Step 3.) Remove the factory air box bracket (if still equipped). *Retain one bolt for later use in Step 5.

Transcription

1 1 PLEASE NOTE: Hi-Tuned Performance Products (HTP) recommends that this product be installed by a professional. HTP is not liable for any parts or any damage incurred due to improper installation or use. If you have questions or concerns about this product or the installation, we encourage you to contact us directly at sales@hitunedperformance.com or by calling TOOLS NEEDED: - 10mm Socket - 12mm Socket Step 1.) Remove the OEM battery by first disconnecting the negative terminal and then the positive terminal. Using a 10mm socket, remove the OEM battery tray. Step 2.) Re-install (2) 10mm bolts to secure wiring bracket Step 3.) Remove the factory air box bracket (if still equipped). *Retain one bolt for later use in Step 5. Step 4.) Remove 10mm nut from fuse box mount & retain for use in Step 5. Step 5.) Install preassembled terminal adapter bracket using 10mm nut and 12mm bolt.

2 2 Step 6.) Moving to the trunk, remove the jack and tire iron. Tire iron can be stowed next to spare tire. *Set aside jack for relocation with bracket provided in Step 25. Step 7.) Remove 5 retaining clips from the passenger side trunk panel. Step 8.) Pull interior panel back and feed (1) 10mm black bolt provided through from the back of the metal panel, line up with pre-existing hole in trunk interior panel and the battery tray mounting point. Thread on corresponding nut and using a 10mm socket or wrench, tighten the bolt all the way down.

3 3 Step 9.) Using a 3/8 nut driver, install the (3) #14 x 1mm self-drilling/self-tapping screws provided. CAUTION: DO NOT OVER-TIGHTEN! *Optional: For ease of installation, holes may be pre-drilled if desired using a 1/8 drill bit. Step 10.) Install (1) 5/16 threaded rod into the back hole of the battery tray. Step 11.) Remove (5) retaining clips from the back interior panel and remove panel. Step 11a.) Remove the driver side front and rear door sill panels by working fingers front to rear under each panel and gently pulling upwards to release the clips.

4 4 Step 12.) Starting from the battery tray, feed the eyelet end of the power cable behind the rear seat and down under the rear and front driver side sill panels. Step 13.) Inside the driver s door near the floor, remove the panel labeled Fuse Box Step 14.) Route the power cable under the fuse panel and up to the wiring grommet at the firewall. Step 15.) Pull back the sound deadening material to expose the rubber boot. Using an X-Acto knife, cut a slit into the top part of the rubber boot indicated by the arrow in the bottom right picture.

5 5 Step 16.) Push eyelet through the firewall grommet and from the engine bay, pull the cable through. *Note: Brake/Parts Cleaner may be used on the cable to ease it through the grommet. Step 17.) Install the positive and negative OEM cables to the terminal adapter bracket. Step 18.) Install the provided dust boot over the eyelet end of the power cable.

6 6 Step 19.) Install power cable onto positive stud using a 9/16 wrench. Step 20.) CAUTION: DO NOT REMOVE OEM CHASSIS GROUND BOLT! Step 21.) *Important: Before proceeding, pull any slack in the power cable back towards the trunk. Neatly zip tie the power cable to the A/C line.

7 7 Step 22.) Moving back to the trunk- cover & securely zip tie the power cable using the provided split wire loom to protect cable against seat edges & brackets. Step 23.) Route ground cable and secure the eyelet to the top 12mm bracket bolt. Step 24.) Install the battery into the tray using the provided hold down strap and remaining threaded rod and nuts. STOP: IF THE OPTIONAL CIRCUIT BREAKER ADD-ON IS BEING USED, BYPASS STEP 24a AND JUMP TO THE CIRCUIT BREAKER INSTALLATION INSTRUCTIONS FOUND AT THE END OF THIS GUIDE. IF YOU ARE NOT USING THE OPTIONAL ADD-ON CIRCUIT BREAKER, PROCEED TO STEP 24a. Step 24a.) Secure the positive terminal first and tighten. Then connect the negative terminal.

8 Step 25.) Install the jack relocation bracket on the driver side of the trunk as shown by first removing the three clips indicated below and pulling back the panel to feed (2) 10mm black bolts provided through the pre-existing holes in panelling. Install the jack into the bracket. Using the factory t-bolt, pinch the tabs inwards and tighten. 8 Step 26.) Re-install all trunk and door sill panels. CIRCUIT BREAKER INSTALLTION INSTRUCTIONS: 1.) Attach the circuit breaker to the hold down strap as shown using a 4mm allen wrench and hardware provided. 2.) Connect the power cable (which is running to the engine bay) to the auxiliary stud and tighten using a 5/16 socket or wrench. 3.) From the circuit breaker battery stud (labeled BATT ), connect the lead to the battery post and tighten. 4.) Attach the negative terminal. 5.) Return to Step 25 to complete jack relocation installation.