Tele Greenland User Interface Manual Advanced

Transcription

1 Tele Greenland User Interface Manual Advanced

2 Configuring your local network The default local IP address of your home gateway is Your connected hardware items will have an IP address in the range to If you want to change your local network s addressing plan, select the "LAN" menu under the "Router" heading. Securing your Internet access Note: You can access the firewall configuration only if you are in the Administrator mode. Your home gateway has a firewall with 4 levels of security: None: the firewall is deactivated Normal: the firewall filters incoming packets according to NAT rules. This is the default mode. Maximum: the firewall filters incoming and outgoing packets Custom: the firewall lets you define the rules: Enter an application name Enter the IP address and the source port of the IP packet to filter Enter the IP address and the destination port of the IP packet to filter Define the action type as accepted (green arrow) or refused (red arrow)

3 Authorizing programs to access the Internet Your home gateway contains a firewall that blocks any communication initiated from outside network. This function may affect some applications behaviour: - Online games - Communication tools ( , video conferencing, etc.) - Server applications (FTP, SMTP) To allow some of your applications to pass through the firewall: Select the "Applications" menu in the "Box" tab Select the applications you require from the drop-down menus Click OK to confirm Configuring the NAT Note: You can configure a NAT rule only if you are in the Administrator mode. The forwarding table allows all the packets received via a specific port to be transmitted to a specific machine on the internal network. Therefore, if you want to be able to access a web server operating on machine from outside, you will have to define a forwarding rule that redirects all the TCP packets received via port 80 to another defined port on machine To configure a NAT rule: Indicate an application name Select the protocol type: TCP or UDP Enter the port that has to be forwarded to the internal service Indicate the address of the hardware on the local network, followed by the destination port. The request will be forwarded to this private address

4 Defining a DMZ Note: You can set up a DMZ only if you are in the Administrator mode. The DMZ enables you to show a machine on the Internet with no restriction on the ports used. It allows you to open all previously undefined ports (port forwarding) to a single LAN machine: Click "Enabled" to enable the service Enter the IP address of the machine that will be in the DMZ, aka Click OK to confirm Activating UPnP The UPnP IGD feature allows some applications to configure the NAT automatically.

5 Saving and restoring settings Note: You can back up and restore your settings only if you are in the Administrator mode. To save your settings, click "Back up your Parameters". Select your file s location on your computer and confirm. To restore the settings, select the file path to the previously saved file and click "Restore".

6 HOME GATEWAY LEDS BEHAVIOURS LED COLOUR DESCRIPTION POWER OFF Power Off (Power supply not plugged or I/0 switch off on the rear panel) AMBER Firmware update is on- going. RED CPE boot failure. Failure due to internal sequence or state that will prevent the device from connecting to the access network or passing customer data. GREEN The device is powered on (power supplied and I/0 switched on the rear panel). ETHERNET OFF No Ethernet device connected on the LAN. SOLID GREEN One Ethernet device connected and no traffic is passing through the CPE. FLASHING GREEN One Ethernet device connected and traffic is passing through the CPE (either direction). WIRELESS OFF Wi- Fi is disabled. (Option unchecked in the UI). GREEN Wi- Fi is enabled (Option checked in the UI) which is the default behavior. A wireless device can be connected. WPS OFF WPS is disabled. (Option is unchecked in the UI). SOLID GREEN WPS is enabled (option is checked in the UI) which is the default behavior. FLASHING GREEN WPS button is pushed on. Pairing process is on- going for 120 seconds. A wireless device can be paired. After 120s the WPS Led becomes solid green. PHONE 1 OFF No VoIP account set up. or Registration to the softswitch failed. SOLID GREEN The VoIP account number one is set up and registered to the softswitch. FLASHING GREEN Phone call is on- going. PHONE 2 OFF No VoIP account set up. or Registration to the softswitch failed. SOLID GREEN The VoIP account number two is set up and registered to the softswitch. FLASHING GREEN Phone call is on- going. 3G OFF No 3G USB key plugged in the CPE. SOLID GREEN A 3G USB key is plugged in and detected by the CPE. The CPE has a 3G WAN IP address. BROADBAND OFF Broadband interface powered off, no signal detected. SOLID GREEN Broadband physical connection is established (e.g. DSL sync). FLASHING GREEN Signal detected, in process of synchronizing. INTERNET OFF Broadband physical interface connection not present. RED Device attempted to become IP connected and failed (DHCP, PPPoE, PPPoA, etc.). SOLID GREEN The CPE has a WAN IP address and there is no activity on the WAN. FLASHING GREEN The CPE has a WAIN IP address and there is activity on the WAN.

7 HOME NETWORK CONFIGURATION Displaying the devices connected to your home gateway Using the "Connected Equipment" function under the Home Network heading, you can: Display the devices detected by your home gateway: computers connected via Ethernet or WiFi, USB accessories (webcam, 3G dongle, hard disk, etc.) Find the IP address, i.e. the unique connection address for these devices Sharing your printer Note: You can share a printer only if you are in the Administrator mode. The Printer function under the Home Network heading allows you to share a printer between all the computers connected to your home gateway. This service is compliant with printers that have a USB connector. Scanners and multifunction printers are not supported. Only one printer may be connected at a time.

8 Sharing your home center In order to access in the content of sharing devices, an authentication is required with the credentials admin/admin by default. When access is granted, a web page of home center appears and user can access to 4 menus: - My Files - My Music - My Pictures - My Cameras When user selects on My Files menu, all files will appear in front of user, who can make all operations on files, as: - Drag & drop - Delete - Modify the name

9 The same operations are available also for My Music menu as for My Files menu, and user can launch the music playlist, by clicking on the Play button: About pictures, all pictures can be shown like a slideshow, just by using left and right scroll arrows, after clicking on one picture. About camera, if one USB camera is connected, it s possible to use all camera functions as usual.

10 Diagnosing your home gateway status SUPPORT The "Box Diagnostics" function under the "Troubleshooting" heading lets your display your home gateway s characteristics, the status of the internet connection and the interfaces. Diagnosing the ASDL line status The "ADSL Statistics" function under the "Troubleshooting" heading lets you display technical information about your ADSL line. If the current status is "Idle": Check that your home gateway is properly connected to the telephone socket, If this does not solve the problem, check with your Internet service provider that your ADSL line has been properly activated. Restarting your home gateway Note: You can access the Restart function only if you are in the Administrator mode. You can restart your home gateway using the Restart function under the "Management heading. Your settings will be saved.