ACT Gold Level Used Equipment Prep Checklist for Internal Combustion equipment Warranty 45 day full, 90 day powertrain
|
|
|
- Albert Wright
- 7 years ago
- Views:
Transcription
1 ACT Gold Level Used Equipment Prep Checklist for Internal Combustion equipment Warranty 45 day full, 90 day powertrain 1. Drain engine oil, inspect, and replace with new oil, and replace engine oil filter. 2. Replace air filter. 3. Inspect engine performance at idle and while accelerating and adjust accordingly. 4. Inspect for fuel system for fuel leakage. 5. Inspect fan belt tension, looseness and damage, and replace if necessary. 6. Inspect transmission operating mechanism function and looseness. 7. Inspect power steering for oil leak and looseness of mounting and linkage. Inspect for damage of power steering hose. 8. Inspect parking brake operating force, and adjust tension, if needed. 9. Inspect brake reservoir tank for leak, flush brake system with new fluid. 10. Inspect mast channels and carriage for deformation and damage of each part and for cracks at welds. 11. Inspect chains for tension, deformation and damage. 12. Inspect hydraulic cylinder operation and check for oil leaks and damage. Inspect hydraulic tank for leak. 13. Inspect wiring harness for damage and condition of fuse. 14. Inspect safety equipment to verify it meets OSHA requirements. 15. Inspect tires for cuts, damage, uneven wearing, and proper air pressure. Replace tires to customer order type. 16. Inspect tires for loose rim and hub nuts and tighten. 17. Replace spark plugs / plug wires and adjust ignition timing, if needed. 18. Replace distributor cap and distributor rotor, if needed. 19. Use LPG regulator rebuild kit, if needed. (over 3,000 hours since last rebuild) 20. Replace PCV valve, if applicable. 21. Inspect transmission and differential for leaks. Drain and refill transmission and differential. 22. Inspect rollers for wear, damage and rotating condition. 23. Inspect side shift slides and replace as needed. 24. Flush cooling system and refill with fresh coolant. Check radiator hoses for degradation. 25. Inspect brake drum wear and damage. 26. Inspect brake shoe operating condition. 27. Adjust brake shoe clearance to drum. 28. Drain hydraulic tank and clean strainer. 29. Replace hydraulic oil filter and hydraulic oil. 30. Verify equipment has the owner s manual as well as accurate and readable manufacturer data tag. Approved by:
2 ACT Gold Level Used Equipment Prep Checklist for Electric Forklift Warranty 45 day full, 180 day powertrain, 180 day battery warranty 1. Inspect transmission operating mechanism function and looseness. 2. Inspect differential for leaks, drain and refill differential. 3. Inspect electric motor brushes and replace as needed. 4. Inspect power steering for oil leak and looseness of mounting and linkage. 5. Inspect for damage of power steering hose. 6. Inspect brake reservoir tank for leak, flush brake system with newfluid. 7. Inspect mast channels and carriage for deformation and damage of each part and for cracks at welds. 8. Inspect chains for tension, deformation and damage. 9. Inspect hydraulic cylinder operation and check for oil leaks and damage. 10. Inspect hydraulic tank for leak. 11. Inspect wiring harness for damage and condition of fuse. 12. Inspect safety equipment to verify it meets OSHA requirements. 13. Inspect tires for cuts, damage, uneven wearing, and proper air pressure. 14. Inspect tires for loose rim and hub nuts and tighten. 15. Inspect side shift slides and replace as needed. 16. Inspect transmission and differential for leaks. 17. Drain and refill transmission and differential, if needed. 18. Inspect mast and carriage rollers for wear, damage and rotating condition. 19. Replace transmission oil filter. 20. Inspect brake drum wear and damage. 21. Inspect brake shoe operating condition. 22. Adjust parking brake cable tension. 23. Adjust brake shoe clearance to drum. 24. Drain hydraulic tank and clean strainer. 25. Replace hydraulic oil filter and hydraulic oil, if needed. 26. Replace tires to customer order type. If non-marking tires, verify and add static strap as needed. 27. Verify equipment has the owner s manual as well as accurate and readable manufacturer data tag. 28. On battery powered equipment, if used battery is included in sale; recondition battery including new cables, connector, paint, acid adjustment, and testing. 29. On battery powered equipment, if used charger is included in the sale; set voltage to match customer input voltage, test charger for proper operation. Approved by:
3 ACT Gold Level Used Equipment Prep Checklist for Electric Pallet Jack Warranty 45 day full, 180 day powertrain, 180 day battery warranty 1. Inspect and lubricate steer bearing. 2. Replace drive and pump motor brushes, if needed. 3. Inspect controls for excessive wear and operation of emergency reverse button. 4. Inspect hydraulic cylinder operation and check for oil leaks and damage. 5. Inspect hydraulic tank for leak. 6. Inspect wiring harness for damage and condition of fuse. 7. Inspect safety equipment to verify it meets OSHA requirements. 8. Inspect undercarriage and replace components, if needed. 9. Inspect tires, wheel, and casters for cuts, damage, and uneven wearing. 10. Drain hydraulic tank and clean strainer. 11. Replace hydraulic oil filter and hydraulic oil. 12. Replace drive tire to customer order type. 13. Verify equipment has the owner s manual as well as accurate and readable manufacturer data tag. 14. On battery powered equipment, if used battery is included in sale; recondition battery including new cables, connector, paint, acid adjustment, and testing. 15. On battery powered equipment, if used charger is included in the sale; set voltage to match customer input voltage, test charger for proper operation. Approved by:
4 ACT Silver Level - Used Prep Checklist for Internal Combustion equipment Warranty 30 day full, 30 day powertrain 1. Complete oil and filter replacement service. 2. Inspect transmission operating mechanism function and looseness. 3. Inspect power steering for oil leak and looseness of mounting and linkage. 4. Inspect for damage of power steering hose. 5. Inspect parking brake operating force. 6. Inspect brake reservoir tank for leak and fluid level. 7. Inspect mast channels and carriage for deformation and damage of each part and for cracks at welds. 8. Inspect chains for tension, deformation and damage. 9. Inspect hydraulic cylinder operation and check for oil leaks and damage. Inspect hydraulic tank for leak. 10. Inspect wiring harness for damage and condition of fuse. 11. Inspect safety equipment to verify it meets OSHA requirements. 12. Inspect tires for cuts, damage, uneven wearing, and proper air pressure. 13. Inspect tires for loose rim and hub nuts and tighten. 14. Inspect rollers for wear, damage and rotating condition. 15. Replace transmission oil filter, if needed Replace hydraulic oil filter and hydraulic oil, if needed. 17. Verify equipment has the owner s manual and accurate and readable manufacturer data tag. 18. Check battery to verify accepts charge and that leads and connector are safe for operation. 19. Check charger to verify the input voltage and phase match customer specifications provided in order. Approved by:
5 ACT Silver Level - Used Prep Checklist for Electric Forklift Warranty 30 day full, 60 day powertrain 1. Inspect transmission operating mechanism function and looseness. 2. Inspect power steering for oil leak and looseness of mounting and linkage. 3. Inspect for damage of power steering hose. 4. Inspect parking brake operating force. 5. Inspect brake reservoir tank for leak and fluid level. 6. Inspect mast channels and carriage for deformation and damage of each part and for cracks at welds. 7. Inspect chains for tension, deformation and damage. 8. Inspect hydraulic cylinder operation and check for oil leaks and damage. Inspect hydraulic tank for leak. 9. Inspect wiring harness for damage and condition of fuse. 10. Inspect safety equipment to verify it meets OSHA requirements. 11. Inspect tires for cuts, damage, uneven wearing, and proper air pressure. 12. Inspect tires for loose rim and hub nuts and tighten. 13. Inspect rollers for wear, damage and rotating condition. 14. Replace hydraulic oil filter and hydraulic oil, if needed. 15. Verify equipment has the owner s manual. 16. Verify forklift has accurate and readable manufacturer data tag. 17. Check battery to verify accepts charge and that leads and connector are safe for operation. 18. Check charger to verify the input voltage and phase match customer specifications provided in order. Approved by:
6 ACT Silver Level - Used Prep Checklist for Electric Pallet Jack Warranty 30 day full, 60 day powertrain 1. Verify operational buttons including lift, lower, high speed, emergency reverse function, and horn. 2. Inspect brake reservoir tank for leak and fluid level. 3. Inspect hydraulic cylinder operation and check for oil leaks and damage. Inspect hydraulic tank for leak. 4. Inspect wiring harness for damage and condition of fuse. 5. Inspect safety equipment to verify it meets OSHA requirements. 6. Inspect tires for cuts, damage, uneven wearing, and proper air pressure. 7. Replace hydraulic oil filter and hydraulic oil, if needed. 8. Verify equipment has the owner s manual and lift has accurate and readable manufacturer data tag. 9. Check battery to verify accepts charge and that leads and connector are safe for operation. 10. Check charger to verify the input voltage and phase match customer specifications provided in order. Approved by:
7 ACT Bronze Level - Used Prep Checklist Warranty 30 day powertrain 1. Drain engine oil, inspect, and replace with new oil, and replace engine oil filter. 2. Replace air filter. 3. Inspect coolant level in radiator and refill if needed. 4. Inspect fan belt tension, looseness and damage, and replace if necessary. 5. Measure tire inflation pressure, if applicable. 6. Inspect parking brake operating force. 7. Inspect chains for tension, deformation and damage. 8. Inspect safety equipment to verify it meets OSHA requirements. 9. Inspect tires for loose rim and hub nuts and tighten. 10. Inspect side shift slides and replace as needed. Approved by:
PUMP MAINTENANCE SCHEDULE AND CHECKLISTS
PUMP MAINTENANCE SCHEDULE AND CHECKLISTS Providing a maintenance schedule defined specifically by run hours or yardage pumped serves only as a general guideline given the large amount of variables a unit
Scheduled Maintenance (North America)
Scheduled Maintenance (North America) Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions apply. f any do apply, follow Schedule 2 (Canada and Puerto Rico residents
Duramax Maintenance Info
The following maintenance schedule was arranged using information from GM, OEM manufacturers and personal experience. It does not represent the standard and should only be used as reference, you may choose
UDOT RPMS VEHICLE RECORDS, PREVENTIVE MAINTENANCE & SURVEILLANCE
UDOT RPMS VEHICLE RECORDS, PREVENTIVE MAINTENANCE & SURVEILLANCE VEHICLE RECORDS AND PREVENTIVE MAINTENANCE Prepared by: UTAH DEPARTMENT OF TRANSPORTATION OFFICE OF PLANNING AND PROGRAMMING IN COOPERATION
UNITED STATES AND U.S. TERRITORIES AND POSSESSIONS EXCEPT PUERTO RICO 2016 / WARRANTY & MAINTENANCE MANUAL
UNITED STATES AND U.S. TERRITORIES AND POSSESSIONS ECEPT PUERTO RICO 2016 / WARRANTY & MAINTENANCE MANUAL Maintenance Service precautions Vehicle maintenance is an important yet frequently neglected item.
PREVENTION MAINTENANCE CHECKLIST FOR TRACTORS, TRUCKS, AND AUTOMOBILES
PREVENTION MAINTENANCE CHECKLIST FOR TRACTORS, TRUCKS, AND AUTOMOBILES Farm Machinery Fact Sheet FM-21 By Dr. Von H. Jarrett, Extension Agricultural Engineer Systematic sequence for inspection GASOLINE
J & Z Automotive Repair www.jandzauto.com 1451 Teaneck road, Teaneck, NJ 07666
J & Z Automotive Repair www.jandzauto.com 1451 Teaneck road, Teaneck, NJ 07666 Office: 201-833-8398 E-mail: service@jandzauto.com Monthly Maintenance Checklist Taking your vehicle to your Gemini Automotive
Heavy Duty Equipment Mechanic (Class Code 3743) Task List. Inspection and Diagnosis
Heavy Duty Equipment Mechanic (Class Code 3743) Task List Inspection and Diagnosis In order to verify complaints and determine malfunctions a Heavy Duty Mechanic: 1. Reads operators written trouble reports,
City of Tampa Employment Services Division FLEET MECHANIC APPLICATION SUPPLEMENT
City of Tampa Employment Services Division FLEET MECHANIC APPLICATION SUPPLEMENT Check the job(s) for which you are applying: Fleet Mechanic I Fleet Mechanic II Fleet Mechanic III NAME Date: Please read
AUTOMOBILE MECHANIC STUDENT INTERNSHIP SKILLS LIST Provo School District
AUTOMOBILE MECHANIC STUDENT INTERNSHIP SKILLS LIST Provo School District Repairs and overhauls automobiles, buses, trucks, and other automotive vehicles: Examines vehicle and discusses with customer or
Topics of the Presentation
Drill Rig Safety Topics of the Presentation Personnel safety and monitoring PPE Health (Drugs and Alcohol) Drill Rig operation Safe set up procedures Safe operation of machine Safety related accidents
Federal Wage System Job Grading Standard For Mobile Equipment Servicing, 5806. Table of Contents
Federal Wage System Job Grading Standard For Mobile Equipment Servicing, 5806 Table of Contents WORK COVERED... 2 WORK NOT COVERED...2 TITLES... 2 GRADE LEVELS... 2 MOBILE EQUIPMENT SERVICES, GRADE-1...
Apprenticeship Training Standard. Automotive Service Technician. Trade Code: 310S
Apprenticeship Training Standard Automotive Service Technician Trade Code: 310S Development Date: January 2003 Please Note: Apprenticeship Training and Curriculum Standards were developed by the Ministry
Kobelco Extended Warranty Program. www.kobelco-europe.com
Kobelco Extended Warranty Program www.kobelco-europe.com Kobelco Extended Warranty is a convenient, value added way to give your Kobelco customers added security and peace of mind. Benefits of the Kobelco
356 CHECKLIST ELECTRICAL: CHASSIS:
356 CHECKLIST ELECTRICAL: Headlights hi/lo beam Taillights Running lights Turn signals Brake lights License light(s) Fog lights Reverse light Horn Dome lights Dash lights Temp guage Tank level guage Tachometer
WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW?
WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performed
DIESEL TRUCK MECHANIC 47.0605 GENERAL SKILLS. *A. 001 Define specific safety terms.
DIRECTIONS Evaluate the student by checking the appropriate box to indicate the degree of Competency. The rating for each task should reflect employability readiness rather than the grades given in class.
VOLVO PENTA 2+ 3 FACTORY PROTECTION PROGRAM. A New Generation of Customer Care for Today s New Technology Engines
VOLVO PENTA 2+ 3 FACTORY PROTECTION PROGRAM A New Generation of Customer Care for Today s New Technology Engines A New Generation of Customer Care Volvo Penta provides a factory-backed, factory-administered
Customer Owned Certified
TEREX BENFORD TA30 Customer Owned Certified OFF HIGHWAY TRUCKS Inspection Number: 751979 Serial #: A7991472 Date Created: 07/27/2011 07:46:05 AM CDT Engine Serial #: N/A Last Updated: 08/02/2011 07:10:48
Extended Protection Plans for New and Pre-Owned Vehicles
Extended Protection Plans for New and Pre-Owned Vehicles Extended Protection you can count on from Old Republic Insured Automotive Services, Inc. (ORIAS) Your vehicle is a major investment. Next to your
Palm Beach County Fleet Management Asset Maintenance History
Workorder: 34963 Meter Reading: 582 In Date: 02/18/2000 Close Date: 02/25/2000 R&R Seat Road And Bridge And Back. Charge: REPLACE SEAT 1.50 SEAT ASSY. HE1300 1.00 216.42 Charge: 67.50 Workorder: 39566
For your safety, read carefully and keep in this vehicle. INFINITI SERVICE AND MAINTENANCE GUIDE
For your safety, read carefully and keep in this vehicle. 2006 INFINITI SERVICE AND MAINTENANCE GUIDE For your safety, read carefully and keep in this vehicle. 2006 INFINITI SERVICE AND MAINTENANCE GUIDE
Lancair Legacy Annual Condition Inspection Checklist
Lancair Legacy Annual Condition Inspection Checklist Performed by: Completion Date: Complete Maintenance/Inspection Item Comments Pre-Inspection Research AD and Service bulletins Inspect entire airframe
Maintenance Service Operations
Maintenance Requirements miles x 1000 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 All 2009 Models km x 1000 12 24 36 48 60 72 84 96 108 120 Engine PCV, inspect, clean nipple and hoses (5 cylinder engine VIN
For your safety, read carefully and keep in this vehicle. INFINITI SERVICE AND MAINTENANCE GUIDE
For your safety, read carefully and keep in this vehicle. 2008 INFINITI SERVICE AND MAINTENANCE GUIDE VEHICLE IDENTIFICATION Vehicle Identification Number (VIN) Delivery Date Warranty Start Date Mileage
6-years/75,000 miles Comprehensive coverage Subsequent Owner Warranty $100 Deductible
LINCOLN PREMIER LIMITED WARRANTY 6-years/75,000 miles Comprehensive coverage Subsequent Owner Warranty $100 Deductible Comprehensive Coverage Because Lincoln has always been a brand you can trust and respect,
BUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide
BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents
Working Copy WP 05-WH1401. Revision 4. 6-Ton Electric Forklifts 74-H-010B. Technical Procedure EFFECTIVE DATE: 01/04/06. John Guy APPROVED FOR USE
WP 05-WH1401 Revision 4 6-Ton Electric Forklifts 74-H-010B Technical Procedure EFFECTIVE DATE: 01/04/06 John Guy APPROVED FOR USE WP 05-WH1401 Rev. 4 Page 2 of 10 TABLE OF CONTENTS INTRODUCTION... 3 REFERENCES...
MAINTENANCE OF WHEELMOVE IRRIGATION SYSTEMS
MAINTENANCE OF WHEELMOVE IRRIGATION SYSTEMS F. Richard Beard, Agricultural Equipment, Structures and Electricity Robert W. Hill, Biological & Irrigation Engineering Boyd Kitchen, Uintah County Extension
Vehicle Maintenance Policies and Procedures
Vehicle Maintenance Policies and Procedures Adopted: 09/20/2011 1 Table of Contents Introduction:... 4 Goals and objectives:... 5 Goals:... 5 Objectives:... 5 Preventative Maintenance:... 6 Daily... 6
SUSPENSION DIAGNOSIS
SECTION 2A SUSPENSION DIAGNOSIS TABLE OF CONTENTS Diagnosis... 2A-2 General Diagnosis... 2A-2 Hub and Bearing... 2A-7 2A-2 SUSPENSION DIAGNOSIS DIAGNOSIS GENERAL DIAGNOSIS Problems in the steering, the
Class 5 to 7 Truck and Bus Hydraulic Brake System
Class 5 to 7 Truck and Bus Hydraulic Brake System Diagnostic Guide 1st Edition * 5+0 Important Service tes The information in this publication was current at the time of printing. The information presented
VICE PRESIDENT, DELIVERY OPERATIONS. Management Alert Suspension or Delay of Scheduled Vehicle Maintenance (Report Number DR-MA-15-001)
February 10, 2015 MEMORANDUM FOR: EDWARD F. PHELAN, JR. VICE PRESIDENT, DELIVERY OPERATIONS E-Signed by Robert Batta VERIFY authenticity with e-sign FROM: SUBJECT: Robert J. Batta Deputy Assistant Inspector
FORKLIFT SAFETY BASICS & OPERATOR S DAILY CHECKLIST
GUIDE TO FORKLIFT SAFETY BASICS & OPERATOR S DAILY CHECKLIST PROVIDED BY 1 Emilcott Over 25 Years Of Environmental, Health and Safety Professional Consulting Experience Find out how Emilcott can help your
Cooling system components, removing and installing
Page 1 of 34 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
Apprenticeship Training Standard. Automotive Service Technician. Trade Code: 310S
Apprenticeship Training Standard Automotive Service Technician Trade Code: 310S Development Date: January 2003 CONTENTS PAGE Apprenticeship Program Summary/Guidelines... 2 Competency Analysis Profile...
MAINTENANCE PROTECTIONPLAN
LET FORD PROTECT YOU ON THE ROAD AHEAD TRAVELLING WELL WITH FORD PROTECTION PLAN (FMPP) CONFIDENCE FOR THE ROAD AHEAD When you decide to purchase or lease your vehicle, you want the peace of mind that
TRAILER MATE SPECIFICATIONS. TM50 2-Wheel Drive 3-Wheel Drive
TRAILER MATE SPECIFICATIONS TM50 2-Wheel Drive 3-Wheel Drive TABLE OF CONTENTS TM50 2-WD / 3-WD Specifications / Dimensions. 1 General Specifications.... 2 Weights / Travel Speed / Tilt Table Degrees /
REMOVAL AND INSTALLATION
303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214
13. REAR WHEEL/BRAKE/SUSPENSION
13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...
Automotive Technology II. General Service Technician Task List Individual Training Plan
Automotive Technology II General Service Technician Task List Individual Training Plan Student Name: Period: Instructor Name: Sherman Martinez WEEK A. Introduction to Auto Shop and Personal Safety ",'
Intake Manifold: Service and Repair
2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 Copyright 2008, ALLDATA 9.90 Page 1 Intake Manifold: Service and Repair Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement.
Sport Ice Elektro 124
Sport Ice Elektro 124 Operation Manual 2007/4 V2.1 Introduction The Sport Ice Elektro 124 is an ice resurfacing machine designed to be used on small ice surfaces. The machine has been designed to produce
2006 SERVICE AND MAINTENANCE GUIDE
2006 SERVICE AND MAINTENANCE GUIDE VEHICLE IDENTIFICATION Vehicle Identification Number (VIN) Delivery Date Warranty Start Date Mileage at Delivery Model Year Selling Dealer Selling Dealer Phone TABLE
ENTRY-LEVEL AUTOMOTIVE TECHNICIAN
ENTRY-LEVEL AUTOMOTIVE TECHNICIAN Definition: An entry-level automotive technician performs diagnosis and repair to gasoline powered cars and light trucks with limited supervision. The last two bands of
Wynn s Extended Care
Wynn s Extended Care Every car deserves to receive the very best care... especially yours. How Do You Keep Your Reliable Transportation Reliable? Count on Wynn s Because Wynn s has been caring for cars
Service Packages & Pricing
Service Packages & Pricing Silver Gold Motorcycle Service Packages Change oil & filter Change oil & filter Fuel system treatment $ 109.95 $ 129.95 Platinum Replace spark plugs Change oil & filter Fuel
Apprenticeship Training Standard. Truck and Coach Technician. Trade Code: 310T. Development Date: January 2003
Apprenticeship Training Standard Truck and Coach Technician Trade Code: 310T Development Date: January 2003 This document is the property of the apprentice named inside and represents the official record
FORKLIFT SAFETY TIPS
December, 2013 Forklifts are extremely useful workplace vehicles, as long as they are used safely and appropriately by operators who are appropriately trained and competent to use them. Forklifts can be
Sample G1 ASE-type Certification Test. Sample ASE Maintenance and Light Repair (G1)-Type Certification Test
Sample G1 ASE-type Certification Test Sample ASE Maintenance and Light Repair (G1)-Type Certification Test Content Area Questions In Test Percentage Of Test A. Engine Systems 9 16% B. Automatic 4 7% Transmissions
BUYERS GUIDE. IMPORTANT: Spoken promises are difficult to enforce. Ask the dealer to put all promises in writing. Keep this form.
BUYERS GUIDE IMPORTANT: Spoken promises are difficult to enforce. Ask the dealer to put all promises in writing. Keep this form. VEHICLE MAKE MODEL YEAR VIN NUMBER DEALER STOCK NUMBER (Optional) WARRANTIES
Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification
OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product
Maintenance Minder System Reference Guide
Maintenance Minder System Reference Guide PRICE GROUP ACCORD 2006-2009, 4-Cylinder CIVIC 2006-2009 (Includes 2009 GX) CR-V 2007-2009, 2WD ELEMENT 2007-2009, 2WD FIT 2007-2009 PRICE GROUP 2 ACCORD 2006-2009,
ecognition of Prior Learning (RPL)
ecognition of Prior Learning (RPL) ASSESSMENT GUIDE FOR INSPECT AND LUBRICATE AN AUTOMOTIVE SYSTEM Assessment Guide inspect and lubricate an automotive system Page 1 of 9 National Certificate in Professional
Southern Columbia Area School District Bus/Automotive Parts for Sale. PartNo Description Vendor Amount 1 583966C91 EXHAUST CLAMP 1 2 905-09 PIPE 1
Southern Columbia Area School District Bus/Automotive Parts for Sale PartNo Description Vendor Amount 1 583966C91 EXHAUST CLAMP 1 2 905-09 PIPE 1 3 00025296 BACK UP LIGHTS 1 4 00109869 HARNESS Bus Parts
BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > GOKART > BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM) BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Maintaining the Beauty and Performance of Your Boxster
Maintaining the Beauty and Performance of Your Boxster The Porsche Multi-Point Inspection Report The Porsche Multi-Point Inspection Report is completed by our Factory-trained Porsche Technicians every
Oil and Coolant Circulating Heating System. Model - OCSM
Oil and Coolant Circulating Heating System Model - OCSM Installation & Operation Manual 216280-000 REV 2 Identifying Your System The HOTSTART heating system is designed to heat fluids for use in marine
Preventative Maintenance Policies and Plan
Preventative Maintenance Policies and Plan The objectives of the NECTD Preventative Maintenance Policies and Plan are: Ensure that assets are protected and maintained so that they reach their maximum useful
OSHA Regulations 29 CFR 1910.178(I) Powered Industrial Trucks. Mushroom Generic (I) (Sample) Program
OSHA Regulations 29 CFR 1910.178(I) Powered Industrial Trucks Mushroom Generic (I) (Sample) Program March 2012 The following are explanations and instructions on what you need to do to be in compliance
Evaluate, Clean, and Tune Guidance
Evaluate, Clean, and Tune Guidance The Evaluate, Clean and Tune (ECT) process serves three essential purposes in the Weatherization Assistance Program (WAP). The first is to evaluate the existing system
Tranquility. Beyond Protection.
Tranquility. Beyond Protection. unlimited freedom With the Infiniti Elite Extended Protection Plan, there s never a limit to your number of claims on covered repairs INFINITI ELITE EXTENDED PROTECTION
Service and Parts Manual
Service and Parts Manual SPM 629 CST 10/15/20 SERIAL NUMBER ALWAYS GIVE TRUCK SERIAL NUMBER WHEN ORDERING PARTS C RK l!!l Material Company Handling IMPORTANT: Read and understand the contents of this manual
2015 Infiniti Service and Maintenance Guide
2015 Infiniti Service and Maintenance Guide VEHICLE IDENTIFICATION Vehicle Identification Number (VIN) Delivery Date Warranty Start Date Mileage at Delivery Model Year Selling Dealer Selling Dealer Phone
Fire Apparatus Operator Aircraft Rescue and Fire Fighting
Fire Apparatus Operator Aircraft Rescue and Fire Fighting Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/ Operator Professional Qualifications, 2014 Edition. Alabama Fire College
Railgates By THIEMAN IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT.
TVL SERIES Railgates By THIEMAN TVL 20, TVL 30, TVL 20A, TVL 30A OWNERS MANUAL/PARTS LIST! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT.
Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX
Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX Engine (general) Engine code RF Capacity 1998 (cc) Idle speed 725 ± 25 Valve clearance Valve clearance Cold Inlet 0.25 (mm) Exhaust 0.35 (mm) Compression
Warranty & MAINTENANCE GUIDE IT S YOUR RIDE. KNOW WHAT S UP. not to receive these offers.
Experience at (866) 707-2466. please call Scion Customer If the card is no longer attached, updates concerning your vehicle. with important product or safety This will enable Scion to contact you warranty
STATE OF NORTH CAROLINA 3950-3 DEPARTMENT OF ADMINISTRATION MARCH 10, 2010 PURCHASE AND CONTRACT DIVISION NEW ISSUE
STATE OF NORTH CAROLINA 3950-3 DEPARTMENT OF ADMINISTRATION MARCH 10, 2010 PURCHASE AND CONTRACT DIVISION SUPERSEDING NEW ISSUE SPECIFICATION FOR TRUCKS, FORKLIFT, ELECTRIC (This specification is released
FLY SYNTHESIS STORCH HS-CL
STORCH HS-CL MAINTENANCE MANUAL (ALID FOR ROTAX 912 UL AND JABIRU 2200 ENGINES) 00 28/05/07 New manual issue Num. Date Description Issued erify Approvation REISION The FlySynthesis s.r.l. it reserves him
TITAN 13 x 2 ½ BRAKES
INSTALLATION INSTRUCTION AND SERVICE MANUAL Actuator/Trailer Dealer - Please provide these instructions to the consumer. Consumer - Read and follow these instructions. Keep them with the trailer for future
4 Star 4 Star Plus. Vehicle
4 Star 4 Star Plus Vehicle Service Contracts WARRANTY SOLUTIONS Experience you can rely on Throughout our history, Warranty Solutions has demonstrated strength and versatility while evolving through ever-changing
C32 MARINE ENGINE (RXB)
SAFETY.CAT.COM C32 MARINE ENGINE (RXB) Maintenance Intervals Excerpted from Operation & Maintenance Manual (SEBU7908-09) 2009 Caterpillar All Rights Reserved SEBU7908-09 69 Maintenance Interval Schedule
2017 Audi Maintenance Schedule - All Models
2017 Audi Maintenance Schedule - All Models MY 2017 Maintenance Intervals - USA Service Intervals If you are not sure when you should bring your Audi in for service or which services are to be performed
Chapter 7 Hydraulic System Troubleshooting
Chapter 7 Hydraulic System Troubleshooting General The following troubleshooting information is provided as a general guide to identify, locate and correct problems that may be experienced with the hydraulic
Service Manual Rol-Lift
R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing
ENGINE COOLING SYSTEM
ENGINE COOLING SYSTEM 1988 Toyota Celica 1987-88 TOYOTA Engine Cooling Systems Celica DESCRIPTION The basic liquid cooling system consists of a radiator, water pump, thermostat, cooling fan, pressure cap,
ENGINE Dinli 904 D1033-011
ENGINE Dinli 904 D1033-011 ENGINE Model Item Part no Description Specification Quantity 01 E140000-01 E14 ENGINE 450C.C. 1 FENDER SEAT D1033-021 FENDER SEAT Model Item Part no Description Specification
FIRE ENGINE MAINTENANCE PROCEDURE AND RECORD
FIRE ENGINE MAINTENANCE PROCEDURE AND RECORD LICENSE: DUTY STATION: ENGINE IDENTIFICATION NUMBER: -2- FIRE ENGINE MAINTENANCE PROCEDURE AND RECORD PREFACE The Fire Engine Maintenance Procedure and Record
Coastal Community Action Program WSDOT Owned Vehicle Maintenance Plan
Coastal Community Action Program WSDOT Owned Vehicle Maintenance Plan Mission Statement Coastal Community Action Program s (CCAP) vehicle maintenance mission is to effectively and efficiently provide safe,
Meritor WABCO Hydraulic Power Brake (HPB) System Bleeding Procedures
Issued 03-10 Technical Bulletin Meritor WABCO Hydraulic Power Brake (HPB) System Bleeding Procedures Issued 1 Technical 03-10 Bulletin Hazard Alert Messages Read and observe all Warning and Caution hazard
2010 SERVICE AND MAINTENANCE GUIDE
2010 SERVICE AND MAINTENANCE GUIDE VEHICLE IDENTIFICATION Vehicle Identification Number (VIN) Delivery Date Warranty Start Date Mileage at Delivery Model Year Selling Selling Phone TABLE OF CONTENTS OWNER
Maintaining the Beauty and Performance of Your 911
Maintaining the Beauty and Performance of Your 911 The Porsche Multi-Point Inspection Report The Porsche Multi-Point Inspection Report is completed by our Factory-trained Porsche Technicians every time
1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43
DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496
Cooling system components, removing and installing
Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,
Cooling system components
Page 1 / 33 19-1 Cooling system components Caution! When doing any repair work, especially in the engine compartment, pay attention to the following due to clearance issues: Route lines of all types (e.g.
Fire Apparatus Operator: Pre-Course Driving Skills
Fire Apparatus Operator: Pre-Course Driving Skills Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/Operator Professional Qualifications, 2014 Edition. Alabama Fire College August
NATIONAL CERTIFICATE (VOCATIONAL)
NATIONAL CERTIFICATE (VOCATIONAL) SUBJECT GUIDELINES AUTOMOTIVE REPAIR AND MAINTENANCE NQF LEVEL 3 Implementation: January 2014 INTRODUCTION A. What is Automotive Repair and Maintenance Level 3 about?
Trouble Shooting. Pump
Trouble Shooting Pump Trouble Possible Cause Remedy Oil leaking in the area of water pump crankshaft Worn crankshaft seal, bad bearing, grooved shaft, or failure of retainer o-ring. Excessive play on crankshaft
Extended Coverage Customer Personal Service
Extended Coverage Customer Personal Service www.johndeere.com At John Deere, feeling secure is not an option Standard warranty promises that on construction machines under 100 horsepower, we ll fix all
1/29/2008 DR50. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45
DR50 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR50-001 842645074424 CYLINDER 1 1 2 DR50-002 842645074431
Rail 001 112 2 Canvas, folding top 001 101 3 Rear panel 001 102 4 Stip in window, left 001 106 dto. right 001 107
U 411 1 Rear view mirror, round, metall 13cm Ø 002 045 2 Raised airintake 002 060 3 Side panelling, front, left 002 030 Side panelling, front, right 002 031 4 Panelling left 002 051 dto. right 002 052
EXCAVATOR SAFETY TRAINING
EXCAVATOR SAFETY TRAINING INSPECTION CHECKLIST INSPECTION AREA INSPECTION RESULTS Sat. Unsat. N/A Comments Carrier & Car Body Rotation system Tracks Rollers Frame, welds, bolts Drive system Upper Structure
Turbocharger system components, servicing
21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners
STEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
Customer Support Agreements
Cleveland Brothers Product Support Customer Support Agreements Maximize Uptime Minimize Risk Insulate Prices Increase Profitability Let a CSA go to WORK for your company CUSTOMER SUPPORT AGREEMENTS A CSA
Selecting the proper maintenance schedule. Service precautions. Maintenance
Maintenance Service precautions Vehicle maintenance is an important yet frequently neglected item. Proper maintenance will aid in retaining the level of performance that has been engineered into your Mitsubishi
Cylinder head gasket, replacement
"VCC065612 EN 20110604" 1(7) Cylinder head gasket, replacement Special tools: 999 5098 Disconnect battery earth lead Drain coolant Remove heat shield over exhaust manifold. (Only the two bottom bolts on
OPERATOR S MANUAL WARNING
ELECTRIC PALLET TRUCK E30 SERIES OPERATOR S MANUAL WARNING DO NOT INSTALL, OPERATE OR SERVICE THIS PRODUCT UNLESS YOU HAVE READ AND FULLY UNDERSTAND THE ENTIRE CONTENTS OF THIS MANUAL. FAILURE TO DO SO
Work Order History Report
Work Order History Report Asset MG304 Asset: MG304, Including Children, Active: True Grader, motor W/O No Description Finished Done 1570 MG304 - Perform Plant Audit and Mobile Plant Mechanical Check List.