UNDERHOIST STAND WITH FOOT PEDAL ASSEMBLY & OPERATING INSTRUCTIONS

Transcription

1 UNDERHOIST STAND WITH FOOT PEDAL ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA Visit our Web Site at Copyright 2004 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts please call

2 THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner s record below: Model Serial No. Purchase Date SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Maximum Capacity: 1,650 Lbs. Height Range: 55" to 81-1/2" Lift: 26-1/2" Base: 11-3/4" diameter x 3/16" Overall Dimensions: 21" long x 12" O.D. x 58-1/2" Height Weight: 35 Lbs. Spin handle with thrust bearing for quick adjustments, all steel contruction. Foot pedal for fine workload adjustments. General usage: This Underhoist Stand with Foot Pedal can be used to adjust vehicle transmissions and mufflers that are secured inside an already supported vehicle. Safety Warnings and Precautions WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! 1. Keep work area clean. Cluttered areas invite injuries. 2. Observe work area conditions. Keep work area well lighted. 3. Store idle equipment. When not in use, the Underhoist Stand must be stored in a dry location to inhibit rust. Always lock up products and keep out of reach of children. 4. Use the right product for the job. There are certain applications for which the Underhoist Stand was designed. It will do the job better and more safely supporting a load for which it was intended. Do not modify the Underhoist Stand and do not use the Underhoist for a purpose for which it was not intended. 5. Check for damaged parts. Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. SKU For technical questions please call Page 2

3 6. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. 7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the product. 8. Use eye protection. Always wear ANSI approved impact safety goggles. 9. Do not exceed this product s maximum load capacity of 1,650 Lbs. 10. Make certain that the load is fully centered on the saddle. 11. The part being adjusted must be securely supported through other means such as chains, straps and hoists. The Underhoist Stand is not designed to solely support heavy components. 12. Make certain to place the Underhoist Stand on a dry, clean, solid level surface capable of supporting the Underhoist Stand, the vehicle and parts being hoisted, and the initial source of secure support for the vehicle parts. 13. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened. 14. When using the Underhoist Stand, whenever possible, keep personnel clear of the area under the item being adjusted. 15. Not to be used for aircraft purposes. 16. Failure to heed all instructions and warnings may result in death, personal injury, and /or property damage. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Underhoist Stand with Foot Pedal, check to make sure the following parts are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at Assembly Your Underhoist Stand will require complete assembly prior to use. It is important that you read the entire manual to become familiar with the product BEFORE you assemble and use the Underhoist Stand. Before assembling and operating the Underhoist Stand be sure that you have all parts described in the Parts List and Assembly Diagram located on the last pages of this manual. 1. Thread the Holder (19) into the Base (21). 2. Thread the Handle (3) into the Metal Support (6). 3. Screw the Threaded Post (7) down into the the Metal Support (6). Continue to screw the Threaded Post (7) down until most of the Threaded Post (7) is down inside the Metal Support-see Figure Thread the Saddle (1) onto the top of the Threaded Post (7)-see Figure 1 and Figure Screw in Lock Pin (2) to secure the Saddle (1) in place-see Figure 2. SKU For technical questions please call Page 3

4 Figure 1 Figure 2 Saddle (1) Saddle (1) Threaded Post (7) Lock Pin (2) Handle (3) Metal Support (6) 6. Thread the Holder (19) down into the Base (21)-see Figure Set the Metal Support (6) down into the Holder (19). Insert Stop Pin (16) through Washer (20) and insert it through the Holder (19) and Metal Support (6). Slide on second Washer (20). Secure the Stop Pin in Place with Retaining Pin (18)-see Figure 3. Figure 3 Metal Support (6) Foot Pedal (14) leg Holder (19) Stop Pin (16) Washer (20) Retaining Pin (18) Retaining Pin (18) Stop Pin (15) Washer (20) 8. Set the leg of the Foot Pedal (14) into the slot between the bars on the Holder (19). Slide a Washer (20) onto the Stop Pin (15). Slide the Stop Pin (15) through the bar, the Foot Pedal leg and through the outside bar. Slide on second Washer (20). Thread on Retaining Pin (18). Operation 1. Make certain that the automotive part that you are working on is fully supported by chains, straps and hoists. The Underhoist Stand is not designed to solely support heavy components. 2. Set the Underhoist under the load to be worked on. Turn the Handle (3) counterclockwise to raise and clockwise to lower the Saddle (1) of the Underhoist. 3. Set the Underhoist under the appropriate lifting points as indicated by the vehicle s owner s manual. Center the load on the Saddle (1) and continue to turn the Handle (3) to bring the Saddle (1) into full contact with the load to be supported. 4. Use the Foot Pedal (14) to jiggle the Saddle (1) while making minor adjustments to the load. This is the only purpose of this Underhoist Stand. Never attempt to use the Underhoist Stand to support a load. 5. Reverse the order of steps one through five to lower the Underhoist. Make certain that at all times the load is fully supported by other means than the Underhoist Stand. SKU For technical questions please call Page 4

5 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Parts List Part # Description Quantity Part # Description Quantity 1 Saddle 1 15 Stop Pin 1 2 Lock Pin 1 16 Stop Pin 1 3 Handle 1 17 Retaining Pin 1 4 Bearing Retainer 2 18 Retaining Pin 1 5 Ball Bearings 1 19 Holder 1 6 Metal Support 1 20 Washer 4 7 Threaded Post 1 21 Base 1 14 Foot Pedal 1 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Assembly and Parts Diagram SKU For technical questions please call Page 5