25 LM117, LM217, LM317 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America Doc ID 2154 Rev 15 25/25