SECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.

Size: px
Start display at page:

Download "SECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION."

Transcription

1 SECTION PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting a bid for the work of this SECTION SCOPE OF WORK A. Furnish and install the following, as shown on the Drawings and specified herein: 1. Shelving, fixed and adjustable, with metal standards, brackets, and hardware. 2. Prefinished custom fabricated classroom wall and base cabinets, work room wall and base cabinets, reception and library desks, mailbox units, and work stations, including countertops with side and back splashes, backs, bottoms and drawers, and all necessary hardware. 3. Prefinished veneer faced, veneer core plywood, with solid edge-banding, for all new plywood surfaces and millwork construction noted on the drawings to be "hardwood veneer plywood" or "hardwood plywood" for natural finish. 4. Prefinished solid hardwood for all new millwork, sills, trim and miscellaneous items noted on the drawings as "hardwood". 5. Solid poplar for wood trim designated on the drawings to be painted. 6. Prefinished display cases, including glass doors, tack surfaces, and all necessary hardware. B. Install all new wood doors, metal doors and frames, and finish hardware, as furnished under SECTION HOLLOW METALWORK, SECTION WOOD AND PLASTIC DOORS, and SECTION HARDWARE AND SPECIALTIES, respectively, except as otherwise specified hereunder. C. Install toilet accessories so specified and furnished under SECTION TOILET AND BATH ACCESSORIES. D. Install registers and grilles furnished by SECTION HVAC in cabinetry

2 1.03 RELATED WORK SPECIFIED ELSEWHERE A. The following work is to be performed under the designated SECTIONS: 1.04 SUBMITTALS 1. Rough blocking, furring, nailers, plywood sheathing, and other items of rough carpentry: SECTION ROUGH CARPENTRY. 2. Wood finish flooring: SECTION WOOD AND ATHLETIC FLOORING. 3. Pre-manufactured display cases: SECTION CHALKBOARDS AND TACKBOARDS. 4. Outlets at cabinetry and light fixtures in display cases: SECTION ELECTRICAL. A. Submit complete shop drawings in accordance with the requirements of SECTION SUBMITTALS. B. Include large-scale fabrication details and joinery of finish carpentry items furnished hereunder, and a schedule and cuts of hardware therefore. C. Make actual field measurements of all condition receiving casework and shelving, and include such dimensions on shop drawings. Dimensions indicated on the Contract Drawings, therefore, will be subject to minor corrections. D. Submit the following samples in accordance with the requirements of SECTION SUBMITTALS. 1. Solid wood and plywood - 6 x 6 x 3/4 inch of each species proposed for use, with designation of locations to be used. 2. Plastic laminate - Manufacturer's standard sample chain, in complete range of solid colors and in specified texture, for selection by the Architect. 3. Natural Finish - Samples of colors and finish on each species specified WORKMANSHIP AND QUALITY STANDARDS A. General - Refer to the Drawings for details of new finish, trim, casework and millwork items. 1. Shelving, casework, finish and trim shall conform to design and detail as shown. Where practicable, work shall be finished and assembled at the mill. 2. All millwork and trim shall be furnished smooth and free from all machine and tool marks that will show through the finish. Nails used to fasten finish work will be set to receive putty or wood filler

3 3. All joints will be tight and formed to conceal shrinkage. Miters 4 inches or more from heel to point shall be glued. 4. Finish shall be made in as long lengths as possible and jointed only where solid fastenings can be made. B. Quality Standards - The quality standards of the Architectural Woodwork Institute for PREMIUM GRADE are hereby made a part of this SECTION , except as otherwise noted herein, and all workmanship shall conform to the requirements for premium grade set forth herein. C. Material References - The references to the various wood panel products used herein shall be as classified and characterized by Architectural Woodwork Standards 2009 Panel Products

4 PART 2 PRODUCTS 2.01 FINISH, TRIM AND CASEWORK MATERIALS A. General - Materials required for items of new finish trim, shelving, and casework shall be as follows. (Note: all hardwood to receive natural finish shall be prefinished): 1. Hardwood: Plain sawn select white maple, AWI grade I, for natural finish. 2. Hardwood Veneer Plywood: Select white maple veneer plywood - Plain sliced veneer plywood, slip-matched, AWI grade AA for natural finish. Core shall be medium density particleboard (MDP) or veneer core as specified for the particular application. Plywood shall conform to AWI standards for premium grade. 3. Poplar: Yellow poplar, AWI grade II, to be field painted. B. Panel products for the construction of cabinets, counters, and other finish carpentry items shall be as follows: 1. Cabinet Doors and Drawer fronts: a. For doors and drawer fronts with natural finish: Medium Density Fiberboard (MDF) with hardwood veneer on both sides and solid hardwood edge banding on all exposed edges. b. For doors and drawers with plastic laminate: MDF with the same grade plastic laminate on all (6) surfaces. 2. Base and overhead Cabinet Carcass: a. Natural Finish Cabinets 1. Panels exposed to view on the outside of cabinet: MDF with hardwood veneer on both faces, and solid hardwood edge banding on all exposed edges. 2. Face frames and any exposed door stops or trim: solid hardwood. 3. Panels not exposed to view on the outside of the cabinet and backs or bottoms: particle board with melamine. 3. Plastic laminate finish cabinets. a. All panels except backs and bottoms: Medium Density Fiberboard (MDF) with melamine finish inside cabinet and plastic laminate on all surfaces visible from outside the cabinet. Backs and bottoms MDF or MDP with melamine finish

5 4. Shelving inside enclosed base and overhead cabinets: MDF with melamine finish and performed PVC edgebanding. 5. Shelving for all uses other than inside enclosed cabinets shall be Veneer Core plywood. Shelves for natural finish shall be hardwood veneer with solid edgebanding. Shelving with plastic laminate shall be plastic laminate on all exposed (6) surfaces. 6. Countertops: a. Countertops with sinks: Phenolic resin particleboard. Counters installed over base cabinets shall be one layer of 3/4" material with laminate balancing sheet under counter. b. Counters and work surfaces without sinks: Medium Density Particleboard. Counters over base cabinets shall be one layer of 3/4" material with laminate balancing sheet. c. All countertops not installed over base cabinets shall be two layers of 3/4" material. 7. Plastic Laminate inch thick, high-pressure laminate, meeting or exceeding the performance standards of NEMA, Class I, in a low, nondirective texture, in solid colors and metallic foil finishes as shown on the drawings and as selected by the Architect. Provide balancing sheet of the same thickness of plastic laminate for all plastic laminate surfaces. Interior surfaces so noted shall receive low-pressure (melamine) surfacing material. 8. Cement - For application of laminated plastic - 3M Brand Fastbond 10 or approved equal. 9. Glue - For lamination and fabrication of wood and plywood items - Exterior Grade, phenolic resin glue. 10. Nails - For finish and trim items - 6D or 8D coated or galvanized finish nails. 11. Screws - Flathead galvanized or stainless steel wood screws, of the appropriate size. 12. Panel adhesive as recommended by manufacturer. 13. Tacksurface Linoleum resilient tackable surface material,, Bulletin Board as manufactured by FORBO Linoleum, Inc. Hazeton, PA, or approved equal. Tacksurface material shall be of natural materials consisting of linseed oil, granulated cork, resin binders and dry pigments mixed and calendared onto a natural burlap backing. Color shall extend throughout the 1/4 inch thickness of material

6 2.02 HARDWARE FOR CASEWORK, SHELVING, AND PARTITION WORK A. General - Refer to the Drawings for various new casework, shelving, and partition, and provide all hardware therefore. Unless otherwise noted, finish of all exposed-to-view hardware shall be US26D. All hardware shall be as specified on the Drawings, or approved equal. B. Hardware and Accessories - To establish a level of quality, design and function, Drawings are based on products by manufacturers listed in the schedule shown on the Drawings. Hardware by other manufacturers will be considered for approval as an equal by the Architect upon receipt of adequate supporting data and samples PREFINISH WORK A. Factory finished millwork shall be in accordance with AWI Division 1500-S-4- Finish System Standards for ʻPremium Gradeʼ. Factory finish shall be ultraviolet (UV) cured polyurethance to comply with EPA Title 5 guidelines for Volatile Organic Compound (VOC) emissions limitations. Finish shall meet or exceed performance standards of TR-6 catalyzed polyurethane. Millwork shall be furnished with a clear finish. B. Touch-up all field cuts and imperfections with polyurethane to match pre-finished surfaces GLASS DOORS FOR DISPLAY CASES A. Clear tempered safety glass 1/4 inch, minimum (3/8 inch thick at large lights and doors) heat tempered, annealed, polished clear float glass, PPG Herculite, LOF Tuf-Flex, ASG TRU-TEMP, or approved equal. Edges shall be ground where glass panels and doors are frameless. B. Glass Door Hardware Labora Series sliding glass door fittings as manufactured by Hafele, or approved equal. Furnish and install all glass retainers, track runners and locks required for a complete installation

7 PART 3 EXECUTION 3.01 FABRICATION OF NEW CASEWORK AND SHELVING A. Except as otherwise specified hereunder, fabricate all work in strict accordance with the workmanship standards set forth in the A.W.I. Quality Standards Premium Grade, Section 200, 400, 500, and 600 and the approved shop drawings FABRICATION AND INSTALLATION OF WOOD TRIM A. Fabricate and install all standing and running trim in accordance with the workmanship standards set forth in the A.W.I. Quality Standards Section 300 for Premium Grade, and the approved shop drawings INSTALLATION OF PRESSED STEEL FRAMES A. Erect all pressed steel frames, furnished under SECTION , in accordance with the approved shop drawings and frame schedule. Anchor clips for frames in metal stud partitions will be secured to studs by the drywall construction erector. B. Provide rigid temporary bracing for frames, as required to ensure maintenance of positioning, and remove only after frames have been permanently anchored HANGING AND FITTING OF DOORS AND METAL SIDELIGHT PANELS A. Receive, store and be responsible for hardware as furnished under SECTION HARDWARE AND SPECIALTIES. B. Fit all hinged doors to their respective openings. Install metal sidelight panels as indicated on the Drawings. C. Install fire rated and non-rated doors in accordance with NFPA 80, manufacturer's instructions, and UL and Massachusetts Building Code requirements. Warp, bow and cup in wood doors shall not exceed 1/4 inch over a 36 x 84 inch surface. D. Fit all hardware accurately, from templates supplied with hardware apply securely, and adjust carefully. E. Should pre-finished wood doors require cutting or remachining, seal exposed surfaces with two brush coats of oil base polyurethane or varnish before hanging. F. Prior to Substantial Completion of the Contract, and before building is occupied, inspect entire building with Architect, to ensure that each piece of finish hardware is undamaged and in perfect order and that the proper key for each lock is identified

8 3.05 INSTALLATION OF TOILET ACCESSORIES A. Perform installation of accessories furnished under SECTION TOILET AND BATH ACCESSORIES, in accordance with the templates and instructions furnished by the accessory manufacturer. Refer to the Drawings for various locations REHABILITATIONS AND REPAIRS TO EXISTING LOBBY WOOD DOORS, TRIM, AND A. Perform all required carpentry modifications to these items, including cutting as required to ensure proper fitting of new patching woodwork. Make joints between new work and existing as tight as possible to minimize the transition of materials FINAL INSPECTION A. Just prior to completion of all work under this SECTION , the General Contractor, with the Architect, shall inspect all portions of the work and shall make any required adjustments or corrections to the work. END OF SECTION

Architectural Casework 06400-01. 1.01 Description of Work

Architectural Casework 06400-01. 1.01 Description of Work 06400-01 1.01 Description of Work A. Extent of each type of architectural millwork and casework as indicated on drawings. Types of architectural casework shall include both stained and plastic laminated

More information

INSTRUCTIONS FOR COORDINATION SECTION 06651 SOLID SURFACE FABRICATIONS

INSTRUCTIONS FOR COORDINATION SECTION 06651 SOLID SURFACE FABRICATIONS INSTRUCTIONS FOR COORDINATION SECTION 06651 SOLID SURFACE FABRICATIONS 1. Paragraph 1.02 Provide solid surface countertops at sinks locations. Provide solid surface window sills at drywall framing walls.

More information

DIY CABINET REFACING INSTALLATION GUIDE

DIY CABINET REFACING INSTALLATION GUIDE DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products

More information

SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront

SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront PART 1 GENERAL 1.01 Work Included SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS System 402 Flush-Glazed Screw Spline Storefront A. Furnish and install aluminum architectural storefront system

More information

MIDMARK DENTAL CABINETRY vs LOCAL CABINET MAKERS

MIDMARK DENTAL CABINETRY vs LOCAL CABINET MAKERS MIDMARK DENTAL CABINETRY vs LOCAL CABINET MAKERS Because dental practices are specialized treatment facilities, they have needs that are profession and practice specific. Integra Dental Casework and Artizan

More information

FF+E Package 1: Casegoods Specifications UCSD NORTH CAMPUS HOUSING, PHASE 1

FF+E Package 1: Casegoods Specifications UCSD NORTH CAMPUS HOUSING, PHASE 1 FF+E Package 1: Casegoods Specifications UCSD NORTH CAMPUS HOUSING, PHASE 1 Issue Date: 3/3/2009 Each furniture item scheduled in this specification manual is assigned a "key" code; each key code is crossreferenced

More information

Delivery Split delivery Off Hr delivery Store off site To tailgate To floor Accepted by

Delivery Split delivery Off Hr delivery Store off site To tailgate To floor Accepted by ARCHITECTURAL WOODWORK QUALITY STANDARDS SPECCHEK INSERT MODULAR CABINETS AWI Grades Transparent Fin. Opaque Fin. Laminate clad By room By floor By item Size Width Height Thickness Construction Flush overlay

More information

SECTION 062043 FIRE-RATED WOOD JAMBS

SECTION 062043 FIRE-RATED WOOD JAMBS SECTION 062043 FIRE-RATED WOOD JAMBS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. [Solid wood] [Particle board] fire-rated interior door[ and sidelight] frames. 2. Intumescent/wood fire-rated interior

More information

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2

More information

Eggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art

Eggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art D O O R F R A M E S Eggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art D O O R F R A M E S Eggers Industries

More information

B. Related categories: The following categories contain requirements that relate to this section:

B. Related categories: The following categories contain requirements that relate to this section: ORIENTED STRAND BOARD PART I. - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply

More information

A. Product data. Unless otherwise indicated, submit the following for each type of product provided under work of this Section: SPECIFIER NOTE:

A. Product data. Unless otherwise indicated, submit the following for each type of product provided under work of this Section: SPECIFIER NOTE: This is a guidance document with sample specification language intended to be inserted into project specifications on this subject as appropriate to the agency's environmental goals. Certain provisions,

More information

SECTION 098400 ACOUSTICAL WALL TREATMENT. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.

SECTION 098400 ACOUSTICAL WALL TREATMENT. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. SECTION 098400 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

CHALKBOARDS, MARKERBOARDS, TACKBOARDS, DISPLAY CASES, AND BULLETIN BOARD CABINETS

CHALKBOARDS, MARKERBOARDS, TACKBOARDS, DISPLAY CASES, AND BULLETIN BOARD CABINETS SECTION 10100 CHALKBOARDS, MARKERBOARDS, TACKBOARDS, DISPLAY CASES, AND BULLETIN BOARD CABINETS PART 1 GENERAL 1.01 SUBMITTALS A. Product Data: Submit copies of manufacturer's technical data and installation

More information

All work must conform to the National Electric Code, latest edition, and all other applicable codes and regulations.

All work must conform to the National Electric Code, latest edition, and all other applicable codes and regulations. DIVISION 16 ELECTRICAL SECTION 16100 - ELECTRICAL PART 1 - GENERAL SCOPE All electrical work as shown on the drawings and as necessary to provide a complete electrical system. Include primary service,

More information

PART 1 GENERAL 1.1 SECTION INCLUDES

PART 1 GENERAL 1.1 SECTION INCLUDES J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including

More information

SECTION 07 61 13 STANDING SEAM METAL ROOFING

SECTION 07 61 13 STANDING SEAM METAL ROOFING SECTION 07 61 13 STANDING SEAM METAL ROOFING PART 1 GENERAL 1.01 SCOPE OF WORK A. The Work shall include all labor, materials, equipment and supervision required to complete the work of the above referenced

More information

DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS

DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS NOTICE TO BIDDERS BID FORM INSTRUCTIONS TO BIDDERS CONTRACTOR S BID FOR PUBLIC WORK - FORM 96 MINORITY AND WOMEN S BUSINESS ENTERPRISE PARTICIPATION

More information

Whitley Manufacturing Co., Inc. 201 W. First Street S. Whitley, IN 46787 Phone (260) 723-5131 Sales Fax (260) 723-6396 whitley@whitleyman.

Whitley Manufacturing Co., Inc. 201 W. First Street S. Whitley, IN 46787 Phone (260) 723-5131 Sales Fax (260) 723-6396 whitley@whitleyman. Building Type Building Code Whitley Classroom Buildings BOCA, UBC, SBCCI, NEC, ADA Structural Support Outrigger construction standard, Whitley model classrooms. Main support beams to be 12 11.8# per lineal

More information

City of San Diego, CWP Guidelines

City of San Diego, CWP Guidelines PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,

More information

VA25014B0516 VA CINCINNATI PROJECT NO. 539-328 INPATIENT BED TOWER ADDITION (4 TH AND 5 TH FLOORS) SECTION 09 29 00 GYPSUM BOARD

VA25014B0516 VA CINCINNATI PROJECT NO. 539-328 INPATIENT BED TOWER ADDITION (4 TH AND 5 TH FLOORS) SECTION 09 29 00 GYPSUM BOARD SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board, vapor retarder and air and moisture barrrier. 1.2 RELATED WORK A. Installation

More information

Scotch-Weld Polyurethane Reactive (PUR) Easy Adhesive Systems

Scotch-Weld Polyurethane Reactive (PUR) Easy Adhesive Systems 3 Scotch-Weld Polyurethane Reactive (PUR) Easy Adhesive Systems Structural adhesive benefits with hot melt adhesive speed for wood, plastic and more. 3M Scotch-Weld Polyurethane Reactive (PUR) Easy (170

More information

SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING

SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING PART ONE GENERAL DESCRIPTION This section includes pre-formed standing seam metal roofing and related flashings, closures, trim and accessories including,

More information

ATTACHMENT A STRUCTURAL INTERIOR DESIGN (SID) REQUIREMENTS

ATTACHMENT A STRUCTURAL INTERIOR DESIGN (SID) REQUIREMENTS ATTACHMENT A STRUCTURAL INTERIOR DESIGN (SID) REQUIREMENTS 1.0 GENERAL INFORMATION Structural Interior Design includes all building related elements and components generally part of the building itself,

More information

HOW TO INSTALL A BEAUTIFUL NEW KITCHEN

HOW TO INSTALL A BEAUTIFUL NEW KITCHEN HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge

More information

CLEAR-DIVISIONS CENTERFOLD

CLEAR-DIVISIONS CENTERFOLD CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in

More information

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word

More information

Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved

Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing

More information

RACQUETBALL, HANDBALL OR SQUASH COURTS AND GYMNASIUM WALL SURFACES

RACQUETBALL, HANDBALL OR SQUASH COURTS AND GYMNASIUM WALL SURFACES 1807 Elmwood Avenue, Suite 275 Buffalo, New York 14207 (800) 543-5155 RACQUETBALL, HANDBALL OR SQUASH COURTS AND GYMNASIUM WALL SURFACES Fiberesin Wall System Provide materials and labor to complete courts

More information

Irvinton Village Apartments 2901 Fulton Houston, Texas 77009 Houston Housing Authority J. Allen Management Managing Agent

Irvinton Village Apartments 2901 Fulton Houston, Texas 77009 Houston Housing Authority J. Allen Management Managing Agent Irvinton Village Apartments 2901 Fulton Houston, Texas 77009 Houston Housing Authority J. Allen Management Managing Agent Scope for Irvinton Village Unit #512 Overall Scope: Demolition, Renovation, and

More information

LEGACY REPORT. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council RETAINED ON U.S.

LEGACY REPORT. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council RETAINED ON U.S. ICC-ES Legacy Report ER-5043* Reissued March 2004 www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council Legacy report on the 1997 Uniform Building Code DIVISION: 09

More information

DESK CABINETS & BOOKSHELVES

DESK CABINETS & BOOKSHELVES 142 : Desk Base Desk Base Cabinets File Drawer Base Cabinet Desk Base Cabinet 1 Factory Installed Wastebasket FDB1821 DWBT1821 Desk Base cabinets are 12 to 24 wide, 28 1 2 high and 20 3 4 or 24 deep. Cathedral

More information

VOLUME V GUIDELINES FOR DESIGN CONSULTANT TABLE OF CONTENTS APPENDIX B: MASTER CONSTRUCTION SPECIFICATIONS AND PREPARATION GUIDE, DIVISIONS 0-10

VOLUME V GUIDELINES FOR DESIGN CONSULTANT TABLE OF CONTENTS APPENDIX B: MASTER CONSTRUCTION SPECIFICATIONS AND PREPARATION GUIDE, DIVISIONS 0-10 VOLUME V GUIDELINES FOR DESIGN CONSULTANT TABLE OF CONTENTS APPENDIX B: MASTER CONSTRUCTION SPECIFICATIONS AND PREPARATION GUIDE, DIVISIONS 0-10 SECTION B1: PREPARATION GUIDE B1.1 INTRODUCTION... B1-1

More information

QUOTATION FOR EXAMPLE BATHROOM RENOVATION

QUOTATION FOR EXAMPLE BATHROOM RENOVATION QUOTATION FOR EXAMPLE BATHROOM RENOVATION Prepared For: PEGASUS Client 99 Washington St Melrose, MA 02176 Quotation valid for 90 from: 12/21/10 PEGASUS Design-To-Build is pleased to have the opportunity

More information

We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.

We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit. Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden

More information

SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK

SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. This section covers the pre-finished, pre-fabricated Architectural standing seam roof system. All metal trim,

More information

CLEAR-DIVISIONS APERTO

CLEAR-DIVISIONS APERTO CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the

More information

Schlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing

Schlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing Substrate, structural panel, bonded waterproofing The universal substrate for tiles Perfect covering No matter whether you work with mosaics or large format tiles, an absolutely level substrate with straight

More information

We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.

We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit. Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden

More information

CONTEMPORARY - TRANSITIONAL RECEPTION STATIONS

CONTEMPORARY - TRANSITIONAL RECEPTION STATIONS Reception stations, the first impression expressed to visitors in your office. Transitional styling to coordinate with your other office settings, available in a selection of 16 walnut, cherry, oak, maple

More information

Alpha System ADAPTABLE KEWAUNEE LABORATORY FURNITURE. encouraging new discovery

Alpha System ADAPTABLE KEWAUNEE LABORATORY FURNITURE. encouraging new discovery Alpha System ADAPTABLE LABORATORY FURNITURE KEWAUNEE encouraging new discovery Alpha 6 partition modules with Kemresin worktops. Minneapolis, Minnesota Alpha 6 partition modules with Alpha overhead service

More information

Cascade Remodeling Inc. PO Box 25687 Portland, OR 97298 Catalyzing Euphoria Phone (503) 297-2055, FAX (503) 297-0579 CCB # 67007

Cascade Remodeling Inc. PO Box 25687 Portland, OR 97298 Catalyzing Euphoria Phone (503) 297-2055, FAX (503) 297-0579 CCB # 67007 SPECIFICATIONS For Sample Customer SCOPE OF WORK: The contractor will provide labor and/or materials for the work as outlined in the estimate and the following specification. The contractor s estimate

More information

AMERICAN GOTHIC PLAYHOUSE

AMERICAN GOTHIC PLAYHOUSE AMERICAN GOTHIC PLAYHOUSE Project Plan #856 Sheet 1 of 5 Pick a spot and get started with the beautiful that your kids will love. The design of the playhouse includes 35 square feet of interior space plus

More information

How to secure your property after a disaster

How to secure your property after a disaster How to secure your property after a disaster The Red Guide to Recovery HOuse secured properly Board-Up of Windows, Doors and Roof Hole. Lot secured with Perimeter Fencing. Fires, floods, tornadoes, hurricanes,

More information

A D D E N D U M # 3 QUESTIONS FROM BIDDERS: DATE: November 5, 2012. All Bidders. Jenne dos Santos, CBI Consulting Inc. City of Chelsea, MA

A D D E N D U M # 3 QUESTIONS FROM BIDDERS: DATE: November 5, 2012. All Bidders. Jenne dos Santos, CBI Consulting Inc. City of Chelsea, MA Page 1 of 10, Addendum No. 3 Temporary Garage Structure City of Chelsea, MA November 5, 2012 CBI Job No.: 12055-A A D D E N D U M # 3 DATE: November 5, 2012 TO: FROM: PROJECT: All Bidders Jenne dos Santos,

More information

SECTION 00 0110 TABLE OF CONTENTS. H. 00 2115.01 - Proposed Material, Product or Equipment Substitution Request

SECTION 00 0110 TABLE OF CONTENTS. H. 00 2115.01 - Proposed Material, Product or Equipment Substitution Request SECTION 00 0110 PROCUREMENT AND CONTRACTING REQUIREMENTS 1.1 DIVISION 00 -- PROCUREMENT AND CONTRACTING REQUIREMENTS A. 00 0101 - Project Title Page B. 00 0105 - Certifications Page C. 00 0110 - Table

More information

WASHROOM UPGRADE SIR CHARLES TUPPER BUILDING 2250 RIVERSIDE DRIVE, OTTAWA, ON SIR CHARLES TUPPER BUILDING A0.0 COVER SHEET / DRAWING LIST

WASHROOM UPGRADE SIR CHARLES TUPPER BUILDING 2250 RIVERSIDE DRIVE, OTTAWA, ON SIR CHARLES TUPPER BUILDING A0.0 COVER SHEET / DRAWING LIST 0 RIVERSIDE DRIVE, OTTAWA, ON A0.0 COVER SHEET / DRAWING LIST A0. LEGEND AND GENERAL NOTES A0. GENERAL NOTES A0. GENERAL NOTES A0. TYPICAL WASHROOM WALL/SINK SECTION A0. DETAIL - CONTROL JOINT A0. DETAIL

More information

SECTION 14 20 10 - FREIGHT & PARKING GARAGE ELEVATORS PART I - GENERAL

SECTION 14 20 10 - FREIGHT & PARKING GARAGE ELEVATORS PART I - GENERAL SECTION 14 20 10 - FREIGHT & PARKING GARAGE PART I - GENERAL 1.1 SECTION INCLUDES [NOTE to AE: The following lists requirements that are specific to freight elevators. These requirements are in addition

More information

CLEAR-DIVISIONS VARIOFOLD

CLEAR-DIVISIONS VARIOFOLD CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the

More information

LABORATORY CASEWORK. Table of Contents. Laboratory Cabinetry and Specialties. ADVANTAGE laboratory. Series/Model Number Specification...

LABORATORY CASEWORK. Table of Contents. Laboratory Cabinetry and Specialties. ADVANTAGE laboratory. Series/Model Number Specification... PREVIOUS VIEW LABORATORY CASEWORK Laboratory Cabinetry and Specialties Table of Contents Series/Model Number Specification... 3 Perimeter Tables... 5 s... 6-9 Steel Legs... 6-7 Wood Legs... 8-9 Student

More information

Guide Specifications for Maple Flooring Systems

Guide Specifications for Maple Flooring Systems Guide Specifications for Maple Flooring Systems MFMA Guide Specification for Resilient Pre-Engineered Fixed Panel System Purpose This Guide Specification is designed to assist in the production of actual

More information

Schluter -KERDI-BOARD Substrate, building panel, bonded waterproofing

Schluter -KERDI-BOARD Substrate, building panel, bonded waterproofing Schluter -KERDI-BOARD Substrate, building panel, bonded waterproofing Schluter -KERDI-BOARD The universal substrate for tiles Flat. Level. Plumb. Square. No matter the quality, cost, or extravagance of

More information

Build Your Own Kitchen Cabinets

Build Your Own Kitchen Cabinets HOME IMPROVEMENT Build Your Own Kitchen Cabinets RAISED PANELS BEVELED GLASS LIGHTED VALANCE / 8 " INSET DRAWERS 40 If you ve dreamed of building a kitchen full of cabinets, stop dreaming and start building.

More information

BASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401

BASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401 BASIC FIRE DOOR REQUIREMENTS SHEET NO. 401 Fire door openings are classified by their locations in the building. The location determines the length of exposure protection required, based on the potential

More information

Pre-Cut Sauna Specifications

Pre-Cut Sauna Specifications Pre-Cut Sauna Specifications When to specify a Pre-Cut Liner Sauna: Please review diagrams at the beginning of these specs. Pre-Cut saunas are best suited for projects that require the four walls and ceiling

More information

Sub-Bid Contractor Update Statement. Tab A - Invitation for Bids. Tab B - Instructions to Bidders

Sub-Bid Contractor Update Statement. Tab A - Invitation for Bids. Tab B - Instructions to Bidders INTRODUCTORY INFORMATION TABLE OF CONTENTS 00 0101 PROJECT TITLE PAGE PROCUREMENT REQUIREMENTS (PROJECT MANUAL) Tab A - Invitation for Bids Tab B - Instructions to Bidders Tab C Bid Form for General Bids

More information

3M Industrial Adhesives and Tapes Division Industrial Bonding Solutions for Woodworking

3M Industrial Adhesives and Tapes Division Industrial Bonding Solutions for Woodworking 3M Industrial Adhesives and Tapes Division Industrial Bonding Solutions for Woodworking Over the years 3M adhesive engineers have developed some of the most innovative bonding solutions in the world. 3M

More information

DE Frame with C Series Sidelight

DE Frame with C Series Sidelight TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder

More information

March 14, 2007. Installation of Bay, Bow and Garden Windows

March 14, 2007. Installation of Bay, Bow and Garden Windows March 14, 2007 Re: Installation of Bay, Bow and Garden Windows Attached are the Atrium Companies, Inc recommendation for the installation of bay, bow and garden windows. These instructions were developed

More information

WHI 90-Minute Rated Veneered Door Frame Installation Instructions

WHI 90-Minute Rated Veneered Door Frame Installation Instructions No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,

More information

Open Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows

Open Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows Open Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows Series 2050 Garden Window The Series 2050 standard garden window has an outstanding reputation for its distinctive design and excellent

More information

kirei KIREI BOARD natural design innovation organic contemporary www.ecodepotinc.com Dimensions: Beautiful Natural Materials

kirei KIREI BOARD natural design innovation organic contemporary www.ecodepotinc.com Dimensions: Beautiful Natural Materials KIREI BOARD Beautiful Natural Materials A beautiful natural Interior millwork material made with renewable, non-toxic components. Strong, lightweight and environmentally friendly, Kirei Board is an easily

More information

C. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.

C. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction. SECTION 081216 - INTERIOR ALUMINUM DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

BOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping.

BOQ SPECIFICATIONS. The Blind system consist of a coated aluminium tube of 38 mm diameter with provision of fabric clamping. BOQ SPECIFICATIONS VERTICAL BLINDS Vertical Blinds made of glass fibre fabrics in width 5 (or 4 ). Minimum overlapping of ¾ in fabric. Top aluminium anodized rail of 1.4 mm thickness. 2 inch wide channel

More information

DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS

DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the contract, including general and supplementary conditions and other Division 1

More information

REFRIGERATION. Standard Features & Accessories. Model Options. Built-In 30 W. Full-Height Wine Cellar. All models include. VCWB300 Professional

REFRIGERATION. Standard Features & Accessories. Model Options. Built-In 30 W. Full-Height Wine Cellar. All models include. VCWB300 Professional Standard Features & Accessories All models include Capacity accommodates up to 150 full-size bottles o 84 H./24 D. Exclusive TriTemp storage system o Three independent temperature zones o Settings are

More information

FORm_office UPPER STORAGE OPTIONS

FORm_office UPPER STORAGE OPTIONS FORm_office UPPER STORAGE OPTIONS UPPER STORAGE OPTIONS In today s condensed, open plan office environments, storage volume has been significantly reduced. Overheads have been eliminated, and desktop space

More information

SECTION 07 42 13 METAL WALL PANELS

SECTION 07 42 13 METAL WALL PANELS Mitsubishi Plastics Composites America, Inc. 401 Volvo Parkway Chesapeake, VA 23320 Phone: (800) 422-7270 Fax: (757) 436-1896 E-mail: info@alpolic.com www.alpolic-northamerica.com This MANU-SPEC utilizes

More information

CHAPTER 7: Building Systems ROOFING SYSTEMS

CHAPTER 7: Building Systems ROOFING SYSTEMS ROOFING SYSTEMS Purpose Examples 1. Shingle roof system 2. Metal roof with blanket insulation 3. Metal roof with rigid insulation 4. Built-up asphalt roof system 5. Single-ply roof system 6. Modified Bitumen

More information

TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II 2009145.00

TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II 2009145.00 SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

Roped Hydraulic Residential Elevator Specifications

Roped Hydraulic Residential Elevator Specifications January 1, 2004 Roped Hydraulic Residential Elevator Specifications P.O. Box 749, 5191 Stump Rd., Plumsteadville, PA 18949 Toll Free: 888-443-2800, Phone: 215-766-3380, Fax: 215-766-3385 CONTENTS Part

More information

IMPROVEMENT COST ESTIMATE powered by HomeFixers

IMPROVEMENT COST ESTIMATE powered by HomeFixers IMPROVEMENT COST ESTIMATE powered by HomeFixers 123 Main St, Anytown, USA 12345 2000 SF $ 45,041.06 100.0% $22.52 per sq. ft. Stage 1: Pre-Construction $ 1,461.00 3.2% 1 House Secured $ 106.00 0.2% Lockbox

More information

Andersen Electric Window Opener for Andersen Awning and Roof Windows

Andersen Electric Window Opener for Andersen Awning and Roof Windows W A Electric Window Opener Electric Window Opener for Awning and Roof Windows Congratulations! You have just purchased one of the many fine products. For ease of installation and continued enjoyment of

More information

The tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results

The tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results Foolproof Crosscut Sleds Innovative approach guarantees perfect results B Y A L A N T U R N E R The tablesaw may be your shop s most valuable cutting tool, but for precise, repeatable crosscuts it needs

More information

Mark Cramer Inspection Services, Inc.

Mark Cramer Inspection Services, Inc. Mark Cramer Inspection Services, Inc. 492 Twentieth Avenue, Indian Rocks Beach, FL 34635-2970 (727) 595-4211 Fax (727) 596-7583 Certified Member #12085 American Society of Home Inspectors Construction

More information

Core and Frame Details

Core and Frame Details and Frame Details February, 2014 Contents Architectural Flush Wood Door Codes 1-2 Performance Standards 3 GRAHAM SUPREME DOOR GSD SR 35-40 4 GSD SR 41-45 5 GSD SR 31, 33, 39, and 44 6 GSD SR 46-47 7 GRAHAM

More information

Specifications. Preformed Metal Wall and Roof Panels. Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023

Specifications. Preformed Metal Wall and Roof Panels. Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023 Specifications Preformed Metal Wall and Roof Panels Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023 Section 07410 Preformed Metal Wall and Roof Panels Structural

More information

Facility Summary. Facility Condition Summary. Seattle School District David T. Denny International Infrastructure. Facility Components

Facility Summary. Facility Condition Summary. Seattle School District David T. Denny International Infrastructure. Facility Components Infrastructure Facility Condition Summary Weighted Avg Condition Score Facility Components Systems Surveyor/ Date Done Comments G Sitework.9 Site Improvements Parking Pedestrian Paving Site Development

More information

Composite Stone Veneer

Composite Stone Veneer Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:

More information

SECTION 07400 STANDING SEAM METAL ROOF

SECTION 07400 STANDING SEAM METAL ROOF SECTION 07400 STANDING SEAM METAL ROOF PART 1 - GENERAL 1.01 SECTION INCLUDES A. Work described in this section includes pre-formed standing seam metal roofing system complete with clips, perimeter and

More information

STAIR TREAD & RISER INSTALLATION GUIDELINES

STAIR TREAD & RISER INSTALLATION GUIDELINES STAIR TREAD & RISER INSTALLATION GUIDELINES ARTISTIC FINISHES DOES NOT WARRANTY THE COMPLETENESS OR ACCURACY OF ANY INSTALLATION. THE INSTALLATION CONTRACTER MUST HAVE THE EXPERIENCE AND KNOWLEDGE TO COMPLETE

More information

Quality alu LED profiles

Quality alu LED profiles Quality alu LED LED PROFILES - PRODCUT CATALOGUE 2010 Quality Aluminum LED Manufacturer & Designer NEW RECESSED SLIM LINE 15mm Introduction: It is recessed type of the aluminum LED profile to build into

More information

Total Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).

Total Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017). # Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL

More information

PROJECT TITLE : 2-STOREY RESIDENCE LOCATION : ALONG DAANG HARI,MOLINO.BACOOR,CAVITE OWNER : CUEVASVILLE REALTY

PROJECT TITLE : 2-STOREY RESIDENCE LOCATION : ALONG DAANG HARI,MOLINO.BACOOR,CAVITE OWNER : CUEVASVILLE REALTY PROJECT TITLE : 2-STOREY RESIDENCE LOCATION : ALONG DAANG HARI,MOLINO.BACOOR,CAVITE OWNER : CUEVASVILLE REALTY GENERAL SPECIFICATIONS These specifications are intended to cover the construction of the

More information

Kuebler JASPER DESK. Ordering Options Doors Locking per set of doors (LK) - Add $55 List

Kuebler JASPER DESK. Ordering Options Doors Locking per set of doors (LK) - Add $55 List Desk Tops and Veneer - Standard High Pressure Laminate - No Upcharge Grommets (GR2) - Two grommets - Add $121 List Pedestal Drawers File/File Pedestal (FF) Change Box/Box/File to File/File Add FF after

More information

MRI RF SHIELDING DESIGN

MRI RF SHIELDING DESIGN MRI RF SHIELDING DESIGN Nelco s MRI RF Shielding is specifically designed for the MRI industry. Our engineers have developed a shielded enclosure made entirely of nonmagnetic materials that is unsurpassed

More information

GYPSUM BOARD, GYPSUM PANEL PRODUCTS AND PLASTER

GYPSUM BOARD, GYPSUM PANEL PRODUCTS AND PLASTER CHAPTER 25 GYPSUM BOARD, GYPSUM PANEL PRODUCTS AND PLASTER User note: Code change proposals to this chapter will be considered by the IBC Structural Code Development Committee during the 2016 (Group B)

More information

COST OF WORK FORM. Abbreviations: ea = each, LF = linear feet, SF = square feet, HSF = square feet of living area (including garage conversion space)

COST OF WORK FORM. Abbreviations: ea = each, LF = linear feet, SF = square feet, HSF = square feet of living area (including garage conversion space) COST OF WORK FORM All costs shown are estimates using base grade materials, taxes, and labor. For houses where a higher quality is indicated, the costs should be increased for work requiring upgraded materials.

More information

Division 9. SignaFlor Pad and Pour Flooring System

Division 9. SignaFlor Pad and Pour Flooring System Division 9 SignaFlor Pad and Pour Flooring System SPECIFICATIONS Page 1. General... 2 1.1 Description 2 1.2 Quality Assurance 2 1.3 Submittals 2 1.4 Delivery and Storage 3 1.5 Warranty 3 1.6 Working Conditions

More information

PUBLIC RESTROOMS, DESIGN INTENT

PUBLIC RESTROOMS, DESIGN INTENT PUBLIC RESTROOMS, DESIGN INTENT 1.01 STRUCTURAL A. Where feasible, metal stud partitions will be constructed on a 6 high concrete curb. 1.02 MECHANICAL A. Restrooms will have a minimum of 15 air changes

More information

SECTION 10670 STORAGE SHELVING. Copyright 2007-2011 ARCAT, Inc. - All rights reserved

SECTION 10670 STORAGE SHELVING. Copyright 2007-2011 ARCAT, Inc. - All rights reserved 1 SECTION 10670 STORAGE SHELVING Copyright 2007-2011 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Vinyl-coated ventilated shelving. B. Laminated closet systems. C. Specialty

More information

STANDARD MATERIAL SPECIFICATIONS FOR OUR PREFAB BALI HOUSES

STANDARD MATERIAL SPECIFICATIONS FOR OUR PREFAB BALI HOUSES STANDARD MATERIAL SPECIFICATIONS FOR OUR PREFAB BALI HOUSES We offer four main prefab building material options, viz. a Basic, a Standard, a DeLuxe and a, each of them fitted to your budget or requirements.

More information

ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES

ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES PART 1 - GENERAL 1.1 SCOPE OF WORK SECTION 06610 FIBERGLASS REINFORCED PLASTICS (FRP) FABRICATIONS PULTRUDED SQUARE TUBE LADDER

More information

TRADITIONAL RECEPTION STATIONS

TRADITIONAL RECEPTION STATIONS TRADITIONAL Reception stations, the first impression expressed to visitors in your office. Traditional styling to coordinate with your other office settings, available in a selection of 15 walnut, cherry,

More information

INSTALLATION OF A BAY WINDOW

INSTALLATION OF A BAY WINDOW INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening

More information

Important Information for Installer & Homeowner

Important Information for Installer & Homeowner Important Information for Installer & Homeowner Homeowner: Please keep this information for your records, do not discard! Installation Instructions for Wood Frame Construction Replacement (See other side

More information

RESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000

RESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000 RESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000 SECTION R905 REQUIREMENTS FOR ROOF COVERINGS R905.1 Roof covering application. Roof coverings

More information

09/07/07 GLASSFIBER REINFORCED CEMENT (GRC) C. S. I. Spec 03500 Master Spec. 03 49 00 Page 1

09/07/07 GLASSFIBER REINFORCED CEMENT (GRC) C. S. I. Spec 03500 Master Spec. 03 49 00 Page 1 C. S. I. Spec 03500 Page 1 PART 1 - GENERAL 1.01 SUMMARY:.01 Provide special glassfiber reinforced cement (GRC) shapes in accordance with the requirements of the contract documents..02 The installing contractor

More information

Air-Conditioning, Heating, and Refrigeration Institute. Sheet Metal and Air-Conditioning Contractors National Association

Air-Conditioning, Heating, and Refrigeration Institute. Sheet Metal and Air-Conditioning Contractors National Association Air-Conditioning, Heating, and Refrigeration Institute Sheet Metal and Air-Conditioning Contractors National Association GUIDELINE B-1997 ACKNOWLEDGEMENT These guidelines for Roof Mounted Outdoor Air-

More information