6ZOZ USER'S MANUAL. 3. Support Modem Ring-On (COM A and COM B). 4. Support 3 steps ACPI LED. 5. ATi 3D RAGE PRO graphics acceleration Onboard.

Transcription

1 USER'S MANUAL. System power on by PS/ Mouse: First, enable this function in CMOS Setup, then you can power on the system by double clicking the right or left button of your PS/ Mouse.. System power on by Keyboard: If your ATX power supply supports 00 ma 5V Stand-By current (dependent on the specification of keyboards), you can power on your system by entering password from the Keyboard after setting the Keyboard power on jumper and password in CMOS Setup.. Support Modem Ring-On (COM A and COM B).. Support steps ACPI LED. 5. ATi D RAGE graphics acceleration Onboard. 6. PCI Audio chip Onboard (Optional). 7. SB8558B LAN chip Onboard (Optional). 8. Wake-Up on LAN. (The ATX power supply supports larger than 70 ma 5V Stand-By current) (Optional). Pentium II / Celeron TM Processor MAINBOARD R

2 -

3 The author assumes no responsibility for any errors or omissions which may information contained herein. Third-party brands and names are the property of their respective Sound Blaster is a registered trademark of Creative Technology Ltd in the are trademarks of Creative Technology Ltd. November. 8, 998 Taipei, Taiwan

4 Quick Installation Guide I. Quick Installation Guide : CPU SPEED SETUP The default system bus speed is 66 / 00MHz. The user can select the system bus speed (SW) and change the DIP SWITCH (SW) selection to set up the CPU speed for - 6MHz processor. The CPU speed must match with the frequency RATIO. It will cause system hanging up if the frequency RATIO is higher than CPU's. SW (:O / :X) SW AGP 89 X X O X 8 O O O X 75 X O X X X X X X 8 8 O X O O O O X O O X X O SW (:O / :X) FREQ. RATIO DIP SWITCH (SW) X O X O O X.5 X X O O X O O X O X.5 X O X O X 5 O X X O X 5.5 X X X O X6 O O O X X6.5 X O O X Note: We don t recommend you to setup your system speed to 75,8,, or MHz because these frequencies are not the standard specifications for CPU, Chipset and most of the peripherals. Whether your system can run under 75, 8,, or MHz properly will depend on your hardware configurations:

5 CPU, SDRAM, Cards, etc.

6 Quick Installation Guide. Pentium II / Celeron / 66MHz FSB SW B PIIXE D RAGE SW. Pentium II / Celeron 66 / 66MHz FSB SW SW. Pentium II / Celeron 00 / Celeron 00A/ 66MHz FSB SW SW

7 . Pentium II / Celeron / 66MHz FSB SW SW 5. Pentium II / Celeron 66 / 66MHz FSB SW SW 6. Pentium II / Celeron 00 / 66MHz FSB SW SW 7. Pentium II / Celeron / 66MHz FSB SW SW 5

8 Quick Installation Guide 8. Pentium II 50 / 00MHz FSB SW SW 9. Pentium II 00 / 00MHz FSB SW SW 0.Pentium II 50 / 00MHz FSB SW SW.Pentium II 500 / 00MHz FSB SW SW 6

9 .Pentium II 550 / 00MHz FSB SW SW.Pentium II 600 / 00MHz FSB SW SW.Pentium II 650 / 00MHz FSB SW SW 7

10 Quick Installation Guide II. Jumper setting: J7 : CPU FAN PWR (CPU Cooling Fan Power Connector) 8558B 8 PIIXE D RAGE Pin No. Function GND +V SENSE J : System FAN PWR (System Cooling Fan Power Connector) 8558B 8 PIIXE D RAGE Pin No. Function GND +V SENSE 8

11 PS/ Mouse and IBM PS/ Keyboard Connector PS/ Mouse YMF7 8558B 8 D RAGE PIIXE PS/ Keyboard PS/ Mouse/Keyboard Pin No. Function Data NC GND VCC (+5V) 5 Clock 6 NC VGA : VGA Port YMF7 8558B 8 PIIXE D RAGE 9

12 Quick Installation Guide LPT : Printer Port YMF7 8558B 8 PIIXE D RAGE COM A : Serial port 8558B 8 PIIXE COM A D RAGE 0

13 COM B : Serial port 8558B 8 PIIXE COM B D RAGE USB : USB Connector 8558B 8 PIIXE D RAGE

14 Quick Installation Guide JP : Keyboard Power On JP 8 D RAGE 8558B PIIXE, Short : Enable Keyboard Power On., Short : (Default) Disable Keyboard Power On. JP6 : SB-LINK (Creative PCI Sound Card Support) 8558B 8 PIIXE JP6 6 5 Pin No. Function Signal GND NC Signal 5 GND 6 Signal D RAGE

15 J : LAN Power On (Optional) 8558B 8 PIIXE, Short : Enabled LAN Power On. D RAGE, Short : (Default) Disable LAN Power On. On-Board LAN Connector (Optional) B PIIXE - Yellow LED (LAN Active LED) Green LED (LAN Link LED) D RAGE

16 Quick Installation Guide JP : On-Board Sound Function (Optional) 8558B, Short : Disable On-Board Sound 8 PIIXE, Short : (Default) Enable On-Board Sound D RAGE Game Port / Audio Port (Optional) Audio Port 8558B MIC Line Out 8 PIIXE Line In CN Game Port D RAGE

17 CN : On-Board Sound CD-Line In (Optional) 8558B CN -Board Sound Function 8 PIIXE G R G L CD-ROM L G G R D RAGE JP9 : On-Board VGA 8558B JP9 8 PIIXE, Short : Disable On-Board VGA D RAGE, Short : (Default) Enable On-Board VGA 5

18 Quick Installation Guide JP8 : Release On-Board VGA from occupying IRQ Resource (It is not to enable or disable On-Board VGA Function.) JP8 8558B 8 PIIXE, Short : Disable VGA INT. D RAGE, Short : (Default) Enable VGA INT. JP : Internal Buzzer 8558B 8 PIIXE Buzzer JP Short : Enable Internal Buzzer D RAGE Open : Disable Internal Buzzer 6

19 JP7 : System Acceleration YMF B PIIXE - Turbo - 00MHz Normal Default: - 00MHz Normal - Turbo: For 00MHz Turbo and other frequencies - 00MHz Normal: For 00MHz Normal D RAGE JP0 : Onboard LAN Function (Optional) 8558B, short Onboard LAN Disable. 8 PIIXE, short (Default) Onboard LAN Enable. D RAGE 7

20 Quick Installation Guide JP0 : Suspend To RAM Function (Optional) YMF7 8 Short : Enable Suspend To RAM Function. 8558B Open : Normal Operation. When STR function is Enabled, please PIIXE do not unplug the SDRAM modules, for it will burn the SDRAMs and mainboard. D RAGE Support under Windows 98 ACPI O.S. When use STR function,it s depends on VGA brand version. JP9 : STR LED (Optional) 8558B 8 PIIXE + D RAGE 8

21 JP8 : CLEAR CMOS Function 8558B 8 PIIXE D RAGE - Short :Clear CMOS - Short :Normal Default: - Short JP7 : CASE OPEN 8558B 8 PIIXE D RAGE Pin No. Function Signal GND 9

22 Quick Installation Guide TEL : For Modem with internal voice connector(optional). 8558B 8 PIIXE D RAGE BAT : BATTERY 8558B 8 PIIXE D RAGE + Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer s instructions. 0

23 III. Top Performance Test Setting: Users have to modify the value for each item in chipset features as follow for top performance setting. ** Each value of items as above depends on your hardware configuration : CPU, SDRAM, Cards, etc. Please modify each value of items if your system does not work properly. The following performance data list is the testing results of some popular

24 Quick Installation Guide benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.) CPU DRAM CACHE SIZE DISPLAY STORAGE O.S. DRIVER Processor Pentium II 50MHz / Celeron TM 66 MHz processor (8 ) MB SDRAM (SEC KM8S800BT-GH) Included in CPU On-Board ATi D RAGE Pro X AGP Display (MB SGRAM) Onboard IDE (Seagate ST50A) Windows NT.0 (SPK) Display Driver at 0 x 768 x 6 colors x 75Hz. Triones Bus Master IDE Driver.70 Intel Pentium II Intel Celeron TM 50MHz (00.5) 66MHz (66 5.5) Winbench99 CPU mark 0 77 FPU Winmark Business Disk 70 0 Hi-End Disk Business Graphics 6 Hi-End Graphics 99 Winstone99 Business Hi-End 8.8.