Your Customized Instructions for Easy Installation & Assembly
|
|
- Daisy Strickland
- 7 years ago
- Views:
Transcription
1 Your Customized Instructions for Easy Installation & Assembly We know you will be amazed with the ease of installing elfa. If at any time during installation you have questions, call the store listed on your receipt or You may also visit containerstore.com/installation to view video instruction. Tools needed for the space: Pencil Level Power drill Drill bit set #2 Phillips head bit for power drill #2 Phillips head screwdriver Hammer Tape measure Ladder or step stool elfa 2' spacer Plastic mallet Scissors Products needed for the space: (Qty 1) Hardware Bag (Qty 1) 80" Top Track, Cut to 74" elfa décor Girl's Reach-In Closet Page 1 of 13
2 (Qty 1) 77-3/4" Mounted Standard (Qty 3) (Qty 1) Large Basket Medium Basket (Qty 1) Media Rack (Qty 1) Media Rack Dividers Pkg/2 (Qty 1) (Qty 3) 60" Hang Standard 84" Hang Standard (Qty 22) 16" Ventilated Shelf Bracket (Qty 6) Drawer Frame (Qty 2) 16" x 2' x 1-1/4" h Shelf (Qty 2) (Qty 4) Medium Mesh 1-Runner Medium Mesh 2-Runner (Qty 3) 16" Center Bracket Cover (Qty 3) 16" x 2' Ventilated Shelf (Qty 1) 2' Closet Rod Chrome (Qty 2) 16" x 4' Ventilated Shelf (Qty 1) 4' Closet Rod Chrome (Qty 7) Fascia 2' x 1-1/4" h (Qty 2) Top Track Cover Pkg/2 (Qty 7) (Qty 7) 16" Left Bracket Cover 16" Right Bracket Cover These instructions are only for the items you purchased. elfa décor Girl's Reach-In Closet Page 2 of 13
3 1. Getting Started Remove all contents from your space and donate or sell all items no longer needed. For closets, hang clothes that you are keeping on a garment rack outside the closet during installation. Take out any old shelving and/or closet rods. Patch and repaint walls. Tape the page(s) of your custom elfa design to the corresponding wall. Refer to your custom space design for placement of your elfa. Lay out all the products by type, size and wall. 2. Top Tracks Visit containerstore.com/installation to watch elfa Installation and Assembly Videos. Tools needed for this section: Pencil Level Power drill Drill bit set #2 Phillips head bit for power drill #2 Phillips head screwdriver Hammer Tape measure Ladder or step stool Products needed for this section: (Qty 1) 80" Top Track, Cut to 74" (Qty 1) Wood Screws Pkg/10 (Qty 2) Drywall & Plaster Anchors Pkg/5 Level the Track Place the Track at desired height (refer to your custom elfa design). Place the level at the bottom of the Track to ensure it is straight. While keeping your Track level, mark all the holes with a pencil. For longer Tracks, drill the center hole and secure with one screw. Tighten the screw just enough to hold the Track against the wall. Level the track and mark the rest of the holes. Set the Track aside, then drill all holes with a 1/8" drill bit. If you hit wood, continue drilling the entire length of the drill bit. In most applications, you will not hit wood for every hole. If you find you've hit the hollow part of the wall, mark that hole with a small 'X.' The 'X' is to remind you, after drilling all holes, to go back and enlarge that hole with the appropriate drill bit size for the hardware needed for your wall construction. elfa décor Girl's Reach-In Closet Page 3 of 13
4 Be careful not to drill into any electrical wires, ductwork, plumbing or other damageable components. If you have any questions on the locations of these wires or lines, please contact a professional electrician or plumber before drilling. Hardware Based on what you have told your designer, you have been provided with the correct hardware needed to complete the installation based on your wall construction. Below are instructions for installing your hardware: 1/2" thick drywall (most common wall type), 5/8" to 1" thick drywall/plaster Enlarge the hole with a 3/8" drill bit. Remove the screw from the white anchor, ensuring the gray insert stays in place. Tap the anchor into the hole. Discard the gray spacers that are included in the packaging. Wood or Wood Studs These will be tightened once any anchors have been placed in the wall and the Track is up against the wall. These are used for mounting the Track into drywall over wood studs or directly into wood. Rake the Wood Screw over a bar of soap before inserting it into the wall. This will make tightening the screw easier. Install the Track Place the Track on the wall, insert and tighten all the screws using a power drill with a #2 Phillips head bit. Tracks have a top and a bottom. The top is designated by two notches which allow Hanging Standards to be inserted properly. When tightening the drywall anchor screws, the screws will become flush with the Track as the anchors tighten. Continue to use the drill to tighten the screws until they become difficult to tighten or, when the driver bit starts to lose grip on the screw heads. Each screw will take approximately 20 seconds to properly tighten. To avoid stripping the screws, finish hand tightening with a #2 Phillips head screwdriver. 3. Wall Mounted Standards Tools needed for this section: Power drill Drill bit set #2 Phillips head bit for power drill #2 Phillips head screwdriver Hammer elfa décor Girl's Reach-In Closet Page 4 of 13
5 Products needed for this section: (Qty 2) Drywall & Plaster Anchors Pkg/5 (Qty 1) 77-3/4" Mounted Standard (Qty 1) Residential Overdoor Hooks Set of 2 (Qty 3) Large Basket (Qty 1) Medium Basket (Qty 1) Media Rack (Qty 1) Media Rack Dividers Pkg/2 If you hit wood, continue drilling the entire length of the drill bit. elfa décor Girl's Reach-In Closet Page 5 of 13
6 Install an elfa Door/Wall Rack System over a door Place the shorter hook (that features the screw) over the top of the door. Position the Standard so that the notches from the hook fit into the second set of slots on the Standard. Connect the longer hook at the bottom of the Standard and pull it down to lock it in position. The bottom hook should be loose and not tight against the base of the door. Position the unit to the desired location on the door. Use a level to make sure the Standard is square to the floor. Use the included wrench to tighten the screw on the hook at the top of the door. elfa décor Girl's Reach-In Closet Page 6 of 13
7 elfa décor Girl's Reach-In Closet Page 7 of 13
8 Install Door/Wall Rack baskets Determine the height at which you want to place them then align the tabs on the back of the basket with the slots on the Standard; press down. Install Media Rack Dividers Set the Media Rack Dividers into place by guiding them between the support wires at the front and back of the Media Rack, then pressing down. 4. Hanging Standard and Brackets Tools needed for this section: Tape measure elfa 2' spacer Products needed for this section: (Qty 1) 60" Hang Standard (Qty 3) 84" Hang Standard (Qty 22) 16" Ventilated Shelf Bracket Install the Hanging Standards and Shelf Brackets Insert the Hanging Standards in the Track notches. Group the Hanging Standards together and insert the Brackets at the appropriate height based on your custom elfa design. Using your elfa Spacer and following your custom elfa design, slide the Hanging Standards to their position on the Track. Hanging Standards should be a minimum of 1/2" from the ends of the Track. elfa décor Girl's Reach-In Closet Page 8 of 13
9 5. Products with 2' Spacing Products needed for this section: (Qty 6) Drawer Frame (Qty 2) 16" x 2' x 1-1/4" h Shelf (Qty 2) Medium Mesh 1-Runner (Qty 4) Medium Mesh 2-Runner (Qty 3) 16" Center Bracket Cover Install a U-Shaped Metal Glide The same U-Shaped Metal Glide is used for a variety of elfa components, including drawers, hampers and pant racks. The U-Shaped Metal Glide has three metal tabs and a metal knob on each side (located at the top of the glide) that locks the glide into the Bracket. Beginning on one side of the glide, align the metal tabs with the cut out notches of the bracket. Hold the front of the Bracket and press on the U-Shaped Metal Glide at the back rounded corner until you hear it lock into place. Repeat on the other side. To REPOSITION the U-Shaped Metal Glide: It is not necessary to remove the glide from the Brackets. Simply tilt up the front of both Brackets and remove them from the Standards. Place in the desired location. elfa décor Girl's Reach-In Closet Page 9 of 13
10 To REMOVE the U-Shaped Metal Glide from the Brackets: Place one hand at the back of the glide. With your thumb on the Standard, gently push the glide forward with your fingers. At the same time, insert and twist a small flat head screwdriver between the Bracket and U-Shaped Metal Glide in front of the knob holding the glide in place. The U-Shaped Metal Glide should pop out of the Bracket. Repeat on the other side. Install Center Bracket Covers If you are installing elfa decor gliding components side-by-side, the glides will share a bracket. When sharing a bracket, the Center Bracket Cover should be installed immediately after the U-shaped glides. Position it above the shared bracket and press into place. Install a Drawer Frame Before taking the Drawer Frame out of the box, remove the translucent plastic Drawer Clips found on the inside of the frame. Align the rollers on each side of the frame with the openings in the U-Shaped Metal Glide. Slide the frame into the glide. Insert the drawer into the frame opening and attach it to the left and right side of the frame with the Drawer Clips. Install a Decor Shelf Place the decor Shelf over the Brackets and press down to snap into place. elfa décor Girl's Reach-In Closet Page 10 of 13
11 6. Ventilated Shelves Products needed for this section: (Qty 3) 16" x 2' Ventilated Shelf (Qty 2) 16" x 4' Ventilated Shelf Install the Ventilated Shelves from shortest to longest, regardless of their location in the design. Ventilated Shelves have a top and a bottom. The middle support wire(s) is connected to the bottom of the Shelf. Place the shelf wires over the Bracket notches. Install the Shelf with end wires inside the Brackets. Lock the Shelf into place by pressing down on the middle of the Shelf and pushing toward the wall. To REPOSITION a Ventilated Shelf after it's been attached to the Brackets: Hold by the Brackets, and lift the front of the Shelf toward the ceiling and outward to release the entire unit from the Standards. To REMOVE a Ventilated Shelf from a Bracket while on the Standards, hold the Standard steady with one hand. Place the other hand at the back of the Shelf. Pull up and forward to release. 7. Closet Rods Tools needed for this section: Plastic mallet Products needed for this section: (Qty 5) Closet Rod Holder (Qty 1) 2' Closet Rod Chrome (Qty 1) 4' Closet Rod Chrome (Qty 2) Closet Rod End Caps Chrome Pkg/2 Install the Closet Rod Holders and Closet Rods Insert the Closet Rod Holder into the slot in the bottom of the each Ventilated Shelf Bracket based upon the placement of your closet rods in your custom elfa design. elfa décor Girl's Reach-In Closet Page 11 of 13
12 Tap the End Caps into both ends of the Closet Rod. Snap the Closet Rod into the Closet Rod Holders. 8. Finishing Touches Tools needed for this section: Scissors Products needed for this section: (Qty 7) Fascia 2' x 1-1/4" h (Qty 2) Top Track Cover Pkg/2 (Qty 7) 16" Left Bracket Cover (Qty 7) 16" Right Bracket Cover Install a Top Track Cover Install your Top Track Cover ONLY after you have placed all of your components and are satisfied with the positioning of your elfa Shelving. Because the Top Track Cover is placed between the Hanging Standards, the Shelves must be in place to ensure the spacing between the Hanging Standards is set. Start with long pieces first. Place the bottom of the Top Track Cover into the bottom of the Top Track, then ease the top of the Top Track Cover into the top of the Top Track. Measure the area on the Top Track where smaller pieces of the Top Track Cover are needed. Measure and mark the Top Track Cover where the cuts need to be. The Cover is easily cut in a straight line with scissors. Do not overlap segments of the Top Track Cover. Install Bracket Covers Left and Right Bracket Covers are not interchangeable and are clearly labeled. Place the outer edge of the Bracket Cover over the outer edge of the Ventilated Shelf Bracket. Push down from the back to the front to snap it into place. Install Fascia on Ventilated Shelves Position ALL pieces of Fascia before installing clips. elfa décor Girl's Reach-In Closet Page 12 of 13
13 Position the Fascia with the opening facing the Ventilated Shelf. The notch in the Fascia that hooks onto the front support wires of the Ventilated Shelf should be at the top. Hook over the top wire with a downward motion, and secure it to the front of the Shelf. Use the included clips to secure the Fascia to the Ventilated Shelf. The top of the clip features a groove that accommodates one shelf wire. Once it's attached to the underside of a shelf wire, slide it all the way to the front of the shelf and into the opening of the Fascia for a secure hold. Repeat with another clip at the opposite end of the Fascia. Congratulations! Your elfa solution is now complete! Thank you for your purchase and we look forward to seeing you again soon. Now that you have a fabulously organized elfa space, share it with us on Facebook at facebook.com/containerstore. elfa décor Girl's Reach-In Closet Page 13 of 13
DIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS
DIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS TheRTAStore.com STEP 1: CLEAR A WORK SPACE Place your RTA cabinet panels on a smooth, scratch resistant surface in a large, open area. (Some people like to
More informationBasic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
More informationPanel Track Installation Guide
Panel Track Installation Guide We make it easy! BTG 493361 EN_0510 Before starting Your new Blinds To Go panel track is custom made to your specifications from the finest materials available. To ensure
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationCustomer Service 800.780.8889 or visit us online at smithnoble.com. Wood Shutters. Step by Step Installation. Troubleshooting Tips
reflect your style TM Customer Service 800.780.8889 or visit us online at smithnoble.com Wood Shutters Step by Step Installation Troubleshooting Tips Easy Care Instructions STEP 1 Your New Shutter Thank
More informationTENSION ISSUES? ROLLER SEE PAGE 7
ROLLER TENSION ISSUES? SEE PAGE 7 Roller Shade Installation Guide Important: If you have ordered a valance for your shade, you must first read the Valance Installation Guide found in your box. We make
More informationBeadboard Wall Bookcase
Beadboard Wall Bookcase Note: The maximum load for each shelf is 30lbs.This hanging system is meant for drywall/wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
More informationHorizontal Mini Blinds Installation Guide
Horizontal Mini Blinds Installation Guide We make it easy! BTG 468298 EN_ rev0614 For more safety information: 1-866-662-0666 or.www.healthcanada.gc.ca/blindcords Before starting Your new Blinds To Go
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationAll-Season Sunroom Sliding Glass Door Installation Instructions
ASRESGD-08 All-Season Sunroom Sliding Glass Door Installation Instructions Panel Frame Door Frame Left Side Foam Insulator IE241 H Bar Assembly Door Frame Top Track Panel Frame Door Frame Right Side Stationary
More informationModels A spe n, Econoline C o l o n i al. and Savoy. Installation Instructions. Contractors Wardrobe
Installation Instructions Models A spe n, Econoline C o l o n i al and Savoy Contractors Wardrobe DESIGNERS MANUFACTURERS TOLL FREE: (800) CW-DOORS (800) 293-77 www.cwdoor.com 2121 Avenue Hall Valencia,
More informationBase Cabinet Assembly Instructions
Base Cabinet Assembly Instructions Publication Number TSG-BCAI-001 Version 1.0 July 2012 2012 The Shekia Group, LLC (TSG) All Rights Reserved. Notice Every effort was made to ensure that the information
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationElo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors
Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...
More informationCONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-AG Note: 40 lbs. of sand required!
More informationCabinetry Installation
Cabinetry Installation INTALLATION EQUIPMENT #8 x 2 1 2 screws #8 x 2 1 2 washer head screws Variable speed drill, electric or cordless Extension cord Countersink drill bit Drill bits, 3/16 and 1/4 Assorted
More informationPremier & Deluxe 3-Season Room Sliding Glass Door
DTSSGD-11 Premier & Deluxe 3-Season Room Sliding Glass Door Installation Instructions Screen Door Seal Left Side Track Top Track Assembly Right Side Track Right Side Trim Sliding Glass Door Sliding Screen
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationHollow or Cinder Block Wall Mount Job Aid
Summary This Job Aid covers: Hollow or Cinder Block Wall Mount Job Aid Hollow or Cinder Block wall Mount Bracket Installing the Mount Bracket into Cinder Block This Job Aid supports the Technician audience.
More informationPOD Visor Instructions
POD Visor Instructions Please read fully before beginning assembly and mounting the Visor Parts List - Visor Left Part (LV), Visor Right Part (RV) Qty 2, Aluminum Crossbars Hardware - Qty 17, 1/4" X 3/4"
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS Instruction Booklet 18 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More information1 Door Tall Unit ASSEMBLY GUIDE. Page 1 of 9. WARNING: Contains small parts, keep out of reach of children.
Page 1 of 9 ASSEMBLY GUIDE 1 Door Tall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please
More informationWren Kitchens Installation Tips... 3. Carefully check your kitchen delivery... 4. Measuring out and marking up... 5. Fitting the base cabinets...
tra 1 Index Wren Kitchens Installation Tips... 3 Carefully check your kitchen delivery... 4 Measuring out and marking up... 5 Fitting the base cabinets... 6 Fitting the corner cabinets... 7 The 972mm or
More informationmajestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base
majestic install ation guide barcelona three sided enclosure 24mm surface mounted wall channels and underframe to base These Instructions are for a left and right handed unit. The diagrams show a left
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationHALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL
HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL Please read these instructions carefully and completely before attempting to install Hale Pet Doors; they will guide you through the steps
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationHOW TO INSTALL A BEAUTIFUL NEW KITCHEN
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge
More informationTONNEAU INSTALLATION GUIDE
TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 4056 Toyota Tacoma Double Cab 5' Short Bed 2005-Current (With Multi-Track System) EASY AS 1-2-3! NORMAL INSTALLATION TIME 30 MINUTES For Warranty
More informationAssembly Instructions Model 1544 Heart-Of-The-Kitchen Island
Assembly Instructions Model 1544 Heart-Of-The-Kitchen Island A. These units are Ready-to-Assemble. Catskill uses positive fastening methods such as wood screws and in some places hidden Bastion fasteners.
More informationInstalling the Video Input and TV Tuner Cards in a Compact Computer or a Dual PCI-Slot Tower Computer
Installing the Video Input and TV Tuner Cards in a Compact Computer or a Dual PCI-Slot Tower Computer This booklet describes how to install the video input and TV tuner cards in a compact Macintosh computer
More informationCombination Unit 5'6" Windows a i o P t
for Andersen 5'6" Double-Hung Venting s Windows a i o P t o rs D o Congratulations You have just purchased one of the many fine Andersen products. For ease of assembly and installation and continued enjoyment
More informationService Guide. Gateway M275
Service Guide Gateway M275 Contents Replacing Gateway M275 Components.................................... 1 Identifying the convertible tablet PC model...................................... 2 Identifying
More informationRetail Reception kiosk
Retail Reception kiosk put 42" corner post in below 66" to allow post to extend above kiosk for raised box sign Mini cantilever option - 24" overhead support leg Mini cantilever option - 24" overhead 66/48E
More informationSLIDING PATIO DOOR INSTALLATION INSTRUCTIONS USING FRAME SCREWS
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V984528 2012 Pella Corporation SLIDING PATIO DOOR INSTALLATION INSTRUCTIONS USING FRAME SCREWS Installation Instructions for Typical
More informationInstalling Shutters using Fasteners
Installing Shutters using Fasteners Electric drill, ¼" drill bit, 3 8" drill bit, hammer, and shutter fasteners. (¼" carbide drill bit is required for stucco, hardboard, fiber cement, brick or masonry.)
More informationFRONT WINDSHIELD SEAL INSTALLATION
FRONT WINDSHIELD SEAL INSTALLATION Tech Article From Newsletter 16.1-1st Quarter of 2010 Replacing your Front Windshield Seal ISN T AS HARD AS YOU MAY THINK! Recently, we retooled our front window seal
More informationwww.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
More informationBUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS
BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More information1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS
By Denny Williams Photos by Denny Williams 1958-64 WINDOW CHANNEL, WEATHERSTRIP & WHISKER STRIP REPLACEMENT FOR 2-DOOR SEDANS Denny Williams - Technical Writer Denny is first and foremost a dyed-in-thewool
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationVinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows
Vinyl Brick Mould Field Installation Instructions All Vinyl and Vinyl Clad Windows Viewed from the exterior. IMPORTANT: Please read before you begin installation. TABLE OF CONTENTS AND TOOL / MATERIAL
More informationSteel Door Frame Installation in Steel Stud Construction
Steel Door Frame Installation in Steel Stud Construction For use with the Steel Door Institute (SDI) video How to Install a Steel Door Frames in Steel Stud Construction This manual gives you step-by-step
More informationK. D. FRAME ASSEMBLY FOR CLOSED STEEL STUD WALLS...Ins 10. FRAME INSTALLATION DETAILS FOR CLOSED STEEL STUD WALLS...Ins 11
K. D. FRAME ASSEMBLY FOR MASONRY WALLS...........................Ins 2 FRAME INSTALLATION DETAILS FOR MASONRY WALLS......................Ins 3 INSTALLING EXISTING MASONRY WALL ANCHORS IN FRAME..................Ins
More information2&3 SECTION LOFT LADDER
TWIST CATCH ASSEMBLY A4 A2 A1 A3 A7 A6 A5 2&3 SECTION LOFT LADDER Images feature the 3 section loft ladder, but the same instructions apply to both 2 & 3 section ladders Installation and Operating Instructions
More informationSPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS
SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS README FIRST: Thank you for purchasing your MyDIYCNC Desktop CNC Machine Kit. We hope this versatile and innovative machine brings you many
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationCongratulations on your new IKEA Kitchen, and on the money you saved!
Congratulations on your new IKEA Kitchen, and on the money you saved! INSTALLATION GUIDE FOR YOUR AKURUM KITCHEN Seven steps to a brand new kitchen It s time to discover another major advantage of investing
More informationItem #: BTOL Assembly Instructions
Item #: BTOL Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com
More informationDell P Series Monitor VESA Mounting Bracket Installation Instructions
Dell P Series Monitor VESA Mounting Bracket Installation Instructions The VESA mounting bracket enables a Wyse cloud client to be mounted to the Dell P Series Monitor and the Dell E24 Monitor. The cloud
More informationInstallation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step
More informationSeismic Installation for Attic Storage System
Your Performance Partner Seismic Installation for Storage System CONTENTS SSafety Precautions................................. 2 Required Tools..................................... 2 Parts and Fastener
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationINSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS
2009 Pella Corporation INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS Part Number: 80WH0100 Installation Instructions for Typical Wood Frame Construction.
More informationBUILD A TABLETOP LOOM
BUILD A TABLETOP LOOM From 1" x 2" stock (actual 3/4" x 1"1/2) cut: 4 pieces 15" long 4 pieces 5"1/2 long Use the above to make 2 frames for the front and back of the loom. From 1" x 4" stock (actual 3/4"
More informationINSTALLATION MANUAL. Contents JAPANESE ENGLISH GERMAN FRENCH ITALIAN SPANISH. To the installing technician: CEILING BRACKET
Be sure to read this installation manual thoroughly prior to installation. If installation methods or non-standard parts not specified in this installation manual are used, accidents or injury may result.
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationInstructions for assembly of your Pop-Up Display
Instructions for assembly of your Pop-Up Display I: Frame a) With the Pop-Up Frame still in the travel case, open the cloth bag. Make note of the ten black pegs on the top. These pegs represent the TOP
More informationKEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationSash Replacement Guide
for Andersen 200/400 Series Awning Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen at 1-888-888-7020
More informationAll seam allowances are 1/2 unless otherwise noted. All pattern pieces include the seam allowance. Please read all instructions before beginning.
This structured bag has lots of pretty detailing. It s large enough to carry all of your essentials as well. Make it in a great patchwork, or stick to a single fabric! All seam allowances are 1/2 unless
More informationINSTRUCTIONS: LocknCharge Laptop Carts
INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationCordlessPleated FabricShade including Top-Down/Bottom-Up. owner's handbook
CordlessPleated FabricShade including Top-Down/Bottom-Up owner's handbook July, 2013 español página 9 2 INSTALLATION INSTRUCTIONS Step 1. Check Package Contents Missing part? Call 1-800-264-1190 Mounting
More informationInstructions for Using the Watch Works Tool Kit to Change a Watch Battery
Instructions for Using the Watch Works Tool Kit to Change a Watch Battery Click on this link http://www.allamericanwatches.com/site/626101/product/e2306-a to purchase the Watch Battery Replacement Tool
More informationCable Drum Installation
20 Cable Drum Installation COUNTERBALANCE None Shake the TorqueMaster spring tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand
More informationInstallation Instructions 4508 4508S
SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More informationCombination Unit (shown from interior) WARNING
for Andersen Double-Hung Venting s Windows a i o P t o rs D o Congratulations You have just purchased one of the many fine Andersen products. For ease of assembly and installation and continued enjoyment
More informationInstallation Manual. SKU# 21000 series (Base Rails) SKU# 22000 series (Overhead Racks)
Installation Manual SKU# 21000 series (Base Rails) SKU# 22000 series (Overhead Racks) Welcome to the world of TracRac! We re delighted that you have chosen TracRac, the ultimate sliding truck rack system.
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationILLUSION FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
PREPARATION Approximate Installation Time: Tools Required for Installation: 60 minutes Hacksaw Electric Drill 3/16 Masonry Bit Pencil/Felt tip pen Safety Glasses Measuring Tape Masking Tape Standard Screw
More informationStandard Royal Inspiration Station
IS2 Standard Royal Inspiration Station R Assembly uide IS2_2013_A Check out our other products online at www.copernicused.com or assistance, please contact us: 1-800-267-8494 Email info@copernicused.com
More informationGuidelines for Earthquake Bracing Residential Water Heaters
Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the
More informationHermanMiller Aeron Posturefit Installation AE905A AE905B AE905C
HermanMiller Aeron Posturefit Installation AE905A AE905B AE905C Y How to assemble to your chair Parts Included Posturefit Mechanism For more information about our products and services or to see a list
More informationYour Simple Guide to Battery. www.firstalertpro.com. Replacement. Customer Care: 1-800-852-0086. www.firstalertpro.
Previous Menu Your Simple Guide to Battery www.firstalertpro.com Replacement p e t s ts ep -by Customer Care: 1-800-852-0086 FA/1565 9/00 www.firstalertpro.com Table of Contents: page Introduction...............................
More informationChapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationAstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationBy SP Partners, LLC. www.rainbowatticstair.com INSTALLATION GUIDE. Prestige
By SP Partners, LLC www.rainbowatticstair.com INSTALLATION GUIDE Prestige IMPORTANT READ THIS FIRST Inspect stair for any damage prior to installation. Stair is NOT to be installed while home is under
More informationAnthro Tablet Charging Cabinets
Owner's Manual for Anthro Tablet Charging Cabinets Covers part numbers beginning TAB16 and TAB20. Components at a Glance The open views of the front and side of the cabinet below are for the TAB20 cabinet.
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
More informationSERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair
SERVICE MANUAL US Corpus 3G Seat system for electric wheelchair How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Version 4, 2014-07 Item No.: 205260-US-0
More informationGE Wireless Devices Battery Replacement
60-506-319.5 Crystal Smoke Detector Two 9V Duracell 9V 1. Twist counter-clockwise until detector become loose from base. 2. Replace batteries observing correct polarity. 3. Replace detector by twisting
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray.
More informationAssembly Instructions
Assembly Instructions Overhead Storage Rack 4 x 8 3 x 8 2 x 8 4 x 6 3 x 6 2 x 6 4 x 4 Two 4x8 Racks Pictured Eagle Industrial Group, Inc. 25471 Arctic Ocean Drive Lake Forest, CA 92630 877.655.3443 888.313.9228
More informationPANELIZED HOME INSTALLATION GUIDELINE
PANELIZED HOME INSTALLATION GUIDELINE A typical home package will be constructed of Snap-N-Lock Insulated Panels clad with steel skins. 4" panels will be used for the walls, and 6" panels for the roof.
More informationChelsea Loft Bed WARNING:
Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE
More informationPicnic Table Plans. Made out of a single sheet of plywood, it s also portable! By Kevin Ayer. This children's picnic table would
Picnic Table Plans Made out of a single sheet of plywood, it s also portable! By Kevin Ayer Materials One 4- by 8-foot sheet of 3 4-inch AC plywood Twelve 11 4-inch wood screws Primer and exterior paint
More informationSPIRAL STAIR KIT INSTALLATION MANUAL
SPIRAL STAIR KIT INSTALLATION MANUAL Effective January 1, 2014 If you have any questions, please call the location that your Stair Kit was purchased from: Broomall, Pennsylvania 1-800-52-7427 Ontario,
More informationPlans will call for one of two soffit/fascia details:
Plans will call for one of two soffit/fascia details: Ventilated vinyl soffit with bent aluminum fascia OR Ventilated LP Smartside soffit panels with 1x6 rabbeted fascia First, let s talk terminology:
More informationRoll-Up Door Maintenance Guide
R Roll-Up Door Maintenance Guide Cable Replacement on Two Spring Type Balancer Page 1 Panel Replacement - Removable Roller Cover Type Bottom Panel Page 1 Panel Replacement - Removable Roller Cover Type
More informationEasy Assembly Instructions & Rules
Model #64-2000 Easy Assembly Instructions & Rules 4-in-1 Casino Table DO NOT RETURN TO STORE. FOR ALL RETURNS AND WARRANTY COVERAGE PLEASE CALL GLD PRODUCTS: 1-800-225-7593 Please provide model number,
More information