Network Manual Ver. 1.1

Transcription

1 VDA110S-IP H.264 IP PTZ CAMERA IP PTZ Camera Network Manual Ver. 1.1 H.264 IP PTZ Camera Network Manual

2 CONTENTS 1. Introduction About This Manual 3 Features 3 System Connections 4 2. System Operation RemoteVideo Monitoring 6 Initialization of IP Address 7 3. True Manger True Manager Software 8 Server Registration and Removal 8 Server Connection Management 11 Server Status Monitoring 12 Network and System Diagnostics 13 F/W Upgrade 16 Remove Configuration and Video Monitoring Remote Configuration Using Internet Explore 17 Use OSD (On Screen Display) 18 System Configuration 19 Video Configuration 21 Audio Configuration 24 Network Configuration 25 Serial Port Configuration 28 Event Configuration 30 Preset Configuration 33 Record Configuration 34 User Configuration Specifications 40 4 H.264 IP Camera Network Manual 2/41

3 INTRODUCTION 1 About This Manual This User Manual provides information on network part of IP Camera, VDA110S. In this guide, information on operation and configuration of VDA110S is explained as well as how to shoot troubles when problems arise. Features VDA110S is a video and audio surveillance transmission system based on IP network through LAN, ADSL/VDSL, and Wireless LAN. Video High-Quality Compression Algorithm, H.264 Compression into Various Resolution : QCIF, CIF, Half-D1, D1 Wide Range of Video Transmission Rate : 32kbps ~ 4Mbps Various Transmission Mode : CBR, VBR Motion Detection Audio Various Transmission Mode : Unidirectional Mode, Bi-directional Mode Network Static IP and Dynamic IP(DHCP) Support One to One Connection and One to Multiple Connection Multi-Casting Automatic Transmission Rate Control by Network Condition User Interface System Status Display with OSD(On Screen Display) System Configuration via Internet Explorer Reliability Reliable Embedded System System Recovery with Dual Watch-Dog Function 4 H.264 IP Camera Network Manual 3/41

4 INTRODUCTION 1 System Connections VDA110S systems can be connected in either 1-to-1 fashion where a server is connected a PC client or a decoder system or 1-to-multiple fashion where a server can be simultaneously connected to many PC and many decoder systems. Topology Generally, the VDA110S and the PC & decoder are connected in 1-to-1 mode or 1-to-multiple connection is also supported. 1:1 Connection (Unidirectional Transmission). Site VDA110S Remote Center Decoder Site VDA110S Remote Center PC Mostly used configuration is 1 to 1 connection. VDA110S is installed at a site where video images can be transmitted and a PC or a decoder is installed at a center location to receive and view the video images on analog monitor. Audio data are transferred in either direction. 1:N Connection (Unidirectional Transmission). Site VDA110S Remote Center PC/Decoder PC/Decoder PC/Decoder In this configuration, a site can be monitored at many remote center locations. Although up to 64 PCs or decoders can be connected to on VDA110S, in the real network environment, network bandwidth can limit the maximum connections. Functionally, the CMS (Central Monitoring System) software can replace the decoder. 4 H.264 IP Camera Network Manual 4/41

5 INTRODUCTION 1 Multicast Mode Within the network that supports multicasting, a large number of decoders can be used to receive video effectively from a VDA110S using a single streaming of video and audio. Relaying Site Decoder Decoder VDA110S Remote Center #1 Remote Center #2 In this arrangement, video and audio can be retransmitted from a center to another center. The arrangement is useful when the network bandwidth to the site is limited while there is more than one center wanting to monitor the site. CMS(Central Monitoring System) Site VDA110S Remote Center CMS Site VDA110S Remote Center PC CMS CMS (Central Monitoring System) is a Windows based remote monitoring program to access multiple IPsevers for real-time monitoring or control of the encoders and connected cameras. Please refer to CMS User Manual for more information on CMS. 4 H.264 IP Camera Network Manual 5/41

6 SYSTEM OPERATION Part Names and Function Cable Configuration 12VDC Composite out ALARM INPUT Ethernet 4 H.264 IP Camera Network Manual 6/41

7 SYSTEM OPERATION 2 Remote Video Monitoring There are two ways to view video between the site and center system. In order for a proper operation, an IP address must be set accordingly and please refer to True Manager in Chapter 3 or Remote Setting in Chapter 4 for a further details. Default ID : admin Default Password : 1234 Video Monitoring with Decoder System Once the IP address is set in the remote IP address section of the decoder, the decoder system will connect to the VDA110S and start receiving the video images. Normally, a monitor connected to the decoder will display video images. Video Monitoring using Internet Explorer If an encoder s IP address is entered on the Internet Explorer, the system will ask for confirmation to install Active-X control. Once authorized, the Internet Explorer will start to display video images from the encoder as shown below. 4 H.264 IP Camera Network Manual 7/41

8 SYSTEM OPERATION 2 Initialization of IP Address If a system IP address is lost, the system can be reset to the system default IP address using the reset button in the back side of the system While system is in operation, press the reset button for more than 5 seconds. The system will reboot automatically Once the system reboots, IP address will be set to the system default as below. IP mode Fixed IP IP address Subnet mask Gateway Base port 2222 HTTP port 80 4 H.264 IP Camera Network Manual 8/41

9 USING TRUEMANAGER 3 True Manager Software True Manager is a program used for basic configuration, diagnostics and F/W upgrade of VDA110S. True Manager provides the following features. Finding servers on the LAN and assigning IP address Monitoring server status: encoding/decoding etc. Diagnostic Function: Ping, Network Bandwidth Measurement, Video/Audio Output Port Check F/W Upgrade Server Registration and Removal Server Registration In order to manage servers using True manager, the first step is to register the server. The following steps describe the way to register a server. Select Add Server on Server menu. Enter information for connecting to the server at Add Server dialog. 4 H.264 IP Camera Network Manual 9/41

10 USING TRUEMANAGER 3 If the server is registered on DDNS server, domain name can be used instead of IP address. When the IP address of the server is forgotten, it is possible to find the IP address of the server with IP Discovery function. (Please refer to IP Discovery section). Press Add button. Removal of a server A server can be removed by the following steps. Select a server to remove on Servers tab. The server should be highlighted with blue color. Select Remove Server on Server menu. Server selection Modification of information for a server Information on a server can be modified on the dialog invoked by selecting Modify Server Info on Server menu. 4 H.264 IP Camera Network Manual 10/41

11 USING TRUEMANAGER 3 IP Discovery With IP Discovery function, all servers on the same LAN where the PC executing True Manager is located can be found. Furthermore, it is possible to change IP address of a server easily. IP Discovery dialog is invoked by pressing IP Discovery button on Add Server dialog, and it shows all VDA110S on the same LAN. If you press Select button after selecting a server, the information on the server is automatically entered on Add Server dialog. Pressing IP Change button after selecting a server invokes a dialog on which IP address of the server can be changed. It is possible to change IP address of a server which has IP address of different subnet. Grouping of servers When there are large numbers of servers, it is convenient to manage servers in several groups. Using Add Group and Remove Group on Group menu, server group can be created and deleted. Modify Group menu is used to add servers to a group or to remove servers from a group. 4 H.264 IP Camera Network Manual 11/41

12 USING TRUEMANAGER 3 Server Connection Management Server connection If the check box on the first column in Servers (or Channels/Peripheral) tab, True Manager tries to connect to the server. If the server is running and the network where the server is in is normal, it will be connected immediately and State will be changed to Connected. Check box to connect or disconnect server If it fails to connect to the server due to server or network failure, State displays Trying connection. As soon as the server or network is recovered, it will be connected automatically. That is, True Manager periodically retries connection to servers with check box checked Server disconnection If the check box is unchecked, the connection to the server is released and State displays Disconnected. 4 H.264 IP Camera Network Manual 12/41

13 USING TRUEMANAGER 3 Server Status Monitoring Servers tab General information Servers tab shows general information on a connected server: MAC address, product model, system mode(type) F/W version and startup time. This information comes only for connected servers. Channels tab - Monitoring of video/audio channel state Channels tab displays how video channel and audio channel of servers are working. Item Ch Conns Cam Motion V-E(kbps) V-E(fps) V-D(kbps) V-D(fps) A-E(kbps) A-D(kbps) Displays Channel no. Number of clients connected to a server (including True Manager) Video loss status Motion status Video encoding bitrate Video encoding framerate Video decoding bitrate Video decoding framerate Audio encoding bitrate Audio decoding bitrate Depending on the system mode, items which are not relevant to the mode may display 0 always. For example, V- D(kbps) and V-D(fps) are always 0, if the system mode is Encoder. Peripherals tab Monitoring of serial, sensor and relay port This function is not available in this product. 4 H.264 IP Camera Network Manual 13/41

14 USING TRUEMANAGER 3 Network and System Diagnostics True Manager provides various diagnostic features. Connection between two VDA110S, or between VDA110S and CMS(Central Monitoring System) is established. Video, audio or serial data are not delivered as configured. Video and/or audio outputs don t come on output port. Ping test Ping Test dialog can be invoked by selecting Ping Test on Tools menu after selecting a server. Server executing Ping Destination of Ping Ping test is useful for checking if one or more remote systems are reachable from a server. Up to 4 systems can be registered as the targets of Ping test, which makes it possible to identify the hop(segment of network) where network failure may happen. For example, local router, remote router and remote Encoder can be pinged from a Decoder simultaneously. 4 H.264 IP Camera Network Manual 14/41

15 USING TRUEMANAGER 3 Network test Network Test dialog is invoked by selecting Network Test on Tools menu. Network test can be used for measuring effective bandwidth and/or packet loss rate between a server and PC running True Manager by generating test traffic of constant bitrate. This feature is useful for identifying the reason why video quality comes poorer than expected. TCP protocol can be selected for measuring effective bandwidth, while UDP protocol is appropriate for checking if the network is not reliable. System test Selecting System Test on Tools menu invokes a dialog on which system H/W status, video/audio output function can be diagnosed. 4 H.264 IP Camera Network Manual 15/41

16 USING TRUEMANAGER 3 System Check System Check tests if H/W components are fine and board ID and MAC address are displayed. Video Out Check / Display Color Bar It displays color bar on video output port. This function works for Decoder or Duplex mode, and is useful for checking if video output port or external display device is normal. Audio Out Check / Play Audio Clip It plays audio clip and outputs to audio output port. This function is useful for checking if audio output function of a server or external audio output devices such as amplifier and speaker are normal. Serial Loopback Test This function is not available in this product Viewing server s log The log in a server can be viewed by selecting Log on Tools menu. Remote rebooting of a server A server can be rebooted by selecting Reboot on Tools menu. 4 H.264 IP Camera Network Manual 16/41

17 USING TRUEMANAGER 3 F/W Upgrade When Update is selected on Tools menu, the dialog for F/W upgrade comes Select a server to upgrade (check the check box in Sel column). More than one server can be upgraded simultaneously. Select an upgrade file. Press Upgrade button. Wait until Progress is changed to Upgrade succeeded. Caution: Don t power-off the server while upgrade is in progress. The server may go to irrecoverable state When network condition is poor, upgrade may fail. In such case, please retry above procedure after network condition is recovered. Remove Configuration and Video Monitoring VDA110S provides web-based Setup and video viewing. If Setup on Server menu is selected, Internet Explorer is invoked and page for remote setup of the server is displayed. If Viewer is selected on the menu, Internet Explorer displays the video from the server. 4 H.264 IP Camera Network Manual 17/41

18 REMOTE CONFIGURATION 4 Using Internet Explorer The server can be configured using web browser. Type IP address in the address input area of Internet Explorer, then a live viewing screen will be displayed. Press Setup button located in the upper right area of the monitoring screen, then the setup page for server setup will be displayed. Enter IP address Press Setup button The configurations are grouped into 8 categories: System, Video, Audio, Network, Serial, Event, Preset and User. Any configuration changes are not applied until Apply is pressed. Leaving the page without pressing Apply button, changes in the page will be discarded. 4 H.264 IP Camera Network Manual 18/41

19 REMOTE CONFIGURATION 4 Use OSD(On Screen Display) MENU ON CAM NAME,LENS,EXPOSURE,DAY/NIGHT.WDR/BLC/ECLPS WHITE BALANCE,3D-DNR,EFFECTS,SPECIAL, Please, refer to the camera part of VDA110S user manual For further configuration. Drection key.left /Right/Top/Bottom button. Digital Zoom button 4 H.264 IP Camera Network Manual 19/41

20 REMOTE CONFIGURATION 4 System Configuration Video Standard System ID Language Firmware version Start Time Current Time Select NTSC or PAL Alphanumeric System ID to be transferred to remote software Language to be used for web-based configuration(english, Japanese and Korean) Current firmware version Latest system boot date and time Enter a new date and time and press Set Current Time button to update date & time 4 H.264 IP Camera Network Manual 20/41

21 Time Zone Automatically synchronize with Select time zone of where the system is installed. Depending on the time zone, Daylight Saving Time will work automatically Synchronize system time with an NTP server using NTP(network time protocol). Name of the NTP server should be registered on NTP server Name. NTP server Reboot Server Pressing Reboot Server button will cause the system to reboot. Do not press the Reboot button unless the server needs a reboot. 4 H.264 IP Camera Network Manual 21/41

22 REMOTE CONFIGURATION 4 Video Configuration 4 H.264 IP Camera Network Manual 22/41

23 REMOTE CONFIGURATION 4 Encoding Mode There are two encoding modes, Field Encoding and Frame Encoding. Since field encoding shows better quality of video, it is recommended to use field encoding mode as long as the decoder in the client can decode field encoded stream. In order to support clients which are able to decode frame encoded stream only, encoding has been made configurable. Field Encoding: Field encoding is the way to compress interlaced scene split into even and odd fields. Frame Encoding: Frame encoding is the way to compress each frame unites Preference Resolution Preference in video compression and transmission: With Bit rate selected, the video compression will be effected by the Bit rate value entered. With Quality selected, the video compression will be effected by the quality of image selected. Therefore, Bit rate and Quality corresponds to CBR and VBR respectively Selectable video compression resolution: NTSC: , , , , 176x120 PAL: , , , , 176x144 Frame rate Quality Bitrate I-Frame Interval Motion Detection Area Editing Selectable video frame rate: Determine the maximum number of frames of video images to compress. The frame rate of actually transmitted video can be affected by the network bandwidth limitation The selection is possible with Preference is set to Quality The value is applicable when Preference is set to Bit rate Possible values between 0 and 255. There will be no I-frames if 0 is selected. Configure regions for motion detection. Regions of arbitrary shape can be configured by the following steps. 1 Enable Edit item. 2 Select editing Mode. Set is for including cells to motion detection region and Erase is for excluding. 3 Select cells using the right button of the mouse. Multiple cells can be selected conveniently by press and dragging. 4 Press Apply Edited Area to save the editing. 4 H.264 IP Camera Network Manual 23/41

24 REMOTE CONFIGURATION 4 Sensitivity A condition to trigger an event with motion detection. The value determines the sensitivity of the motion detection within a block: the smaller, the more sensitive Brightness Controls input video brightness by selecting values between 0 and 100. Contrast Controls input video contrast by selecting values between 0 and 100 Hue Controls input video Hue by selecting values between 0 and 100 Saturation Controls input video saturation by selecting values between 0 and 100. Burn-in OSD Inserts system ID and date/time in the compressed video. Separately System ID and Time can be turned On or Off in the video. Position specifies the position of such data 4 H.264 IP Camera Network Manual 24/41

25 REMOTE CONFIGURATION 4 Audio Configuration Mode Select audio operation mode Mode Off Tx-Only Rx-Only Tx & Rx Action No operation Transmit only Receive only Transmit and Receive Input Gain Set audio input gain 4 H.264 IP Camera Network Manual 25/41

26 REMOTE CONFIGURATION 4 Network Configuration 4 H.264 IP Camera Network Manual 26/41

27 REMOTE CONFIGURATION 4 IP Mode Three IP modes are supported. Depending on the selected mode, further configuration items come as follows. IP Mode Selection Description Fixed IP Local IP Fixed IP address Local Gateway Local Subnet Gateway IP address Subnet mask DHCP N/A Please ask an IP address information from ISP provider or network manager DNS Set DNS server IP address Base Port HTTP Port RTSP Port RTSP Authentication RTP session Network base port use for communication between systems. In order for the servers and remote systems to be connected together, the port number must be identically set HTTP port use for web-based connection RTSP port used for RTSP-based connection Determine to use RTSP Authentication. If RTSP Authentication option is On on the Network page, user should enter correct User ID and Password when any RTSP client is connected RTP only streaming without RTSP connection is supported. SDP (Session Description Protocol) file can be found in the server, and a client can retrieve it using http connection. Network tab of web setup page provides related settings. Set IP and port for your destination system which will receive RTP stream. User Name will be used as session name in SDP file. File Name will be used as the name of the SDP file. Then, it can be accessed through SNMP Setup for using SNMP (Simple Network Management Protocol) SNMP Listen Port: The port is for connecting external devices when system operates as a SNMP client. SNMP is not used by setting 0 value. SNMP Trap Destination IP: Set the SNMP Trap Destination IP. SNMP Trap Destination Port: Set the SNMP Trap Destination Port. SNMP is not used by setting 0 value. Multicast IP The multicast IP address selection range is between and The selection can be used only when media protocol is set to Multicast. The multicast address must be the same for the system to be connected using multicast protocol DDNS Select the DDNS(Dynamic DNS) server to use Check IP Disable: If Check IP Disable is selected, Camera will skip to check its own IP. In Fixed IP mode, the set IP will be registered on DDNS server. In DHCP mode, the Allotted IP will be registered on DDNS server. 4 H.264 IP Camera Network Manual 27/41

28 REMOTE CONFIGURATION 4 Flow Control Mode When several clients connect to a server, bandwidths of networks clients may differ and some clients may not receive encoded stream fully. To handle such situation, three flow control modes which can be chosen according to users preference are provided Mode Min Max Adjust Off Description The bitrate is automatically adjusted to a client with smallest network bandwidth The bitrate automatically adjusted to a client with largest network bandwidth size. When set to this mode, a client with smaller bandwidth will not receive all frames of video The bitrate is adjusted to most optimum rate by learning the network bandwidth Flow control is off Address Info Display network related information IP Address Domain Name MAC Address Connecting The server own IP address. This information is useful when the server s IP mode is set to DHCP In case the server is registered with DDNS server, the registered domain name is displayed Display the MAC address of the server. In case the server is registered with DDNS server, the MAC address is used in DDNS registration Client IP Addresses that are currently connected to the camera are listed. 4 H.264 IP Camera Network Manual 28/41

29 REMOTE CONFIGURATION 4 Serial Port Configuration RS-485 serial port configurations must be same as configurations of connected analog PTZ camera. Default value of PTZ type, Pelco-D must be the same as protocol and ID of the analog PTZ camera Serial Port Configuration There is one serial port, RS-485, in VDA110S. The serial ports can be configured as follows Mode Bit rate Data Bits Parity Stop Bit Selection 2400, 4800, 9600, 19200, 38400, 57600, bps 5, 6, 7, 8 bits NONE, EVEN, ODD bit 1, 2 bit Default 9600bps,PELCO-D in VDA110S 4 H.264 IP Camera Network Manual 29/41

30 Sensor Type There is one sensor input port on VDA110S. The sensor port can be configured to the following. Function OFF NO (Normally Open) NC (Normally Closed) Operation Not used The port is normally open and activated when closed. The port is normally closed and activated when opened. The function of the sensor port is set based on the types of the sensor connected Event Configuration 4 H.264 IP Camera Network Manual 30/41

31 REMOTE CONFIGURATION 4 When a decoder system instead of a PC client is connected to a VDA110S, one system becomes a Local system and the other becomes a Remote system (Generally a system which is being used by the user is called as Local system). Then, actions for events can be configured for events from remote system as well as from local system. For example, it is possible to turn on an alarm device in local (center) decoder system when a sensor device in remote (site) IP camera is triggered. Local section configures the actions for events from local (self) system, and configuration activates local devices and Remote sections configures the actions for events from remote (peer) system. 4 H.264 IP Camera Network Manual 31/41

32 . The following table lists the possible actions for events. Action Description Sensor In Alarm out FTP Preset One sensor in port Alarm (relay) port will be triggered will be sent to the specified address. AVI file can be attached AVI file will be uploaded to a specified FTP server It is available for PTZ cameras Sensor The actions are configured when the sensor is activated. Multiple actions can be set for a single event. Video Loss The actions are configured when video input signal is lost. Multiple actions can be set for a single event. On Motion The actions are configured when motion is detected. Multiple actions can be set for a single event On Disconnection Alarm activation duration Notification The actions are configured when the link (connection) with peer system is disconnected. Multiple actions can be set for a single event The duration of alarm activation is set in case of an event. If it is set to continuous, it will be in active state until an operator reset it manually. Specify the information to send event information, when is selected as an event action. Server Address: Enter an address of mail(smtp) server Port: Specify a port for SMTP operation (Port 25 is the default port in SMTP operation. If a different port is configured in the SMTP server, this port needs to be changed accordingly). Sender Address: Enter an account registered in the SMTP server. ID & password: When the server requires authentication, ID and Password of an account need to be entered. Destination address: Enter Destination address. More than one address can be entered by delimiting comma (,) or semi-colon (;). Destination address can take up to 63 characters. Video Clip Attaching: Video clip stored at the moment of event can be attached as an AVI or JPEG file format. 4 FTP Upload Specify the information to upload event information, when FTP is selected as an 4 H.264 IP Camera Network Manual 32/41

33 REMOTE CONFIGURATION 4 event action Server Address: Enter an address of an FTP server to receive video files Port: Specify a port for FTP operation (Port 21 is the default port in FTP operation. If a different port is configured in the FTP server, this port needs to be changed accordingly.). ID & password: Enter ID and Password for accessing the FTP server. Continuous upload: Continuous upload on allows video image to be transmitted regularly, regardless of occurrence of events. Upload duration: Specify recording duration of a video clip to be transmitted. Upload interval: Specify transmission interval. Recording duration is not included in transmission interval. For example, if Upload interval is 60seconds and Upload duration is 20seconds, a Video clip for 20seconds is transmitted every 80seconds. Event Recording Specify how a video clip is to be generated for sending or FTP uploading. Pre-event Time: Specify the duration of recording before an event happens. Post-event Time: Specify the duration after the event is cleared. Max duration is 30 seconds 4 H.264 IP Camera Network Manual 33/41

34 Preset Configuration Preset Configuration Preset Name Move PTZ Camera to normal view Save Press Set Button Set the PTZ Presets by following the next steps Move cameras to desired view using PTZ control buttons. Enter Preset name. Press Set button. Once all the presets are set, press Save List button. Move to Preset Position Select a preset from the Preset and press Go To button, then, the camera will move to the selected preset position. 4 H.264 IP Camera Network Manual 34/41

35 REMOTE CONFIGURATION 4 Record Configuration Disk (USB, SD Card etc) Recording Disk Recording is not supported in VDA110S 4 H.264 IP Camera Network Manual 35/41

36 REMOTE CONFIGURATION 4 General 1. Off Record Recording function will not be used when Off is selected. 2. Use Disk Use record: To use disk for recording, select Use Disk Record File Format: Select Record file format between AVI or TCS (for CMS) Overwrite: In overwrite option, an action can be configured when the disk is full. If Overwrite Off is set, recording stops automatically when there is less than 100MB free space in the disk. If Overwrite On is set, recording continues by deleting the oldest data first on disk, maintaining free space of 300MB for normal operation. Max File Size: Max File Size option is for limiting the size of AVI file. If small file size is set, files of small size will be generated but numbers of the files will be increased. If recording time is more than 10 minutes, new file will be created even though previous file size is smaller than set max file size. Automatically Backup to FTP: Determine automatically back up to FTP Erase after Backup: Determine to erase data after backup or to keep date. Start Time of Backup Data: Specify Starting time and date of backup 4 H.264 IP Camera Network Manual 36/41

37 REMOTE CONFIGURATION 4 3. Use FTP While enabling FTP recording, FTP upload by event function is not available automatically This feature is to record video data to specified folder of FTP server using standard FTP protocol. The type of recorded file is ES stream of the H.264 video. The file name shows the date and time : Date_Begin Time_End Time.es Use record: To use FTP for recording, select Use FTP FTP Base Directory: If FTP base directory is specified, folder is created and files will be recorded into the folder. Max file Size: Max File Size option is for limiting the size of AVI file. If small file size is set, files of small size will be generated but numbers of the files will be increased. If recording time is more than 10 minutes, new file will be created even though previous file size is smaller than set max file size. Overwrite is not supported. This means video server (IP camera) will not erase any data written in the FTP server. Event Type Three recording modes are supported in VDA110S: Full-time, Event, Disconnect. In case of Event recording, event types can be selected among several events. Selected event type is used for configuring the schedule table. Up to 4 event types can be configured and each event type can be a combination of sensor, video loss and motion event. Pre-event Time: Specify the duration of recording before an event happens. Post-event Time: Specify the duration after the event is cleared Schedule Table Actual recording mode is determined by Schedule Table, where recording mode configured by day (of a week) and time. Each of recording mode configures the recording operation as follows: Record off : No recording Continuous : Records continuously Disconnect: Data is recorded when the system loses the connection to its client(decoder, CMS/NVR) etc. 4 H.264 IP Camera Network Manual 37/41

38 REMOTE CONFIGURATION 4 When one of its multiple clients system is disconnected, this doesn t happen. Event Type: Records when an event configured in Event Type setting happens. Checking the status of recording Recording status can be shown on the main view page. Recording status can be also shown in True Manager. When data is being recorded, Record column displays ON sign. 4 H.264 IP Camera Network Manual 38/41

39 REMOTE CONFIGURATION 4 User Configuration User can be registered and authority level of a user can be specified. User configuration is allowed only to admin user. MAX. 16 users can be registered and each user can have one of four authorities. Authority Level Allowed Operations Remarks Admin All operations User ID = admin Manager User Guest All operations except for user configuration Live viewing and PTZ control Live viewing only Add User Page for adding a user comes on pressing Add button. User ID and password need to be entered and privilege level need to be selected. User ID and password consist of alphanumeric string of MAX. 15characters. Delete User A user is deleted by pressing Delete button. Change Password Pressing Modify Password button after selecting a user shows a page for changing password. In case of changing admin password, the old password is checked. 4 H.264 IP Camera Network Manual 39/41

40 REMOTE CONFIGURATION 4 Modify Privilege Level Pressing Modify Privilege button after selecting a user shows a page for changing the authority. It is not allowed to change the authority level of admin user. Login Policy Skip Login is provided for convenient access to the server when authentication is not required. When Skip Login is set to Enable, login step is skipped. The privilege level after login in this way is determined by the setting of Privilege Level After Login Skipped. 4 H.264 IP Camera Network Manual 40/41

41 SPECIFICATIONS 5 Specifications Network Network Interface Network Protocol Ethernet 10/100 Base-T(RJ45) TCP/IP,UDP, Multicast, DHCP, SMTP, HTTP, SNMP RTSP, RTP Standard H.264 Data Rate 32Kbps ~ 4Mbps Video Resolution NTSC PAL : , , , , 176x120 : , , , , 176x144 Max Frame Rate NTSC : Max. 30fps PAL : Max. 25fps Frame Rate Range NTSC : 0.2 ~ 30fps PAL : 0.2 ~ 25fps Motion Detection Sensitivity adjustable Standard G.711 Audio Sample Rate Data Rate Input Output 8KHz 64Kbps 1 Line-In (Mini-Stereo) 1 Line-Out (Mini-Stereo) Video Access from Web-Browser Security Camera Live View & Audio/Video snapshot, PTZ control, Remote Setup, Remote Upgrade Multiple user access levels with password protection, IP address filtering, HTTPS encryption, IEEE authentication Max 36 Channel Monitoring simultaneously CMS Live Monitoring Search/Playback Backup PTZ Control Event Monitoring Bi-directional Audio communication Time/Camera-Base/Event-Base Multi-channel viewing of recorded status on timeline Export to AVI file Snapshot to BMP file 4 H.264 IP Camera Network Manual 41/41