Wireless zone control thermostat

Transcription

1 User Manual del WCZ-600-T Wireless zone control thermostat The WCZ-600-T wireless thermostat is one of up to six thermostats that has been installed as part of the WCZ-600 Wireless Comfort zone control system. Each thermostat communicates with the WCZ-600 zone control panel which controls the heating, cooling and ventilation system while directing the right amount of conditioned air into each zone through wireless communications with zone dampers that open and close to maintain the desired temperature setting in each zone. Each WCZ-600-T thermostat allows you to set separate separate temperatures for heating and cooling for four time periods per day (morning, daytime, evening and night). Or, you can operate each thermostat without using the schedule feature (Permanent Hold de). Energy Savings The schedule feature can save energy by reducing heating and cooling when a zone is not being occupied. SYSTEM FAN Indicates rn,, Eve or Night schedule Temperature Setting Up and Down keys used when adjusting temperature, time of day, day of the week, program start times and other options Space temperature Indicates the, Hold or Permanent Hold mode SYSTEM FAN SYSTEM key selects, Cool, Auto /Cool, Off and Emergency ing for a heat pump application Menu key used to set time of day, daily schedule, calibrate temperature sensor and display schedule. Fan key selects Auto or Cont fan operation Hold key used to switch between and Permanent H operation Next key used when setting time of day and schedules Battery compartment, 2 AA batteries. Enter key used when setting time of day and schedules

2 Factory This thermostat is shiped from the factory with the following programmable schedule. Program rning Evening Night Start Time 6:00 8:00 5:00PM 10:00PM ing 70F 62F 70F 62F Setpoint Cooling 78F 82F 78F 82F Warning! The thermostat relies on battery power for communications with the WCZ-600 zone control panel. Change the batteries every year or whenever the low battery warning is displayed. Selecting System Off, Auto,, Cool or EM HT Press the System key to select Off, Auto (heating and cooling) (heating), Cool (cooling) or EM HT (emergency heating if your system is a heat pump). In Auto, the thermostat will call for heating or cooling based on the heating and cooling set temperatures and the indoor temperature. To view both the heating and cooling set temperature in Auto mode, press the key. The LCD will display and then Cool along with the corresponding set temperature. Use the UP and DOWN keys to change the set temperature when the proper mode is displayed. HEAT System de Selecting Fan Auto or Cont Press the Fan key to select Auto or Cont (continuous) fan operation. In Auto the thermostat activates the fan during heating and cooling calls. In Cont the fan runs continuously to circulate air. Fan de HEAT Th 2

3 Selecting or Permanent Hold Press the Hold key to switch between Hold, Hold Permanent and. operation automatically changes the heating and cooling temperature settings at the four scheduled times ( rning,, Evening and Night). When in operation, adjusting the heating or cooling temperature using the Up and Down keys will switch the thermostat to the Hold mode. After 3 hours the thermostat will return to the mode or you can press the Hold key at any time to switch to the mode. The Hold Permanent mode maintains the heating and cooling temperatures indefinitely until the Hold key is pressed which will return the thermostat to the mode. HEAT de in Key Setting the ing and Cooling Temperature Press the UP and Down key to change the heating or cooling temperature. Press the Next key to switch between the heating and cooling temperature. Cool HEAT de in Th Key 3

4 Setting the Time and To set the time of day and the day of the week, press the key and the LCD will display the hour. Use the Up and Down keys to set the hour. Make sure that the or PM is correct. Press the key to set the minute. Use the Up and Down keys to set the minute. Press the key to set the current day of the week. Use the Up and Down keys to select the day of the week and press the key. Changing the Press the key twice until the LCD displays the schedule screen shown below with the current day of the week. Press and hold the UP or Down key to change the morning ( rn) schedule start time. The start time is in 15 minute increments. Make sure that the or PM is correct. rn Press the key to display the morning heating () temperature. Use the Up and Down keys to change the temperature. rn Th 4

5 Press the key to display the morning Cooling (Cool) temperature. Use the Up and Down keys to change the temperature. Cool rn Continue using the key and the Up and Down keys to set the start time, heating temperature and cooling temperature for the, Evening and Night schedules. After the Night schedule is completed, you can press the key which will only save the schedule for the current day or you can apply the same schedule to other days of the week by pressing the key. Night PM Each time you press the key an additional day will be added to the schedule. Use the Up and Down keys to turn any day off that you don t want as part of the schedule. Only the days displayed on the thermostat will be copied to the schedule when you press the key. As an example, you might want one schedule for the days of the week and a separate schedule for the weekend. TuWe Th Fr Night PM After pressing the key the thermostat will return to normal operation. To change the schedule for other days of the week, repeat the same programming steps. Each day of the week can have a separate schedule if required. Just program the schedule, select the day then press the key. 5

6 Reviewing the Time and Temperature Press the key 5 times until the first schedule is displayed as shown below. The display will show the nday morning schedule start time and heating temperature. rn Continue pressing the key to display the morning, day, evening and night schedule along with the heating and cooling temperatures for each day of the week. Press the key at any time to exit and return the thermostat to normal operation. Vacation de If you plan to leave for an extended period of time and want to save energy by placing your Comfort System in Permanent Hold, it is not necessary to change all the thermostats in the zoning system. The zone thermostat that has been assigned Zone Number 01 is the only thermostat in the system that can be set for Vacation de. If you are unsure which thermostat is Zone 01, there should be a label located on the subbase of each thermostat identifying its zone number. Simply release the thermostat from its subbase by pressing up from the bottom center and swinging it away. he thermostat identification label is located in the lower left hand corner. If the installing contractor did not fill out the identification label, you can find the thermostat zone address by accessing the thermostat Installer Options menu. FILL OUT AND AFFIX TO LOWER LEFT HAND CORNER OF THERMOSTAT SUBBASE Thermostat Zone # Thermostat Home # Location 1 1 Living Room ZONE NUMBER 6

7 Caution! Do not make any changes to the Installer Options or your Wireless Comfort thermostat may fail to operate properly. To access the thermostat Installer Options menu, press and hold the key for approximately 5 seconds or until the following appears on the display. If Option 01, Zone 01 appears, this is the correct thermostat. To exit the menu, press the key. Zone O1 Option O1 To select Vacation de, press the key 3 times until the following appears on the display. Zone One Controlling OFF In normal operation, the Vacation de is OFF. To turn it on, press the UP and DOWN keys until the word On is displayed and then press the key. Zone One Controlling O The thermostat will now display Zone One Controlling On. You can place the thermostat in Permanent Hold and then set unoccupied heating and/or cooling temperatures. The zone one thermostat now becomes the master control and all other zone thermostats are disabled. When the thermostat calls for heating or cooling, all zones will receive conditioned air. If the thermostat is set in the Continuous Fan mode, all zones will receive ventilation air. Upon return from an extended leave, the Vacation de must be turned off in order for all other zone thermostats to have individual control. Remember to take the thermostat out of Permanent Hold if you want it to resume a pre-programmed schedule. Simply press the key until the thermostat displays. 7

8 Low Battery Indication If the battery voltage drops to where it could interfere with reliable operation, the thermostat LCD will alternately display Lo in place of the room temperature. Replace batteries immediately. It will be necessary to reset the time of day and the day of the week after changing the batteries but the schedule will not be affected as it is saved in non-volitile memory. Th Even if communications is lost with every thermostat in your Wireless Comfort zoning system, the zone control panel will still be able to operate the HVAC system to maintain a preset heating and cooling temperature as selected by your installing contractor to prevent freezing or overheating of all zones. Temperature Calibration Your Wireless Comfort thermostats have been accurately calibrated at the factory. However, if the inside temperature displayed on the LCD requires re-calibrating, press the key 4 times until only the inside temperature is displayed on the LCD. Use the Up and Down keys to change the inside temperature in 1 degree increments. Caution: Re-calibrating the inside temperature display requires the use of a highly accurate digital thermometer. Therefore, it is recommended that you contact your heating and air conditioning contractor in the event re-calibration is required. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation Elmwood Avenue, Indianapolis, IN All rights reserved. Jackson Systems, LLC 2010 Intellectual rights apply