General Technical Specification for A1 Room-Modules with fixed walls

Transcription

1 General Technical Specification for A1 Room-Modules with fixed walls General remarks: The following description refers to the specification and furnishing of standard types. A1 Room-Modules match ISO dimensions and have the advantages of this norm system. Construction is based on a stable frame with fix walls. The individual modules can be stood either side-by-side or stacked on top of each other. Individual sizes of space can be achieved by removing outer fix walls and fitting of partitions. standard measurements and weights of A1 Room-Modules container type internal dimensions [mm] external dimensions [mm] length width height length width height weights [kg] RM RM RM RM RM stud 2.5 m stud 2.6 m A1 Room-Modules can also be delivered in dimensions which are exactly adapted to the individual use or to the available space. SPECIFICATION DETAILS page 1/5

2 1.) BASE floor: chipboard, water resistant (V100), free of formaldehyde (E1); 1.5 mm synthetic floor covering (flash point class B1 - difficult to burn, smoke density Q1), welded seams; water soluble adhesive, environment friendly. In sanitary modules, the synthetic floor covering is laid to floor and approx. 100 mm up each wall all seams being welded. Additional strengthening is provided in the area where the boiler is positioned. floor base: mm galvanised sheet metal load bearing capacity: 2-5 kn/m² self supporting isolation: mm mineral-wool slabs, flash point class A not flammable; smoke density class Q1-low smoke emission, in accordance with ÖNORM B 800) k-value: W/m²K. 2.) ROOF CEE connection: sunken in frontal roof frame roof covering: 0.6 mm galvanised sheet metal, double folded along whole module length load bearing capacity: kn/m² roof covering/interior: chipboard overlaid both sides, free of formaldehyde (E1) isolation: mm mineral-wool slabs k-value: W/m²K.) CORNER POSTS construction: self supporting steel frame construction consisting of cold rolled steel profile, 8pcs welded container posts which are correlating with ISO norm (not to be used for Twistlock fortification) fitting: corner posts are welded together with base and roof frame isolation: to avoid cold bridges, the corner posts are isolated with mineralwool slabs water drainage: rainwater will be drained through four seamless PVC-down pipes which are fitted into the corner posts, 50 mm page 2/5

3 .) FIX WALL exterior cladding: profiled galvanised sheet metal, PVC overlaid, 0.6 mm interior cladding: plastic coated chipboard, V20, free of formaldehyde (E1), thickness = 10 mm, inside decor: white or light oak isolation: mm mineral wool slabs k-value: W/m²K ground floor beam inside wall 2 ground floor isolation 5 roof beam fix wall 6 roof isolation 1 page /5

4 1 2 1 corner post fix wall 2 rainwater pipe inside wall 5.) SURFACE PRESERVATION All steel profiles will be fully abrasive shot blasted and coated with a primer prior to assembling, all sheet metals will be hot-dipping zinc galvanised. 6.) PAINTING/COATING primer coating: epoxyprimer ca. 20 μm top coating: vinylacryl ca. 110 μm All zinc galvanised sheet metals are PVC overlaid in standard colours. 7.) ELECTRICAL INSTALLATION Electric cabling is concealed and in sanitary modules in moisture resistant specification. All parts fulfil ÖVE/VDE norms, also other European norms can be supplied. technical data: voltage 220/00 V, 50 Hz exterior: connection supplying according to CEE-Norm (= Commission Electrotechnique Europeenne) sunken in the roof frame, or 5 pole/2a or 16A socket and plug earthing: 1 galvanised strip iron earth electrode (25 x mm) It is the responsibility of the buyer/lessee to arrange for the earthing installation on site. page /5

5 8.) WATER INSTALLATION cold water supply: polypropylene pipe fed through the fix wall, nominal pressure max.10 bar, proof pressure 15 bar sewage: collected in plastic pipes (50 mm to 100 mm diameter) for discharge through the fix wall into an authorised sewage network in accordance with local regulations governing disposal of waste water hot water supply: by electric boiler - size subject to use: 5 l, 80 l, 150 l or 00 litre capacity IMPORTANT: Tanks are designed for a working pressure of max. 6 bar. Higher water pressures will demand the fitting of a pressure reduction valve. 9.) HEATING AND VENTILATION (optional) Heating by thermostatically controlled and/or temperature controlled electric radiators or electric fan heaters. Mechanical air circulation via electric ventilators. Air conditioning can be supplied if required. Regular ventilation of the rooms has to be provided - a relative humidity of 70 % should not be exceeded. 10.) SITING AND ERECTION Any individual module should always be mounted on either wooden or concrete foundation bearers (6 bearers). The same applies to the combining of several A1 Room- Modules in a cluster where units must be positioned over concrete bearers or concrete slabs. Foundation parameters and frost depths would be subject to local demands and soil conditions. Pay attention to enough air ventilation of the floor room under the container compound. Water drainage is necessary, to avoid still standing water for container compounds which consist of more than pcs of containers. Level foundations are necessary for problem-free positioning and friction-free erection of any combination. For assembling please read the appropriate assembling manual. 11.) HANDLING With overhead rope, 60 ( corners), forklift, container-lift. technical alterations reserved A1 Container International GmbH. page 5/5