8ETH06 8ETH06S 8ETH06-1 8ETH06FP

Transcription

1 8ETH06 8ETH06S 8ETH06-8ETH06FP Hyperfast Rectifier Features Hyperfast Recovery Time Low Forward Voltage Drop Low Leakage Current 75 C Operating Junction Temperature 500V insulation voltage UL E78996 approved t rr = 8ns typ. I F(AV) = 8Amp V R = 600V Description/ Applications State of the art Hyperfast recovery rectifiers designed with optimized performance of forward voltage drop, Hyperfast recover time, and soft recovery. The planar structure and the platinum doped life time control guarantee the best overall performance, ruggedness and reliability characteristics. These devices are intended for use in PFC Boost stage in the AC-DC section of SMPS, inverters or as freewheeling diodes. The IR extremely optimized stored charge and low recovery current minimize the switching losses and reduce over dissipation in the switching element and snubbers. Absolute Maximum Ratings Parameters Max Units V RRM Peak Repetitive Reverse Voltage 600 V I F(AV) Average Rectified Forward Current@ T C = 44 C 8 T C = 8 C (FULLPACK) I FSM Non Repetitive Peak Surge T J = 5 C 90 (FULLPACK) 0 I FM Peak Repetitive Forward Current 6 T J, T STG Operating Junction and Storage Temperatures - 65 to 75 C Case Styles 8ETH06 8ETH06S 8ETH06-8ETH06FP Base Cathode Base Cathode 3 Cathode Anode TO-0AC N/C 3 Anode D PAK N/C 3 Anode TO-6 3 Cathode Anode TO-0 FULLPACK

2 Electrical T J = 5 C (unless otherwise specified) Parameters Min Typ Max Units Test Conditions V BR, V r Breakdown Voltage, V I R = 0μA Blocking Voltage V F Forward Voltage V I F = 8A, T J = 5 C V I F = 8A, T J = 50 C I R Reverse Leakage Current μa V R = V R Rated μa T J = 50 C, V R = V R Rated C T Junction Capacitance pf V R = 600V L S Series Inductance nh Measured lead to lead 5mm from package body Dynamic Recovery T C = 5 C (unless otherwise specified) Parameters Min Typ Max Units Test Conditions t rr Reverse Recovery Time - 8 ns I F = A, di F /dt = 0A/μs, V R = 30V I F = 8A, di F /dt = 0A/μs, V R = 30V T J = 5 C T J = 5 C I RRM Peak Recovery Current A T J = 5 C T J = 5 C I F = 8A di F /dt = 00A/μs V R = 390V Q rr Reverse Recovery Charge nc T J = 5 C T J = 5 C t rr Reverse Recovery Time ns I RRM Peak Recovery Current - - A T J = 5 C Q rr Reverse Recovery Charge nc I F = 8A di F /dt = 600A/μs V R = 390V Thermal - Mechanical Characteristics Parameters Min Typ Max Units T J Max. Junction Temperature Range C T Stg Max. Storage Temperature Range R thjc Thermal Resistance, Junction to Case Per Leg -.4 C/W (Fullpack) Per Leg R thja Thermal Resistance, Junction to Ambient Per Leg R thcs Thermal Resistance, Case to Heatsink Weight g (oz) Mounting Torque Kg-cm lbf.in Typical Socket Mount Mounting Surface, Flat, Smooth and Greased

3 Instantaneous Forward Current - I F (A) 0 T = 75 C J T = 50 C J T = 5 C J Reverse Current - I R (μa) Junction Capacitance - C T (pf) T J = 75 C 50 C 5 C 0 C 5 C Reverse Voltage - V R (V) Fig. - Typical Values Of Reverse Current Vs. Reverse Voltage 00 T J = 5 C Forward Voltage Drop - V FM (V) Fig. - Typical Forward Voltage Drop Characteristics Reverse Voltage - V R (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage Thermal Impedance Z thjc ( C/W) 0. D = 0.50 D = 0.0 D = 0. D = 0.05 D = 0.0 D = 0.0 Single Pulse (Thermal Resistance). Peak Tj = Pdm x ZthJC + Tc t, Rectangular Pulse Duration (Seconds) Fig. 4 - Max. Thermal Impedance Z Characteristics thjc P DM t t Notes:. Duty factor D = t/ t 3

4 Allowable Case Temperature ( C) Thermal Impedance Z thjc ( C/W) D = 0.50 D = 0.0 D = 0. D = 0.05 D = 0.0 P DM D = 0.0 t 0. Single Pulse t (Thermal Resistance) Notes:. Duty factor D = t/ t. Peak Tj = Pdm x ZthJC + Tc Square wave (D = 0.50) Rated Vr applied t, Rectangular Pulse Duration (Seconds) Fig. 5 - Max. Thermal Impedance Z thjc Characteristics (FULLPACK) 80 Square wave (D = 0.50) Rated Vr applied 60 see note (3) DC 30 see note (3) Average Forward Current - IF (AV) (A) Fig. 6 - Max. Allowable Case Temperature Vs. Average Forward Current Allowable Case Temperature ( C) DC Average Forward Current - IF (A) (AV) Fig. 7 - Max. Allowable Case Temperature Vs. Average Forward Current (FULLPACK) Average Power Loss ( Watts ) RMS Limit D = 0.0 D = 0.0 D = 0.05 D = 0. D = 0. D = 0.5 DC Average Forward Current - IF (AV) (A) Fig. 8 - Forward Power Loss Characteristics (3) Formula used: T C = T J - (Pd + Pd REV ) x R thjc ; Pd = Forward Power Loss = I F(AV) x V (I F(AV) / D) (see Fig. 8); Pd REV = Inverse Power Loss = V R x I R ( - D); I V R = rated V R 4

5 60 IF = 6 A IF = 8 A V R= 390V T J = 5 C T J = 5 C IF = 6 A IF = 8 A trr ( ns ) 30 Qrr ( nc ) V R = 390V T J = 5 C T J = 5 C 0 00 di F /dt (A/μs ) Fig. 9 - Typical Reverse Recovery vs. di F /dt di F /dt (A/μs ) Fig. - Typical Stored Charge vs. di F /dt Reverse Recovery Circuit V R = 00V 0.0 Ω di F /dt dif/dt ADJUST L = 70µH G D IRFP50 D.U.T. S Fig. - Reverse Recovery Parameter Test Circuit 5

6 3 0 I F t a trr t b Q rr 4 I RRM 0.5 I RRM di(rec)m/dt I RRM di F f /dt. di F /dt - Rate of change of current through zero crossing. I RRM - Peak reverse recovery current 3. t rr - Reverse recovery time measured from zero crossing point of negative going I F to point where a line passing through 0.75 I RRM and 0.50 I RRM extrapolated to zero current 4. Q rr - Area under curve defined by t rr and I RRM Q rr = t rr x I RRM 5. di (rec) M / dt - Peak rate of change of current during t b portion of t rr Fig. - Reverse Recovery Waveform and Definitions Outline Table Conforms to JEDEC Outline TO-0AC Dimensions in millimeters and (inches) 6

7 Outline Table Conforms to JEDEC Outline D PAK Dimensions in millimeters and (inches) Conforms to JEDEC Outline TO-6 Dimensions in millimeters and (inches) 7

8 ETH06, 8ETH06S, 8ETH06-, 8ETH06FP Outline Table.6.4 HOLE ø Cathode Anode.54 TYP TYP TYP.05 R0.7 ( PLACES) R0.5 5 ± ± 0.5 Conforms to JEDEC Outline TO-0 FULLPACK Dimensions in millimeters and (inches) Tape & Reel Information Dimensions in millimeters and (inches) 8

9 Part Marking Information EXAMPLE: TO-0AC THIS IS A 8ETH06 LOT CODE 789 ASSEMBLED ON WW 9, 00 IN THE ASSEMBLY LINE "C" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER DATE CODE YEAR = 00 WEEK 9 LINE C D PAK THIS IS A 8ETH06S LOT CODE 804 ASSEMBLED ON WW 0, 000 IN THE ASSEMBLY LINE "L" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER DATE CODE YEAR 0 = 000 WEEK 0 LINE L EXAMPLE: TO-6 THIS IS A 8ETH06- LOT CODE 789 ASSEMBLED ON WW 9, 999 IN THE ASSEMBLY LINE "C" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER DATE CODE YEAR 9 = 999 WEEK 9 LINE C FULLPACK EXAMPLE: THIS IS A 8ETH06FP LOT CODE 789 ASSEMBLED ON WW 9, 000 IN THE ASSEMBLY LINE "C" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER DATE CODE YEAR 0 = 000 WEEK 9 LINE C 9

10 Ordering Information Table Device Code 8 E T H 06 - TRL Current Rating (8 = 8A) - E = Single Diode 3 - T = TO H = HyperFast Recovery 5 - Voltage Rating (06 = 600V) 6 - None = TO-0 S = D Pak - = TO-6 Option FP = TO-0 FULLPACK 7 - None = Tube (50 pieces) TRL = Tape & Reel (Left Oriented - for D Pak only) TRR = Tape & Reel (Right Oriented - for D Pak only) 8 - none = Standard Production PbF = Lead-Free Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 33 Kansas St., El Segundo, California 9045, USA Tel: (3) 5-75 TAC Fax: (3) Visit us at for sales contact information. 09/06