Drawing A Crankcase, Cylinder, Muffler. Drawing A Crankcase, Cylinder, Muffler

Transcription

1 Drawing A Crankcase, Cylinder, Muffler Drawing A Crankcase, Cylinder, Muffler Crankcase, fan side 2-4, Roller bearing 12x24.5x Bushing Connector Crankcase 2, Valve Hollow rivet 5.5x0.5x Collar screw M Collar screw M Oil seal 12x20x Hose Pickup body Filler cap O ring 23x Gasket Crankshaft ( ) Spline screw IS-M4x Cylinder gasket Cylinder with piston Ø 40 mm Piston Ø 40 mm Piston ring Ø 40x1.2 mm Snap ring 9x Piston pin 9x5.6x Needle cage 9x12x Spline screw IS-M5x20 1 2

2 Drawing A Crankcase, Cylinder, Muffler Drawing A Crankcase, Cylinder, Muffler Muffler (1,3) Spline screw IS-M5x Bumper spike Chain catcher Spline screw IS-M5x Set of gaskets 10, 15,

3 Drawing B Oil pump, Clutch Drawing B Oil pump, Clutch Oil pump Pump piston Washer Compression spring Control bolt O-ring 4x Roll pin 2x Plug Connector Spline screw IS-M4x Grommet Cover Cover Spline screw IS-M4x Worm 3/8" Picco 6T Worm 3/8" Picco 7T (B) Worm 1/4" 8T (B) Needle cage 10x13x Chain sprocket 3/8" Picco 6T Set of spur sprocket/worm 3/8" Picco 7T (B) 16, Set of spur sprocket/worm 1/4" Picco 8T (B) 17, 21, Chain sprocket 1/4" 8T (B) Clutch Clutch shoe Retainer Tension spring Bumper strip Spur gear / chain adjusting screw kit Tensioner slide Thrust pad Cover Locking strip (B) 5 6

4 Drawing C Tank housing Drawing C Tank housing Tank housing (1,2) 3-6, 8-13, 18, Insulating plate Clamp Hose Elbow connector (1,2) Hose Grommet Hose Tank vent Filler cap O ring 25x Warning pictogram Pickup body Spline screw IS-M4x Slide Slide Hose Self-tapping screw P4x Bracket Loop Pan head self-tapping screw IS-P6x Annular buffer Self-tapping screw P4x Screw Cover 7 8

5 Drawing D Chain sprocket cover, Hand guard Drawing D Chain sprocket cover, Hand guard Chain sprocket cover Pin Insert Notched pin 5x Collar nut M Bumper strip Flat spring Limit stop Tension spring Lever E-clip Brake band Hand guard Cover Self-tapping screw P4x

6 Drawing E Ignition system Drawing E Ignition system Flywheel ( ) Collar nut M8x Cover Lead retainer Connector tag Ignition module Torsion spring Spark plug boot Lead retainer Spline screw IS-M4x Spark plug NGK CMR6H 11 12

7 Drawing F Rewind starter Drawing F Rewind starter Fan housing with rewind starter (1,2) Fan housing (1,2) Bushing (1,2) Rewind spring (1,2) Self-tapping screw P4x10 (1,2) Rope rotor (1,2) Pawl (1,2) Washer (1,2) Spring (1,2) Starter grip ElastoStart Ø 3 mm (1,2) 10, Starter rope Ø 3x750 mm (1,2) Starter rope Ø 3 mm x 30.5 m (B) (1,2) Cap (1,2) Segment (1,2) Spline screw IS-M4x16 (1,2) Pan head self-tapping screw IS-P5x16 (1,2) Model plate MS 201 T (1,2) 13 14

8 Drawing G Rewind starter ErgoStart/Easy2Start Drawing G Rewind starter ErgoStart/Easy2Start 15 16

9 Drawing H Handle housing, Handlebar Drawing H Handle housing, Handlebar Handle housing (1,2) 1, 2, Handle housing Handlebar (1,2) Pan head self-tapping screw IS-P6x Spring Bearing plug AV-Spring Pan head self-tapping screw IS-P5x Torsion spring Throttle trigger Lockout lever Switch shaft Double lever Choke rod Choke rod Double lever Throttle rod Wiring harness 19, Grommet (D) Contact spring Handle molding Self-tapping screw P4x Spline screw IS-M4x Gear lubricant 80 g (B) ( ) 17 18

10 Drawing J Air filter, Carburetor box cover Drawing J Air filter, Carburetor box cover Air filter, fleece Air filter (B) Spline screw IS-M5x Baffle O-ring 4x Filter base Carburetor box cover Twist lock Carburetor C1Q-S250 (1,2) Carburetor C1Q-S248 (1,2) ( ) Throttle rod Cover (1,2) Manifold Spline screw IS-M4x

11 Drawing K Carburetor C1Q-S250, C1Q-S248, C1Q-S214, C1Q-S188 Drawing K Carburetor C1Q-S250, C1Q-S248, C1Q-S214, C1Q-S Carburetor C1Q-S250 (1,2) 1-5,7-21,23,25,26, Carburetor C1Q-S248 (1,2) ( ) 1-5,7-19,22,23,25,26, Carburetor C1Q-S214 (C) (1,2) ( ) 1-5,7-19,22,24,25, Carburetor C1Q-S188 (C) (1,2) ( ) 1-4,6-19,22,24,25, Inlet needle (1,2) Spring (1,2) Inlet control lever (1,2) Spindle (1,2) Screw (1,2) Collar screw (1,2) ( ) Gasket (1,2) Metering diaphragm (1,2) End cover (1,2) O-ring 7x1.5 (1,2) Collar screw (1,2) Strainer (1,2) Pump diaphragm (1,2) Gasket (1,2) Pump cover (1,2) Idle speed adjustment screw (1,2) Oval head screw (1,2) High speed adjustment screw (1,2) Cap (1,2) Low speed adjustment screw (1,2) Cap (1,2) Low speed adjustment screw (1,2) ( ) Throttle lever (1,2) Throttle lever (1,2) ( ) Collar screw (1,2) Torsion spring (1,2) 21 22

12 Drawing K Carburetor C1Q-S250, C1Q-S248, C1Q-S214, C1Q-S188 Drawing K Carburetor C1Q-S250, C1Q-S248, C1Q-S214, C1Q-S Torsion spring (1,2) ( ) Detent lever (1,2) Lever (1,2) Lever (1,2) Screw (1,2) Sleeve (1,2) Throttle rod (1,2) Set of carburetor parts (1,2) 7, 8, 13,

13 Drawing L Carburetor C1Q-S251, C1Q-S249, C1Q-S215, C1Q-S189 Drawing L Carburetor C1Q-S251, C1Q-S249, C1Q-S215, C1Q-S

14 Drawing M Tools, Extras Drawing M Tools, Extras Tool kit Combination wrench Screwdriver T27x120x Tool roll Screwdriver Locking strip (B) Filing gauge (B) Chain scabbard Tophandle 35 cm Chain scabbard Tophandle 40 cm Tag 27 28