Passport 1000 PG. Offline Campus Access Control Products

Transcription

1 Offline Campus Access Control Products Available through Authorized Channel Partners only. Contact your local PERSONA or ASSA ABLOY Door Security Solutions sales consultant for details. Copyright 2008, 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

2 Table of Contents Table of Contents Overview....1 Product Features of PG...2 Mortise....3 Bored...4 Exit Devices...5 Finishes, ET Trim and Handing...6 Lever Trim Designs Prefixes...10 Architectural Specifications...11 As part of their promise to provide innovative, fast and effective high security solutions to their customers, certain ASSA ABLOY Group brands offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx is a registered trademark of ASSA ABLOY Inc. Offline MicroShield As part of their promise to provide innovative solutions to their customers, certain ASSA ABLOY Group brands offer the MicroShield technology, a silver-based antimicrobial coating designed to inhibit the growth of bacteria. MicroShield is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. MicroShield Coating Revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compound from Agion Technologies As an integral part of the finish coating, MicroShield lasts for the life of the hardware Available through Authorized Channel Partners only. Contact your local ASSA ABLOY Door Security Solutions sales consultant for details. For more information or a personal demonstration, contact PERSONA at or visit MicroShield coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. It is effective against a broad spectrum of bacteria. Non-toxic and completely safe. The Agion antimicrobial compound is EPA and NSF approved and FDA listed for use in medical and food preparation equipment. Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools, medical centers, daycare, food processing etc.) On the Cover KP-PG Mortise Lock 2

3 Overview, Features, Technical Information and Accessories Overview The SARGENT lock is an offline product powered by PERSONA Campus 1000 Offline Software. Designed specifically for the needs of today s campuses, this high security Grade 1 quality battery operated lock offers an efficient and cost-effective solution for comprehensive, reliable access control. features: PIN code: 4-digits with card, or 6-digits PIN only Comprehensive access control for campus housing and facilities Integrates into a One Card campus solution Flexible card issuing stations for mass check-ins Multiple hardware solutions for every door type Simplified migration to WiFi or Power over Ethernet locks Efficient and convenient security and life-safety from SARGENT. The provides stand alone access control and event logging. The lock s four-tiered operating mode of passage, card only, card+pin or PIN only, offers the flexibility to tailor security from building to building, room to room, even door to door. The system uses a standard, high or low coercivity magnetic stripe card with card tracks 1 or 3 open for encoding. The key override option provides a means of access in emergency situations. solutions offer secure, stand alone access control with event tracking and reporting. Functionality is similar to a traditional key card access system without the need for expensive wiring to each door or proprietary access control panels PERSONA Campus 1000 Offline Software Features Most existing magstripe ID cards work with the system including high or low coercivity magnetic stripes Importing student or personnel information is easy with the import module without duplicating existing databases Administrators can encode key cards quickly and easily with Conference Guest Wizard Connects to an external database for seamless integration of common information The System Events Log is password protected; level of security is user-configurable Time scheduling allows different access to various users at designated times throughout the day Can perform individual user or group searches and generate reports Deadbolt override is granted at user-specified doors for individual key card holders/users or globally for specific cardholders Remote technical support is available via modem or internet Assign pre-defined access patterns and access points as well as key card start and end times to individual users New key cards can invalidate and reactivate key cards/users no need to reprogram the lock! PERSONA s Campus 1000 Software runs on a single PC as a stand alone system or networked with existing TCP/IP networks on Microsoft Windows Technical Information PIN code: 4-digits with card, or 6-digits PIN only Operating temperature: 32 F to 104 F (inside) Operating temperature: -4 F to 104 F Humidity: <95% non-condensing Storage temperature: -22 F (-30 C) to 176 F (80 C) Power supply: 6 AA alkaline batteries or special climate battery package Voltage: (max/min) 9VDC/5.5VDC Expected lock battery lifetime: 1 to 3 years dependent upon usage Read speed: 4 to 40 in/s Magnetic head lifetime: 300,000 operations Monitoring: EMK, Deadbolt, Auxiliary latch Card track: Track 1 or 3 Card Coercivity: HiCo (4000 Oersted) or LoCo (300 Oersted) Time resolution on card: 1 minute Battery life is supervised and gives advanced warnings at low capacity Accessories (contact PERSONA) PERSONA Campus 1000 Offline Software Multitrack encoder Pocket PC Magstripe card 1

4 Features PASSPORT 1000 PG Exit Device shown The KP-PG- (keypad/magstripe card insert) version of these stand-alone products offers ultra-reliable first-time reads through industry proven technology. It can be used for a variety of applications, including academic environments, as well as corporate, medical and military campuses Bored Lock shown The PG- (magstripe card insert) version of these stand-alone products offers ultra-reliable first-time reads through industry proven technology. Ideal for a variety of applications, it can be used in academic environments, as well as corporate, medical and military campuses. 2

5 Mortise The SARGENT motorized 8200 Series Mortise Lock has a clean, crisp design and can be aesthetically complemented by SARGENT Studio Collection and Coastal Series levers, as well as traditional lever designs along with a full array of finishes. The Mortise Lock offers stand alone Access Control solutions for academic, military and medical campuses. This lock is available with or without deadbolt and with or without cylinder override. Mechanical Features Certified to and exceeds ANSI/BHMA A Series 1000 Operational Grade 1 and Security Grade 1 Motor driven Mortise Lock 3/4" Stainless steel, anti-friction reversible latch For 1-3/4" (44mm) thick door standard. Consult factory for other thicknesses 1" Hardened stainless steel deadbolt Stainless steel non-handed deadlocking latch Handed lockbody, easily field reversible without opening lockbody Lever trim through-bolted for increased security and durability Cylinder override requires a #41 Cylinder (1-1/8") Not available with SC- or SE- prefixes Batteries included Entry PG-Products: Electronic Access with Magstripe Card only KP-PG-Products: Electronic Access with Magstripe Card and Keypad Key outside retracts latch when trim is locked electronically Outside lever rigid except when in passage mode or valid user code entered When deadbolt thrown, outside lever operable only with Emergency or Master code Trim inside always retracts latch Guardbolt deadlocks latch Request-to-Exit (REX), Latchbolt Monitoring Reports, Key Override and Door Propped are standard Inside/Outside Escutcheon Solid diecast zinc Operating temperature -40 F (-40 C) to 135 F (57 C) A multi-colored LED indicates valid/invalid entries Keys/buttons are silk screened on backside to eliminate wear Outside Escutcheon Projection is 1-5/8" (41mm) Inside Escutcheon Projection is 1-5/8" (41mm) PG Mortise Lock Functions If the lock needs to have: 3-3/4" (95mm) KP-PG x LNL (Shown) 13-1/2" (343mm) Outside Shown How to Order: Mortise with Proximity Reader Then select: Technology Series Type Function Magnetic Stripe only Key override and deadbolt PG Key override and no deadbolt PG Deadbolt and no key override PG No deadbolt and no key override PG Magnetic Stripe & Keypad Key override and deadbolt KP- PG Key override and no deadbolt KP- PG Deadbolt and no key override KP- PG No deadbolt and no key override KP- PG Inside Shown Options Technology Series Type Function Roses Levers Finish Hand Select from pages 10 Select from PG Mortise Lock Function chart above Select rose, lever and finish from pages 6-9 RHR, LHR, RH or LH Example: KP-PG LN MX 03 RH 3

6 Bored The SARGENT motorized 10 Line Bored Lock is available with a wide selection of lever designs and hardware finishes. Its unique design provides uniformity when used with other SARGENT Bored at a facility, while offering Access Control solutions for dormitories, book stores, libraries, sports complexes and other campus applications. Mechanical Features Certified to and exceeds ANSI/BHMA A156.2 Series Grade 1 Motor driven bored lock Latch Stainless Steel, 1/2" (13mm) throw 2-3/4" (70mm) Backset standard. 3-3/4" and 5" backsets also available. For 1-3/4" (44mm) thick door standard. Consult factory for other thicknesses Handed (Specify RH, RHR, LH or LHR) Heavy duty lever spring return 3 through-bolt position combinations Steel mounting studs Cylinder override standard Not available with 10-UL-, 82-, 83-, 84- or VS- prefixes Batteries included PG-10G77 - Entry Lock with Cylinder PG-Products: Electronic Access with Magstripe Card only KP-PG-Products: Electronic Access with Magstripe Card and Keypad Key outside always retracts latch Lever outside rigid except when in passage mode or valid user code entered Lever inside always retracts latch Guardbolt deadlocks latch Door Position Switch (DPS, part #3287) supplied to allow for full monitoring 10 Line Levers and Roses (Shown on page 7) PG Cylindrical Lock Functions If the lock needs to have: Then select: Technology Series Type Function Magnetic Stripe only Key override PG 10 G77 Magnetic Stripe & Keypad Key override KP- PG 10 G77 Escutcheons Solid diecast zinc A multi-colored LED indicates valid/invalid entries Projection at bottom 11/16" (17mm) less lever Projection at top 1-5/8" (41mm) Outside Escutcheon Projection is 1-5/8" (41mm) Inside Escutcheon Projection is 1-5/8" (41mm) Keys/buttons are silk screened on backside to eliminate wear Operating temperature -40 F (-40 C) to 135 F (57 C) How to Order: Cylindrical KP-PG-10G77 x LL (Shown) 3-3/4" (95mm) Inside Shown 14-1/4" (362mm) 3-3/4" (95mm) Outside Shown 14-1/4" (362mm) Options Technology Series Type Function Roses Levers Finish Hand Select from pages 10 Select from PG Cylindrical Lock Function chart above Select rose, lever and finish from pages 6 & 7 RHR, LHR, RH or LH Example: KP-PG-10G77 L G 03 RH 4

7 Exit Devices The SARGENT 80 Series Exit Devices can be aesthetically complemented by SARGENT Studio Collection and Coastal Series levers, as well as traditional lever designs along with a full array of finishes. SARGENT 8800 Series Rim Exit Devices and 8900 Series Mortise Lock Exit Devices are available with the technology of the Persona Passport 1000 with or without cylinder override. Available with stand alone technology, these products can provide Access Control in academic, medical and military environments, and particularly in areas where life-safety is a primary concern (e.g., in stairwell areas or tenant-occupied facilities). Mechanical Features Certified to and exceeds ANSI/BHMA A156.3 Grade 1 Motor-driven ET trim Latch 3/4" (19mm) stainless steel latch for Rim Latch 3/4" (19mm) brass latch for Mortise Exit Devices For 1-3/4" (44mm) door standard. Consult factory for other thicknesses 8877 Rim Exit Devices require a #34 rim cylinder 8977 Mortise Exit Devices require a #46 Mortise cylinder (1-3/4") Cylinder override not available for 8878 and not available with 70-, 72-, 73-, 73-7P-, SC- or SE- prefixes Exit Devices PG-Products: Electronic Access with Magstripe Card only KP-PG-Products: Electronic Access with Magstripe Card and Keypad Always allows free egress Cylinder override retracts latch Lever outside rigid except when in passage mode or valid user code entered 80 Series Levers (Shown on pages 7 and 8) 17-3/8" (441mm) 17" (431mm) 17-3/8" (441mm) 17" (431mm) PG Exit Device Functions Escutcheons A multi-colored LED indicates valid/invalid entries Solid diecast zinc Keys/buttons are silk screened on backside to eliminate wear Operating temperature 40 F (-40 C) to 135 F (57 C) Projection at top 1-5/8" (41mm) Mortise Lock Exit If the lock needs to have: Technology Series Type & Function Technology Series Type & Function Outside ET Lever Control Brass escutcheon Projection 13/16" (21mm) Rim Exit Magnetic Stripe only Key override PG 8977 PG 8877 No key override PG 8978 PG 8878 Magnetic Stripe & Keypad Key override KP- PG 8977 KP- PG 8877 No Key override KP- PG 8978 KP- PG /16" (205mm) " (46mm) Options Technology Series Type Function Rail Size ET Trim/ Lever Finish Hand Door Width Select from pages 10 KP-PG- Shown Select from PG Exit Device Function chart above 9" (228mm) Inside How to Order: Exit Devices 3-3/4" (95mm) E: 24-32"; F: 33-36"; J: 37-42"; G: 43-48" 3-3/4" (95mm) 8-3/4" (222mm) Outside ET followed by lever designation from pages 7-9 Select from page 6 RHR or LHR ETL Shown If supplied, rails will be cut to size Example: KP-PG-8878 F ETL 03 RHR 34" 5

8 Finishes, ET Trim and Handing Finishes SARGENT offers many different finishes for P1 products. Please reference the chart below for finishes available. Finishes ANSI Mortise Cylindrical Exit Devices 03 Bright brass 605 X X X 04 Satin brass 606 X X X 09 Bright bronze 611 X X X 10 Satin bronze, clear powder 612 X X X 10B Oxidized satin bronze oil rubbed 613 X X X 10BL Oxidized satin bronze, clear power coat X X X 14 Bright nickel, clear coated 618 X X X 15 Satin nickel, clear coated 619 X X X 20D Dark statuary bronze, clear powder coat X X X 26 Bright chrome 625 X X X 26D Satin chrome 626 X X X 32 Bright stainless steel 629 X X 32D Satin stainless steel 630 X X ET Lever Trim for Exit Devices 8-1/16" (205mm) 1-13/16" (46mm) 3-9/16" MAX (90mm) The 700 Series ET and Lever Control is the external trim with all P1-80 Series exit devices ET Escutcheons and levers are plated brass Stainless steel levers are available 13/16" (21mm) Note: Exit devices are only available with ET Trim Exit Devices ordered in 32 or 32D will have the ET trims supplied in 26 or 26D; for nickel finished ET trims, specify 14 or 15 finish and the exit will be supplied in 32 or 32D accordingly Handing LH Outside Left Hand Door LHR Outside Left Hand Reverse Door RH Right Hand Door RHR Right Hand Reverse Door Outside Outside 6

9 Standard and Coastal Series Levers, Rose and Thumbturn Designs products are available with the following identified lever designs to provide uniformity throughout a facility. Lever projection from door surface varies with lock type. PG mortise locks and cylindrical locks are specified by rose design followed by the lever designation (e.g., TRP). Passport 1000 PG 80 Series Exit Devices are specified by the ET designation followed by the lever designation (e.g., ETP). Levers Standard Levers Coastal Levers Lever Design Handed Mortise Cylindrical Exit Devices Lever Design Handed Mortise Cylindrical Exit Devices A Yes X X C X X B X X X G Yes X X E X X F X X J X X X L X X X P X X X R X X S Yes X X Y Yes X X X Note: PG-8200 mortise locks with Coastal Series levers are available with CR & TR roses (Not available with LN, O, CO & TO roses) W X X Note: PG-8200 mortise locks with standard levers are available with LN and O roses only (not available with CO, CR, TO & TR roses) Roses Roses Design Diameter Mortise LN 2" X CR 2-3/16" X TR 2-3/16" X O 2-3/4" X E2 2-11/16" X Cylindrical Roses Design Diameter Mortise E3 2-1/16" X CO 2-3/4" X TO 2-3/4" X Thumbturns The thumbturn backplate will match the rose design chosen. The turn desgination must be specified as an option before the lock order string. *The standard thumbturn will be supplied if T1, T2 or T3 are not listed. See page 8 in the 8200 mortise lock catalog for more information. T1 Turn 1-1/2" dia. 38mm T2 Turn 1-1/2" 38mm T3 Turn 1-1/2" dia. 38mm Cylindrical L 3-1/2" X G 3-1/2" X Standard Turn* 1-1/2" dia. 38mm :A 6/30/08 10/19/12 Copyright 2008, Copyright Sargent Manufacturing , Company, Sargent Manufacturing ASSA ABLOY Company, Group company. ASSA ABLOY All rights Group reserved. company. All rights reserved. Reproduction in whole Reproduction or in part in without whole or the in part express without written the permission express written of Sargent permission Manufacturing of Sargent Company Manufacturing is prohibited. Company is prohibited.

10 Studio Collection Levers Studio Collection Levers are available with the 8200 Series Mortise. With Exit Device, the Studio Collection is available with the ET trim creating uniformity throughout a facility. Aventura Series Notting Hill Series Lever Design Handed Mortise Exit Devices Lever Design Handed Mortise Exit Devices MB X X MA*** Yes X X ME X X MQ Yes X X MF X X MT Yes X X NF* X X MM Yes X X MG X X MR*** Yes X X MI X X MY* Yes X X NI* X X MW* X X Centro Levers MC*** X X Odeon Series MN Yes X X MD X X MJ X X MH Yes X X MK Yes X X MS Yes X X MU Yes X X MV Yes X X NS* Yes X X NU* Yes X X MX* Yes X X Rialto Series MO Yes X X MZ* Yes X X MP X X ND* X X NJ* X X Gramercy Levers** RCM X X RAL X X REM X X RAM X X RAS X X RAW X X RAG X X * Lever returns within 1/2" (13mm) of door face ** Gramercy levers are customized. Refer to page 9 for ordering information. ***Contact factory for current lead times 8 RGM X X

11 Ordering Gramercy Series Levers Gramercy Series Levers REM, RGM RCM RAG, RAL, RAM, RAS, RAW Gramercy Finish Codes BHMA Finish SARGENT Finish Gramercy Code* Description D 30 Satin Stainless Steel Bright Stainless Steel N/A N/A BH Birch (wood insert) N/A N/A BK Black (Santoprene or leather insert) N/A N/A BN Brown (leather insert) *Code used to specify Gramercy Series finishes only. Use available finishes list to specify desired finish when ordering. Gramercy Lever Descriptions & Available Finishes Lever Designation Lever Description Available Finishes (AS ORDERED) RAG Grooved Insert 2929 or 3030 RAL Leather Insert 29BK, 29BN or 30BK, 30BN RAM Metallic Insert 2930** only RAS Santoprene Insert 29BK or 30BK RAW Wood Insert 29BH or 30BH RCM Raised Band 2929, 3030 or 2930** REM Plain 2929 or 3030 RGM Two Grooves 2929 or 3030 **Two-tone finish - grip of lever is 32D, balance of lever is 32. Rose/escutcheon and lock finish will be 32. To order Gramercy Series levers with SARGENT products, see the examples below. When specifying finish, use the last two digits of the BHMA standard finish code, i.e. use 29 for polished stainless, BHMA finish 629. How to Order: PG-- Mortise Lock with Gramercy Levers Options select from page 10 Technology KP- Series/ Type PG-82 Function Rose Lever Finish Hand select from page 3 select from below Leather insert Bright stainless steel with brown leather RHR, RH, LHR, or LH SG- KP- PG LN RAL 29BN RH How to Order: PG- Exit Device x Gramercy Levers Options Technology Series Type Function Rail Size Trim Lever Finish select from page 10 Select from 80 Series Exit Device Function chart from page 5 E, F, J or G ET Series Leather insert Bright stainless steel with brown leather Inside Finish select from page 6 SG- KP- PG F ET RAL 29BN 32D 36" 9 Door Width

12 Access Control Products Prefixes Mechanical Options Add Strength 3- Stainless steel hubs for institutional specifications (mortise locks only) Fire Rated 12- UL Fire Label Exit hardware (exit devices only, not available with 16- & HK-) Cylinder Dogging 16- Cylinder lockdown (non-fire rated exit devices only) LD- Less hex key dogging (non-fire rated exit devices only) Less Touch Pad 19- Pushbar without Lexan touchpad (exit devices only) 10 Line Backsets /4" Backset x 2-1/4" x 1-1/8" Front (10 Line only) 25-5" Backset x 2-1/4" x 1-1/8" Front (10 Line only) Strike Options /8" (124mm) ANSI flat lip strike (8900 mortise lock exit device & mortise locks only) /8" Strike #808. Lip length 1-1/4" (10 Line only) OBS- WBS- Open Back Strike (for & only) Wrought Box Strike (Not available for 80 series) Security Fasteners 36- Six lobe security head screws 37- Spanner head screws 3/4" Latch Throw 41-3/4" (19mm) throw latch x 2-3/4" (70mm) backset (10 Line only) Flush End cap 43- Flush End Cap (exit devices only) Tactile Warning Options 75- Tactile Warning - Milled Inside Lever (Not available with Exit Devices, Studio & Coastal Levers and the A Lever) 76- Tactile Warning - Milled Outside Lever (Not available with Studio & Coastal Levers and the A Lever) 77- Tactile Warning - Milled Inside & Outside Lever (Not available with Exit Devices, Studio & Coastal Levers and the A Lever) 85- Tactile Warning - Abrasive Coating on Inside Lever (or Push Rail for Exits) 86- Tactile Warning - Abrasive Coating on Outside Lever 87- Tactile Warning - Abrasive Coating on Outside Lever & Inside Lever (or Push Rail for Exits) Hard Power 91- Hard power (requires external 3267 power supply) Finish Protection CPC- Clear Powder Coat (Available for 26, 26D, 32 & 32D Finishes) SG- MicroShield antimicrobial clear powder coat SARGuide PL- SARGuide PL Photoluminescent Coated Push Rail (Touchpad eliminated) (Not available 75-, 77 & TL-) Hurricane-Resistant exit devices HC- Hurricane Code (rim exit devices only, see page 16 for details) Degree Key System DG1-60- SARGENT Degree Key System Level 1 Removable Disposable Construction Core (not available with cylindrical locks) DG2-60- DG3-60- SARGENT Degree Key System Level 2 Removable Disposable Construction Core (not available with cylindrical locks) SARGENT Degree Key System Level 3 Removable Disposable Construction Core (not available with cylindrical locks) XC- Large Format Interchangeable Core Hardware to accept XC- Permanent LFIC (Removable Core), Disposable plastic Core- provided XC-Interchangeable Cores P- Hardware to accept XC- SFIC ( 7-Pin) XC- Permanent Cores, plastic disposable core provided (10 Line J lever not available) Large Format Interchangeable Core 60- Hardware to accept SARGENT Permanent LFIC (Removable Core), Disposable Plastic Core provided (Permanent Cores ordered separately) Interchangeable Cores 70- Hardware to accept 6 or 7-Pin SFIC Permanent Cores, Plastic Disposable Core provided (10 Line J lever not available) Keso & Keso F1 81- Hardware provided with housings to accept Keso (83) & Keso F1 (F1-83-) removable cores (Not available with 10 Line) (Permanent Cores ordered separately) Less Cylinder LC- Hardware supplied less cylinder WS- Accept Schlage Cylinders 30- Lever to accept Schlage Cylinder-Cylinder is not provided (10 Line only) SF- Windstorm Rated (rim & mortise lock exit devices only, see page 16 for details) Thumbturns T1- Decorative thumburn; backplate matches rose design chosen Cylinder Options T2- Decorative square thumburn; backplate matches rose design chosen T3- Decorative cylinder thumburn; backplate matches rose design chosen L Lever to accept Medeco KeyMark Large Format Interchangeable and Schlage Full Size Interchangeable Core (10 Line only) Schlage Keyways SC- Schlage C keyway cylinder, 0 bitted (Not available with 8900 Series exit devices) 10 SE- Schlage E keyway cylinder, 0 bitted (Not available with 8900 Series exit devices)

13 Access Control Products Architectural Specifications PG-10 Line Bored A. PG-10 Line Series Bored ets Card Key Access Control Bored. 1. Card Key access control Bored to be 10-Line Series as manufactured by SARGENT manufacturing of New Haven, CT. 2. BHMA certified extra heavy duty, lever type Bored Lock conforming to ANSI Series 4000, Grade 1 standard and ANSI A117.1 accessibility guidelines. Motorized locking control with ½ anti-friction deadlocking latch UL listed and labeled for up to 3 hour fire-rated openings. - Backset: 2 ¾ inches 3. able to read, analyze and control access to level of authorization encoded on keycard with adjustable reader heads providing flexibility to read designated track based on varied thickness of keycards. - Access by magnetic stripe card insertion and keypad pin number or by magnetic stripe card insertion only. Lock responds upon keycard removal ensuring that keycards are not left in the lock. - Card track: Track 1 or 3 4. Emergency overrides access capability through system-generated special access keycards and keypad codes, which are time, date and location specific. - Mechanical key override capability of latch from outside with no electronic activation necessary on any level keycard, keypad code or mechanical key. 5. Inside lever retracts latchbolt. 6. to be water resistant on external installation AA alkaline batteries power supply with LED indication of locked, programming mode and low capacity warning status conditions. 8. Provide PERSONA Campus 1000 Software compatible with Microsoft Windows operating systems (2000/XP) with support of a maximum 1,200 users and recoverable date and time audit trails up to last 700 events. 9. Cylinders: Reference 2.04 Keying for keying requirements. PG-8200 Series Mortise A. PG-8200 Series Mortise ets Card Key Access Control Mortise. 1. Card Key access control Mortise to be 8200 Series as manufactured by SARGENT manufacturing of New Haven, CT. 2. BHMA certified extra heavy duty, lever type Mortise Lock conforming to ANSI Series 1000, Grade 1 standard and ANSI A117.1 accessibility guidelines. Motorized locking control with ¾ anti-friction deadlocking latch and 1 hardened stainless steel deadbolt. UL listed and labeled for up to 3 hour fire-rated openings. 3. able to read, analyze and control access to level of authorization encoded on keycard with PG-8800/8900 Series Exit Devices A. PG-8800/8900 Series Rim and Mortise Exit Devices Card Key Access Control Rim and Mortise Exit Devices 1. Card Key access control Exit Devices to be 80 Series as manufactured by SARGENT manufacturing of New Haven, CT. 2. BHMA certified panic and exit device hardware conforming to ANSI 156.3, Grade 1 standard and ANSI A117.1 accessibility guidelines. U.L. listed for either panic or as Fire Exit Hardware for up to 3 hour fire-rated openings. adjustable reader heads providing flexibility to read designated track based on varied thickness of keycards. - Access by magnetic stripe card insertion and keypad pin number or by magnetic stripe card insertion only. Lock responds upon keycard removal ensuring that keycards are not left in the lock. - Card track: Track 1 or 3 4. Monitoring: Emergency cylinder, deadbolt and auxiliary latch. 5. Emergency overrides access capability through system-generated special access keycards and keypad codes, which are time, date and location specific. - Mechanical key override capability of latch and deadbolt from outside with no electronic activation necessary on any level keycard, keypad code or mechanical key. 3. Motorized locking and unlocking of the lever contained in the body of the outside trim control. Provide lever design to matching lock lever design. 4. able to read, analyze and control access to level of authorization encoded on keycard with adjustable reader heads providing flexibility to read designated track based on varied thickness of keycards. - Access by magnetic stripe card insertion and keypad pin number or by magnetic stripe card insertion only. Lock responds upon keycard removal ensuring that keycards are not left in the lock. - Card track: Track 1 or 3 5. Emergency overrides access capability through system-generated special access keycards and keypad codes, which are time, date and location specific. 6. Inside lever retracts latchbolt and deadbolt simultaneously. 7. to be water resistant on external installation AA alkaline batteries power supply with LED indication of locked, programming mode and low capac ity warning status conditions. 9.Provide PERSONA Campus 1000 Software compatible with Microsoft Windows operating systems (2000/XP) with support of a maximum 1,200 users and recoverable date and time audit trails up to last 700 events. 10.Cylinders: Reference 2.04 Keying for keying requirements. - Mechanical key override capability of latch from outside with no electronic activation necessary on any level keycard, keypad code or mechanical key. 6. Provide keyed cylinder dogging feature for non-rated panic devices and keyed removable mullions as specified in the Hardware Groups. 7. to be water resistant on external installation AA alkaline batteries power supply with LED indication of locked, programming mode and low capacity warning status conditions. 9. Provide PERSONA Campus 1000 Software compatible with Microsoft Windows operating systems (2000/XP) with support of a maximum 1,200 users and recoverable date and time audit trails up to last 700 events. 10. Cylinders: Reference 2.04 Keying for keying requirements. 11

14 SARGENT Manufacturing Company 100 Sargent Drive, New Haven, CT USA PERSONA Technical Support: Founded in the early 1800s, SARGENT is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company s customer base includes commercial construction, institutional, and industrial markets. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience :A 10/2012