Fisherr HP Series Control Valves

Transcription

1 HP Valve Product Bulletin Fisherr HP Series Control Valves HP (Globe Valve) HPA (Angle Valve) Balanced High-Temperature Trim Balanced Tight Shutoff Trim Unbalanced Trim Fisher HP Series control valves are single-port, high-pressure, globe- or angle-style valves with metal seats, cage guides, and push-down-to-close valve plug action. These valves are designed for high-pressure applications in process control industries such as power generation, hydrocarbon production, chemical processing, and refining. HP Series valves are designed with corrosion allowance; NACE compliant materials are available. Extra valve body wall thickness provides asafety margin of protection against erosion, as well as extra protection against corrosion due to chemical attack. Because these valves feature a thicker valve body wall, they are available in higher intermediate ratings with weld-end fittings. Unless otherwise noted, all NACE references are to NACE MR and MR003. Balanced High-Temperature Trim HPD These valves use a balanced valve plug with graphite piston rings and are well suited for general applications with process temperatures in excess of 232_C (450_F), where extremely tight shutoff is not required. X083- FISHER HP VALVE WITH 667 ACTUATOR AND FIELDVUE DVC6200 DIGITAL VALVE CONTROLLER Balanced Tight Shutoff Trim HPT and HPAT These valves use a balanced valve plug and offer excellent shutoff with process temperatures below 232_C (450_F). The temperature limits of HPT can be extended above 232_C (450_F) to 36_C (600_F) by using PEEK (PolyEtherEtherKetone) anti-extrusion rings in combination with aspring-loaded PTFE seal. The PEEK anti-extrusion rings expand to help close off the clearance gaps on the plug outside diameter and the cage inside diameter where the PTFE seal may extrude at high temperatures and pressures.

2 Product Bulletin HP Valve Specifications Available Configurations () and Valve Sizes See table Common s: Designed according to: J ASME B6.34 Valve-Flanges, Threaded and Welding End and J ANSI/ISA End Connections Styles () See table Maximum Inlet Pressure and Temperature (,2) Flanged, Socketwelding, or Buttwelding: Consistent with CL900, 500, and 2500 according to ASME B6.34, unless limited by maximum pressure drop or material temperature capabilities In addition, both steel HP and HPA valves with BWE and SWE connections have increased pressure/temperature ratings as shown in table 3 Maximum Pressure Drop () Valve with Standard Cage: Seefigure2. Valve with Cavitrol III Cage: 49 bar (260 psi) for two-stage and 207 bar (3000 psi) for three-stage cage. Consult Fisher Bulletin 80.2:030, Cavitrol III One-,Two-,andThree-Stage trims, for more information Valve with Whisper Trim III Cage: J 0.6 np/p maximum for levels A and A3 J np/p maximum for levels B and B3 J 0.85 np/p maximum for levels C and C3 J 0.99 np/p maximum for levels D and D3 Valve with WhisperFlo Trim: J Levels X, Y, and Z: 0.94 np/p maximum. If greater than 0.94 np/p, consult your Emerson Process Management sales office Shutoff Classifications See table 4 chrome-molyalloy,j CF8M stainless steel, and J LCC for low temperature service Trim: See table 2 Other Parts: Seetable7 Consult your Emerson Process Management sales office for special trim and valve body material availability. Material Temperature Capabilities () HPD, HPS, and HPAS: Up to 566_C (050_F) unless limited (see tables 7 or 2 and figure 2) HPT and HPAT: Up to 232_C (450_F) unless limited (see tables 7 or 2 and figure 2) Flow s (4) Standard Cages: J, J equal percentage, J modified equal percentage (5) Cavitrol III and Whisper Trim III Cages: Micro-Flute: Equal percentage Micro-Flat: Micro-Form: J Equal percentage, J modified equal percentage Flow Direction Standard Cage J HPD: Normally flow down J HPS, HPAS: Normally flow up (6) J HPAS Micro-Flat: Flow down J HPS, HPAS Micro-Form: Flow up only J HPT, HPAT: Normally flow down Cavitrol III Cage: Flow down Whisper Trim III Cage: Flow up Flow Coefficients See table 2, the section titled Coefficients in this bulletin, and also Catalog 2 Noise Levels See Catalog 2, Section 3 for noise prediction methods Construction Materials Valve Body and Bonnet: J WCC steel (3), J WC9 Cr-Mo steel (3), J C2A - continued - Port Diameters, Valve Plug Travel, and Stem Diameters Seetables5,8,9,and 2

3 HP Valve Product Bulletin Specifications (continued) Bonnet Style and Mounting () J Standard Bonnet: Seefigure Yoke Temperature Limit: Standard bonnet with cast iron yoke is limited to 537_C (000_F) J Optional Style Extension Bonnet: Used for and 2 valves for CL900 or 500, and valves for CL2500 (see figures 4 and 5) Packing Arrangements J Single, J Double, and J Leakoff standard packing, or optional J ENVIRO-SEAL and J HIGH-SEAL packing systems. See figure 4. Also see bulletin 59.:06, ENVIRO-SEALandHIGH-SEAL Packing Systemfor Sliding-Stem Valves Yoke Boss Diameter for Actuator Mounting See tables 5 and 0, and figures 3, 4, and 5 Approximate Weight See table 6. The pressure/temperature limits in this bulletin and any applicable standard limitations should not be exceeded. 2. EN (or other valve body material) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office. 3. SA-05 and SA-82-F22 are used for CL2500 HPA valves instead of WCC and WC9. 4. Special characterized cages are available. Contact your Emerson Process Management sales office. 5. Modified equal percentage characteristic is equal percentage for the first 75% of travel, then opens quickly for additional capacity. 6. HPS valves may be used flow down for on-off service only. HPAS valves may be used for flow down in erosive service. 7. For more information contact your Emerson Process Management sales office. 8. Required for all boiler feedwater applications. Options () J Valves with weld-end fittings have increased pressure/temperature ratings, called intermediate ratings (7), J Class V (6) shutoff for HPT to 36_C (600_F) using PEEK anti-extrusion rings (8), J Class V shutoff for HPD to 593_C (00_F) using C-seal trim, J expanded ends (7) for4and6valves(4 valves are available with 6 ends, and 6 valves are available with 8 ends), J lubricator or lubricator/isolating valve (7) Table of Contents Balanced High-Temperature Trim... Balanced Tight Shutoff Trim... Specifications... 2 Unbalanced Trim... 4 Expanded Ends... 4 Cavitrol, Whisper Trim and WhisperFlo Cages... 4 Features... 4 Material Selection Guidelines... 7 Installation... 7 Packing... 9 Trim Selection Guidelines... 5 Trim Material Combinations... 7 Pressure/Temperature Limits for Trim Material Combinations... 8 Dimensions... Coefficients

4 Product Bulletin HP Valve Figure. Fisher HPD Valve Assembly ( 2 to 6) Cavitrol III, Whisper Trim III, and WhisperFlo Cages To eliminate cavitation damage in a properly-sized valve, a Cavitrol III cage is available with HPS, HPAS, HPT, and HPAT control valves. To help attenuate aerodynamic noise in gaseous service, Whisper Trim III and WhisperFlo (figure 2) cages are available with HPD, HPS, HPAS, HPT, and HPAT control valves. Contact your Emerson Process Management sales office for more information. FLOW W585A- Figure 2. Typical WhisperFlo Trim Cut Section View forfisherhpvalve W7065 Features Valve Plug Stability Rugged cage guiding provides increased valve plug stability, which reduces vibration and mechanical noise. Full Pressure Drop Capability Rugged construction allows full pressure drop capability in HP series valves. Spiral-Wound Gaskets for Excellent Sealing Under All Service Conditions Premium materials are used in the construction of spiral-wound gaskets for HP Series valves. These premium materials, which make up the standard spiral-wound gaskets, are N06600 (alloy 600)/graphite or N07750 (alloy X750)/graphite. Unbalanced Trim HPS and HPAS These valves have an unbalanced plug and provide excellent shutoff. Expanded Ends Expanded ends are available on the 4 and 6 CL900 and 500 HP valves. The 4 HP valve body is offered with 6 ends. The 6 valve body is offered with 8 ends. Both flanged and buttweld end valve bodies are offered with expanded ends. Compliance with the Clean Air Act Optional ENVIRO-SEAL packing systems (figure 4) provide an improved stem seal to help prevent the loss of valuable or emission of hazardous process fluid. The ENVIRO-SEAL packing systems feature PTFE or graphite ULF. Piping Economy The availability of expanded end connections on 4 and 6 HP valves may eliminate the need for line swages while accommodating oversized piping arrangements. Quick Change Trim Maintenance is simple and can easily be performed using common tools. Trim components can be quickly removed and changed with no need for special tools. Standard Hard Trim Materials Thecage,valveplug, and other trim parts are manufactured from 4

5 HP Valve Product Bulletin hardened materials. This standard feature provides excellent wear resistance. Control of Low Flow Rates/Tight Shutoff Micro-Flute and Micro-Formvalveplugs (figures 6 and 7, respectively) provide superb rangeability in high-pressure, low-flow applications, while maintaining tight shutoff (table 4). A choice of several restricted port diameters helps to match valve body capacity to required flow, to provide necessary control with full travel, and to prevent throttling near the seat. In low-flow applications where cavitation damage may occur, the Micro-Flat valve plug can be used with a special Cavitrol III cage. Contact your Emerson Process Management sales office for more information. Increased Pressure/Temperature Ratings HP Series valves with weld-end fittings have increased pressure/temperature ratings, called intermediate ratings, as defined in ASME B6.34. The extra strength of these valves allows ratings higher than the standard CL900 or 500 ratings specified in B6.34. Contact your Emerson Process Management sales office for further information on intermediate ratings. Trim Interchangeability Cavitrol III, Whisper Trim III, and WhisperFlo trims (figures 8, 9, and 0) are interchangeable with standard trims. Smooth Control at High Pressure Drops Available on 2 through 6 valves, balanced trim provides smooth control at high pressure drops. High-Temperature Capability with Class V Shutoff Use of C-seal trim (see figure 5) permits Class V shutoff up to 593_C (00_F) for HPD valves. Sour Service Trims Available Long-lasting, erosionand corrosion-resistant trims are available for control of sour service. These trims are offered with either a standard cage, a Cavitrol III cage, a Whisper Trim III cage, or WhisperFlo trim. Spiral-wound gasket construction is standard. Table. Available Constructions DESIGN VALVE SIZE, PRESSURE RATING WCC, WC9, LCC, and C2A Cast Steel Valves RF or RTJ Flanged, Butt Weld, and Socket Weld (3) VALVE BODY MATERIAL AND END CONNECTION STYLE (, 2) CF8M (36 Stainless Steel) Valves RF or RTJ Flanged and Socket Weld (3) SA-05, SA-82-F22, and SA-82-F36 forged SST (for forged steel HPA CL2500 angle valves) Socket Weld HPAS to2 CL900 and 500 X X --- CL X HPAT to2 CL900 and 500 X X --- CL X HPD 2to6 CL900 and 500 X X CL2500 X X --- HPS to3 CL900 and 500 X X --- to2 CL2500 X X --- HPT 2to6 CL900 and 500 X X CL2500 X X --- X = Available Construction.. End connection style abbreviations: RF - Raised Face, RTJ - Ring Type Joint. 2. EN (or other valve body material) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office. 3. Socket Weld available on, -/2, and 2 only. 5

6 Product Bulletin HP Valve Table 2. Typical Flow Coefficients () Valve Size, Valve Style Maximum Cv HP Modified Equal Percentage HP HP 27 4 HP 20 6 HP 425 HPA CL500 Modified Equal Percentage 7 2 HPA CL HPA CL2500 Modified Equal Percentage HPA CL See the section titled Coefficients in this bulletin and also Catalog 2 for a complete listing of flow coefficients. Table 4. Shutoff Classifications per ANSI/FCI 70-2 and IEC HPD w/ C-seal trim Table 3. Increased Pressure/Temperature Ratings for Steel Valves with BWE and SWE Connections () Valve Type Valve Size, Intermediate Rating Pressure Rating (ASME B6.34) CL900 and CL Globe Valves 2 CL900 and CL CL CL Contact your Emerson Process Management sales office for further information on intermediate ratings. Valve Design Port Diameter, mm (Inches) ANSI/FCI and IEC Leakage Class 47.6 (.875) II HPD 58.7 (2.325) to 92. (3.625) II - Standard III - Optional. (4.375) and larger III - Standard IV - Optional Valve Size, Port Diameter, mm (Inches) Cage Style ANSI/FCI and IEC Leakage Class Eq.%,Mod.Eq.%, 3 73 (2.875) (std. cage), (Whisper III, A, B) 73 (2.875) (Whisper III, D3) V - Standard (Cav III, 3-stage) to 593_C (00_F) (3.4375) (Cav III, 2-stage) (for port diameters from 73 mm [2.875 inch] through 36.5 mm [5.375 inch] 92. (3.625) with optional C-sealtrim) HPS, HPAS, HPT, HPAT HPS and HPT w/ TSO (Tight Shutoff trim) 6 HPT and HPAT w/ PEEK () Anti-Extrusion Rings. (4.375) 36.5 (5.375) All Eq.%,Mod.Eq.%, (std. cage), (Whisper III, A, B3, C3) (Whisper III, D3), (Cav III, 3-stage) Eq.%,Mod.Eq.%, (std. cage), (Whisper III, A, B3, C3), (Cav III, 2-stage) Cavitrol III and Micro-Flat Micro-Form, Micro-Flute,Eq. %, ModEq.%,,WhisperIII See table 5 See table (.875) to 36.5 (5.375) All. PEEK (PolyEtherEtherKetone), required for all boiler feedwater applications. IV - Optional (for port diameters 73 mm [2.875 inch] through 36.5 mm [5.375 inch] V - Standard IV - Standard V - Optional TSO - Optional TSO is not an ANSI/FCI or IEC leakage class. Valves with TSO trim are factory tested to a more stringent Fisher test requirement of no leakage at time of shipment. Test medium is water. Specify service Pwhenordering. Test procedure is ANSI/FCI Class V test procedure B V - Standard (to 36_C [600_F]) IV - Optional (47.6 mm [.875 inch] through 36.5 mm [5.375 inch] ports) 6

7 HP Valve Product Bulletin Material Selection Guidelines Use the following steps as a guideline for the selection of materials:. Determine the pressure/temperature rating of the valve body size and material required. Inlet pressure and temperature must always be limited by the applicable ASME pressure/temperature rating. 2. Select the desired trim style from the Available Configurations specification and from table 4, Shutoff Classifications. 3. Select desired materials from tables 7, 8,, and 2 and figure 2. The temperature capabilities determined from figure 2 may be further limited by the temperature capabilities of materials selected from tables 7 and 2. Refer to figure 2 to determine pressure drop limits of the valve body-trim combinations selected. 4. Select the appropriate spiral-wound gasket material. N06600 is recommended for service up to 427_C (800_F). N07750 is recommended for service over 427_C (800_F) when improved corrosion resistance is required or when the valve is subject to severe temperature cycling service. Installation The valve must be installed so flow through the valve is as indicated by the flow direction arrow on the valve body. Consideration should be given to installing an upstream strainer, especially if the valve uses a Cavitrol III cage, Whisper Trim III, or WhisperFlo trim. Overall dimensions are shown in figures 3, 4, and 5. Face-to-face dimensions are in compliance with ANSI/ISA Actual end connection dimensions conform to ASME B6.25 for buttwelding ends and to ASME B6.5 for flanged ends. Figure 3. Typical Balanced TSO Trim VALVE PLUG SEAL W7020- TSO PROTECTED SOFT SEAT SEAL 7

8 Product Bulletin HP Valve Table 5. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) Trim VALVE TYPE TRIM PORT DIAMETER C V UNBALANCE MAX TRAVEL YOKE BOSS SIZE REDUCTION Nominal Actual TSO AREA AT 00% mm Inch mm Inch mm Inch mm Inch TRAVEL () Inch 2 Balanced Plugs Flow Down Only HPT 3 (2) CAV III 3-Stage / % 0.03 HPT 4 HPT 6 CAV III 3-Stage CAV III 3-Stage 02 4 Standard / / / % % % Unbalanced Plugs Flow Down Only HPS CAV III 3-Stage / % This column lists the percent reduction of published maximum C V of the trim listed in the TRIM column. 2. Not available with 5-inch yoke boss. 8

9 HP Valve Product Bulletin Figure 4. ENVIRO-SEAL and HIGH-SEAL Packing Systems PACKING BOX STUD PACKING BOX STUD SPRING SPRINGS PACKING FOLLOWER PACKING FOLLOWER W8533- TYPICAL HIGH-SEALPACKING SYSTEM WITH GRAPHITE ULF PACKING W8532- TYPICAL ENVIRO-SEAL PACKING SYSTEM WITH GRAPHITE ULF PACKING PACKING BOX STUDS SPRINGS ANTI- EXTRUSION RING PACKING RING LANTERN RING VALVE BONNET W TYPICAL ENVIRO-SEAL PACKING SYSTEM WITH PTFE PACKING 9

10 Product Bulletin HP Valve Table 6. Approximate Weights (Valve and Bonnet Assemblies) VALVE SIZE, KILOGRAMS POUNDS VALVE TYPE PRESSURE RATING Flg SWE, BWE Flg SWE, BWE CL900 and CL /2 x 2 CL CL900 and CL Globe Valves CL CL CL CL CL CL CL900 and CL () () Angle Valves CL900 and CL () (). Only SWE is available for CL2500. Figure 5. C-seal Trim C-SEAL METAL PLUG SEAL () C-SEAL METAL PLUG SEAL () FLOW DOWN FLOW UP VIEW A 37B399-A NOTES. REVERSE THE ORIENTATION OF THE C-SEAL PLUG SEAL FOR PROPER SHUTOFF WHEN VALVE IS USED IN A PROCESS WITH DIFFERENT FLUID FLOW DIRECTION. 0

11 HP Valve Product Bulletin Table 7. Construction Materials and Temperature Capabilities for Parts Other than Valve Body and Trim PART MATERIAL TEMPERATURE CAPABILITIES Valve plug stem S to to 00 HPD piston ring Graphite (FMS 7F27) Graphite (FMS 7F39) _C -254 to 427 (to 482 for nonoxidizing service) -254 to 537 (to 593 for nonoxidizing service) _F -425 to 800 (to 900 for nonoxidizing service) -425 to 000 (to 00 for nonoxidizing service) Backup ring S4600 (46 SST) -29 to to 800 S3600 (36 SST) -8 to to 00 Spring-loaded S30200 (302 SST) Retaining ring HPT or HPAT N07750 (NACE) -254 to to 00 valve plug seal Seal ring PTFE with N0276 Spring -73 to 232 (5) -00 to 450 (5) Anti-extrusion rings PEEK (PolyEtherEtherKetone) -73to36-00to600 Cage gasket N06600/Graphite -240 to to 00 TSO protected soft seat seal Carbon-filled PTFE -73 to to 450 Seat ring gasket N06600/Graphite -240 to to 00 Valve Body-tobonnet bolting () Packing Studs Nuts Studs Nuts Studs Nuts Studs Nuts Studs Nuts Studs Nuts Steel SA3-B7 (all valve body materials) Steel SA4-2H (all valve body materials) Steel SA3-B7Mfor sour service Steel SA4-2HMfor sour service Steel SA3-B6 (WC9 and C2A valvebody mat'ls) Steel SA4-7 N0778 SST (SB637) (3) Steel SA to 427 (WCC and WC9) -46 to 37 (LCC) -48 to 427 (36 CF8M) (2) -29 to 427 (WCC) -46 to 37 (LCC) -20 to 800 (WCC and WC9) -50 to 700 (LCC) -55 to 800 (36 CF8M) (2) -20 to 800 (WCC) -50 to 700 (LCC) -29 to to to 566 (WC9) -29 to 593 (C2A) -20 to 050 (WC9) -20 to 00 (C2A) S3600 stainless steelsa3-b8m (strain hardened) (CF8M valve body mat'ls) (4) S3600 stainless steel SA4-8M (CF8M valve body mat'ls) (4) -8 to to 800 S2090 SST (SA479-XM-) (3) (CF8M valve body mat'ls) Steel SA to to 00 PTFE V-ring -46 to to 450 Graphite ribbon filament (oxidizing service to 37_C [700_F]) -254 to to 000 Graphite ribbon (high-temperature oxidizing service) 37 to to 00 Packing follower, spring, or lantern ring S3600 stainless steel -254 to to 00 Packing box ring S3600 stainless steel -254to to00 Packing flange, studs, or nuts Steel -29 to to 800 S3600 stainless steel -8 to to 00. Valve body materials with which these bolting materials may be used are shown in parentheses. 2. Steel studs and nuts with NCF (non-corroding finish) coating are used with 4 and 6 CF8M valve bodies. 3. These stud materials are not listed in ASME B For valve sizes up through 3. 5.Ifused with PEEK anti-extrusion rings,ptfe/carbon seal ring maybeused in temperatures up to 36_C (600_F) for non-oxidizing serviceor up to 260_C (500_F)for oxidizing service.

12 Product Bulletin HP Valve Table 8. Additional Globe Valve Specifications VALVE SIZE, FLOW CHARACTERISTIC Equal percentage Modified equal percentage (cage style: Cavitrol III, 2-stage) Equal percentage (cage style: Std) (cage style: Whisper Trim III, level A) Modified equal percentage (cage style: Cavitrol III, 2-stage) (cage style: Cavitrol III, 3-stage) Modified equal percentage (cage style: Std) (cage style: Whisper Trim III, level A, B) (cage style: Cavitrol III, 2-stage) (cage style: Cavitrol III, 3-stage) Modified equal percentage (cage style: (Std) (cage style: Whisper Trim III level A, A3, B3, C3) (cage style: Whisper Trim III level D3) (cage style: Cavitrol III, 2-stage) (cage style: Cavitrol III, 3-stage) VALVE BODY DESIGN AND PLUG STYLE HPS w/micro-flute HPS w/micro-form HPS w/micro-form PORT DIAMETER VALVE PLUG TRAVEL VALVE STEM DIAMETER mm Inches mm Inches mm Inches ,.,.,. /2 /2 /2 /2 /2 /2, 3/4 /2,3/4 /2, 3/4 HPS ,. /2, 3/4 HPS w/micro-form ,. /2 /2 /2, 3/4 HPS ,., 25.4 () /2, 3/4, () HPS, HPD, HPT ,., 25.4 () /2, 3/4, () HPS w/micro-form ,., 25.4,., 25.4,., 25.4 /2, 3/4, /2, 3/4, /2, 3/4, HPS, HPD, HPT ,., 25.4 () /2, 3/4, () HPT ,. /2, 3/4 HPS /4 HPD, HPT ,.,25.4 /2,3/4, HPT ,., 25.4 /2, 3/4, HPT ,., 25.4 /2, 3/4, HPD, HPT ,25.4 3/4, HPD, HPT ,25.4 3/4, HPT , /4, HPT , /4, -continued- 2

13 HP Valve Product Bulletin Table 8. Additional Globe Valve Specifications (Continued) VALVE SIZE, FLOW CHARACTERISTIC VALVE BODY DESIGN AND PLUG STYLE PORT DIAMETER VALVE PLUG TRAVEL VALVE STEM DIAMETER mm Inches mm Inches mm Inches Modified equal percentage (2) (cage style: Std) (cage style: Whisper Trim III, level A, B3, C3) HPD, HPT HPD, HPT , 25.4, ,3.8 3/4,, -/4,-/4 6 (cage style: Whisper Trim III, HPD, HPT ,3.8,-/4 level D3) (cage style: Cavitrol III, 2-stage) HPD, HPT ,25.4,3.8 3/4,,-/4 (cage style: Cavitrol III, 3-stage) HPD, HPT ,5.4,3.8 3/4,,-/4. Available only with HPS valve. 2. The first 75% is equal percentage. Table 9. Valve Stem Travels for CL2500 Globe Valves VALVE SIZE, VALVE DESIGN / PLUG STYLE HPS / Micro-Form or Micro-Flute 2 HPS / Micro-Form HPS / Micro-Form HPS HPD, HPT CHARACTERISTIC Equal Percentage Modified Equal Percentage Equal Percentage Modified Equal Percentage PORT DIAMETER MAXIMUM VALVE STEM TRAVEL mm Inches mm Inches 6.4, 9.5,,., , 9.5,,., ,., 25.4, ,., 25.4, , 0.375, 0.5,, 0.25, 0.375, 0.5,, 0.25,,, ,,, Equal Percentage Modified Equal Percentage Equal Percentage Modified Equal Percentage Equal Percentage Modified Equal Percentage Table0.GlobeandAngleValveYokeBossand Valve Stem Diameter Combinations () VALVE STANDARD DIAMETERS OPTIONAL DIAMETERS SIZE, mm Inches mm Inches Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss / / /6 3-9/ / / See tables 8, 9, and for valve stem diameters available for specific constructions / /6 3

14 Product Bulletin HP Valve Table. Additional Angle Valve Specifications VALVE SIZE, 2 FLOW CHARACTERISTIC Equal percentage Modified equal percentage (cage style: Std) (cage style: Cavitrol III, 2-stage) Equal percentage Modified equal percentage VALVE BODY DESIGN AND PLUG STYLE FLOW DIRECTION HPAS w/micro-flute Up (2) HPAS w/micro-form Up. HPAS, equal percentagecharacterized cage HPAS w/micro-form Up PORT DIAMETER VALVE PLUG TRAVEL VALVE STEM DIAMETER mm Inches mm Inches mm Inches ,. /2 /2 /2 /2 /2 /2, 3/4 Down.. 3/ ,.,. /2 /2, 3/4 /2, 3/4 HPAS Down /4 HPAS w/ Micro-Flat Down HPAS Down ,. /2, 3/4 HPAS w/micro-flute Up (2) HPAS w/micro-form Up HPAS, equal percentagecharacterized cage Down ,.,., /2 /2 3/4 /2 /2 /2 /2 /2 /2, 3/4 /2, 3/4, 3/4 3/4 HPAS Up ,., 25.4 /2, 3/4, HPAT Down ,. /2, 3/4 HPAS w/micro-form HPAS, equal percentagecharacterized cage Up Down ,., 25.4,., 25.4,., /2, 3/4, /2, 3/4, /2, 3/4, 3/4 3/4 HPAS Up ,., 25.4 /2, 3/4, HPAT Down ,. /2, 3/4 (cage style: std) HPAS w/micro-flat Down /4 (cage HPAS Up ,., 25.4 /2, 3/4, style: std) HPAT Down ,. /2, 3/4 (cage style: Whisper III, level A) HPAS, HPAT Up ,., 25.4 () /2, 3/4, () (cage style: Cavitrol III, 2-stage) HPAT Down ,. /2, 3/4 (cage style: Cavitrol III, 3-stage) HPAS Down /4. Available only with HPAS valves. 2. Micro-Flutes ( flute and 0.5 inch port 2 flute) may be used flow down in flashing and erosive service. 4

15 HP Valve Product Bulletin Figure 6. Fisher HPS Trim with Micro-Flute Valve Plug Figure 7. Fisher HPS Trim with Micro-Form Valve Plug W586- FLOW W587- FLOW Trim Selection Guidelines Refer to the following descriptions as a guideline for the selection of appropriate trims. Trims 204, 202, and 203 should not be used in boiler feedwater due to amine corrosion problems associated with CoCr-Aand R30006 (alloy 6). Trim 20 Trim 20 is the standard trim for carbon steel and alloy steel valve bodies. Trim 20A, with an S4600 (46 stainless steel) heat-treated seat ring, is recommended for general and severe service applications up to 427_C (800_F) for the and 2 valve size and up to 343_C (650_F) for the 3 through 6 valve size. Typical applications for Trim 20 include services in boiler feedwater (Trim 20A only), water, non-sour hydrocarbons, and steam. The S4600 heat-treated plug and seat ring have a minimum hardness of 38 HRC (Rockwell C), as compared to CoCr-A with a minimum hardness of 36 HRC. Trim 204 Trim 204 should be used for sour service or moderately corrosive service. Standard stem material, S2090 meets the metallurgical requirements of NACE MR Trim204 should not be used in boiler feedwater service if amine problems exist. Trim 202 Trim 202 is designed primarily for use in all high temperature applications between 427_C (800_F) and 566_C (050_F), but can also be used between -29_C(-20_F) and 427_C (800_F). Not for boiler feedwater use if amine problems exist. Trim 202 is recommended for use in 6 valves between -29_C(-20_F) and 343_C (650_F). Trim 202H is recommended for use in 6 valves between 260_C (500_F) and 566_C (050_F). Trim 203 Trim 203 is the standard trim for stainless steel valve body materials and should only be used with stainless steel valve body materials. Not for boiler feedwater use if amine problems exist. Trim 2 Trim 2 is the standard trim for C2A valve body materials and should only be used with C2A valve body materials. C2A should only be used when the pressure and temperature capabilities for WC9 valve body materials are not acceptable. 5

16 Product Bulletin HP Valve Figure 8. 2 Fisher HPS Trim with Cavitrol III 3-Stage Cage Figure 0. Fisher HPD Trim with Whisper Trim III Level D Cage (also available in HPT and HPS) W588- FLOW W595- FLOW Figure 9. Fisher HPT Trim with Whisper Trim III Level A Cage (also available in HPD [ 2-6] and HPS [ 2 and 3]) Figure. Fisher HPAS Trim with Micro-Flat Valve Plug W602- W5952- FLOW FLOW C-seal Trim Description C-seal trim is available for HPD valves with port diameters from inches through inches. With C-seal trim, abalancedvalvecan achieve high-temperature, Class V shutoff. Because the C-seal plug seal is formed from metal (N0778 nickel alloy) rather than an elastomer, a valve equipped with the C-seal trim can be applied in processes with a fluid temperature of up to 593_C (00_F). Fisher TSO (Tight Shutoff) Trim Capabilities TSO trim is available for HPS and HPT valves with port diameters as defined in table 5. Also see figure 3 and table 4. TSO trim consists of a protected soft seat plus PEEK anti-extrusion rings with a spring-loaded PTFE plug seal. Used only in flow down applications, TSO trim offers unparalleled shutoff integrity, resulting in longer plug and seat life. For additional information contact your Emerson Process Management sales office. 6

17 HP Valve Product Bulletin Table 2. Trim Material Combinations TRIM USAGE VALVE PLUG CAGE SEAT RING 20A H (5) 203 (NACE )(,2) 204 (NACE) (,2) A 205B 206 (NACE) (,2) 207A 207B H (5) 209 (NACE) (,2) HP ( -6 CL900 & 500 & -2 CL2500) HPA ( -2 CL900,500,2500) HPD & HPS only ( -6 CL900 & 500 & to 2 CL2500) HPAS ( -2 CL900, 500, 2500) HPD 6 CL900 & 500 only HP ( -6 CL900 & 500 & -2 CL2500) HPA ( -2 CL900,500,2500) HPD & HPS only ( -6 CL900 & 500 & to 2 CL2500) HPAS ( -2 CL900, 500, 2500) HP ( -6 CL900 & 500 & -2 CL2500) HPA ( -2 CL900,500,2500) HP ( -6 CL900 & 500 & -2 CL2500) HPA ( -2 CL900,500,2500) HP ( -6 CL900 & 500 & -2 CL2500 S4600 heat-treated for HP, Micro-Form (HPA), and flow down HPAS) S44004 (440C SST) heat-treated for Micro-Flute and Micro-Flat (HPA only) valve plugs S3600 (36 stainless steel) with CoCr-Aseat and guide S3600 (36 stainless steel) with CoCr-Aseat and guide S3600 with CoCr-Aseat and guide S3600 with CoCr-Aseat and guide S3600 with CoCr-Aseat and guide F9withCoCr-A seat and guide S44004 heat-treated/ S2090 stem S44004 heat-treated/ S3600 stem S3600 with CoCr-Aseat and guide S4600 heat-treated S4600 heat-treated HPD & HPS only ( -6 CL900 & 500 & S3600 with CoCr-Aseat to 2 CL2500) HPAS ( and guide -2 CL900, 500, 2500) HPD ( 6 CL900 & 500 only) HP ( -6 CL900 & 500 & -2 CL2500) HPA ( -2 CL900,500,2500) S3600 with CoCr-Aseat and guide S3600 with CoCr-Aseat and guide With Standard Cage S7400 (7-4 SST) H075 heat-treated F22 Cr-Mo alloy steel nitrided F22 Cr-Mo alloy steel nitrided S3600/hard Cr coat S7400 Double H50 heat-treated S4600 heat-treated HPA (S44004 heat-treated seat ring for Micro-Flat S44004 heat-treated seat and liner) S3600/CoCr-A R30006 (Alloy 6) for Micro-Flat valve plugs R30006 seat, liner (6) VALVE BODY MATERIAL () WCC, LCC, WC9 OPERATING TEMPERATURE RANGE _C -29 to 343 ( 3, 4, and 6) -29 to 427 ( and 2) _F -20 to 650 ( 3, 4, and 6) -20 to 800 ( and 2) WCC, LCC, WC9-29 to to 050 S3600/CoCr-A WCC, LCC, WC9-29 to to 050 S3600/CoCr-A R30006 (Alloy 6) for Micro-Flat valve plugs R30006 seat, liner (6) S3600/CoCr-A R30006 (Alloy 6) for Micro-Flat valve plugs R30006 seat, liner (6) CF8M -73 to to 00 WCC, LCC, WC9-46 to to 650 S7400 H075 S3600/CoCr-A WCC, LCC, WC9-29 to to 650 F9ion nitrided F9withCoCr-A C2A -29 to to 00 With Cavitrol III Cage S7400 H075 heat-treated S7400 H075 heat-treated S7400 Double H50 heat-treated With Whisper Trim III Cage S7400 H075 heat-treated S7400 H075 heat-treated F22 steel nitrided F22 steel nitrided S7400 Double H50 heat-treated S44004 WCC, LCC, WC9-29 to 232 (3) -20 to 450 (3) S44004 WCC, LCC, WC9-29 to 232 (3) -20 to 450 (3) S3600/CoCr-A WCC, LCC, WC9-46 to 232 (3) -50 to 450 (3) S4600 heat-treated. If using valve body/trim combinations other than those listed, consult your Emerson Process Management sales office. 2. NACE MR stage and 2 3 stage HPS can be used at temperatures up to 343_C (650_F). 4. and 2 can be used at temperatures up to 427_C (800_F). 5. Trims 202H and 208H have clearances for high-temperature service. 6. For HPA valves. WCC, LCC, WC9-29 to 343 (4) -20 to 650 (4) S3600/CoCr-A WCC, LCC, WC9 343 to to 800 S3600/CoCr-A WCC, LCC, WC9-29 to to 050 S3600/CoCr-A WCC, LCC, WC9-29 to to 050 S3600/CoCr-A WCC, LCC, WC9-46 to to 650 7

18 Product Bulletin HP Valve Table 3. Flowing Pressure Drop Limits for 6 HPD and HPT Valves (Without Cavitrol III or Whisper Trim III Cage) MAXIMUM FLOWING STEM FLOW PRESSURE DROP DIAMETER, MEDIA Bar PSI mm (INCHES) Flow Down Flow Up Flow Down Flow Up (3/4) All except 25.4 () boiler 3.8 (-/4) feedwater 5.8 x 3.8 () (2 x -/4) (-/4) Boiler 5.8 x 3.8 feedwater (2 x -/4). Requires 3.8 mm (-/4 inch) S2090 stem with 52.8 mm (2-inch) plug-to-stem connection. Figure 2. Pressure-Temperature Limits for Trim Material Combinations - 29 FLUID TEMPERATURE, - 29 _C FLUID TEMPERATURE, _C PRESSURE DROP, PSI , FLUID TEMPERATURE, _F PRESSURE DROP, BAR, DIFFERENTIAL PRESSURE DROP, PSI , H, 208H FLUID TEMPERATURE, _F PRESSURE DROP, BAR, DIFFERENTIAL 3-40 FLUID TEMPERATURE, - 40 _C FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C PRESSURE DROP, PSI FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F SOUR SERVICE APPLICATIONS (NACE) 2 NOTES: 2 3 USE TRIM 207B IN 3, 4, AND 6 HP ABOVE 343_C (650_F). NACE MR BEESPECIALLYCAREFULTOSPECIFYSERVICETEMPERATUREIFTRIM202OR208ISSELECTED,ASDIFFERENTTHERMAL EXPANSION RATES REQUIRE SPECIAL PLUG CLEARANCES. 4 THE LIMIT FOR 2-STAGE AND 2 VALVES IS 260 PSIG. FOR 3 TO 6 VALVES THE LIMIT IS 800 PSIG. C , PRESSURE DROP, BAR, DIFFERENTIAL PRESSURE DROP, PSI LIMIT FOR 3-STAGE LIMIT FOR 2-STAGE PRESSURE DROP, BAR, DIFFERENTIAL PRESSURE DROP, PSI FLUID TEMPERATURE, _F PRESSURE DROP, BAR, DIFFERENTIAL 8

19 HP Valve Product Bulletin Table 4. Globe Valve Dimensions with Standard Bonnet A () VALVE ASME EN SIZE, CL900 CL500 RF RTJ BWE SWE RF RTJ PN60 PN250 mm CL CL900 CL500 PN60 PN250 Inches CL RF-raised-face flanges; RTJ-ring-type jointflanges; BWE-buttwelding ends; SWE-socketweld ends. Table 5. Globe Valve Dimensions with Standard Bonnet B () VALVE ASME EN SIZE, CL900 CL500 PN60 PN250 RF RTJ BWE SWE RF RTJ mm (2) (3) CL CL900 CL500 PN60 PN250 Inches (2) (3) CL RF-raised-face flanges; RTJ-ring-type jointflanges; BWE-buttwelding ends; SWE-socketweld ends. 2. Manufactured in U.S.A. 3. Manufactured in Europe and Japan. Table 6. Globe Valve Dimensions with Standard Bonnet STANDARD BONNETS D VALVE Yoke Boss Diameters, mm (Inches) SIZE, G 27 7 (2-3/6) 90 (3-9/6) (5) mm CL900 and Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage () (2) CL Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage Inches CL900 and Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage () (2) CL Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage EXTENSION BONNETS (CL900 AND 500) D VALVE Yoke Boss Diameters, mm (Inches) SIZE, G 27 7 (2-3/6) 90 (3-9/6) (5) mm Std, Whisper III, Cavitrol III 3-Stage Inches Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage , Cavitrol III 2-Stage Manufactured in U.S.A. 2. Manufactured in Europe and Japan.

20 Product Bulletin HP Valve Figure 3. Globe Valve Dimensions with Standard Bonnet (also see tables 4, 5, and 6) MATCH LINE FOR ACTUATOR MATCH LINE FOR ACTUATOR MATCH LINE FOR 585C SERIES ACTUATORS AND TYPE 657, 667 SIZE 00 ACTUATORS MATCH LINE FOR ALL OTHER ACTUATORS 25.4 (.00) mm (INCHES) A5700A-3 FLANGED VALVE WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS BUTTWELDING END VALVE WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS TYPICAL, 2, AND 3 27mm (5-INCH) DIAMETER YOKE BOSS FOR USE WITH ALL VALVES MATCH LINE FOR ACTUATOR MATCH LINE FOR ACTUATOR MATCH LINE FOR 585C SERIES ACTUATORS AND TYPE 657, 667 SIZE 00 ACTUATORS MATCH LINE FOR ALL OTHER ACTUATORS 25.4 (.00) FLANGED VALVE WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS A27A-4 BUTTWELDING END VALVE WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS TYPICAL 3 (EUROPE AND JAPAN MANUFACTURE), 4, AND 6 27mm (5-INCH) DIAMETER YOKE BOSS FOR USE WITH FLANGED OR BUTTWELDING VALVE mm (INCHES) NOTE: FOR DIMENSIONS OF VALVES WITH OTHER END CONNECTIONS, CONSULT YOUR EMERSON PROCESS MANAGEMENT SALES OFFICE. 20

21 HP Valve Product Bulletin Table 7. Dimensions D for Style Extension Bonnet (A, B, and G Dimensions Listed in Figure 3 Do Not Change When Extension Bonnet is Used) D VALVE SIZE, Yoke Boss Diameters, mm (Inches) 7 (2-3/6) 90 (3-9/6) 27 (5) mm (stdtrim) (std, Whisper III, Cavitrol III, 3-stagetrim) (Cavitrol III 2-stage trim) Inches (stdtrim) (std, Whisper III, Cavitrol III 3-stagetrim) (Cavitrol III 2-stage trim) Figure 4. Dimensions D for Style Extension Bonnet (A, B, and G Dimensions Listed in Figure 3 Do Not Change When Extension Bonnet is Used) (also see table 7) MATCH LINE FOR ACTUATOR MATCH LINE FOR 585C SERIES ACTUATORS MATCH LINE FOR ALL OTHER ACTUATORS D 25.4 (.00) 27 mm (5-INCH) DIAMETER YOKE BOSS FOR STYLE EXTENSION BONNET D G B A FLANGED VALVE WITH STYLE EXTENSION BONNET HAVING 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS A570A-2 mm (INCHES) 2

22 Product Bulletin HP Valve Table 8. Angle Valve Dimensions with Standard Bonnet STANDARD BONNETS D VALVE Yoke Boss Diameters, mm (Inches) SIZE, 7 (2-3/6) 90 (3-9/6) 27 (5) CL900 and 500 CL2500 CL900 and 500 CL2500 CL900 and 500 CL2500 mm Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage Inches Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage EXTENSION BONNETS D VALVE Yoke Boss Diameters, mm (Inches) SIZE, 7 (2-3/6) 90 (3-9/6) 27 (5) CL900 and 500 CL2500 CL900 and 500 CL2500 CL900 and 500 CL2500 mm Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage Inches Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage Table. Angle Valve Dimensions with Standard Bonnet G A () VALVE ASME EN SIZE, CL2500 CL900 and 500 PN60 PN250 SWE SWE BWE SWE RF RTJ mm Inches RF raised-face flanges; RTJ ring-type-jointflanges; BWE buttwelding ends; SWE socket-weld ends. 22

23 HP Valve Product Bulletin Figure 5. Angle Valve Dimensions with Standard Bonnet (also see tables 8 and ) MATCH LINE FOR ACTUATOR MATCH LINE FOR ACTUATOR A608A- FLANGED VALVE WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS FLANGED VALVE WITH STYLE EXTENSION BONNET HAVING 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS FOR CL900 AND 500 VALVES, G = A. FOR CL2500 VALVES, SEE TABLE FOR THE G DIMENSION. NOTE: FOR DIMENSIONS OF VALVES WITH OTHER END CONNECTIONS, CONSULT YOUR EMERSON PROCESS MANAGEMENT SALES OFFICE. 23

24 Product Bulletin HP Valve Coefficients Table 20. Fisher HPAT, CL900, 500, and 2500 ( and Equal Percentage Cages Without Liner, Flow Down through the Port) HPAT, CL900 and 500, Flow Down Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T F d HPAT, CL900 and 500, Flow Down HPAT, CL900 and 500, Flow Down HPAT, CL2500, Flow Down HPAT, CL2500, Flow Down HPAT, CL2500, Flow Down At 00% travel. Equal Percentage C v K v X T F d Modified Equal Percentage C v K v X T F d C v K v X T F d Equal Percentage C v K v X T F d Modified Equal Percentage C v K v X T F d

25 HP Valve Product Bulletin Table 2. Fisher HPAT, CL900, 500, and 2500 (Whisper Trim III Cage, Flow Up through the Port) HPAT, CL900 and 500, Whisper Trim, Flow Up Cage Level A (2) P/P±0.6 Valve Size, Port Diameter Maximum Travel mm Inches mm Inches HPAT, CL2500, Whisper Trim, Flow Up A (2) P/P± Flow Coefficient Minimum () C v K v X T C v K v X T Valve should not be required to throttle at less than the minimum coefficient for an extended time, or erosion damage to the valve seat may result. 2. Larger capacities may be available with level A cages depending on service conditions. Table 22. Fisher HPAS, CL900, 500, and 2500 ( and Equal Percentage Cages, Flow Up through the Port) HPAS, CL900 and 500,, Flow Up Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T F d HPAS, CL2500,, Flow Up At 00% travel. C v K v X T F d

26 Product Bulletin HP Valve Table 23. Fisher HPAS, CL900 and 500 (Equal Percentage Cages Without Liner, Flow Down through the Port) HPAS, Equal Percentage, Flow Down Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T HPAS, Modified Equal Percentage (2),FlowDown Modified Equal Percentage C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 2. is equal percentage through 75% of travel. 26

27 HP Valve Product Bulletin Table 24. Fisher HPAS, CL2500 (Equal Percentage Cages Without Liner, Flow Down through the Port) HPAS, Equal Percentage, Flow Down Valve Size, Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches HPAS, Modified Equal Percentage (2),FlowDown Equal Percentage C v K v X T C v K v X T F L () Modified Equal Percentage C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 2. is equal percentage through 75% of travel. 27

28 Product Bulletin HP Valve Table 25. Fisher HPAS, CL900 and 500 (Equal Percentage Cages With Liner, Flow Down through the Port) HPAS, Equal Percentage, Flow Down Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T HPAS, Modified Equal Percentage (2),FlowDown Modified Equal Percentage C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 2. is equal percentage through 75% of travel. 28

29 HP Valve Product Bulletin Table 26. Fisher HPAS, CL2500 (Equal Percentage Cages With Liner, Flow Down through the Port) HPAS, Equal Percentage, Flow Down Valve Size, Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches HPAS, Modified Equal Percentage (2),FlowDown Equal Percentage C v K v X T C v K v X T F L () Modified Equal Percentage C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 2. is equal percentage through 75% of travel. 29

30 Product Bulletin HP Valve Table 27. Fisher HPAS, CL900 and 500 (Micro-Flute Valve Plug) HPAS, CL900 and 500, Micro-Flute, Flow Up Valve Size, HPAS, CL900 and 500, Micro-Flute, Flow Down With or Without Liner and2 6.4Flute 0.25 Flute Flute 0.5Flute 2 Flutes 0.52Flutes. At 00% travel. Equal Percentage C v K v X T C v K v X T C v K v X T Table 28. Fisher HPAS, CL900, 500, and 2500 (Micro-Flat Anti-Cavitation ValvePlug With or WithoutLiner, Flow Down through the Port) HPAS, CL900, 500, and 2500, Micro-Flat Anti-Cavitation, Flow Down With or Without Liner Valve Size, and2 2 Equal Percentage Port Maximum Flow Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T Port Maximum Flow Diameter (2) Travel Coefficient F () L mm Inches mm Inches C v K v Flats 2Flats X T C v K v Flats 2Flats X T C v K v Flats 2Flats X T C v K v Flats 2Flats X T At 00% travel. 2. Micro-Flat Anti-Cavitation trims use a shutoff port diameter which is 0.25 inch larger than the flowing port diameter. Use the shutoff port diameterforactuatorsizing. Note: If np exceeds 000 psig, the life span of the Micro-Flat trim may be shortened. 30

31 HP Valve Product Bulletin Table 29. Fisher HPAS, CL900 and 500 (Micro-Form Valve Plug, Flow Up through the Port) HPAS, Micro-Form, Flow Up Valve Size, 2. At 00% travel Equal Percentage C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T F L () Table 30. Fisher HPAS, CL900 and 500 (Micro-Form Valve Plug, Flow Up through the Port) HPAS, Micro-Form, Flow Up Valve Size, 2. At 00% travel. Modified Equal Percentage Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches 00 Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T F L () 3

32 Product Bulletin HP Valve Table 3. Fisher HPAS, CL2500 (Micro-Form Valve Plug, Flow Up through the Port) HPAS, Micro-Form, Flow Up Table 32. Fisher HPAS, CL2500 (Micro-Form Valve Plug, Flow Up through the Port) HPAS, Micro-Form, Flow Up Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. Modified Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 32

33 HP Valve Product Bulletin Table 33. Fisher HPAS, CL900, 500, and 2500 (Whisper Trim III Cage, Flow Up through the Port) HPAS, CL900 and 500, Whisper Trim III, Flow Up Cage Level A (2) P/P±0.6 Valve Size, Port Diameter Maximum Travel mm Inches mm Inches HPAS, CL2500, Whisper Trim III, Flow Up A (2) P/P± Flow Coefficient Minimum () C v K v X T C v K v X T Valve should not be required to throttle at less than the minimum coefficient for an extended time, or erosion damage to the valve seat may result. 2. Larger capacities may be available with level A cages depending on service conditions. Table 34. Fisher HPAS and HPAT, CL900, 500, and 2500 (Cavitrol III Cages, Flow Down through the Port) HPAS and HPAT, CL900 and 500, Cavitrol III, Flow Down Trim Stage Two Stage Three Stage Valve Port Maximum Flow Minimum Size, Diameter Travel Coefficient Throttling F (3) L mm Inches mm Inches C (2) v () () 38.5 C v K v C v K v () 25.4 () 50 2 C v K v HPAS and HPAT, CL2500, Cavitrol III, Flow Down Two Stage Three Stage () () () 25.4 () 50 2 C v K v C v K v C v K v Cavitrol III trim in the, two stage and the 2, three stage are unbalanced valve plugs. These sizes and constructions are HPS valves; all others in this table are HPT valves. 2. Valves should not be required to throttle at a C v less than the specified minimum C v for an extended period. Erosion damage to the valve seats may result. 3. At 00% travel. 33

34 Product Bulletin HP Valve Table 35. Fisher HPD, CL900 and 500 ( and Equal Percentage Cages, Flow Down through the Port) HPD, CL900 and 500, Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T F d C v K v X T F d C v K v X T F d C v K v X T F d Equal Percentage C v K v X T F d C v K v X T F d C v K v X T F d C v K v X T F d Modified Equal Percentage C v K v X T F d C v K v X T F d C v K v X T F d C v K v X T F d At 00% travel. 2. is equal percentage through 75% of travel. HPD, CL900 and 500, Equal Percentage HPD, CL900 and 500, Modified Equal Percentage (2) 34

35 HP Valve Product Bulletin Table 36. Fisher HPD and HPT, CL2500 ( and Equal Percentage Cages, Flow Down through the Port) HPD, CL2500, Valve Size, Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches HPD, CL2500, Equal Percentage HPD, CL2500, Modified Equal Percentage At 00% travel. C v K v X T F L () Equal Percentage Cv Kv XT Modified Equal Percentage C v K v X T

36 Product Bulletin HP Valve Table 37. Fisher HPD, CL900, 500, and 2500 (Whisper Trim III Cages, Flow Up through the Port) HPD, Whisper Trim III--CL900 and 500, Flow Up Cage Level A (2) P/P±0.6 Valve Size, Port Diameter Maximum Travel mm Inches mm Inches HPD, Whisper Trim III--CL2500, Flow Up A (2) P/P± HPD, Whisper Trim III--CL900 and 500, Flow Up Flow Coefficient Minimum C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T C B v K v P/P±.75 X T C v B3 K v P/P±.75 X T F d C v B3 K v P/P±.75 X T F d C v C K v X T F d C v C K v X T F d C v K v D3 X T C v K v X T Valve should not be required to throttle at less than the minimum coefficient for an extended time, or erosion damage to the valve seat may result. 2. Larger capacities may be available with level A cages depending on service conditions. Notes: The coefficients on this page are also appropriate for the HPT. 36

37 HP Valve Product Bulletin Table 38. Fisher HPS, CL900, 500, and 2500 ( and Equal Percentage Cages, Flow Up through the Port) HPS, CL900 and 500, Flow Up Valve Size, Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches HPS, CL2500, Flow Up HPS, CL900 and 500, Flow Up HPS, CL2500, Flow Up HPS, CL900 and 500, Flow Up HPS, CL2500, Flow Up At 00% travel. C v K v X T F d F L () C v >0.96 K v X T Equal Percentage C v K v X T F d Equal Percentage C v >0.96 K v X T Modified Equal Percentage C v K v X T F d Modified Equal Percentage C v >0.96 K v X T

38 Product Bulletin HP Valve Table 39. Fisher HPS, CL900, 500, and 2500 (Micro-Flute Valve Plug, Flow Up through the Port) HPS, CL900, 500, and 2500, Micro-Flute, Flow Up Table 40. Fisher HPS, CL900 and 500, (Micro-Form Valve Plug, Flow Up through the Port) HPS, CL900 and 500, Micro-Form, Flow Up Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v Flute Flute X T C v K v Flutes 3Flutes X T C v K v X T At 00% travel. Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 38

39 HP Valve Product Bulletin Table 4. Fisher HPS, CL2500, (Micro-Form Valve Plug, Flow Up through the Port) HPS, CL2500, Micro-Form, Flow Up Valve Size, 2. At 00% travel Equal Percentage C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T F L () Table 42. Fisher HPS, CL900 and 500, (Extended Travel Micro-Form Valve Plug, Flow Up through the Port) HPS, CL900 and 500, Extended Travel Micro-Form, Flow Up Modified Equal Percentage Port Maximum Flow Diameter Travel Coefficient mm Inches mm Inches 00 Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T C v K v X T C v K v X T C v K v X T At 00% travel. 39

40 Product Bulletin HP Valve Table 43. Fisher HPS, CL2500, (Extended Travel Micro-Form Valve Plug, Flow Up through the Port) HPS, CL2500, Extended Travel Micro-Form, Flow Up Modified Equal Percentage Valve Port Maximum Flow Size, Diameter Travel Coefficient F () L mm Inches mm Inches C v K v X T C v K v X T C v K v X T C v K v X T C v > K v X T At 00% travel. Table 44. Fisher HPS, CL900, 500, and 2500, (Whisper Trim III Cage, Flow Up through the Port) HPS, Whisper Trim III--CL900 and 500 Cage Level A (2) P/P±0.6 Valve Size, Port Diameter Maximum Travel mm Inches mm Inches HPS, Whisper Trim III--CL2500 Flow Coefficient Minimum C v K v X T C v K v X T A (2) C v K v P/P±0.6 X T HPS, Whisper Trim III--CL900 and 500 C B v K v P/P±.75 X T Valve should not be required to throttle at less than the minimum coefficient for an extended time, or erosion damage to the valve seat may result. 2. Larger capacities may be available with level A cages depending on service conditions. 40

41 HP Valve Product Bulletin Table 45. Fisher HPS and HPT, CL900, 500, and 2500, (Cavitrol III Cages, Standard Seat Design,Flow Down through the Port) HPS and HPT, CL900, 500, and 2500, Cavitrol III, Flow Down Trim Stage Two Stage Three Stage Valve Port Maximum Flow Minimum Size, Diameter Travel Coefficient Throttling F (3) L mm Inches mm Inches C (2) v () () 38.5 C v K v C v K v () 25.4 () 50 2 C v K v C v K v C v K v C v K v C v K v C v K v C v K v HPS and HPT, CL900 and 500, Cavitrol III, Flow Down Two Stage Three Stage. Cavitrol III trim in the, two stage and the 2, three stage are unbalanced valve plugs. These sizes and constructions are HPS valves; all others in this table are HPT valves. 2. Valves should not be required to throttle at a C v less than the specified minimum C v for an extended period. Erosion damage to the valve seats may result. 3. At 00% travel. Table 46. Fisher HPT, CL900, CL500, Cavitrol III, Protected Inside Seat Design, Flow Down HPT, CL900 and 500, Cavitrol III, Protected Inside Seat Design, Flow Down Trim Stage Two Stage Three Stage Valve Size,. Also CL2500 Port Diameter Maximum Travel Flow Coefficient Minimum Throttling C v Valve Opening - Percent of Total Travel mm Inch mm Inch () C v K v C v K v C v K v C v K v C v K v C v K v C v K v

42 Product Bulletin HP Valve Table 47. Fisher HPS, CL900, CL500, CL2500, Cavitrol III 2-Stage Micro-Flat, Flow Down HPS, CL900, CL500, CL2500, Cavitrol III 2-Stage Micro-Flat, Flow Down Valve Shutoff Port Maximum Flow Size, Diameter (2) Travel Coefficient mm Inches mm Inches (6) Min (3) C v K v (3) C v K v (5) C v K v (4) C v K v (3) C v K v (5) C v K v At 00% travel 2. Cavitrol III Micro-Flat trims use a shutoff port diameter which is larger than the flowing port diameter. Use the shutoff port diameter for actuator sizing. 3. Flowing port: mm / 0.5 Inch, Unbalanced Area: cm2 / In2, /2" stem 4. Flowing port: mm / Inch, Unbalanced Area: cm2 / In2, /2" stem 5. Flowing port: mm / Inch, Unbalanced Area: cm2 / In2, 3/4" stem 6. In certain cases, the valve body size, port size, and travel may be the same, but the Cv might be different because of a different assembly part number. Table 48. Fisher HPS, CL900, CL500, CL2500, Cavitrol III 3-Stage Micro-Flat, Flow Down HPS, CL900, CL500, CL2500, Cavitrol III 3-Stage Micro-Flat, Flow Down Valve Shutoff Port Maximum Flow Size, Diameter (2) Travel Coefficient mm Inches mm Inches Min (3) C v K v (4) C v K v (5) C v K v At 00% travel 2. Cavitrol III Micro-Flat trims use a shutoff port diameter which is larger than the flowing port diameter. Use the shutoff port diameter for actuator sizing. 3. Flowing port: 9.5 mm / Inch (Unbalanced Area:.96 cm2 / In2, 3/4" stem 4. Flowing port: mm / 0.5 Inch (Unbalanced Area: cm2 / In2, 3/4" stem 5. Flowing port: mm / Inch (Unbalanced Area: cm2 / In2, 3/4" stem F L () F L ()

43 HP Valve Product Bulletin 43

44 Product Bulletin HP Valve Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Fisher, FIELDVUE, WhisperFlo, Cavitrol, Whisper Trim, and ENVIRO-SEAL are marks owned by one of the companies in the Emerson Process Management business division of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners. The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without notice. Emerson Process Management Marshalltown, Iowa 5058 USA Sorocaba, 8087 Brazil Chatham, Kent ME4 4QZ UK Dubai, United Arab Emirates Singapore 2846 Singapore E449, 20 Fisher Controls International LLC. All rights reserved