Wiring Centre Box Cat. No. TRT049

Transcription

1 Port System (Y-Plan) Model TRT0 S 0V, 0Hz BS 00 --, -- at. o. TRT0 : TRT0 TRT0 HW H HW H OFF OFF O O 0 0 ote: inks shown Grey HW (O) Brown () Blue () eutral not TRT0 and TRT0 S Timeguard td. Victory Park, 00 dgware Road, ondon W D Tel: 00-- TRT00 TRT0/ TRT0 TRT0 within years of the date of purchase, please For years and or any difficulty in the first year telephone the helpline on WIRIG TR TRT0 Year Guarantee 0 () (O) Model TRT HPI -0- TRT0_00x0_Instructions.indd //0 ::

2 . Introduction TRT0 Wiring entre Rear View The TRT0 is a cost effective and stylish wiring centre, with plenty of wiring space, and easily accessible terminals. There are cable clamps to secure incoming and outgoing cables. It is designed for internal use only. Wiring centres simplify installation and make checking the circuit easier. This wiring centre is suitable for all popular heating systems. Wiring diagrams are supplied for the two most popular, S-plan and Y-plan. This guide assumes that can identify the required leads from the boiler, pump and other controls. The electrical supply must be isolated before removing the front cover. BM0 MX URRT 0 0V ~ 0Hz TRT0 Wiring entre Front View Fig. a over fixing screws Tough plastic enclosure TRT0 Wiring entre Inside View 0 Multiple fixing holes able entry knock outs Wiring terminals able clamps arth terminals Fig. Fig. b

3 ote: inks shown WIRIG TR TRT0 Model TRT0 () (O) 0 0 Brown () S H O HW O H OFF HW OFF Grey HW (O) ontents Port System (S-Plan) TRT0 Wiring entre x wire link x wall plugs x screws x circuit identification label. Installation This product must be installed in accordance with the appropriate building and wiring regulations. In all cases if there is a doubt as to how to proceed with an installation consult a qualified electrician, your local authority s building control department or the Timeguard helpline (00 0 0). lways isolate the mains supply before removing the cover from the TRT0. The TRT0 is designed to be surface mounted. Isolate 0V mains supply. Remove front cover from unit, by undoing the retaining screws. Fix back plate securely to the wall, using the screws (and wall plugs) provided. The cable knockouts should be at the bottom. Remove the required break-offs from the bottom edge or knock-outs from the rear to accommodate the cables (a mixture of rear and bottom entries can be used if appropriate). llow sufficient excess cable to wire up the unit, but not too much to make it difficult to close the cover. Model TRT0 Blue () : TRT0 TRT0 HW onnect the conductors to the relevant terminal, according to the wiring diagrams below. If earth continuity is required, please use the earth terminals on the right hand side. TRT00 TRT0/ TRT0 TRT0 S eutral not TRT0 and TRT0 Blue () Brown () Grey HW (O) H Restore mains to the unit after checking all system wiring is complete and replacing cover.

4 Port System (Y-Plan) Model TRT0 S 0V, 0Hz BS 00 --, -- at. o. TRT0 : TRT0 TRT0 HW H HW H OFF OFF O O 0 0 ote: inks shown Grey HW (O) Brown () Blue () eutral not TRT0 and TRT0 S Timeguard td. Victory Park, 00 dgware Road, ondon W D Tel: 00-- TRT00 TRT0/ TRT0 TRT0 within years of the date of purchase, please For years and or any difficulty in the first year telephone the helpline on WIRIG TR TRT0 Year Guarantee 0 () (O) Model TRT HPI -0- TRT0_00x0_Instructions.indd //0 ::

5 Port System (Y-Plan) Model TRT0 S 0V, 0Hz BS 00 --, -- at. o. TRT0 : TRT0 TRT0 HW H HW H OFF OFF O O 0 0 ote: inks shown Grey HW (O) Brown () Blue () eutral not TRT0 and TRT0 S Timeguard td. Victory Park, 00 dgware Road, ondon W D Tel: 00-- TRT00 TRT0/ TRT0 TRT0 within years of the date of purchase, please For years and or any difficulty in the first year telephone the helpline on WIRIG TR TRT0 Year Guarantee 0 () (O) Model TRT HPI -0- TRT0_00x0_Instructions.indd //0 ::