CAUTION - FOR YOUR SAFETY

Transcription

1 TM 16 in. REEL MOWER ITEM / ARTICULO # MODEL / MODELO #26133 CAUTION - FOR YOUR SAFETY READ YOUR OPERATOR S MANUAL COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP OR OPERATE YOUR NEW REEL MOWER. ALL OPERATORS OF THIS EQUIPMENT SHOULD READ AND UNDERSTAND ALL SAFETY RULES PRINTED ON THE MACHINE AND IN THIS OPERATOR S MANUAL BEFORE USE. NOTICE: On the nameplate of your machine you will find the serial number and MFG date code of your unit. Please record these numbers on this manual cover for future service reference. MFG. DATE PURCHASE DATE: Questions, problems, missing parts? Before returning to your retailer, call our customer service department at , 8:00 a.m.-6:00 p.m., EST, Monday-Thursday, 8:00 a.m.-5:00 p.m., EST, Friday. PRINTED IN CHINA

2 TABLE OF CONTENTS PRODUCT SPECIFICATIONS... 2 SAFETY INFORMATION... 3 CARE AND MAINTENANCE....3 ASSEMBLY INSTRUCTIONS....4/5 CUTTING HEIGHT ADJUSTMENT BLADE ADJUSTMENT CHECKING THE ADJUSTMENT TWO-YEAR LIMITED WARRANTY... 8 PARTS DIAGRAM /10 PRODUCT SPECIFICATIONS 16 IN. REE L MOWER Item No Cutting Path in. Height Adjustments /8-1- 7/8 in. Wheel Qty Weight Ib. 2

3 SAFETY INFORMATION Never place hands, fingers or feet inside the reel. Although a motor does not power this mower, when the wheels turn the reel spins and can cut. Never mow when grass is wet as it can be slippery. Do not use the reel mower while barefoot or while wearing sandals. Walk behind, never run, while using reel mower. Always make sure of your footing when using this reel mower. Never intentionally strike or hit trees, fences, etc. This can cause injuries or severely damage the reel mower mechanisms. Make sure your reel mower is in a safe operating condition. Do not attempt to operate this reel mower if damaged. Contact customer service or have the reel mower repaired by a qualified repair service provider before using. CARE AND MAINTENANCE 1. Minimum care is required to ensure smooth operation of your mower. 2. To avoid damage to mower or cutting blades, keep area to be mowed free from debris. 3. For best results, regularly apply lubricant to mower s cutting surfaces, cutting reel axle shaft and wheels. WARNING: Clean any grinding compound or debris from the cutter bar blade, reel blade, pinions and pawls. NOTE: Use industrial or valve lapping compound between grit. Lubricate the axle and pinion with a light film of wheel bearing grease. 3

4 ASSEMBLY INSTRUCTIONS Before attempting to assemble, empty carton and compare parts with parts list below. Note: Carefully remove the parts from the box. Inspect the parts to make sure no breakage or damage occurred during shipping. Do not discard the packing material until all parts are examined. If any parts are damaged or missing, please call for assistance. PACKING LIST 1-Top handle, 2-Center handle pieces, 2-Lower handle pieces, 8-Knobs, 8-Bolts, 8-Washers, 1-Reel mower body Top handle 2. Center handle pieces 3. Left lower handle 4. Right lower handle 5. Foam grip /8 in. bolts 7. Flat washer 8. Wing nut Tools Required Pliers (Not included) 7 4 Fig. 1 ASSEMBLING THE HANDLE: (Fig.1) NOTE: Do not completely tighten bolts until assembly is complete. 1. Insert the two center handle pieces (2) into the left and right side of the top handle (1) and secure with two 1-3/8in. bolts (6), flat washer (7) and wing nuts (8) provided. 2. Connect the right lower handle (4) with the left lower handle (3) and secure with two 1-3/8in. bolts (6), flat washer (7) and wing nuts (8) provided. 3. Attach the top handle subassembly previously assembled, to the lower handle subassembly using four 1-3/8in. bolts (6),flat washer (7) and wing nuts (8) provided. 4. Tighten all the wing nuts on the joints of the handle assembly. 4

5 ATTACHING THE HANDLE TO THE MOWER BASE: (Fig.2) 1. Align holes (1) at the lower end of each handle arm with short posts (2) extending from the mower base side plates. Slide lower ends of handle arms onto posts. 2. After handle arm holes are on posts, use pliers to snap C-clips (1) onto the slotted (2) posts on both sides to secure handle. 1 Fig

6 OPERATION CUTTING HEIGHT ADJUSTMENT: (Fig. 3) 1. The cutting height of the 16 in. reel mower can be adjusted from 5/8 1-7/8 in. using the roller assembly. 2. For the lowest cutting position, loosen and remove the adjust ment nuts on both sides of roller assembly. Position bolt through the bottom hole of the plastic roller bracket and top hole of the mower side plate. 3. For highest cutting position, loosen and remove the adjustment nuts on both sides of roller assembly. Position bolt through the top hole of the plastic roller bracket and the bottom hole of the mower side plate. 4. For other cutting heights, position bolts through the preset height locations. Height adjustment nut Fig. 3 6

7 OPERATION MOWER BLADE ADJUSTMENT: (Fig. 4) WARNING: BLADES ARE EXTREMELY SHARP. TO AVOID INJURY, DO NOT TOUCH BLADES WHEN MAKING ADJUSTMENT. Note: Blades are factory adjusted. Misalignment can occur, often caused by blades being too loose or too tight. This can cause an uneven cut or difficulty pushing the mower. Each end of the cutting bar is adjusted separately. To move the blades closer to the cutting bar turn the adjustment nuts clockwise. To move the blades away from the cutting bar turn the adjustment nuts counterclockwise. Cutting bar blade adjustment nut Fig. 4 CAUTION: Αdjusting the screws for blade adjustments is a very sensitive procedure. A turn of 1/16 is considered a major adjustment. Βefore tightening one adjusting screw, make sure to loosen the opposite screw an equal amount. CHECKING THE ADJUSTMENT 1. Turn mower upside down. 2. Insert a piece of paper between cutter bar and reel blades, and slowly turn wheel by hand. 3. All blades should slice the paper evenly, along the entire length of the cutter bar while the reel turns smoothly. 4. If mower has an intermittent cut, adjustment should be made to the appropriate side of blades to attain proper cutting action. WARNING: Do not overtighten adjusting screws, as this could damage cutter bar. Both screws must be tight on final adjustment. 7

8 TWO-YEAR LIMITED WARRANTY The manufacturer warranties that this product is free from defects in material and workmanship for two (2) years from the date of the original purchase by the original purchaser only. THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER: Products sold damaged or incomplete, sold as is, sold reconditioned or used as rental equipment. Delivery, installation or normal adjustments explained in the owner s manual. Damage or liability caused by shipping, improper handling, improper installation, incorrect voltage or improper wiring, improper maintenance, improper modification, or the use of accessories and/or attachments not specifically recommended. Repairs necessary because of operator abuse or negligence, or the failure to install, operate, maintain and store the product according to the instructions in the owner s manual. Damage caused by cold, heat, rain, excessive humidity, corrosive environments and materials, or other contaminants. Expendable items that become worn during normal use. Cosmetic defects that do not interfere with tool functionality. Freight costs from customer to vendor. Repair and transportation costs of products or parts determined not to be defective. ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT. Some states do not allow the exclusion or limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may have other rights that vary from state to state. WARRANTY REPLACEMENT PARTS are available by calling the toll free number, :00 a.m.-6:00 p.m., EST, Monday-Thursday, 8:00 a.m.-5:00 p.m., EST, Friday. 8

9 PARTS DIAGRAM 9

10 PARTS DIAGRAM LIST Item Description Qty 1 Housing 1 2 Reel blades 1 3 Top push handle 1 4 Center handle pieces 2 5 Lower handle 2 6 Spring 2 7 Spring washer 2 8 Bearing 2 9 Wheel cover 2 10 Gear wheel 2 11 Pin 2 12 Shaft 1 13 Foam grip 1 14 Washer 2 15 Bolt 2 16 Wheel 2 17 Cutting bar adjustment lever 2 18 Flat washer 2 19 Height adjustment knob 2 20 Long rear roller 1 21 Short rear roller 2 22 Long shaft 1 23 Knob 8 24 Bolt 8 25 C-clip 2 26 Flat washer Locked nut 2 29 Shaft 2 30 Cutting height adjustment 2 10